Search Documents

By Achille Balossi Restelli, Elena Rovetto, Andrea Pettinaroli

"The Station “C13” of Warsaw Underground Line II, with tunnel crown 10m below the water table, required the excavation of three connection tunnels, underpassing a six-lane in service road tunnel, working from two lateral shafts. After the collapse occurred while digging the first tunnel, the use of artificial ground freezing was chosen to ensure the excavation under safe conditions. A complex freezing pipe geometry and excavation sequencing was necessary because of the interferences of the overlying road tunnel diaphragm wall foundations, shaft internal structures and previous grouting activities. A combined freezing method was used: nitrogen for freezing the tunnel arches, brine for freezing the intermediate wall and for maintenance stages. Sandy and silty sandy layers were frozen around the crowns and sides. No treatment was necessary for the inverts, lying in clay. A monitoring system of ground temperatures and structure movements allowed for successful completion of work in 8 months. INTRODUCTION The C13 Station of the Warsaw Underground-Line II is located on the West bank of the Vistula River. It consists of two shafts and three connecting tunnels, passing under the Wislostrada (WS) Road tunnel. According to the initial geotechnical investigation, tunnels should have been excavated in high-plasticity clay, but during the first borings non cohesive soil was encountered. Additional investigations were performed on both shafts and a more detailed stratigraphy was reconstructed (Lombardi et al. 2015). Layers of fine sand, sandy silt and sandy silty clay were present along the tunnels crown arches and in the North East tunnel they extended down to the centre line (-13.735m above the Vistula River medium level). Based on the new stratigraphy, it was decided to stabilize the crown and control the groundwater inflow from the face with jet-grouting columns extending the treatment down to the clayey soil, but a collapse occurred in the North West tunnel with soil and water inflow inside the shaft."

Jan 1, 2016

By K Verbeken, D Seveno, A Maslov, I Bellemans

Recycling and decarbonisation current metallurgical processes is key for our planet’s future and in both cases, digital twinning will play an important role. However, the various modelling techniques being used for digital twinning require a lot of input values on variables such as viscosities, diffusion coefficients and surface energies that need to be known as a function of temperature, atmosphere and composition, but which are not widely available, such as in databases, for molten slag phases. The need for more accurate data on physical slag properties is clear and will be extremely relevant for making more realistic and quantitative simulations. Some of these properties are difficult to determine, which is inherent to the very high pyrometallurgical temperatures. Therefore, this work focuses on some aspects related to determining electrical conductivities, viscosities and surface tensions of slags via a combined experimental-modelling method. Besides experimental work, molecular dynamics (MD) simulations can be used to investigate oxidic slag physical properties. With MD simulations, one can follow the time evolution of a system (consisting of atoms or molecules) by integrating Newton’s equation of motion. The input for an MD simulation mainly consists of a force field as well as initial positions, velocities and mass of each atom. The determination of the transport properties in existing literature of MD simulations in oxidic systems, is typically based on incorrect assumptions. For example, to determine the ionic conductivity, the frequently-used Einstein-Stokes equation fails to take into account all ionic types and neglects correlated motion. Furthermore, the viscosity determination via the Einstein-Stokes formula also assumes independent motion of the different ions. This paper gives a brief overview of the opportunities and challenges related to the use of MD simulations for oxidic slag systems.

Jun 19, 2024

By Rumen Markov, Lubomir Kuzev

"The treatment technologies for municipal solid waste (MSW) are effective mainly for components sized over 40 – 50 mm. This fraction is separated by screening in the beginning of the process. Usually the undersized product is deposited without additional treatment. Its quantity is variable from several up to 30 – 40 % of the total MSW. Both oversized and undersized fractions are formed by all types of primary matter. Adapted technologies from mineral processing will provide a suitable technology for treatment of MSW under 40 – 50 mm. The MSW content depends on the geographical location, the degree of urbanization and other factors. The methods can be applied for separations of different components suitable for recycling or other utilization are: • Separation by density; • Separation in thin liquid layer; • Selective grinding and screening; • Flotation, etc. Introduction Municipal solid waste (MSW) represents an integral part of public urbanization. However, there are some drawbacks stemming from MSW, in regard to its collection, transport and elimination. Different approaches exits worldwide for tackling the problems arising from MSW. For a short period of time, the attitude towards MSW has evolved in several levels, each further level being characterized by higher percentage of utilization of MSW components. Thus, the bottom line has been shifted from safety storage towards processing that includes recycling and maximal utilization of MSW components. Technologic processes applied for treatment of MSW have a common feature – that the fine components, having sizes under 20 mm, 30 mm, 40 mm, or 50 mm are excluded from treatment process trough screening, and in most cases diverted without any additional treatment to preliminary prepared storage sites. MSW in Sofia – current situation The amount of MSW collected daily in Sofia as around 1000 t/24 h. It is stored or baled. Baling is a spare alternative of storage, since baling insures only temporal keeping of MSW, till the building of suitable storage site where the bales will be transported and buried. The morphologic composition of MSW in Sofia has been determined several times at different time intervals, from some Bulgarian organizations as well as from the Japanese organization JICA. So far, however, there is still a lack of enough systematical and comprehensive study. Generalized results from the studies on the MSW components, as well as some important parameters are given in Table 1."

Jan 1, 2008

By H. J. van Antwerpen

AngloGold Ashanti operates the world`s deepest mine, Mponeng gold mine, in South Africa. A vast refrigeration and ventilation system provides acceptable working conditions 3800m below surface at 60°C rock temperature. In such a system, optimisation and assessment of modifications becomes very difficult. With that in mind, a research project was launched to determine whether recently developed system simulation technology can be applied to a mine as vast and complex as Mponeng. Using the techniques and methods as implemented in FLOWNEX software, it was indeed proven to be possible to do a mine-wide combined simulation of compressed air flow, ventilation air psychrometry and refrigeration water systems. Interactions between the various streams included heat transfer, pressure drop, evaporation and condensation. The simulation model was used in a parametric study to test various water flow and temperature operating points for the refrigeration system. It was found that, given current limitations, the mine refrigeration system is running fairly close to optimal but with some opportunities for improvement. The simulation model also provided useful insight for future changes or extensions to the system.

Feb 23, 2014

By Jean-Pierre Côté, Alexandre Noiseux

"Hatch and ArcelorMittal Mines Canada have combined their expertise to develop a dynamic model of the latter’s Iron Ore Pellet Plant in Quebec, Canada. This model was used to predict the benefits of different expansion projects, as well as asses the best implementation sequence.Two modelling tools were used: a discrete-event simulation software used to develop the dynamic model of the Pellet Plant and an in-house process simulator. The latter was based on operational data and known behavior of the process, and was calibrated with historical data gathered under different operating conditions.The results of the process simulator were used as input values for the dynamic model, which included all of the operation steps of the pelletizing process, from concentrate beneficiation to baking of the pellets. The model has been validated by assessing its capacity to represent adequately the operation of the plant during a 20-month operating period. It was able to reproduce the plant capacity within a precision of 1.2%.Simulated “what-if” scenarios allowed quantifying the production increase associated with the addition of new equipment such as ball mills or balling discs, implemented individually or in combination. Results revealed a potential 10% increase in the annual plant production by adding additional equipment in the two most limiting sectors of the plant, grinding and agglomeration. The simulation results made it possible to quantify the synergistic effect of two projects on plant throughput; the model showed that the combination of two projects resulted in a greater production increase than the sum of the same projects evaluated individually.Now that it has proven reliable, the simulation tool can readily be used by ArcelorMittal Mines Canada process engineers to perform simulations for equipment optimization, and to evaluate the impact of various operating parameters such as equipment availability and tonnage, product mix or concentrate quality. This work showed that a reliable model can be developed based on known parameters in combination with the proper integration of the process knowledge."

Jan 1, 2010

By Nural Kuyucak

Several thousand years ago, metallurgists discovered that by combining two relatively soft metals, copper and tin, they could make a new material, bronze, that was stronger than either metal separately. Bronze and other alloys show how different materials can be integrated to create something new and better. Today?s mining industry can likewise find benefit in an integrated approach to managing the external impacts it has through its waste materials and its use of water. Just as using bronze gave ancient nations an economic and military advantage, mining companies can gain competitive advantage through finding better ways to manage water and waste. Trends pushing this include: ? Environmental ? Regulations on water-taking and the quality of discharged water are becoming more stringent. Net zero discharge requirements are often imposed by regulators. Mining companies also come under pressure to manage environmental impacts of mine waste, including minimizing the area occupied by waste and seepage amount resulting from infiltration of water from a smaller surface area. ? Social ? Particularly in arid parts of the world, there are multiple possible uses for each gallon of water. Local residents do not want to see a reduction in supplies of water for agricultural, domestic, manufacturing and other purposes. They get suspicious about any potential impact of water being mixed with their water reservoirs if it comes from a mining site, even if it would be treated. Such suspicions may cause conflicts among the stake-holders and delays in project approval processes.

Jan 1, 2009

By K. W. Harris, K. A. Perry

Underground coal mines beneath Black Mountain in the Harlan County district of the Central Appalachian coalfields have an extensive history of bump events, which yields an elevated probability for significant injury or fatality to underground miners. According to Mark (2009), Harlan County has had the greatest concentration of deep-cover retreat mining in the United States. Combined with the extensive multiple seam mining history, room-and-pillar coal bumps have had a disproportionate impact on coal operations in this region. The Harlan seam, one of the principal, economically recoverable coalbeds exploited beneath Black Mountain, has a significant burst history that extends into modern times. A numerical investigation using the LaModel software of 17 bumps that occurred at the same mine in the Harlan seam was conducted and used to create a calibration methodology which serves as the quantitative basis for current and future numerical efforts in an adjacent mine exploiting the same reserve. In addition to this numerical study, a qualitative assessment of the geologic factors that are believed to contribute to the bump potential was completed. Combined with stability prediction using the numerical basis, these geologic factors will be used for recognition of high bump potential areas with the goal of reducing the potential for future bumps, helping to ensure the highest level of safety and productivity for underground personnel.

Jan 1, 2016

By Karina Forster

Open stope design depends on the ore body geometry, loading conditions and rock mass properties to estimate stope dilution and ground support requirements. Rock mass conditions for design primarily rely upon estimates of well established rock classification systems. Many sources of data exist for obtaining estimates for these rock mass classification values which include core logging, geotechnical mapping, geological mapping as well as linking one classification system to another through the use of empirically derived equations. The extent of mapping coverage can also vary significantly based on the data collection technique. This paper proposes an approach where individual components of rock mass classification systems are collected by the different available data collection techniques. Data from different rock types are also considered separately based on their alteration characteristics and general observation products. Data from the Cameco Corporation Eagle Point Mine is presented and an approach is outlined for obtaining average representative classification values for stope hanging wall characterization. The effectiveness of this approach is demonstrated through the analysis of a data base of hanging wall dilution information.

Jun 1, 2012

By E. T. de Groot, D. L. Verhelst

With the successful start-up of Cominco's new KIVCET smelter, the final key component is now in place for Trail Operations to operate efficiently as a modern integrated zinc-lead facility. Unique metallurgical, operational, planning and management issues apply to this operation. Along with presenting the current flowsheet for Trail Operations, this paper discusses issues such as the impact of recycles, operational re-stabilization following significant process changes, plant operation with just-in-time inventories, real-time process optimization, and management philosophy.

Jan 1, 2000

In their excellent paper, Milev and Spottiswoode have provided quantitative and definitive descriptions of an important phenomenon that hitherto has been largely the subject of conjecture. They convincingly show that ?site-response? can amplify the strong ground motions on the rock-wall of a stressed tunnel by a factor of 10 to 12 compared with the PPV in the solid rock mass (at the same distance from source). This knowledge gives us a firm foundation from which to begin to build an understanding of the mechanism of damage resulting from a rock burst. Regrettably this understanding is still far from adequate, in my opinion. The authors of this paper, however, have made some statements that are too reassuring and which tend to reinforce the sense of complacency that prevails among many members of the rock engineering community on the deep gold mines.

Jan 1, 2006

By Ground Improvement Committee

The evaluation of earthquake-induced liquefaction has become a routine part of geotechnical engineering design. For a given project, if an analysis identifies a potential for liquefaction and the consequences of liquefaction are deemed unacceptable, then some form of hazard mitigation is required. Mitigation efforts may consist of removing the liquefiable soils, bypassing the liquefiable soils with deep foundations, structurally accommodating the deformations or strength loss caused by liquefaction, or preventing the onset of liquefaction through ground improvement. The fundamental ground improvement mechanisms for liquefaction mitigation include densification, drainage, and reinforcement. When evaluating, recommending and specifying various ground improvement methods for liquefaction mitigation, practitioners should understand the fundamental mechanics involved and applicability and limitations of the various methods. The DFI Ground Improvement Committee offers a review of the fundamental mechanics and commentary on the applicability and limitations of each method to provide clarity and guidance on the issues related to ground improvement for liquefaction mitigation.

Aug 1, 2013

"Canada Centre for Mineral and Energy Technology (CANMET)Natural Resources CanadaMining and Mineral Sciences LaboratoriesA. Address and Contact Information555 Booth StreetOttawa, Ontario, Canada, KIA OGlWebsite: http://www.nrcan.gc.ca/Contact: Philippe Dauphin, Manager, Business DevelopmentTel.: (613) 947-0798Fax: (613) 947-0984E-mail: pdauphin@NRCan.gc.caB. Type and Size of FacilityScope of facilitiesCrushing from minus 4 in. to 10 mesh; grinding - rod, ball, vibration, SAG and impact mills; classification- screening, cycloning, mechanical, hydraulic and dry centrifugal classifiers; froth flotation - automated, column, and frothless flotation; gravity separation- wet and dry; magnetic separation - high gradient, high and low intensity, wet and dry; electrostatic separation; heavy-media separation; calcining; cyanidation; thickening; filtration; drying - fluid bed and freeze drying; pelletizing; microwave.SpecialtiesMineral beneficiation research and development; flotation of sulphides - flowsheet improvement, selectivity, reagent selection; novel flotation techniques; analysis of thiosalts formation; use of mineral processing techniques for recycling.Specialized equipmentHigh gradient magnetic separation, Denver XRF on-stream analyzer, automated flotation cell.Complementary support servicesElectron microprobe; SEM; STEM; X-ray diffraction; particle size analyzer; mineralogical and analytical chemistry services; physical chemistry; hydrometallurgy; pyrometallurgy; engineering and economic evaluation; mechanical shops; technical information services and library integrated with the National Library System of the National Research Council."

Jan 1, 2000

By R. J. McClincy

The potential techniques for the direct smelting of copper sulfide concentrates to blister copper were evaluated from the standpoint of commercial application. Many existing smelters are adaptable to direct smelting practice but only with improved control of metallurgical performance. Modified and innovative procedures for slag cleaning and metal refining, prerequisites to direct smelting, are presented and discussed. The ability to smelt directly to blister copper using existing equipment and eliminating the need to convert matte offers ,significant advantages to traditional smelting practice from the viewpoint of cost, 'S02 control, and process simplicity.

Jan 1, 1983

By D. J. Cassidy

This document discusses commercial strategies and applications of specialty processing plants for the recycling of nickel, copper, zinc and cobalt bearing by-products. For this discussion, I will focus on materials originating from the metal plating, electronic circuit board· and chemical industries. The review of select processes and the required service, sourcing, material handling, processing and marketing strategies necessary for a successful recycling program are highlighted. Materials discussed in this summary include filtercakes, filters, dusts, spent catalysts, spent solutions and solids. Both pyrometallurgical and hyrometallurgical applications to these materials are addressed. A comparison of targeted finished markets, including smelter feeds and value added products are also reviewed.

Jan 1, 2000

By A C. Robertson

World urban expansion puts constraints on the available land surface area of our major cities both for accommodating people as well as providing infrastructure and services whilst at the same time attempting to preserve the remaining natural environment. Whilst consideration is often given to underground planning for private and public transport infrastructure, the author is of the opinion that the current lack of underground planning of our cities that are suitable for underground development will have major long implications when finally the need for underground space planning is critical and ultimately recognised. This paper identifies the need for our city planners to integrate surface planning and underground planning as a ‘total planning solution’ where the city plan incorporates the elements of underground space planning as identified in this paper. Investigations by the author reveal that there are very few cities in the world that actually incorporate underground space planning in their city plans. The author uses the City of Brisbane as a case study for the potential introduction of underground space planning as part of the city plan. Despite efforts by the author to include the planning concept of underground commercial development in the latest Brisbane City Plan 2014 as well as four underground space workshops in Brisbane over the past 20 year through the Australasian Tunnelling Society (ATS), underground space planning for the City of Brisbane, apart from infrastructure projects, is not considered of significance to the City of Brisbane.CITATION:Robertson, A C, 2014. Commercial underground space – planned development for the future, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 513–518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Gil Bourcier

A process has been developed for detoxifying spent potliner (SPL) in which the SPL is blended with limestone and an anti-agglomeration agent and thermally treated in a rotary kiln. The process has been proven and a commercial plant is in operation at Gum Springs, Arkansas. The treated by-product material has been delisted by the U.S. EPA and is now a potential raw material for many commercial applications. Finding uses for a non-hazardous material has many advantages over finding uses for a hazardous material like SPL. Complete usage of the by-product will complete the life cycle and eliminate any landfilling of non-hazardous SPL by-products or residues. Being non-hazardous and containing compounds used in the ceramic and numerous other industries assures many potential uses for the spent potliner by-product.

Jan 1, 1994

By Kathryn C. Sole

A novel solvent-extraction process for the refining of gold was recently commercialised, with the commissioning in May 1997 of a 24 t a-' refinery at Harmony Gold Mine in Virginia, South Africa. The MinataurTM Process (Mintek Alternative Technology for Au Refining) uses solvent-extraction technology to produce gold of 99.99% purity from the cathode sludge arising from a conventional carbon-in-pulp / electrowinning circuit. Implementation of this process introduces significant cost benefits compared with the conventional dore smelting / toll-refining route previously followed. This paper outlines the process, presents selected operating results obtained during the first few months of operation, and provides some details of the associated techno-economic advantages.

Jan 1, 1998

By N. R. Hasenmueller, V. Rajaram, R. K. Leininger, D. D. Carr

The content of the paper by V. Rajaram does not fulfill the expectations of the title. But Rajaram submitted the article in October 1983, and he could not have foreseen the numerous developments that would occur before his paper was published more than two years later. Nevertheless, Rajaram failed to mention the interest in oil shale development in southern Indiana beginning in late 1979 and continuing through the present as a result of special financial encouragement of three oil shale projects in May and August 1984 by the Indiana Energy Development Board and the Indiana Corp. for Science and Technology. A session at the 1985 Eastern Oil Shale Symposium in Lexington, KY, Nov. 18-20, 1985, gave the current status of oil shale developments in the eastern United States. Speakers at this session reported on the three Indiana projects. First, Gary D. Aho, Cliffs Engineering Inc., spoke on a feasibility study by Cliffs Engineering and Allis Chalmers for a site-specific pilot plant using the Allis Chalmers process. The plant site is in Clark County, IN, on property of the Midwest Energy Resources Co. The project is funded by $240,908 each from the Indiana Energy Development Board/Corp, for Science and Technology (EDB/CST) and the US Department of Energy (DOE) and $120,454 from the corporate sponsors (total $602,270). Completion is scheduled for mid-1986. Next, Edwin M. Piper, Stone and Webster Engineering Corp., discussed the American Syn-Crude/Indiana Oil Shale Project. This effort followed the completion of two smaller projects funded by the Indiana EDB/ CST: "Testing of Indiana Oil Shale in a Petrosix Pilot Plant" (total funding by EDB/CST at $50,000) and "Assessment of the Petrosix Process for an Indiana Shale Oil Plant" (total funding by EDB/CST at $100,000). The status at the time of the report at the Oil Shale Symposium was that a request for an extension of time for securing nonfederal support had been submitted to the US Synfuels Corp. The proposal included building an 11-m (36-ft) diam retort in south-eastern Indiana to process the New Albany Shale and to produce 366 m3 (2300 bbl) of shale oil per day by the PETROSIX process. The Indiana EDB/CST had contracted with Stone and Webster at $401,100 from EDB/CST and $245,835 from Stone and Webster for activities to advance the project in the negotiations with Synfuels Corp. At the time of the report, this project was the only eastern oil shale proposal that was still on the agenda of the Synfuels Corp. As a result of Congressional action in late December 1985, federal support from the Synfuels Corp. is no longer possible. Finally, Victor H. Carr, Eastern Shale Research Corp., described his firm's project, which is jointly supported by DOE ($227,749) and the Indiana EDB/ CST ($73,850) and is entitled "Feasibility Study to Determine Suitability of an In-Situ Process to Recover Hydrocarbons from Eastern Shale." An area in Scott County, IN, had been chosen, but not a specific 9 x 15-m (30 x 50-ft) site. One burn of a small in situ retort is contemplated as part of the project. Besides these three projects, several reports on shale research were presented. Joseph Damukaitis, American Syn-Crude Corp., reported that a pilot plant using the hydrogenation-extraction (H-E) process (described at the 1984 Eastern Oil Shale Symposium) was 94% built and would go through shakedown with oil shale but would then shift mechanical devices to process coal mine waste. Current status of research on the HYTORT process was then presented by Raymond C. Rex, Jr. Oil shale beneficiation research at the University of Alabama/Minerals Research Institute was reported by R. Bruce Tippin. Scott D. Carter discussed continued research on fluidized-bed retorting of shale at the Kentucky Center for Energy Research Laboratory. Carl E. Roosmagi of DOE, Morgantown, reported on the oil shale research at the Morgantown Energy Technology Center (METC) laboratory. Henry J. Gomberg, Ann Arbor Nuclear Inc., discussed "Radiation Combined with Donor Solvents for Extraction and Up-Grading of Kerogen." Aurora M. Rubel and coauthor Eileen Davis presented results of research at the Kentucky Center for Energy Research Laboratory under the title "The Effect of Shale Particle Size on the Products from the Bench Scale Fixed Bed Steam Pyrolysis of Kentucky Sunbury Shale." Lastly, Maria Rockwell, Technical University of Nova Scotia, presented "Processing and Up-Grading of Low Grade Nova Scotia Oil Shale for Potential Use." A review of shale oil prospects by Gerald Parkinson in Chemical Engineering for Feb. 3, 1986, covers both western and eastern projects and includes a report that the US DOE is funding a few relatively small projects; most of the fiscal 1986 budget of $12 million for shale oil is for fundamental research. Projects include a $3.2 million three-year contract with Hycrude Corp. (Chicago) for development of the HYTORT process and a $1.2 million three-year contract with the University of Alabama's Mineral Resources Institute on beneficiation of eastern oil shale by froth flotation. The report incorrectly states that current projects include a total investment of $466 million in a pair of 18-month technical and economic feasibility studies for proposed projects in southern Indiana. The correct figure is $468,657 [$240,908 for the Cliffs Engineering/

Jan 1, 1987

By Hemendra N. Kalia

Several attempts have been made in the past sixty or so years to commerciliaze the vast oil shale deposits of the United States of America. However, the industry has yet to become viable and economic. To date, it has not been possible to produce oil from the oil shales at a competitive price when compared to the oil produced from oilfields by conventional methods. However, the development work has been quite fruitful in furthering the art of thick bed mining and technology of in situ retorting. The in situ method has the potential of recovering oil from thick beds and the resource recovery potential is much greater than that from underground mining and surface retorting. In situ methods require that the shales/ marlstones be fragmented ' in place to induce adequate porosity and permeability to allow in situ' heating of the fragmented shales. This can be accomplished by using explosives. However, it has been found that the existing blasting systems, though very efficient, are somewhat lacking. The explosive become insensitive when shot in multiple vertical decks. They can also become insensitive when spaced horizontally at close proximity to other charges. Also, since the blasting is done in a very limited free face, this limits the delay time that can be allowed between charges. Consequently it is not always possible to predict the performance of the blasting system on a routine basis. Furthermore, since it is not possible to undertake secodary blasting, it is imperative that the blast design function properly. Recent, successful retorting by Occidental Petroleum Company of retorts seven and eight suggests that some of these problems may have been overcome. This paper addresses some aspects of in situ retorting and problems those have impeded the development of a viable oil shale industry in the U.S.A.

Jan 1, 1983

By J. Stiksma, K. Buban, J. Oftsie, R. Kalanchey, S. Sadykov, E. McConaghy

The Kazakhmys zinc refinery in Balkhash, Kazakhstan, which employs the Dynatec Zinc Pressure Leach Process, officially launched autoclave operations on December 27, 2003. The Kazakhmys plant is the world's first greenfields zinc refinery based on Dynatec's two-stage pressure leach technology. Production of zinc was realized on February 9, 2004, when the first cathode was stripped. Currently the plant start-up is ongoing, with progression to two-stage zinc pressure leach operation and ramp-up to full design capacity continuing through 2004.

Jan 1, 2004