Search Documents

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-cu-yd) transit mixer and a shotcrete spray boon carrier, is used by a two-man crew to transport and place up to 25 m3 (32 cu-yd) of steel fiber reinforced, dry, silica fume shotcrete per 11-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control are performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1992

By W. Basuki, B. Setyotomo, L. Hakim, R. Hendrajaya

Due to high crack sensitivity of slab product of gas and oil line pipe application, its steel making process and alloy composition were evaluated and then improved to overcome its critical solidification process and reduced surface defects. The study was conducted at Slab Steel Plant Krakatau Steel. The purpose was to improve slab surface quality by reducing surface defects so that the slab surface doesn't need to be totally repaired. The method applied was by performing plant trial process, which the secondary process parameters such as alloying method and the casting parameters such as casting powder selection, metallurgical cooling, mould level control, and superheat were continuously monitored and then adjusted to the surface quality of the product. Based on the calculation of Ferrite potential of the steel, the chemical composition was designed to achieve optimum casting parameters in order to avoid high shrinkage during solidification. The results of the study are decreased surface defect quantity, and smooth casting process. The quantity of crack decreased by almost 90%. The slab surface repairing was significantly reduced from 85. % to less than 10%. These new casting parameters and developed alloy composition are then used and standardized for the mass production of the steel.

Jan 1, 2005

By C. C. Pretorius

3D seismic surveys have become a well-accepted method of imaging sub-surface geology in the Bushveld Basin. Because both the seismic sources and receivers are placed at surface, most surveys are limited to imaging faults with >=7 m throw. However, some areas such as shaft infrastructure can benefit from the ability to detect smaller structures prior to shaft sinking. Borehole radar and logs such as the acoustic televiewer can identify these structures in the shaft barrel, but not within -200 m from the shaft. Therefore, Anglo Platinum has developed the method of high-resolution 3D vertical seismic profiles (VSPs) for structural sterilization of shaft sites prior to shaft sinking. VSPs utilize a surface source and sub-surface receivers deployed down a borehole. This means that seismic energy goes through the near surface only once, and therefore suffers less frequency loss than when both source and receivers are on surface. Furthermore, VSPs can record 3 component (3C) data which comprises P wave, Sh (horizontal) and Sv (vertical) wavemodes. Because S waves travel at about 0.6 of the velocity of a P wave, shorter wavelengths and therefore higher resolutions are possible using S wave data. VSPs were first used in their one dimensional, zero offset, mode to correlate borehole geology with seismic stratigraphy within seismic surveys. This showed that VSPs record -30% higher frequencies than surface seismic surveys. The program then applied two dimensional VSPs to the problem of imaging geological structure close to a borehole. 2D VSPs confirmed that high frequency results could be achieved, and that this enabled a more accurate image of the Merensky Reef than could be achieved by surface seismic data. Finally, the program has achieved the successful recording and processing of 3D VSP data, with both compressional and shear wavemodes giving a high resolution structural result. Although P wave data gives -30% frequency improvement over surface seismic surveys, S wave data can give as much as 80% improvement, further improving the structural image achieved. The high fixed costs of VSP surveys mean that they should ideally be run in multi-client batches, which can reduce the per borehole cost by up to 50%. Their application is anticipated to be on high value capital infrastructure with a geological risk from faults which are not imaged by surface seismics-generally in the sub-7 m range. Keywords VSP, 3D seismic, bushveld, platinum, resolution, imaging, shear waves, shaft sinking.

Jan 1, 2011

By Karen Mikkola, Gerald Luttrell, Jaisen Kohmuench, Glen Oswald, Michael Mankosa, Tracy Westerfield

Hydraulic separators are commonly used for particle size classification and gravity concentration of minerals and coal. Unfortunately, the efficiency of these processes can be quite low due to poor equipment design and variations in feed consistency. To help alleviate these problems, an industry-driven R&D program has been undertaken to develop a new generation of hydraulic separators that are more efficient and less costly to operate and maintain. Two of the most promising technologies, the CrossFlow and HydroFloat separators, have now been tested at industrial sites. The data obtained from these sites have been used to illustrate the potential performance improvements that can be realized through the application of these high-efficiency separators.

Jan 1, 2005

By Viacheslav Lyakhov, Cornelis H. Iestra, Victor I. Beloborodov, Vitaliy Bogdanovich

The results of a study and effective use of flotation for processing of ores with complex mineral composition containing fine-disseminated minerals with high specific density are presented in the paper. The object of research was complex baddeleyite-containing ore from Kovdor deposit (The Kola peninsula, Russia). Baddeleyite is a valuable, rare mineral, natural Zirconium dioxide with 5.8 - 6.0g / cm density, grade content 0.15 - 0.17 and dissemination less than 0.2 mm. The authors carried out a thorough investigation of baddeleyite- containing products selected in different sites of gravity flowsheet. It was determined that due to similar specific weight some sulphide minerals (pyrite, pyrrhotite) come into concentrate together with baddeleyite and, also, minerals of pyrochlores group (hatchettolite). The results obtained revealed the possibility of use the flotation for retreating rough baddeleyite concentrate. he given gravity concentrate has a number of specific features, e. g. high density of its minerals which, in its turn, provides for high speed of sedimentation of solid phase in pulp, and for the presence of large amount of sulphide minerals (up to 10%) having good flotability. With these features being taken into account a technology for flotation of baddeleyite-containing products after their preliminary gravity concentration has been developed (up to 5 - 10% Zirconium dioxide). The technology has three flotation stages. At the first one the reverse flotation of baddeleyite is carried out during which "light" minerals (forsterite. apatite and carbonites) come into froth product and at the second one flotation of sulphide minerals and at the third one direct flotation of baddeleyite is performed from the underflow product. The following reagents were used for flotation: of phosphate type (sodium tripolyphosphate, mono and diethers of alkylphosphpric acid) and sodium xanthate as collector for sulphides. The given set reagents provides for high effectiveness of flotation due to selective of collectors and presence of froth layer with high carrying ability. New flotation technology of recovering of baddeleyite from complex ore was developed and applied at the Kovdor Mining Plant, using AKER flotation machines.

Jan 1, 1995

By C. I. Garcia, G. Zhou, W. Gao, A. J. DeArdo

The development of X-100 and X-120 linepipe steels was investigated using a series of low-carbon Mo-Nb-B steels. The laboratory steels were vacuum melted and processed using advanced thermomechanical processing (TMP) philosophies. Prior to the laboratory hot-rolling experiments, the grain coarsening temperature, the conventional T95 and T5 start-stop recrystallization temperatures and the transformation behavior of y were studied using a computer-controlled high temperature deformation MTS-458 and a Theta-IV High Speed dilatometer systems. The results from these experiments provided the guidelines for the design of the laboratory hot-rolling TMP processing experiments. The mechanical properties of the experimental steels showed yield strengths in the range 700-850 MPa and CVN impact properties of over 80 J at -20°C. The best balance of mechanical properties was obtained by using CCR+DQ+Tempering treatments. The major microstructural features responsible for the observed mechanical properties in order of importance were: a) substructural refinement associated with lower bainite, b) dislocation strengthening, c) fine recrystallized ferrite, and d) small amounts of retained austenite. Fine Nb(C,N) precipitates formed in ferrite were observed, however their contribution to the strength was minimum. Most of the Nb(C,N) precipitation took place in austenite. This precipitation was used to exert microstructural control of austenite during hot rolling. The physical metallurgy and optimum TMP to achieve the mechanical properties are detailed in this paper.

Jan 1, 2005

By Charles H. Greene

This paper will describe briefly the steps taken in the development of a Central Florida phosphate ore deposit from acquisition to mining. Further, the design and early operation of the mining and beneficiation facilities will be depicted. During the 1950's, with confidence in the continually increasing requirement for phosphate fertilizer materials essential for producing food, I'. R. Grace & Cc acquired the Hookers Prairie tract containing approximately 45 million metric tons o. (50 million short ton~ of potential phosphate rock product. In 1973, at a point when the Grace captive need for rock was being greatly enlarged by a planned doubling of its Bartow phosphate chemicals plant capacity, the decision was made to expand existing phosphate rock production by building a new mine and plant. The initial annual capacity was to be 2.3 million tons (2.5 million st); however, subsequent investigation pointed to a higher than estimated dragline operating factor 'and the forecast of annual capacity was set at 2.5 million tons (2.8 million st).

Jan 1, 1977

By R. L. Peyton

Risk analysis is used extensively in many engineering applications. Although its use in the field of dam safety has been limited in practice, it has received considerable attention in recent years in the dam safety literature. Thus far, it has been shown that risk analysis in the evaluation of existing dams has the potential for providing a more rational basis for decision- making because of its focus on the direct issues--likelihood of failure, likelihood of loss of life, and risk cost of damages. It provides for a logical balance between the risk a dam imposes and the degree to which rehabilitation is required, compared to traditional evaluations based on somewhat arbitrarily chosen design events applied to large classes of dams. Dam owners could benefit by optimizing the cost of remedial measures. Downstream landowners could benefit by minimizing the likelihood of flood damages. However, it is also clear that significant technical and policy issues remain to be resolved before risk analysis in dam safety is accepted and routinely implemented in engineering practice. An obvious and important potential application of risk analysis is its use by the state regulatory agency as an in-house evaluation tool, or even as part of regulatory policy, in the implementation of its state dam safety program. Adoption of such a policy would have an important impact on the mining industry. .Although no state dam safety programs are known by the writers to have officially incorporated risk analysis into their regulations, there appears to be considerable interest in the concept. In recent surveys 47 states agreed that the development and promotion of a risk assessment methodology for state dam safety programs should be encouraged (Tschantz, 1983; Tschantz, 1984). The issue has also received important attention within the Association of State Dam Safety Officials (1986). One state-Illinois-proposed regulations during 1986 to allow risk analysis to justify lower spillway requirements for existing dams (Illinois Department of Transportation, 1986). At the Federal level, the National Research Council has found risk analysis especially appropriate for assessing dam safety at high-hazard dams (National Research Council, 19851, the Bureau of Reclamation has published guidelines for incorporating risk analysis into their dam safety grogram (U.S. Department of the Interior, 1986), and the Federal Emergency Management Agency has recently sponsored workshops and supported research related to risk analysis in dam safety (Federal Emergency Management Agency, 1985a ; Federal Emergency Management Agency, 1985b; - - McCann, et. al., 1985a, 1985b).

Jan 1, 1986

By R R LARGE

In the past decade mineral deposit models have become an important tool for the exploration geoscientist. By combining genetic theories on the formation of particular deposit styles, with geological, geochemical and geophysical criteria relevant to ore location, it has been possible to more effectively focus exploration effort to the regions and local targets which have the best chance of success. However, such models have their limitations, and must be carefully and critically applied and continually updated as new technical and research information becomes available.

Jan 1, 1992

By Seiji Mizutani, Hirofumi Taguchi, Makoto Yoshida, Hidenori Takahashi, Naotoshi Shinkawa, Kazuo Konishi, Yoshiyuki Morikawa, Masaya Kawata

"The lattice-shaped cement treatment method has been used to improve the seismic performance of liquefied sandy soil in Japan. The efficacy of the method has been confirmed by the huge earthquake in Japan. In the present study, a new method to improve sandy ground by using the lattice-shaped cement treatment method is proposed as a liquefaction countermeasure. It is the floating-type and lattice-shaped cement treatment method, where cement treated soil is not fixed to an un-liquefiable stratum. In this method, a fixed-type structure such as treated soil should be formed at the side of the floating-type treated soil to reduce its lateral displacement. In the study, one-dimensional dynamic response analyses were firstly conducted to confirm the mechanism of the new method. Secondly, a series of centrifuge model tests were performed to demonstrate the effect in a proto-type scale's stress condition. The analyses and model tests confirmed the effect of liquefaction countermeasure of the new method.INTRODUCTIONLiquefaction induced by an earthquake generates sand boiling and ground settlement. Other problems have also been reported, including a decrease in bearing capacity and an increase in the horizontal earth pressure against retaining walls. To prevent these problems caused by liquefaction of the ground, various countermeasures have been proposed, such as cement deep mixing and high-pressure jet mixing methods. These methods have the big advantage of being applicable to ground that contains soil with a fine-grain fraction. Furthermore, the unnecessary displacement caused by the construction can be reduced. In Japan, a lattice-shaped cement-treatment method has frequently been used at many construction sites to prevent liquefaction, where cement-treated piles are intersected to form a lattice, as shown in Fig. 1. The lattice-shaped walls can reduce the shear stress generated by an earthquake, restricting the liquefaction at that location. However, the construction cost of the cement treatment is relatively high compared to other methods such as the sand compaction pile (SCP) method, and needs to be reduced. Therefore, decreasing the total volume of the cement treatment is necessary to reduce the construction cost."

Jan 1, 2015

By S. A. Bunk, E. C. Eccleston, J. J. Amsden

Fluidized bed technology has been widely applied to mineral and metallurgical processes. Over the years, modeling of fluidization technology has progressed to a level at which basic design parameters can usually be defined based on empirical correlations. In addition, scale-up considerations have become better understood, and significant advances have been made in the area of computer simulation. Despite these advances, fluidization is a complex phenomenon, and modeling tools remain limited in their ability to simultaneously model both fluidization and chemical process parameters. As a result, almost all mineral and metallurgical applications of fluidized bed technology require pilot testing prior commercial scale design. This paper outlines pilot plant testing requirements and process development considerations for development of low technical risk commercial designs.

Jan 1, 2011

By G. L. Simmons

Aqueous pressure oxidation at low temperature, although desirable from a process engineering and operations point of view, presents unique problems when temperatures approach 160°C (320°F). In developing the pressure oxidation process for the Lone Tree Mine, elemental sulfur formation and agglomeration with pyrite proved to be a problem. This paper discusses some of the unique features of the Lone Tree sulfide deposit and its amenability to low temperature oxidation. Problems encountered during pilot plant operation and their solutions are discussed.

Jan 1, 1993

By S. N. Gurulaxmi, Veerendra Singh

The abstract discusses the increasing consumption of manganese ores and the need to utilize low-grade ores and rejects. The study focuses on developing a low-cost process using a cupola furnace to recover manganese values from these resources. The process involves smelting ore blends to produce high MnO slag and pig iron. The study investigates various factors to improve iron reduction and separation from MnO-bearing slag. The results show that the process can produce slag with MnO > 35% and Fe(t) < 5% using low-grade Mn ores. The process also achieves Fe reduction between 50 and 70%. The cupola furnace offers advantages like low cost and ease of operation, making it suitable for processing low-grade ores and rejects to produce synthetic MnO-enriched products for various industries.

Apr 1, 2022

By T. McWaters

Miami Copper Company began a block-caving operation in 1911 using a gravity mill to separate copper minerals from the Pinal Schist host rock. The tailing was deposited by the upstream method using perimeter launders and spigot valves in six canyons adjacent to the mill until 1932. In 1928 the larger and more distant Solitude tailing pile was developed which by 1932 was receiving all tailing except for upsets. In 1925 Miami Copper converted its gravity mill to flotation which began to produce higher sulfide copper recoveries.

Jan 1, 1990

By Gábor Antal, József Bõhm, Barnabás Csõke

From the waste material of the production of aluminium foil aluminium pigment is produced for the paint industry by grinding it in white spirit. During grinding 1-2 % iron impurity gets into the product, weakening its quality, from the wear of the mill armour and the grinding bodies and from the contamination of the raw material. For deironing the product, a stage-operated electrically induced magnetic filter separator was developed and put into operation. The separator was sited in an explosive environment and therefore required a special design and safety system. The paper describes the results of the development work. the device that was developed, the safety system as well as the results of and experiences with the operation of the separator.

Jan 1, 1995

By V. Thangadurai

The critical problems in commercialization of the present solid oxide fuel cells (SOFCs) and useful electrical and physical properties of IT-SOFCs electrolytes are discussed briefly. The conductivity behavior of the perovskite-type and perovskite-related structure metal oxides are summarized. Perovskite-type La0.9Sr0.10ao.8Mgo.203_8 (LSGM) exhibits high ionic conductivity of 0.1 S/cm at 800 °C. In order to improve the electrical conductivity of LSGM and the In analogue of LSGM, substitutions have been made at the A-and B-sites. Substitution of trivalent La3+ by isovalent Pr3+ in LSGM and La09Sro ilno.sMgo.202.85 (LSIM), yield new mixed conductors. Among the investigated compounds in the present study, La0APro.4Sro.21no sMgo.2028 exhibits the highest total electrical conductivity of 3.2 x 10-5 S/cm at 200 °C in air with the lowest activation energy of 0.44 eV (200-700 °C). LSIM and Pr-substituted LSGM and LSIM perovskites show p-type electronic conductivity in the oxygen partial pressure range 10-5 ? 0.21 atm at 750 °C. The perovskite-type solid solution SrSn1-xFex03 exhibits compositionally driven phase transitions. For example, compound of the composition x = 0 to 0.3 crystallizes in an orthorhombic GdFeO3-like perovskite structure, where as that of x = 0.4-0.9 crystallizes in simple cubic SrTiO3-like, and that of x = 1 in orthorhombic structure. The electrical conductivity of SrSn1_xFex03 increases with the increasing Fe content and reaches a value of about 10-1 S/cm at 25 °C in air for x = 1. Compounds with low Fe content exhibit both ionic and electronic conductivity, while the higher Fe content 0.5) perovskites are electronic conductors over a wide range of oxygen partial pressure of 10-22? 0.21 atm at 750 °C.

Jan 1, 2005

By Lan Li, Izaak Williamson

"The efficient separation and storage of CO2 from power plant flue gases can reduce the amount of CO2 released into the atmosphere and mitigate global warming. Potential candidates for industrial applications are solid sorbent materials. Crucial factors to control the efficiency of porous sorbent materials include the framework and pore structure, and the chemical and physical reactivity of CO2 within the pores. Computational modeling approaches, based on density functional theory (DFT) and van der Waals-DFT, have been applied to nanoporous solid – manganese dioxide a-MnO2. We found that the types and charges of cations as dopants in the a-MnO2 and the concentration of CO2 influence the structural features of a-MnO2, which control its CO2 selectivity performance within the flue gases.IntroductionCarbon capture and storage is a technique to separate large quantities of CO2 from power plant flue gases before being released into the atmosphere. Porous solids are a potential candidate as sorbents to “trap” CO2 through chemical or physical adsorption on their porous surfaces[1]. Such separation efficiency is determined by the size and shape of its pores and by the interaction between the porous surface and the gas adsorbates. The incorporation of cations into the pore can act as a means of structural support and alter the pore diameter to be comparable to the kinetic diameter of the gas adsorbate, such as CO2.A porous solid of particular interest for CCS is manganese dioxide a-MnO2, an octahedral molecular sieve (OMS) composed of edge-sharing MnO6 octahedra that are linked into a nanoporous framework[2]. The framework consists of (1×1) and (2×2) tunnels, referred to as OMS-2. Due to the larger tunnel size, cations and gas adsorbates prefer to reside along the (2×2) tunnel axis of the OMS-2. As seen in Figure 1, a potassium cation K+ is located in the (2×2) tunnel, known as cryptomelane-type MnO2. Its pore diameter of ~ 4.6 Å gives it a good CO2 selectivity performance, because the diameter is comparable to the kinetic diameter of 3.3 Å for CO2[3]. Alternatively, replacing potassium K+ with other cations, e.g. barium Ba2+, sodium Na+ or lithium Li+, in the OMS-2 tunnel is of great research interest, due to the effects of their concentrations, types and charges on the CO2 selectivity efficiency and sorption hysteresis phenomenon[2,4]."

Jan 1, 2014

By H. Mischo, F. Daniela, L. Schaarschmidt, I. Paschke

In order to safely store radioactive waste long-term, HAW repositories in saliferous formations have to be backfilled. The main purpose of those backfill operations is the restoration of the geological barrier function of the containment area. For best possible results the used material should be of a comparable composition or characteristic for the host rock formation. Additionally, the material should show a high density after completion of the backfilling process as well as a low permeability. A major aspect to consider in these processes is the minimization of the gap of the backfill body to the roof of the drift. To fulfil those requirements, a micro-structure stabilized crushed salt backfill material has been developed as part of the GESAV-I-project. Due to the material composition of this so-called GESAV-material, salt mineralcrystallization processes start after emplacing it, a process that leads to the polyhalite formation. With the crystallization of polyhalit, the halite grains are bridged, which in return stabilizes the matrix of the backfill. The GESAV-II-project continued successfully what GESAV-I started and determined an ideal backfill method in order to build the backfill bodies composed of GESAV-material. Due to the compaction of the material during emplacement by vibration, high in-situ densities, low permeabilities and a backfill factor close to 1 was able to be reached. In the following SAVER project this journey of practical test underground will be continued.

Mar 2, 2022

By William Kendall

INTRODUCTION Stillwater Mining Company, with its two underground, hard rock mines in South Central Montana, is the largest primary producer of palladium and platinum in the Western Hemisphere. Platinum Group Metals (PGMs) are mined from a specific zone within the Stillwater Complex, a layered mafic/ultramafic igneous intrusion, named as the J-M Reef. Over much of the J-M Reef, the economically minable, mineralized horizon is contained at typical horizontal widths of 6.5 ft to 8 ft wide. This feature of narrow mining widths has made it challenging to safely and effectively mine these areas of the J-M Reef using mechanized cut and fill and sublevel sill development mining methods. Mechanization of most or all of the steps of the mining process is important to Stillwater in the continuous pursuit of high standards in safety and health. Mechanized bolting within the J-M Reef ore production headings is an important piece of reaching these objectives. In general, metal/non-metal mining requires varied mining techniques, as compared to more traditional bedded mineral/resource deposits. Narrow vein mining is a selective mining technique that generates a minimal amount of waste material while obtaining the more valuable ore deposits. Drilling and bolting in narrow vein mining has traditionally been performed with air-powered, hand-held ?jackleg? equipment because mechanized equipment is, typically, too large for the selective narrow vein techniques. In addition, traditional hand-held pneumatic equipment provides significant flexibility for small-opening, narrow-vein developments, reducing waste rock handling and improving ore recovery management. The hand-held equipment is also relatively inexpensive to purchase. Due to its simplicity, it is also relatively easy to train operators to use hand-held equipment. Hand-held equipment has been routinely used to safely install ground support and to develop production faces in hard rock mines for many years. Although it is effective, the hand-held equipment requires operator exposure to certain inherent hazardous conditions in the active face/development mine areas. These include falling rock, tripping hazards, bending/twisting/lifting hazards, high noise levels, and chemical fumes from the hammer exhaust. Based on health and safety statistics from the Stillwater mines, operation of the rotary-percussive hand-held equipment adversely affects the long-term health of the operator?continual jackleg operation frequently results in long term damage to hearing, shoulders, arm and wrist joints, and back injuries. This reduces the quality of life for the operator and also results in higher personnel turnover rates for the mining company.

Jan 1, 2014

By Ian Sherrell, Christian Cardoso, Henri Vepsäläinen, Guillermo Bermudez

Performance of mixing mechanisms in flotation cells is paramount, as inefficiencies can lead to financial losses through valuable minerals lost to tailings. Technological advancements have been implemented in flotation cells to optimize performance, but regardless of the efficacy of these developments, room for improvement may persist. Since its launch in 2005, FloatForce® has set a high industry standard for flotation mixing mechanisms. However, current mining trends call for sustainability-driven developments while improving metallurgical performance. Metso has recently introduced FloatForce®+, the latest iteration of FloatForce, developed through extensive laboratory, pilot, and industrial testing, aligning with mining sustainability trends. It has been designed to maximize recovery, reduce power draw and optimize manufacturing materials. This development stems from a redesigned rotor profile paired with a harmonizing stator configuration. This paper presents the development journey of Metso’s latest patented flotation mixing mechanism, an advancement to improve metallurgical performance at a high sustainable standard in flotation cells. The theory, CFD modeling and test work are discussed in detail.

Feb 1, 2025