Search Documents

By S J. Kim, S W. Kim, L Tomas da Rocha, S Jung

Al2O3 has been regarded as a harmful gangue component in iron ore, especially causing reduction degradation in industrial sintering of iron ore. The current study aimed to utilise low-grade iron ore containing high Al2O3 content in sintering process. In order to counteract the adverse effect of Al2O3 on reduction behaviour of iron ore sinter, mill-scale and calcined dolomite were chosen as FeO- and MgO-bearing materials. Firstly, mill-scale was added to high Al2O3 sinter and addition was optimised as 10 wt per cent, then calcined dolomite was added further. Magnetite and magnesio-ferrite were identified as the major phases in iron ore sinter when adding mill-scale and calcined dolomite. As the dosage of calcined dolomite increased beyond 4 wt per cent of in sinter mix, unreacted MgO particles were observed, which is ascribed to the limitation of MgO dissolution into magnetite matrix. Both mill-scale and calcined dolomite were effective in improving compressive load and Reduction Disintegration Index (RDI) of iron ore sinter although its reduction degree was highly decreased. The addition of both FeO and MgO-bearing materials to high Al2O3 sinter has a potential to improve the sinter quality, also contribute to the recycling of industrial by-product. However, the amount should be optimised in views of phase development and deterioration of reducibility.

Jun 19, 2024

By X. P. Zheng, H. K. Lin

Barium fluorophlogopites were synthesized in the laboratory to investigate the effects of composition and crystal parameters on surface properties and floatability. The negative surface charge of mica is determined by the barium content, the crystal cell volume, the distance between the layer structure and the Ba-O bond length. The higher the barium content, the larger the cell volume and distance between the layer structure, and the longer the Ba-0 bond, the more negatively charged the surface is, and, hence, the more easily adsorbed are cationic collectors. When an anionic collector (sodium oleate) is used, barium oleate forms on the mica surface and hence chemical adsorption occurs.

Jan 1, 1995

By T. Nghipulile, G. Dzinomwa, J. Kurasha, M. Amwaama, B. Mapani, K. Maweja, T. E. Moongo

The effect of mineralogy on the grindability was investigated using three copper ores – two sulphides and one oxide. The dominant copper minerals were identified by optical microscopy and mineral chemistry derived from SEM-EDS analysis. The sample designated sulphide 1 was borniterich, sulphide 2 ore was mainly chalcopyrite, and the oxide ore was predominantly malachite and minor azurite. The gangue minerals were identified using semi-qualitative XRD analysis. Sulphide 1 contained more than 80% (w/w) of quartz compared to about 70% in the other two ores. The Bond work indices were 13.8, 21.6, and 17.3 kWh/t for sulphide 1, sulphide 2, and oxide ore respectively. This suggested that the chalcopyrite-rich ore is the hardest, while the malachite-rich ore has intermediate hardness, and the bornite-rich ore is the softest. The brittleness indices of the ores were calculated using the chemical composition of the gangue, and a good correlation between brittleness indices and Bond work indices was observed, which highlights the importance of the gangue composition in determining the fracture behaviour of the ores. There is scope for further investigation into the relationship between ore mineralogy and comminution behaviour using other breakage characterization techniques.

Mar 30, 2023

By Zygmunt Kowalczyk

"A theory permitting the determination of expected surface deformations for planned underground exploitation is proposed and discussed in this paper. The relations between surface subsidence and various methods of mining are analyzed, and allowable horizontal .deformations for protected objects, according to the degree of their significance, are reviewed."

Jan 1, 1966

By A. K. Alzo?ubi

Block toppling in natural rock slopes has been under investigation since the 1970?s. De Freitas and Watters (1973) introduced the term ?toppling? to describe the movements of rock slopes by rotation in steeply dipping beds. The Lornex pit case history from British Columbia (Canada) was chosen to study the effect of mining on the stability of toppling rock slopes. A discrete element approach that allows fracturing of intact material was applied successfully to model the composite rock slide-rock topple movement. Three main movement modes were observed in the field and the numerical model; the sliding of the top of the slope exposed normal scarps, the toppling at the middle part of the slope exposed obsequent scarps facing opposite to the slope face, and dilation of the rock caused by fracturing at the toe formed loose material. The development of the rupture surface at the toe of the slope was traced and did not evolve into a continuous rupture surface throughout the slope both in the field and the numerical simulation. Good agreement was achieved between the deformations recorded in the field and the numerical simulation.

Jun 1, 2012

By Robert H. Raring

Viewed abstractly, a mill may be defined as a mineral processing facility located somewhere between the mine and the tailings storage area, Just how mining operations and the demands of tailings storage affect mill design is, the subject of this paper. At the outset, it will be readily acknowledged that no two installations can, or ever will be the same. At one extreme is the bucket line dredge where the distance between the ?mine? and the tailings area is measured in terms of tens of feet. At the other extreme, the large open pit copper mines are frequently spread across twenty, miles or so of countryside with the ore moving to the mill, as exemplified by the operations at Bingham Canyon, Ray, or Ruth - the "upstream" counterparts of Garfield, Hayden and McGill. In each of these cases, mill location was largely determined by requirements for tailings storage and/or water supply.

Jan 1, 1961

By R. Venugopal, V. K. Saxena, Veerendra Singh

"Ore morphology plays a vital role during the milling and liberation of minerals. This study was carried out to understand the role of mineral crystallography and mineral interfaces on the milling and liberation processes. Data related to mineral crystallography, Vickers Hardness Number and beneficiation processes were collected from literature, and detailed statistical analysis was conducted to relate these parameters. Review of the crystallographic information of minerals present in ores indicates that molecular weight and cell parameters significantly affect milling and liberation characteristics. Mineral interfaces were classified into the three categories of coherent crystals, semi-coherent and incoherent crystals, and breakage behaviors were studied. The studied cases revealed that these material interfaces control the micropore properties that play a vital role in the initiation of intergranular and intercrystalline fractures which occur in siliceous manganese ores and dolomite as a result of thermal treatment. In contrast, banded hematite jasper and coal exhibited a much more complex fracture pattern due to their coherent interfaces and finer physical associations. This study explains the effect of the various types of interfaces on milling, and the approach can be helpful in developing a methodology to enhance mineral liberation with minimum energy consumption.IntroductionComminution is a vital unit operation in the mineralprocessing, cement-making, power-generation and pharmaceutical industries. Its importance in mineral beneficiation operations is increasing every year as a result of the growing need to exploit lower-grade ore bodies and process reject materials (Blazy et al., 1994; DOE, 2005). Low-grade ores require significant energy during grinding to liberate the valuable minerals, which are further separated from the gangues by various beneficiation methods. Various attempts have been made to enhance mineral liberation during grinding to minimize energy consumption. Most of these studies focused on the analyses of the compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang et al., 2011; Singh et al., 2012). However, many of these efforts had limited success, and there is a need to see the problem from a fresh perspective."

Jan 1, 2015

By J. Rostami, P. P. Nelson, A. Khetwaln

Tunnel boring machines (TBMs) can be considered as the method of choice for tunneling in many projects due to the high level of efficiency and high potential productivity, safety, and applicability in a variety of subsurface conditions. The muck transportation system in a TBM tunneling operation plays a significant role in the process and impacts the overall performance of the machine. This paper introduces a recently developed method of simulating TBM operation through discrete event simulation (DES), which allows for tracking of the various activities, incurred downtimes in the operations, and overall machine utilization. The study presented here compares two different muck transportation systems, conveyor and rail, under similar geological conditions to quantify the impacts of the choice of muck transportation systems on machine utilization. The results show the applicability and extent of redundancy in the use of the two systems relative to machine capabilities and their sensitivity to geological conditions.

Jun 13, 2021

By D J. Williams, C Zhang, F E. Herrera Cabrera

Farming on bauxite residue using screw propelled equipment (SPE) has been commonly practised to accelerate dewatering and as it promotes consolidation and enhances storage capacity. However, it is unclear when and how often farming should be conducted during the transition of bauxite residue from slurry to dry solids and how deep each slurry deposition should be. To address this issue, three desiccation tanks were established in the laboratory to investigate how much farming could enhance the desiccation and consolidation of tailings. The cuboid tanks, of 350 mm in height and 300 mm in width and length and with an opening on the top, were placed on load cells to monitor the water loss during desiccation and were instrumented with moisture and suction sensors designed and developed at the University of Queensland to measure the water content profile of the residue. The bauxite residue, composed of silt-size particles with low plasticity, was hydraulically deposited in the tanks as a slurry at 27% solid content, resulting in 100 mm depth of solid material settling. Evaporation was enhanced by placing two identical electrical fans above the tanks. Two phases were conducted. In the first phase, the two tanks were left untouched for evaluating non farmed conditions and for calibrating sensors, while in the second phase, three tanks were subjected to atemporal farming using purpose-built screw propelled equipment. The experiment was terminated when the residue was completely desiccated. This paper reports on the instrumented tank set-up and the results obtained to date.

Jul 1, 2021

By David Whalen

Mobile equipment in oil sand mining operations experience more maintenance problems than similar equipment in other surface mines, due to soft underfoot conditions. Oil sand properties are known to vary with temperature, bitumen content and previous loading cycles. One of the challenges is the widely variable underfoot pressure which supports shovels and trucks. In the case of a heavy hauler driving on in-pit roads, each tire is supported by a different ground stiffness resulting in an apparent uneven surface. Driving over uneven ground causes twist in the truck frame, which is transmitted to the dump body. Through a finite element analysis of a haul truck dump body, it was shown that slight frame twists produce localized stresses in the intersections of the floor stiffeners. These stresses are at times greater than those resulting from the maximum ore weight and are primarily responsible for cracking in these intersections. Syncrude maintains high quality haul roads, which are constructed of gravel, and makes every effort to keep the shovel pit roads as smooth as possible. This problem cannot be avoided through operational practices only and must also be accounted for in the design of haul truck bodies.

May 1, 2003

By K. Aoki, N. Kameda, T. Esaki

The shortage of adequate construction sites and their difficult location has compelled many engineering structures to be planned in old mining areas in Japan. This paper shows, first, the characteristics of the excavated underground environment and next, the necessary preventive measures during construction of surface structures. Where the depth of a mined out area is relatively shallow, there is a tendency of cave-in consequent to surface loadings. The effect of surface loadings is inversely proportional to the depth of goals. Finally, a power plant project is studied as an example.

Jan 1, 1984

By N. H. J. Freire, D. Majuste

In this paper, the effects of some organic compounds on the current efficiency, cell voltage and specific energy consumption during nickel electrowinning, and on the deposit features (morphology, crystallographic orientation and nanohardness) were described. The organics tested here (extractant, diluent, flocculant, lubricating oil and acid mist suppressant) are currently used in industrial plants. The results indicated that only the flocculant and acid mist suppressant exhibit relevant negative impacts on the current efficiency and energy consumption. The current efficiency dropped from 93.6 % (organic-free solutions) to 86.0 % and to 92.8% in electrolytes containing 100 mg.L-1 of acid mist suppressant and flocculant, respectively. At this concentration, their addition to the electrolyte led to increases of the specific energy consumption in the order of 18 % (acid mist supressant) and 2 % (flocculant). Cyclic voltammetry showed that Ni nucleation occurs at more negative potentials at 50 and 100 mg.L-1 of these organics in the electrolyte, thus indicating an inhibition of the deposition process. The deposit quality decreased at the higher concentration of all organics, when more hydrogen pitting was observed. The acid mist suppressant caused delamination of the Ni deposit at 50 and 100 mg.L-1. The addition of 100 mg.L-1 of flocculant and acid mist suppressant to the electrolyte increased the nanohardness of the deposit around 31 and 72%, respectively. The increase in Ni deposit hardness may lead to a decrease in the material ductility, thereby affecting the stripping and cutting of Ni sheets. Our findings may be helpful since strong adverse effect of some organics that may be present in the electrolyte were identified, thus the industry can control and optimize the organic´s dosage in the corresponding operations.

Jan 1, 2016

By Árpád B. Palotás, Adel F. Sarofim, John B. Vander Sande, Paolo Ciambelli, Lenore Rainey

"The evolution during oxidation of the internal structure of soot and carbon black particles was studied using high-resolution transmission electron microscopy (HRTEM) and an image analysis system. Increasing ordering to the carbon structure with increasing oxidation is observed. Measures of the increased order are increases in the fractional coverage of a cross section of the particles with a layered structure, a decrease in the mean interlayer spacing, and a decrease in the spread of the interlayer spacing. The changing structure of the carbon black impacts its properties, such as the rate of oxidation.There is considerable interest in the study of the structural changes of carbonaceous materials as a function of oxidation. Davis et al.1 measured the variation of carbon dioxide surface area of various coals as a function of residence time in a flow reactor. HRTEM measurements revealed that crystallite dimensions and interlayer spacings are altered by combustion. Ishiguro et al.2 showed that oxidation alters the structure of diesel soot. The aim of our current research is to develop a better understanding of the microstructural reordering of carbon blacks with implications to their properties. The carbon blacks used in this research have already been studied and their reactivities as a function of oxidation measured.3The methodology used in this work has already been described in detail elsewhere.4 This paper presents an application to quantify the structural changes of carbon black particles as a function of oxidation and graphitization. The technique used is based on the use of HRTEM (high-resolution transmission electron microscopy) and computational image analysis.It is well-known that carbonaceous materials like graphite, soots, coals, chars, etc., possess characteristic structural appearances which can vary from mostly random or amorphous to a perfectly ordered graphitic crystalline structure. The carbon structure has been variously described as turbostratic5 or as crumpled sheets6 to indicate that parallel layering, reminiscent of graphite, is observed over dimensions of nanometers but that these planes or crystallites show disorder over larger scales. The degree of order of such structures is strongly dependent on the thermal treatment of the material as well as the composition of the source of the carbonaceous material. The value of electron micros¬copy in studying the morphology of such materials has been well established,2,7,8 although only a few attempts toward quantification have been made.The sample observed was carbon black CB330 from De¬gussa. One set of carbon black samples were oxidized in a thermo-gravimetric analyzer (TGA) in air at 575 0C, so that the conversion varied from 0 to 96%. Another set of carbon black samples were graphitized (Graphpac-GB by ALLTECH) and then oxidized in the TGA at 680 °C until 92% burnout was reached. The latter samples are called GB 0% and GB 92%, respectively.For the HRTEM observation a small portion of each sample was ultrasonically dispersed in ethanol. The suspension was deposited dropwise on a copper TEM grid coated with a lacey carbon film. The examination of the samples was carried out on areas that extend over the holes in the supporting film in order to avoid interference from the amorphous carbon background film An oriented gold crystal was used as a calibration standard and subjected to the same techniques as the carbon black samples."

Jan 1, 1998

By Hiroyuki Matsuura

The effects of P2OS or Na2O addition on the reaction rate of CO2 dissociation on the surface of FexO-base molten oxides was investigated at I 773K by isotope exchange method 1-6. The rate constant decreased with increasing P2Os content of molten oxides and the residual rate constant was observed at high P2OS content. On the other hand, the rate constant increased with increasing Na20 content for FexO-SiO2 melts, The rate constant was evaluated by the composition of oxides and the rate controlling step of CO2 dissociation was discussed.

Jan 1, 2003

By Hiroyuki Matsuura

The effects of P20S or Na20 addition on the reaction rate of CO2 dissociation on the surface of FexO-base molten oxides was investigated at 1773K by isotope exchange methodl-6_ The rate constant decreased with increasing P20S content of molten oxides and the residual rate constant was observed at high P20S content On the other hand, the rate constant increased with increasing Na2O content for FexO-SiO2 melts. The rate constant was evaluated by the composition of oxides and the rate controlling step of CO2 dissociation was discussed.

Jan 1, 2003

By I. Gombköto

In the EU-region, the automatically operated approximately 200 (rotating hammer) shredder plants processing large technical equipment (end-of-life vehicles, large household appliances) annually produces 8-9 million tons of non-metallic grinded by-product, which ends in landfills, without recovery. Although this by-product is organic material, still contains large amount of metal components worth recycling. These operations, such as shredding and processing end of life vehicles or mixed metal components are a growing market and it is become more potential if EU directive 2002/96/EC will become obligatory for new member and candidate countries and they have to apply EU regulations. Eddy current separators (ECS) are one of the most important units of separation of non-ferrous metals from insulators in waste recycling. The product of ECS processing of shredded ELV?s is usually a mixture of Al, Cu, Brass and stainless steel. This mixture has relatively low price on the market, while purified metal products are required by smelters for which shredder operators are able to get even higher price. Our aim at University of Miskolc was to find solution producing pure metal products using dry separation processes. Authors are presenting a possible solution, using ECS. Institute of Raw Material Preparation and Environmental Processing possesses an ECS, equipped with 305 mm wide belt, and a concentric magnetic rotor. The subject of our work was to investigate the behaviour of model particles with different shape, conductivity (aluminium and brass), orientation and size in order to separate Al and Brass. We used model particles with similar shapes of shredder plant originated ones. The magnetic flux and magnetic frequency was constant and derived by the design of the rotor. During our research work, belt speed and rotor speed of ECS were varied. The particle distance and trajectory caused by throwing was determined and the results are reported in this paper.

Sep 1, 2012

The heat of immersion of coals in different immersional liquids is measured as a function of particle size and moisture content. Decrease in particle size shows a concomitant increase in the heat of immersion. The heat of immersion is dependent upon the nature of immersional fluids. In addition the nature of moisture present in coal influences the heat of immersion.

Jan 1, 1993

By S Nkwanyana, I Govender

Batch experiments in a 0.6 m diameter mill have shown that improvements of about 13 per cent in the efficiency of energy utilisation can be realised in ball mills by replacing 25 per cent of the ball charge by an equivalent volume of cost-free critical size pebbles from AG/SAG mills. For a mill of a given size, speed and charge filling, the rate of size reduction of ore particles depends on (i) the frequency of grinding media collisions (ii) the probability of capture of ore particles between the colliding grinding media (iii) the probability of fracture of the captured particles. The probability of fracture depends on the magnitude of collision energy. The distribution of collision energy into shear and impact events determines the relative strengths of attrition breakage and impact breakage. The efficiency of energy utilisation depends on which of the two mechanisms of breakage is more desirable in a particular milling stage. In this paper collision data from a series of DEM simulations of a mill charged with steel media and a mixture of steel media and pebbles is presented in energy spectra and spatial distribution maps. The data provides the necessary detail to elucidate the improvements in the efficiency of energy utilisation in ball mills when using a mixture of pebbles and steel media.

Aug 24, 2022

By Charles David

This work aimed at evaluating the effect of pre-strain of Lean Duplex UNS S32304 on anodic dissolution and hydrogen evolution reaction rates in acidic chloride media. Interrupted tensile testing was employed in order to generate different deformation levels. Potentiodynamic experiments allowed to detect a decrease on the cathodic and anodic reaction rates as a consequence of plastic deformation. A non-linear evolution of corrosion rates was observed, probably as a consequence of the evolution of specific dislocation structures in the material. Strain also caused a slight ennoblement of the ferritic phase, while austenite became a little less noble. These behaviors are analyzed in terms of residual stresses, characterized by X-ray diffraction.

Aug 17, 2017

By R. L. Eadie, J. L. Luo

The effect of plastic deformation on near-neutral pH stress corrosion cracking (SCC) also known as environmentally assisted cracking was studied by cracking rate measurements. All the tests were conducted in a synthetic near-neutral pH solution. The traditional potential drop tests using compact toughness (C-T) specimens with 2-3 mm long pre-cracks showed varying plastic deformation by rolling would increase the material's susceptibility to SCC. This was confirmed by cyclic loading tests using double notched flat tensile specimens with 200-300 µm long pre-cracks which gave the same results that the specimen with large scale plastic deformation by tensile loading had a relatively faster crack growth rate than that with only small scale plastic deformation.

Jan 1, 2005