Search Documents

By Ben E. Adams

The Duval Corporation Sierrita copper and molybdenum mining complex is located approximately twenty-three miles south of Tucson, Arizona. The original open pit mine, Esperanza, was put into operation in 1958 and utilized one tailings dam until the Sierrita operation began in 1970, and a second pond was started. Both tailings operations continued to be operated separate and independently of each other until 1977, when the Esperanza Mill was temporarily shut down, and the Esperanza Tailings Dam was retired from service. Except for short periods of use, no new tailings were put on the surface. With the reactivation of the Esperanza Mill in 1979, the Esperanza tailings were combined with the Sierrita Mill tailings and put on the Sierrita Dam, leaving the Esperanza Dam in a retired state.

Jan 1, 1984

By W. K. Utt

This report discusses U.S. Bureau of Mines' research involving modem vehicle position determination techniques in surface mining. The applications would include haul trucks, power shovels, and drilling rigs. Accurate position determination of these vehicles in near real-time is expected to result in safer and more efficient mining operations. The requirements for a vehicle position monitoring and warning system were determined. After screening several concepts, the global positioning system (GPS) and a radar positioning system were selected for further evaluation. A state-of-the-art GPS receiver was taken to a surface mine to assess the feasibility of receiving the satellite signals. A state-of-the-art radar positioning system was evaluated with regard to accuracy.

Jan 1, 1995

Underground mines in Australia and worldwide are extending to greater depths. The effect of depth brings a number of challenges to mining engineers including geotechnical, ventilation, haulage and selection of mining method. The main effects of depth from a ventilation perspective are increased heat and humidity leading to reductions in productivity, occupational safety and health issues and the potential for fatalities. Numerous approaches have been undertaken over the years to mitigate against these effects. In this paper a review of various approaches to improving climatic conditions at a number of mine sites worldwide is undertaken. From these case studies it is argued that for mines at depth with the potential for a climate problem perhaps an alternative design philosophy to the established design philosophy should be utilised. In conclusion, the paper proposes some simple rules of thumb for use in mines with climate problems or the potential for climate problems.

Jan 1, 2008

THE following really forms the second part of, or a sequel to, a paper, " Ventilating Metalliferous Mines: a Method of Attack," read before the Broken Hill Branch of the Australasian Institute of Mining and Metallurgy in May, 1920. In that paper the writer advocated a consideration of the question of ventilation in metal mines from a different aspect to that 'which had hitherto prevailed locally. Various factors regarded as having an important bearing on the subject were set forth, together with the results of observations made during ventilation tests carried out at the mining department of the Zinc Corporation.During the subsequent discussion the question was raised of the possibility of any practical application of the method of attack described, and also whether the theoretical considerations mentioned were likely to be of any real utility to the mining engineer engaged in ventilation work in a metalliferous mine.

Jan 1, 1923

By Georgi N. Shoushoulov, Ventsislav D. Bozhilov

The mining conditions in the Meden Rid mine at levels below 1000 m from the Earth's surface are specific and rather severe. The rock temperature is about 40-45°C. The air humidity in the workings is approx. 80-90%. There is a limited capacity for additional fresh air supply. The air supply and distribution systems in the mine are very complicated. The airflow recirculation is due to the existing arrangement of the main fans. Certain accidental phenomena are difficult to predict. All these conditions create possibilities for heat and mass exchange between the rock and the air current thus hampering the control of the ventilation and air-conditioning in the mine workings. The changes in the temperature and humidity in certain characteristic places of the development and extraction workings are predicted. The refrigeration output required and the arrangement of the air coolers are also determined. A new ventilation and air- conditioning scherne has been developed. The new ventilation- cooling designs for levels between 1000-1200 m beneath the Earth's surface are based on the use of portable refrigerating machines having low water flowrate as well as heat-insulating and waterproof materials and methods for preliminary cooling of the orebody within the mining block.

Jan 1, 1997

Declines for both access and rock haulage are replacing shafts for mining relatively shallow deposits of down to 1000 m below surface. Where the orebody does not outcrop and where surface access may be restricted, it is often necessary to drive long dead end headings before a connection can be made back to surface and a ventilation circuit created. In hot tropical areas and where large diesel powered equipment is used for mining, heat may also be a problem at these relatively shallow depths. The normal design criteria based on statutory limits and good practice used to evaluate ventilation and cooling requirements in terms of air velocity, dust, gases, diesel exhaust dilution, re-entry after blasting and heat stress are described in this paper. These are then used to design and cost alternative auxiliary ventilation systems that include leakage based on general fan performance curves and typical duct systems. The implications of the current European Community recommendations regarding nitrous fumes are also briefly considered. The actual problem relates to a 2100 m long decline that may have to be extended to 3000 m long without a connection to surface or through ventilation and is located in a hot tropical area where the surface wet bulb temperatures may exceed 25¦C for more than a third of the summer period. Once the preliminary ventilation design is completed, the auxiliary ventilation system can be modelled and simulations undertaken that incorporate heat and moisture transfer routines with the objective of determining the cooling load and amount of refrigeration required. Cognisance is taken of cyclic diesel operations and the thermal flywheel effect of the surrounding rock on the wet and dry bulb temperatures resulting from these operations.A suitable modular cooling system located at the portal is described and optimised with capital and operating costs of both the ventilation and cooling systems provided.

Jan 1, 2005

By Mehmet Guney

This article is based on a detailed heat investigation conducted at the Rokana Division of Nchanga Consolidated Copper Mines Limited while both authors were employed in Zambia. Mindola Mine is one of the three underground mines comprising the Rokana Division on the Copperbelt of Zambia, producing about 270,000 tons of ore per month at 1.9% Cu and 0.14% Co. The total volume of air being circulated by means of five primary fan installations slightly exceeds 1,000 m3/sec at standard density. Sectional bulk cooling is practised where air cooling coils are installed at primary splits some considerable distance from the stoping operations. Total capacity of the refrigeration complex is 10,500 kw (3,500 R. tons), of which about 7,000 kw is available as effective cooling power after losses, but the heat removed from the coifs is about 3,500 kw with 61% over-all plant performance. An extension program is planned for a further five production levels with the re-deepening of a sub-vertical shaft. Thermal heat will become a major problem at increased depth associated with higher rock temperature, higher thermal conductivity of the rock groups encountered and fissure water flowing into working areas through the strata with increased rock temperature. This paper describes the ventilation and refrigeration practices in Mindola Mine, with special reference to future thermal heat problems. These are discussed with a view to mining at depth.

Jan 1, 1979

By Clifford S. Gibson

THESE troubled times suggest three reasons for maximum effort to control silicosis: (1) To keep to a minimum the ever-increasing burden occasioned by past deficiencies in this respect. (2) To effect the greatest production with maximum efficiency, which means at the least cost. (3) To preserve man-power in every way. Good control of the silicosis problem aids these aims. Inadequate control hampers all three. Insofar as our knowledge goes, silicosis in Ontario mines is caused by the inhalation of finely particulate quartz. It follows, therefore, that removal of dust containing this mineral automatically erases the cause. The achievement of this ideal is the aim of the mine operator. His best tool to this end is ventilation. This paper discusses mine ventilation from the viewpoint of dust control and it is hoped that in so doing there may result a better understanding of the part played by air in silicosis prevention. No attempt will be made to treat the subject fully. Instead, there will be presented certain salient aspects culled from field observations, the data in all cases referring to gold mines, unless mention to the contrary is made.

Jan 1, 1942

By Rainer Antretter

"THE CHALLENGE The 14km long, Arlbergtunnel, closed for public traffic during summer 2015, receiving a comprehensive and substantial renovation from 2015 to 2017. The main works discussed here, carried out during 2015, comprise 37 drill and blast SEM/NATM emergency escape tunnels from road level to the ventilation duct plenum have to be constructed as well as eight additional lay-by niches and three transformer tunnels. This presentation comprises the construction ventilation design, designed according to national regulations, suitable for 150 employees working 24/7 simultaneously at more than 40 single working sites lined up along the tunnel. The ventilation-system chosen was utilising two existing shafts for intake/discharge and a cross passage to surface, to handle a total fan power of 1.600kW. DESCRIPTION OF RENOVATION WORKS Linking Tyrol and Vorarlberg, two Federal States of Austria, the Arlbergtunnel is a single tube two-way road tunnel with vent duct plenum, constructed in the mid-1970s. According to latest EU legislation, additional escape exits have become obligatory. The existing seven cross passage links to the adjacent Arlberg Railway Tunnel, with average spacing of about 1.500m constructed in 2007, an additional upgrade to shorter escape spaces of approx. 400m was now required to comply with the updated legislation. Additional transformer tunnels, lay-by niches and small niches for emergency maintenance use, cleaning and other purposes, as well as a the installation of a new fire main in the invert, coupled with the simultaneous replacement of virtually the entire power and signaling cables, generated several dozen small and large single sites distributed along the 14km of tunnel.Purpose of the 37 walkable emergency escape tunnels is to reach the “upper deck” of the Arlbergtunnel, the vent duct plenum. These have an 180deg curve in plan, inclined at 10% and approx. 60m (65yd) long tunnels, excavated using drill and blast method starting from road level and working upwards to the level of an “intermediate soffit”, the vent duct plenum in the crown of the tunnel. The vent duct plenum is separated into a fresh air part and an exhaust air part, shown in Figure 1. The escape tunnels end with a pressure door in the fresh air section of the ventilation duct plenum. From there illuminated signs show the shortest escape route to the safe area between the road tunnel and the railway tunnel, as shown in Figure 2."

Jan 1, 2016

By D J. Brake

The underground metalliferous mining industry continues to change under the influence of many factors including, to name a few, new mining techniques and equipment, new approaches to risk management, more stringent safety and health standards, new employment practices and orebodies become deeper and often lower grade. In addition, the same technological revolution and plummeting cost of technology that has brought the GPS, smart phones and digital cameras to the general population is also working its way through the mining industry impacting on communications, automation and process control as well as introducing major efficiency and productivity dividends. However, not all factors are positive including, in particular, the issues of carbon costs and electrical power. This paper explores some of the trends affecting ventilation in hard rock mines, some of the existing and likely future challenges and some of the potential future solutions to these issues.CITATION:Brake, D J, 2013. Ventilation challenges facing the metalliferous sector, in Proceedings The Australian Mine Ventilation Conference , pp 3-12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By C M. Stewart

Lithium battery electric powered vehicles and machines (BEVs) continue to gain traction inunderground mining use, with predictions they will dominate the underground light and heavy vehicle fleets for some mines within the next decade. There are clear advantages for ventilation systems through reduced heat output and the elimination of harmful exhaust gases and diesel particulates. However, the risks and effects of BEV fire emergencies for underground personnel and ventilationsystems are still largely in the early stages of analysis and understanding. This paper conducts an industry review of a selection of lithium battery fire incidents and research.A research paper review on lihthium fire behaviour, intensity and toxicity will be analysed and comparisons made with equivalent diesel machinery fires for context. Guidelines for mine firemodelling parameters will be offered to assist in predicting the behaviour, heat and emissions from BEV fires, and recommendations and conclusions will be drawn on the specific hazards of lithium battery fires compared to conventional diesel powered machines.

Oct 12, 2022

By A Hatt

This paper presents a case study of characterisation work undertaken at a greenfield exploration project to provide engineering and OH&S inputs for the design of a ventilation system. The paper discusses how comprehensive early characterisation of the ambient surface and underground environment including aspects related to heat, dusts, strata gas, and geologic/mineralogical factors enables incorporation of the right ventilation and non-ventilation controls at a study level to mitigate the risks identified.

Oct 12, 2022

By Robert W. Miller

There are many problems faced by ventilation engineers in deep underground mining operations, not the least of which is controlling miner exposure to radon gas and its daughter products. Radon gas is commonly found in uranium mining operations, but may also be present in other deep metal mines. For example, tin mines in England, iron ore mines in Sweden, gold mines in South Africa, and molybdenum mines in the U. S. have potential radon exposures. This is because uranium and accompanying radium ore are ubiquitous to the earth's crust albeit at low levels. The fact that the activity represented by one WL can be caused by a relatively low concentration of radon gas increases the difficulty of control. Since the source of the radon gas is usually widespread throughout a mine, local exhaust ventilation is not a viable control schema. The technique used to control exposure is then dilution ventilation and, in fact, huge amounts of air must be moved in order to reduce potential exposures to an acceptable level. An interesting comparison can be made of ventilation rates in different types of mines. It is estimated in modern coal mines, which are generally acknowledged to have high rates of ventilation, that about eleven tons of air are moved for each ton of ore mined. A typical operating uranium mine may have ventilation flows of 14-15 tons per ton of ore mined. This provides an idea of the scope and importance of ventilation in modern mining operations where radon is a hazard. Further pressure is put on ventilation engineers by the steady downward trend in exposure limits set by national and international standard setting agencies. Much of this tendency toward lowered standards is based upon longitudinal mortality studies of miner populations. Another important factor is the limited number of experienced miners available in the labor pool. For optimum production, it is important to have as many experienced miners underground in each shift as possible. However, the average daily exposure in a U. S. mine must be less than .3 WL to permit the miner to work underground for a full year. The ventilation system then must provide enough uncontaminated air to maintain the WL below the .3 TTL level to maximize production efficiency and minimize personnel turnover and the problems associated with it. Ultimately, the goal of the ventilation engineer and health physicist is to protect the working miner from harmful exposures based upon currently acceptable standards. U. S. Federal regulations require that in uranium mines all active work sites must be monitored every two weeks if they measure above .1 WL. Areas that have .3 WL ratios or higher must be monitored on a weekly basis until five consecutive weekly samples show the level has dropped below .3 WL. Also, exposure records must be kept for all individuals exposed to levels exceeding .3 WL. These requirements provide a strong economic incentive to have a ventilation system that minimizes exposure of any personnel. A good ventilation system requires careful planning, operation and backup in order to fulfill its mission of providing adequate clean air. Its proper operation also requires coordination with production personnel so it can be adapted as new areas in the mine open up and old areas are sealed off. The ultimate indicator of ventilation efficiency to control radon daughter exposure is, of course, monitoring working levels. Historically, this has been done using the Kusnetz, Tsivoglou, and Rolle's methods, among others. These methods all require cumbersome equipment and tedious calculations to obtain the measurements that results in WL. More important, however, they require a significant time lag between sampling and counting, typically 40-90 minutes. This time lag is, in fact, what can cause significant economic losses due to unnecessary downtime as well as high WL exposures. In a typical mining situation, a sampling technician using the Kusnetz method takes a sample, moves to the next location and takes another sample and so on. Forty to ninety minutes after the first sample, the technician will stop, run the activity count on the filter and calculate the WL. The technician may be one-half mile away or several levels removed from where the first sample was taken when it is counted. If the WL ratio is high the technician must then backtrack to the sample position. There are then two options. If the sample area is a working stage, it can be shut down or a second sample can be taken. If the first alternative is chosen; i.e., shutdown and correction of the ventilation, then another sample must be taken, followed by a forty minute wait for results. If the ventilation adjustment didn't correct the problem, then the whole process must be repeated with a minimum of forty-five minutes per sample cycle when using the Kusnetz method. It has been estimated from operating uranium mines that the cost per hour for downtime on a production slope is about $1,50O/hour. The time lag between sampling and resultant data can be very costly. If the second alternative is chosen to verify the first reading, the miners may be unnecessarily exposed to high levels while waiting for the result. Clearly, such a sampling system can be markedly improved by eliminating the excessive time lag between sampling and analysis.

Jan 1, 1981

"The ventilation-related risks from mines with elemental sulphur include dust explosions, spontaneous combustion with emission of heat and toxic sulphur dioxide or hydrogen sulphide gases, reactions with nitrates, corrosion, acid water, and pyrophoric reactions with naked iron or other metals. Elemental sulphur will form explosive mixtures in air at lower dust concentrations and at lower ignition temperatures than coal or sulphide dusts. Potential controls include primary ventilation circuit design, control of dust deposition and static discharges, enclosing steel surfaces, inert stone dusting, FRAS ducting, humidifying the air, alternate stench gas, self-contained self-rescuers with goggles, careful siting of underground infrastructure, controls on explosives formulations and procedures, mining method selection, controls on surface temperatures and protection of equipment, careful materials selection for ventilation seals and changes to worker clothing and training.INTRODUCTIONSulphur (“Brimstone” in biblical times) is one of the world’s most important industrial feedstocks and is used in a wide range of chemical processes and industries. Until the early 20th Century, most of the world’s production of sulphur came from ‘conventional’ underground mines in Sicily (Demetra produzioni, 2006; Bellia, 2006). This was a hazardous activity. The Frasch solution mining process replaced traditional underground mining of sulphur until the late 20th Century. Most of the world’s production of elemental sulphur is now as a by-product from sour gas produced in petroleum refineries and natural gas installations (Anon, 1993). As such, there is considerable experience in understanding and managing the hazards of elemental sulphur in chemical plants and surface transport.Whilst rare, underground mines with high elemental sulphur contents (as a gangue mineral) create an unusual range of mine design and operational issues, including many ventilation-related ones. The key hazards from elemental sulphur include: primary and secondary elemental sulphur dust explosions, fires and burning (with emission of heat and sulphur dioxide or hydrogen sulphide gas), reactions with nitrates used in explosives, corrosion of steel and other metals, generation of acid water (especially at higher water temperatures), and pyrophoric reactions with naked iron (e.g., ground support, ladderways or underground fixed plant) or other metals including silver and copper (e.g., used in electrical components and equipment)."

Jan 1, 2019

The Ernest Henry Mine is an open pit copper-gold mining operation located in north-west Queensland, Australia. It is owned and operated by Xstrata Copper with a current concentrator throughput of approximately ten million tonnes per annum. The pit will cease mining towards the end of 2010. Extensive surface diamond drilling has confirmed an extension of the orebody to depths of 1000 m below surface. A prefeasibility study was commissioned in late 2006 to investigate underground mining options with the preferred mining method being an inclined sublevel cave. In February 2008 mining of a decline commenced in conjunction with a feasibility study to further investigate the project. Work from the prefeasibility study indicates that an underground crusher, conveyor and hoisting shaft could be utilised to crush and transport broken ore from the sublevel cave workings to the concentrator. The study suggests that a production rate of five million tonnes per annum could be achieved and sustained for up to ten years. Ventilation designs and requirements will form a large section of the feasibility study. This paper will detail investigations of preliminary ventilation network designs of the proposed sublevel cave. Work has been completed using both Ventsim and VumA ventilation simulation packages. Ventsim was used to provide preliminary estimations and suggest alternatives for: surface fan duties;airflow characteristics (direction, velocity, pressure and quantity); andventilation network design in key mine areas. With mining activities reaching depths in excess of 1000 m below surface an analysis of heat conditions should be conducted. The VumA software package was used to model the thermal properties of the ventilation system. This model will provide a basis for the preliminary decisions on refrigeration requirements for the mine.

Jan 1, 2008

By Romeo S. Jurani

Yucca Mountain, located in Southern Nevada approximately 160 krn northwest of Las Vegas, is currently the site of intensive surfacebased and underground investigations. The investigations are required to determine if the site is suitable for long term isolation of the Nation's high level nuclear waste inventory. A major component of the program is the Exploratory Studies Facility, or ESF. The ESF, when completed, will consist of approximately 25,600 meters of tunnels and drifts. The network of tunnels and drifts (Figure 1) will house and support a wide array of testing programs conceived to provide physical information about the site. Information on geologic, geomechanical, and hydrologic data will be used in the repository design if the site is found suitable. Besides a few special requirements, the general ESF ventilation criteria during construction are similar to that of commercial tunneling and mining operations. The minimum air velocity at the Tunnel Boring Machine (TBM) and other active mining faces is 0.51 meter per second (m/s) (100 feet per minute [fpm]). Airways, estimated leakages and ventilation controls are converted into equivalent resistances for input to mine ventilation network computer simulations. VNETPC Version 3.1 computer software is used to generate the ventilation models for optimized system design and component selection. Subsequently, actual performance of the ventilation system will be verified and validated to comply with applicable nuclear regulatory quality assurance requirements. Dust control in the ESF is dependent on effective dust collection, enclosure, and airflow dilution. Minimum use of water, as feasible, is necessary to avoid adding moisture to the potential repository horizon. The limitation of water use for test drilling and TBM operation, and the rigid compliance with applicable federal and state regulations, make the ESF a ventilation design challenge.

Jan 1, 1995

By Euler De Souza

"The uninterrupted operation of a ventilation system is critical to ensure the mine meets its scheduled production and, as important, is vital to the health and safety of all personnel working underground. Those operating the mine ventilation system must have fundamental engineering training in the art of fluid dynamics and have a good comprehension and control of the mine ventilation network. Ventilation management by untrained and inexperienced personnel may result in serious consequences when the system becomes ineffective. This paper shares observations and experiences pertinent to the occurrence of upset conditions as a result of the improper design and operation of mine ventilation systems. A series of real life case studies are presented to describe disruptions to mine ventilation systems and the gradual deterioration of system operational efficiencies leading to eventual failure. Special focus is given to mistakes made and on the resulting serious consequences. The case studies also demonstrate how each upset condition was resolved, permitting the mines to safely resume production activities.INTRODUCTIONThe ventilation of operating mines is a continuously changing and evolving system; upset conditions will occasionally occur, but should be promptly resolved in order for the system to function properly, according to design, and in compliance.Those designing, managing or operating the mine ventilation system must have pertinent training and have a good understanding of fundamental ventilation concepts to be able to devise and implement engineering solutions to day-to-day challenges. Realistically, the operator must also have extensive practical experience and be able to effectively apply operating procedures, design criteria and ‘best practices’. They must be able to, on a daily basis, evaluate the mine ventilation system, determine and locate any problems, understand the causes of each problem, find a solution, and promptly and efficiently correct those problems.Ten case studies are presented to demonstrate how fundamental design or operational mistakes can lead to adverse conditions or to catastrophic consequences, how detailed on-site engineering assessments can be employed and how simple, low cost, engineering solutions can be implemented to successfully resolve the issues and return the ventilation system to compliance, permitting the mines to safely resume production activities."

Jan 1, 2019

By B. A. Ashley

In 2007, Rosebud Mining Company (RMC) opted to extend the reserve base of Tracy Lynne Mine by developing through a sandstone channel. The extension provided access to approximately 6 million additional recoverable tons (approximately 8 years of mining) which originally had been deemed inaccessible. An evaluation of the mine?s existing ventilation system, which was designed to meet the needs of the original limited reserve, concluded that two ventilation shafts would likely be required to adequately ventilate the projected workings in the expanded reserve. To assist in the evaluation, a ventilation model of the mine was developed using Ohio Automation?s ?ICAMPS MineVent? software based on field data from Tracy Lynne Mine, prior ventilation survey experience at similar RMC mines, and relevant published sources. Model results suggested that the most economical shafts would be an 8-ft diameter return and a 4-ft diameter intake. Unfortunately, issues related to property leasing and shaft site permitting caused construction delays. Therefore, the model was also used and proved to be effective in prioritizing interim ventilation upgrades which could be implemented in order to maintain coal production. Model results indicated that the best interim upgrades included rehabilitating restricted entries and damaged stoppings and replacing the main fan with a higher pressure fan. From late 2010 to mid-2012, all interim upgrades and shafts were implemented. Current models and mine experience indicate that ventilation will not be the limiting factor for mining the additional reserve.

Feb 23, 2014

By B. A. Ashley

Rosebud Mining Co. (RMC) is based in Kittanning, PA. As of October 2013, it operated 24 active underground mines in Pennsylvania and Ohio. RMC?s Tracy Lynne Mine is located approximately 5 km (3 miles) east of Apollo, PA, (approximately 48 km or 30 miles northeast of Pittsburgh, PA) and mines the Lower Kittanning coal seam. The coal seam averages approximately 1.1 m (45 in.) thick and is of steam coal market quality. The mine is a single unit operation. Coal is mined using a continuous mining machine and is transported from the face to the conveyor belt using a continuous haulage system. Typical ventilation in the mine consists of an exhausting fan that draws air through isolated intake, belt and return air courses (Fig. 1).

By G B. French

Post a serious heating event underground, and at the direction of the State Mining Safety Authority, a mining company needed to demonstrate the use of cutting-edge technology to mitigate future events. Yokogawa were contracted to provide a turnkey solution to help the mine achieve this objective. The solution was to use a fibre optic-based Heat Detector that will allow entry into and around the mine considering the potential volatility of the environment, also the need to redeploy as mining activities moved underground and more boreholes are added. Industrial strength fibre optic cable and a robust connector system was chosen to achieve this goal and give the customer the ability to send cable down boreholes of up to +1 km and continuously monitor the temperature ofunderground roadways. Being able to re-deploy the cables into different boreholes and link borehole temperature measurements gave insight into all areas on the mine. The machines deployed on-site were the Yokogawa DTSX1 heat detector incorporating the Ramen Backscatter principle. Being of a robust construction and a low power consumption device, it was easily included into the portable monitoring trailers designed by the customer and built locally.

Oct 12, 2022