Search Documents

By A. Hynes, T. Skulski, D. Francis

The Archean volcano-sedimentary succession in the LG-3 area has undergone two phases of deformation and has been metamorphosed to upper greenschist and amphibolite facies. Marine, fine-grained sediments and mafic pyroclastics comprise the lowest observed stratigraphic unit. These sediments are overlain by a thick sequence of submarine basalts and minor basaltic andesite. The lavas are characterized by high Al/Al+Si, Ti values, low Mg numbers and flat REE profiles (lOx chondrite). A sedimentary prism of coarse elastics which was deposited close to an exposed plutonic highland, overlie the volcanics. Massive lavas of basaltic andesi te and associated volcano-sediments comprise the uppermost stratigraphic unit. These lavas are characterized by high Mg numbers, Ni, Cr, LREE (lOOx chondrite) but low Ti, Al/Al+Si and HRee. The supracrustal rocks were intruded by tonalites and tonalitic gneisses.

Jan 1, 1984

By I. Dimitrov, S. R. McCutcheon

"Industrial-grade limestone is found in both the Lower Silurian La Vieille Formation and Upper Silurian LaPlante Formation of the Chaleurs Group in northern New Brunswick. Currently, between 150 000 and 200 000 tonnes of limestone are produced per year from the proximal facies of the LaPlante Formation at the Sormany quarry of Elmtree Resources Ltd., located west of Bathurst.The proximal facies of the LaPlante Formation was deposited on the margins of tectonically uplifted Ordovician terranes. This facies comprises stromatoporoidal-algal bindstone intercalated with wackestone, packstone, and floatstone in variable proportions. The distal facies comprises calcareous shale and minor limestone deposited deeper offshore.Folding and faulting related to Middle Devonian Acadian tectonism have caused an increase in the apparent thickness of the limestone sequences, especially adjacent to the regional Rocky Brook-Millstream fault. Structural and stratigraphic observations indicate that some of the limestone bodies in the area have been tectonically displaced from their site of deposition.A variety of prospecting techniques was used to locate new limestone resources, including geological mapping, airborne and ground electromagnetic surveys, and satellite remote sensing. Clastic rock units above and below the LaPlante Formation have distinctive properties that help to trace the intervening limestone along strike. Because of water-saturated glacial cover, thick vegetation, and the small size of targets, airborne geophysical methods did not prove effective in delineating limestone beds, but aeromagnetic surveys helped map the underlying clastic unit. The remote-sensing data and especially high-resolution digital elevation models helped in identification of karst topography related to limestone."

Jan 1, 2007

By W. A. Padgham, H. Helmstaedt

Field evidence for current hypothe e about age and kinematic ignificance of gold-bearing hear zones in the Archean Yellowkni fe greenstone belt is reviewed , and it is concluded that major disagreements between previous workers are a direct result of differences in stratigraphic and tructural in terpretations of the Yellowknife Supergroup. Although goldbearing hear zone appear to be confined to the mafic volcanic pile of the Kam Group. it can be shown that shearing affected all supracru tal rocks, including the Jackson Lake Formation. now con idered to represent the youngest unit of the Yellowknife Supergroup. tructural ob ervations are incompatible with the hypothe is that the hear zones represent loci of ynvolcanic gravity sliding but are consistent with earlier conclu ions that shear zone development commenced with rotation of the volcanic pile and continued as re ult of lateral shortening broadly overlapping with the emplacement of granitoid batholiths. Shear Zones are common throughout the entire green tone belt. yet productive zone are confined to the Yellowknife Bay Formation of the Kam Group and localized where flow abut with a high angle again t the contact of the We tern Plutonic complex. However. no obvious tructural and lithological features have been recognized that are more favorable for gold deposition and distinguish the shear zones and flows of the area around the mines from those of other parts of the greenstone belt. The model that gold wa transported by metamorphic solutions and that hear zones were the firs t-order control for gold deposition provides no explanation for the trong localization of the depo it . As porphyries with elevated gold contents are present in and near ome of the mines. the possibility that gold was deposited from hydrothermal system around fel ic intrusion representing early phases of the Western Plutonic complex should be given erious consideration.

Jan 1, 1986

By Gregg W. Morrison

"The Craigmont copper-iron skarn deposit is adjacent to the southern margin of the late Triassic Guichon Creek batholith in south-central British Columbia. Host to the ore are sedimentary and volcanic rocks of the western calc-alkaline belt of the Upper TriassicNicola Group. In the mine area, the Nicola Group rocks are a stratigraphically complex sequence, at least 1800 feet thick, which have been subdivided into Basalt, Rhyolite, Carbonate and Clastic Sediment units. All the units strike and dip parallel to the margin of the Guichon Creek batholith and are within the batholith contact aureole. However, only the Clastic Sediment unit is in contact with the batholith.Most of the skarn and ore is within the Carbonate unit and more specifically within an Interbedded facies that consists of lime sandstone, lime siltstone, quartzo-feldspathic siltstone and argillite. The Interbedded facies and the adjacent barren Massive Limestonefacies are interpreted aspart ofa carbonate reef complex. The distribution of skarn and ore within the Interbedded facies suggests that the facies boundary was a physical and chemical barrier that resulted in concentration of metals adjacent to the Massive Limestone facies.Two stages of skarn formation have been recognized at Craigmont. In Stage I, ore-bearing magnetite-rich and actinolite-epidote-magnetite skarns developed both in basaltic rocks and in Fe-bearing siltstone and argillite of the Interbedded facies, while barren grossular garnet-epidote-calcite-pyrite skarns developed in Fe-poor rhyolitic bands within the Interbedded and Massive Limestone facies . In Stage ll, massive, barren grandite garnet skarn replaced mineralized Stage I skarns in the vicinity of diorite plugs. and specularite ore formed in brecciated Stage I skarn and clastic rocks away from the plugs. Theformation of Stage I skarns required no addition of material, only redistribution and concentration of elements already present within the Interbedded facies. However, the concentration of Cu in Stage lore requires a mechanism for more efficient leaching of Cu from the host rocks, an anomalous concentration of Cu at the site of the Stage I orebody or an additional input of Cu from an external source. The formation of Stage II skarn and ore requires only remobilization and recrystallization of Stage I skarn and ore.Copper and iron are the only elements in economic concentrations in the ore and chalcopyrite is the only significant copper-bearing mineral. Chalcopyrite is disseminated and interstitial to magnetite in Stage I mineralized skarns and is interstitial to specularite in the matrix of Stage II breccia ores. Chalcopyrite also occurs with pyrite as stringer ore in bleached • sediments and rhyolite tuffs in the stratigraphic footwall of the main orebodies.The Craigmont deposit has more features in common with Cu-Fe deposits hosted in metavolcanic and metasedimentary rocks than it has with typical skarn deposits associated with porphyry copper deposits. The orebody is more likely a product of concentration of metal contained within the Nicola Group rocks than of the mineralizing event that produced the . Highland Valley Cu-Mo porphyry deposits in the central part of the Guichon Creek batholith ."

Jan 1, 1980

By J. Guha, A. Gobeil, P. Pilote, A. Tremblay, E. Dimroth

The Mount Bourbeau Lac Berrigan area is located just to the north of the Town of Chibougamau. The axial trace of the Chibougamau syncline borders the northern part of both areas. The area contains Archean rocks of the Roy Group, intruded by the Cummings Complex and the Line Lake tonalite stock. Proterozoic sedimentary rocks occur in a series of outliers. Various Cu, Zn, Pb, Ag, Au and Mo showings are dispersed over the area in a wide range of time and space. Pre-Kenoran (stratiform and stringer) showings related to volcanic activity may be distinguished as well as the syn-or post-Kenoran (vein) types whose nature is imprecisely known. In this area, the stratiform showings occur in the Gilman and Blondeau Formations, whereas the vein type showings occur for the most part in fractures or breccias within or along the contacts of the various sills of the Cummings Complex. Mount Bourbeau is distinguished by the greatest variety of showings as well as the proximal volcanic facies of the Blondeau Formation. A volcanic centre is presumed to lie a short distance north or east of the locality. Locally, the Line Lake stock contains significant silver, molybdenum and gold mineralization. Its role as a metal reservoir, a source of heat for the circulation of hydrothermal fluids and its control of the local tectonic style remains to be determined.

Jan 1, 1984

By Stewart R, Manson RA, Haig DW, Perembo RCB, Kruman B

Since the advent of plate tectonic modelling, the Ramu-Markham valley has been thought the site of a classical island-arc/conti- nent collision zone. In this interpretation the units south of the Markham Valley are held to be island are / micrcontinental mate- rial accreted to Australia and those north of the valley are thought to represent a separate Finisterre island-arc terrane. Recent remapping by the Geological Survey of Papua New Guinea shows: (1) there is no terrane boundary along the Ramu-Markham valley (2) the Finisterre Volcanics are probably part of either a fore-arc sequence or oceanic plateau obducted onto a microcontinent/ volcanic-arc composite terrane, accreted to the continental Australian plate. A new tectonic model is proposed for northern PNG and involves: (I) Eocene to Late Oligocene subduction below a microcontinent remote from Australia to produce the Sepik are and related intrusives, the Finisterre Volcanics (fore-arc or possible oce- anic plateau), together with the Alife blueschist. (2) obduction of the Sepik arc in Late Oligocene-Early Miocene times over the advancing Australian plate. This resulted in crustal melting, some of the products of which are the Mid- dle to Late Miocene Akuna and Bismarck intrusive complexes of the Maramuni arc. (3) obduction of the Finisterre Volcanics began in Early Pliocene times and continues today. (4) post-Middle Miocene mineralisation is the result of melting after obduction of the Sepik microcontinent.

Jan 1, 1997

By M E. Barley, A D. George, M Kneeshaw

Detailed pit and outcrop mapping of sedimentary rocks and their alteration is providing insights into fluvial processes that operated during deposition of the world-class Yandi channel iron deposit. Five prominent rock units are traceable along the strike of the Yandi deposit and permit correlation of open pits and mesas. These units are the Eastern Clay Horizon (ECH), granule-pebble conglomerate (GPC), Main Ore Zone (MOZ), Basal Denatured Zone (BDZ), and Basal Conglomerate (BCONG). The upper part of the deposit is characterised by a transition from spheroidal grains with well-defined rims and nuclei to larger, subangular grains with poorly developed rims. The distribution of rock types and sedimentary features such as lateral accretion surfaces, channel scours and fills, graded bedding, cross-bedding, reworked horizons, and slumped strata are common at Yandi and indicate deposition in a fluvial system. Bedding is well preserved despite modification of original grain shapes and textures and introduction of secondary silica and alumina in the upper part of the deposit. The high lithic and clay content of the GPC and ECH possibly reflect changes in source area or a hiatus in deposition of the Marillana Pisolite. The MOZ and the BDZ may be the same depositional unit with the latter recording alteration by groundwater and destruction of primary textures and other sedimentary features. The BCONG is a channel lag deposit reworked during deposition of the MOZ. This interpretation is supported by the dominance of basement-derived lithic clasts, the presence of BCONG clasts, the variable thickness of the unit along strike and the presence of BCONG clasts in the BDZ.

Jan 1, 2002

By B. R. MacKay

Introduction During the past six seasons the writer has been engaged in semi-detailed investigations on the coal areas lying along the front of the Rocky mountains between the Brazeau river and the Smoky River Coal Reserve (see Map, Figure 1). The purpose of this paper is to present some observations pertaining to the stratigraphy and structure of the district, touching especially upon the lithological units into which the Lower Cretaceous sediments have been divided, the thicknesses of the formations at different localities, the number, thicknesses and horizons of the principal coal seams, and the structural conditions which exist in the various fields.

Jan 1, 1930

By P Hawke, J Hurst, B KrapeP

Hancock Prospecting Pty Ltd (HPPL) drilled two deep diamond stratigraphic holes (ECD0001 and RHD0296) within the eastern Fortescue Valley in the Pilbara of Western Australia. Located south of the Roy Hill Iron Ore project, the holes aimed to define the stratigraphy of the Marra Mamba Iron Formation (MMIF) of the Chichester Range and its south-dipping extensions below recent cover. Previous attempts to define the MMIF of the Chichester Range have resulted in differing interpretations due to the data available at the time.The unweathered MMIF beneath the Fortescue Valley in the HPPL drill holes is characterised by dolomitic carbonate interbedded with stilpnomelane-rich shales, chert and banded iron formation (BIF) with hematite staining. This intersection equates to ~75 m of carbonate-facies iron formation, as opposed to the ~230 m thick oxide-facies BIF and shale sequence encountered south of the Fortescue Valley.Various detailed geological core analyses and interpretations from ECD0001 and RHD0296 were integrated with regional diamond and reverse circulation (RC) holes from across the Fortescue Valley. Interpretation of the data indicates that the eastern Fortescue Valley MMIF represents a thinned thickness sequence of the whole formation. The MMIF of the Chichester Range and Fortescue Valley has gamma logs that correlate strongly in parts to the type section used for MMIF south of the Fortescue Valley. Therefore, the outcropping MMIF in the Chichester Range represents an eroded equivalent of the æreducedÆ thickness MMIF observed in ECD0001 and RHD0296.Data from deep diamond drill holes across the valley, from the Hamersley Basin to the Carawine Basin, were correlated. The correlation shows that the depositional site of the MMIF in the HPPL diamond drill holes is consistent with a proximal ramp setting, in which iron-rich shales wedge up-palaeoslope and shelf-derived carbonate turbidites wedge down-palaeoslope. Not only is it the occurrence of these shales that define the MMIF, but they also determine the northward potential to develop orebodies, as they are the source of iron from which iron-rich oxides and carbonates of metamorphic or diagenetic origin form.CITATION:Hurst, J, KrapeP, B and Hawke, P, 2013. Stratigraphy of the Marra Mamba iron formation within the Chichester Range and its implications for iron ore genesis at Roy Hill - evidence from deep diamond drill holes within the East Fortescue Valley, in Proceedings Iron Ore 2013 , pp 91-106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By D. Goffaux

In less than two years, Stratmin has discovered, explored, developed, financed and put into production by open pit, a large graphite mine. The deposit, hinted by airborne electromagnetic survey, was discovered in September 1987 through various ground geophysical surveys, diamond drilling and trenching. The open pit started production in February 1989, feeding a nearby leased mill at Notre-Dame-du-Laus (Quebec), having a processing capacity of 400 tons per day. A new 1,000 tonne per day mill was built at the mine site, in Lac-des-lies (Quebec) and began production in April 1990. The Lac-des-lies graphite operation is currently one of the largest of its kind in the world. Mine and mill facilities are operated by Stratmin Graphite, jointly owned by Stratmin Inc. (75%) and Imetal-France (25%), a wholly owned subsidiary of Imetal (France). From initial exports limited to Japan and United States, Stratmin Graphite is now exporting in fourteen different countries, attesting to the very high quality of its products, with grades ranging from 92% to 97% carbon. Among the numerous graphite deposits discovered in Canada, Stratmin Graphite Inc. has emerged as the leader and virtually the sole crystalline graphite producer in North America, operating on a continuous basis.

Jan 1, 1992

By John V. Beall

STREAM pollution caused by waste waters from mineral industry operations is a problem that has grown up with the industry. Its importance to each operator is dependent on the amount and type of waste he dumps into the rivers and streams; on whether this waste pollutes the waters sufficiently to make them unfit for potable water, irrigation, and conservation of wild life; and on whether this waste makes a safety or health hazard. Through the years our growing population and industry have made increasing demands on the mineral industries, the suppliers of the raw materials on which our industries are based; and we have met these demands at some sacrifice to the natural beauty and cleanliness of our country. However, that is often the unavoidable nature of the business, and along with the increased use of our

Jan 1, 1948

By M. Baumann

Operating and maintaining the heavy equipment used in open-pit mining operations is an ongoing challenge for mines. Typical operations employ a combination of shovels, wheel loaders, and haul trucks to excavate and transport the material for further processing. As this is the first point of contact for the material after blasting, it is often a bottleneck of all downstream processes, thus, equipment uptime and efficiency is crucial. Automated systems for bucket tooth monitoring, payload measurement, proximity detection, and rock fragmentation analysis will be examined. The impact of these systems on operation safety, efficiency, and reliability, in real-world scenarios will be investigated. The process of managing all the above fleet of equipment in a mine can be streamlined by connecting the equipment monitoring systems to a central server. Using the central server, the distribution of this information can be automated to ensure that the right people see the data in a timely manner, improving both proactive and reactive responses to threats to safety and productivity.

Feb 23, 2014

By W Newns

This paper describes laboratory and in situ tests and determines a set of parameters for stiffness and strength properties for a weak sedimentary rock mass, the East Coast Bays Formation of Auckland. The parameters derived are discussed in relation to peak strength and in respect of deformation limits associated with sequential excavate and support (SEM) or conventional tunnelling.

Mar 8, 2011

By M. Razavi

This investigation is part an overall investigation on the effect of sodium silicate on the properties of the mine backfill. The results presented will highlight the effects of binder dosage, sodium silicate concentration, and pulp density on the performance of stabilized sodium silicate-fortified sand pastefill samples. Binders implemented for these experiments consisted of cement, slag, and sodium silicate in various proportions. The binder content varied from 3 to 9 wt% (total dry weight) and sodium silicate concentrations was adjusted at 2 and 4% (total binder weight). Moreover, pulp density was adjusted to values between 80 and 83 wt%. For completion of the aforementioned phase of the study, series of sand pastefill test samples were prepared and cured for 28, 56, or 120 days, in a humidity and temperature controlled room. The specimens were tested for uniaxial compressive strength (UCS). In order to study the effect of sodium silicate on microstructures of stabilized sand pastefill, some MIP tests were conducted on selected samples. The results of this investigation evaluate the use of sodium silicate as a partial replacement of cement in stabilized backfill. The analyses of the results demonstrates that, with an increase in binder content and a decrease in pulp density, the UCS values of sand pastefill samples increase. Further more, the results indicate that increase in addition of sodium silicate does not necessarily result in higher strength minefill.

May 1, 2007

By F. P. Hassani, Jacque Ouellet, M. Hossein

A laboratory investigation was undertaken to evaluate the effectiveness of different binding agents in a paste backfilling operation suitable to be used in a sulphide-rich environment. Different combinations of Portland cement and fly ash type C as well as ferrous slag were used as the binding agents. The unconfined compressive strength of the samples was measured for extended curing periods. The results indicate that the addition of 3% slag in the binding agent mix could produce strengths up to 0.5 MPa in the samples under investigation. For higher binding contents, the addition of Portland cement will lead to higher availability of calcium hydroxide and calcium aluminate, which are susceptible to deterioration from the phenomenon known as sulphate attack. Using slag, on the other hand, will reduce the permeability, availability of calcium hydroxide, and dilute the calcium aluminate ions reducing the susceptibility of the samples to sulphate attack. However, gypsum will form which could have the same detrimental effect on the strength of the treated matrix. Therefore, special attention must be given to the content and properties of agents used to activate the pozzolanic properties of the slag.

Jan 1, 2001

By Pei‑liang Xu, Jun Wang, Xi Zhang, Deng‑pan Qiao, Tian‑yu Yang

The surface backfill, serving as the operational platform for continuing mining in upward slicing and filling stopes, is required to possess sufficient strength and thickness. Currently, there are limited model methods for determining the strength and thickness of the surface fill body. By analyzing the mechanical actions on the surface backfill, it is determined that its stability is mainly influenced by the combined effects of normal and tangential uniform loads under full-load conditions of trackless equipment. Assuming a circular contact surface between the tire of the trackless equipment and the surface backfill, and utilizing solutions from elastic mechanics theories such as the Boussinesq and Cerruti solution, the stress and displacement distribution of the surface fill body were obtained. Based on the maximum vertical stress condition, where the surface backfill body undergoes maximum deformation while still in an elastic state, and considering the stress–strain relationship, a model for the strength and thickness of the surface backfill has been established. According to the research findings, the design for the strength and structural parameters of the surface backfill has been developed to meet the full-load operation of the Atlas ST7 scooptram, with a compressive strength of 1.32 MPa and a thickness of 0.5 m. Numerical simulation analysis results indicate that the stress and displacement of the surface backfill align with theoretical analysis results. Practical results from industrial application in the western section of the Dahongshan Copper Mine demonstrate that the designed strength and thickness of the surface backfill meet the operational requirements for trackless equipment, resulting in significant engineering application effects and economic benefits. The research findings hold significant importance for advancing the theory of backfill mining and have high applicability and promotional value for similar mines.

Mar 24, 2024

By M. L. Jeremic

Altered and unaltered coal from the Star-Key Mine near Edmonton, Alberta has been tested under compression and under tension. The test results showed that altered coal samples have an appreciably lower strength than unaltered coal. Altered coal samples do not give a linear load-displacement curve, peak strengths are poorly defined and yielding is observed over a range of loads, so the material can be regarded as relatively plastic. However, unaltered coal samples produce a linear loading curve with a high tangential modulus and an easily distinguished peak strength at which there is a sudden brittle failure. These findings lead to important differences in the theoretical design of ribs and pillars in underground mines in the two coal types. The substantial differences in the strength properties and behaviour of the two types of coal are governed by a higher intensity of cracks in the weathered coal. Two causes of the additional cracking can be suggested-subaerial weathering and subterranean weathering of the coal.

Jan 1, 1979

By Piotr Malkowski

Studies on the properties of rocks heated to high temperatures are rather rare. Such research is occasionally conducted for example; in areas around nuclear power plants. The national Polish coal gasification (underground coal gasification, or UCG) project has, however, forced the analysis of the geomechanical properties of heated rocks in the vicinity of a designed geo-reactor. Ukrainian experience with UCG show that rocks up to 2 m from the burned coal seam be at a temperature > 600ºC. Such a high temperature will undoubtedly influence their physical properties. This paper presents studies on the strength and deformation properties of carboniferous rocks in the Upper Silesian region, where the UCG process is planned. Three types of rocks were tested: claystones, mudstones and sandstones. Laboratory tests of these rocks evaluated compressive strength, elastic modulus and weight loss. An evaluation of the results of the tests comparing the thermal conductivity of rocks and their specific thermal capacity was then carried out. All of the rocks studied were heated to 300, 600 and 1000ºC, and also evaluated at room temperature. This procedure shed new light upon the behavior of heated rocks in relation to their distance from the designed geo-reactor. The test results presented were developed within Research Task No. 3 ?Developing a technology of coal gasification for efficient production of fuels and electric power?, financed by The National Centre for Research and Development under strategic research and development programme ?Advanced Technologies for Energy Generation.?

Aug 1, 2013

By Ching L. Wu, Joseph Penzien

An analytical procedure is presented for evaluating the stresses in linings of bored tunnels caused by kinematic soil-lining interaction. Three cases of interaction as produced by the following conditions are treated: (1) relaxation of in situ soil stresses near a lining following its installation; (2) overburden pressure at the soil surface; and (3) free-field soil response resulting from an earthquake. Non-dimensional formulas and graphs resulting from parametric studies are presented for practical tunnel design applications. The procedure is applied separately to a steel lining and a concrete lining for a site located at the lower end of Market Street in San Francisco through which a BART (Bay Area Rapid Transit)tunnel passes.

Jan 1, 1997

"Acid resistant brick lined autoclaves and related vessels are utilized in pressure oxidation for the recovery of gold, copper, and other metals. The combination of the corrosion resistant membrane, acid resistant brick, mortar and steel shell is a composite system that requires a sophisticated stress analysis. In order to obtain meaningful results both the model and physical properties of the materials must be carefully selected. Evaluation of the calculated results requires an understanding of both the failure mechanisms of ceramics and experience with the performance of existing lining systems.INTRODUCTIONAcid brick lining systems are used in pressure oxidation autoclaves and related vessels to provide thermal and mechanical protection for corrosion resistant membranes that are applied directly to the interior of the vessel shell. The acid brick and mortar must be resistant to the process conditions and must provide a mechanically reliable structure.The construction of lined vessels incorporates a wide range of materials that can include the carbon steel vessel, austenitic weld overlay, lead lining, organic membrane, ceramic brick, mortars and other alloy components. The physical properties of the materials can vary by orders of magnitude and when combined in the construction of the lined vessel create a complex composite structure. The materials may be bonded together or act independently of each other. Stresses are induced into the lined vessel include pressure, thermal expansion, chemical expansion and mechanical loads.The complexity of these systems makes it is very difficult to account for all of the variables in the structural analysis of lined vessels. Historically calculations were simplified and designers primarily relied on experience with previous applications.The greatly improved tools for Finite Element Analysis (FEA) available today allow for detailed calculation of the stresses imposed on the vessel shell and lining. Koning & Lauzon (2004) presented a paper on design fundamentals including a discussion on the application of FEA methods at Pressure Hydrometallurgy 2004 in Banff. When a designer carefully constructs a model and selects the correct materials properties for the calculations, meaningful and useful results can be achieved."

Jan 1, 2012