Search Documents

By Joe B. Rosenbaum

Fine-sized mineral wastes discarded by ore milling plants require stabilization to prevent air and water pollution. Methods devised for achieving this stabilization include physical, chemical vegetative, and combination procedures. Although vegetative reclamation is preferred to physical and chemical stabilization, it is difficult to achieve because the wastes are sterile, contain deleterious inorganic salts, and lack the essential nutrients and physical characteristics required for sustaining vegetative growth. Nevertheless, recent research has developed methods for producing vegetative growth on all but excessively acidic, basic, or saline tailings at costs ranging from $100 to $650 per acre. This report summarizes effective procedures developed for vegetating average tailings, the cost differential between the various methods, and suggests procedures that may be applicable for achieving stabilization of pyrite-containing wastes that may oxidize and become excessively acidic. The use of buried layers of sewage sludge to prevent this acidification is discussed.

Jan 1, 1972

By Travis A. Shoemaker, Mitchell S. Youmans, Nancy T. Chin, Michael S. Senior

A geologic assessment and stability analysis of the right abutment of Boundary Hydroelectric Dam in Pend Oreille County, Washington was completed in May 2017. The stability analyses identified a potential failure plane of a rock block that supports a bridge abutment, and weight restrictions were established to reduce the bridge loads. To restore full use of the bridge, a long-term stabilization solution was designed. A two-phased construction approach was implemented to reduce risk: (1) cable lashing and wire mesh and (2) 24 permanent post-tensioned tiebacks. The tiebacks were located and sequenced based on stabilization effect and site access to incrementally ease the bridge loading restrictions throughout construction. Due to weight restrictions and site tolerances, all work was performed with rope access construction methods. The contractor’s means and methods, tight drilling tolerances, and an exploratory adit within the rock block made the construction uniquely challenging. Due to limited exploratory data and irregular rock face geometries, the design orientation, location, and tolerances of the tiebacks were established in a 3D Building Information Model (BIM). The 3D model was revised frequently during construction to 1) model the as-drilled conditions of the tiebacks; 2) compare with the remaining proposed anchors; 3) anticipate the contractor’s sequence to reduce risk during drilling; 4) accommodate the contractor’s requests for information; 5) make design changes based on field observations; and 6) incrementally assess rock block stability. The 3D model was created using BIM software and automated using custom programming to link per-plan, proposed, and as-installed tiebacks between the 3D model, field logs, and a stability analysis. This system allowed for a near real-time 3D model and stability analysis, which were easily communicated between the design team and field staff. This workflow and automated model nearly eliminated manual editing of the 3D model, accelerated contract document response time, and helped reduce risk for the owner, contractor, and engineer. Here, we present a successful case study utilizing the Observation Method and a real-time 3D model to complete a project with numerous complexities relating to design, communication, and risk.

By James J. Brady, Kenneth L. Faught, Chadi El Mohtar, Chaoshi Hu

"During construction of a 9.5-ft. diameter sanitary sewer tunnel, the City of Edmonton encountered a large pocket of flowing sand that flooded their TBM and caused significant surface subsidence, stopping further tunneling by the TBM through this zone. A unique collaborative effort ensued between the authors representing the city, consulting engineers and academic researchers to develop the optimal strategy for grouting the problematic soils. The site has a layer of very find sand between 20 and 30 ft. in depth with fines contents ranging from 5% to more than 40%. The collaboration extended from requesting additional site investigation efforts to shipping samples to the UT-Austin laboratories for grout testing plus ground and grouting characterization tests resulting in field recommendations for a full scale ground improvement program. New research information on the grouting of fine sands along with a collaborative framework for the design of in-situ grouting projects are the key topics presented. INTRODUCTION Encountering a large unexpected pocket of flowing sand with an open-faced TBM while excavating a tunnel below the groundwater table is never a good thing. This was certainly true for the City of Edmonton when one of their Lovat TBM’s became inundated by flowing sand while excavating the 9.5-ft. diameter Millwoods Double Barrel Replacement Tunnel in September 2013. However, since the City of Edmonton self-performed this work, a rare situation existed where the site could be investigated objectively, without the prejudice of contending parties selectively influencing how information was gathered and presented, to accurately examine site conditions with a goal of identifying the best remediation measures."

Jan 1, 2016

By S D. Golding

The current study integrates hydrogeochemical and stable isotope results to investigate the sources and evolution of acid mine drainage at the historic Mount Morgan gold mine in Queensland, including the controlling factors and mechanisms of sulfate formation. The open pit and seepage sumps contain acid-sulfate waters and show elevated Al, Cu, Fe, Mn, Pb and Zn values. Samples collected from the Dee River bordering the mine site are less acidic, with lower concentrations of dissolved metals that gradually attenuate downstream from the mine. Concentrated acid mine waters has lead to formation of efflorescences consisting mainly of hydrous Fe-sulfates. The results of the ongoing isotope analyses on water samples show distinctive grouping of the data. The range of the sulfur isotope values for dissolved sulfate in samples from the open pit and sumps (d34S = 2.1 to 3.0 per mil) are similar to those of sulfides in the Main Pipe mineralisation (d34S = - 0.2 to 2.8 per mil). The lack of fractionation between sulfides and sulfate indicates that intermediate oxidation states of sulfur are not significant and makes this technique a useful tracer to identify the sources of sulfate. The Dee River samples, on the other hand, have heavier sulfur isotopes (d34S = 2.8 to 5.0 per mil). These samples may contain dissolved sulfate from æinternal sourcesÆ in the river basin, show local bacterial reduction or indicate a simple mixing trend. Further isotope analyses including oxygen isotopes of dissolved sulfates will enhance the interpretations.

Jan 1, 2003

By JESSICA W. A. AZURE, Kansake A. Bruno, Samuel Frimpong, AZUPURI G. A. KABA, FORSYTH A. KADINGDI, PROSPER E. A. AYAWAH

Blasting generates undesirable ground vibration with adverse effects on humans, the environment, and structures. Numerous studies have used various techniques including machine learning (ML) to predict the peak particle velocity (PPV) caused by blasting in surface mines. These studies used the validation-set approach to evaluate the performance of their predictive models. In this study, Random Forest (RF), Gaussian Process (GP), and Gradient Boosting Machine (GBM) were applied for the prediction of PPV using data from a large open-pit gold mine in Ghana. An ensemble model based on a stacked generalization approach was then built on these three base models to significantly improve the PPV prediction performance. The model evaluation was done using repeated tenfold cross-validation which resolves the challenges with the validationset approach for small datasets. The dataset used in this study comprised a total of 196 measurements taken from different blasting operations. R-squared ( R2 ), mean absolute error (MAE), and root mean square error (RMSE) were used to evaluate the model performance. The results obtained from these models revealed that all the base models did not significantly outperform each other. However, the stacked generalization approach had a better performance, with RMSE = 0.12, R2 = 0.96, and MAE = 0.07. This approach presented an improvement over the existing methods and will be useful for highly accurate predictions of ground vibration during blast design. The application of this model will be useful for efficient and effective blast design.

Nov 8, 2022

By G. A. Maki, P. J. Fullman, R. G. Roden

"In October 1984, Rocanville Division began using a stacking system to handle potash mill tailings. Previous to this date, mill tailings were slurried to the top of the tailings pile and allowed to debrine while flowing down the pile. With the new stacking system, slurried tailings are fed to mobile stackers. The stackers consist of cyclone packs to debrine the tailings and drag conveyors with screw discharges to deposit the tailings onto the existing pile. This paper deals with the various aspects of the project from conception to its present state.IntroductionPrevious to 1984, when the stacking project was first implemented, potash mill tailings were handled as follows. Mill tailings were first debrined to approximately 65010 solids using a cyclone cluster. The cyclone underflows were then introduced onto a vacuum scroll filter table. Here the tailings were further debrined and discharged into the disposal tank where the tailings were reslurried with reclaim brine and pumped to the tailings disposal site. At the disposal site the slurry was discharged onto the tailings pile and by a natural settling process the tailings were debrined with the brine ultimately collected in the reclaim brine ponds. The shape and profile of the tailings pile was controlled by building salt dykes to control the flow of the discharged tailings slurry. As the tailings pile grew in height, booster pumps were added to the disposal system."

Jan 1, 1990

By P. G. Roden, G. A. Maki, P. J. Fullmann

"In October 1984, Rocanville Division began using a stacking system to handle potash mill tailings. Previous to this date, mill tailings were slurried to the top of the tailings pile and allowed to debrine while flowing mobile stackers. The stackers consist of cyclone packs to debrine the tailings and drag conveyors with screw discharges to deposit the tailings onto the existing pile. The paper will deal with the various aspects of the project from conception to its present state. Key Words: stacking, mobile stackers, Linatex Separators, potash mill tailings, reclaim brine ponds, settling ponds, tailings pile. IntroductionPrevious to 1984, when the stacking project was first implemented, potash mill tailings were handled as follows. Mill tailings were first debrined to approximately 65% solids using a cyclone cluster. The cyclone underflows were then introduced onto a vacuum scroll filter table. Here the tailings were further debrined and discharged into the disposal tank where the tailings were reslurried with reclaim brine and pumped to the tailings disposal site. At the disposal site the slurry was discharged onto the tailings pile and by a natural settling process the tailings were debrined with the brine ultimately collected in the reclaim brine ponds. The shape and profile of the tailings pile was controlled by building salt dikes to control the flow of the discharged tailings slurry. As the tailings pile grew in height, booster pumps were added to the disposal system."

Jan 1, 1986

Queensland Mines Limited operates a small uranium treatment plant at Nabarlek in the Arnhem Land Aboriginal Reserve, some 265 km due east of Darwin. It was the wish of the local Aboriginal people that the ore be treated over an eight year period and that no township be constructed in Arnhem Land. Due to these wish- es it was decided to house employees and their families in Darwin and fly the employees to the minesite for work rosters. A singleman's style camp only was constructed at Nabarlek. To satisfy the Aboriginal people's wishes all recreation time is spent offsite thus lead- ing to a roster system whereby employees spend three distinct periods of 6, 6 and 4 days on- site, broken by recreation periods of 3, 4 and 5 days in Darwin, during each 28 day period. Employees are divided into four opposing rosters, which allows at any given time for approximately half the workforce to be onsite and the other half on rest and recreation leave in Darwin. This method of staffing has generally proved to be most satisfactory although at times problems arise, in terms of both product- ion and social effect not normally encountered when operating within more conventional circum- Stances.

Jan 1, 1984

By L Abrahamsson

This paper describes results from a gender study for a new mine in Pajala, a small community in northern Sweden. Using a gender perspective, the study examines migration, education, local culture, the labour market, and work organisation as problems and opportunities in the regional context for the planned mine. The most obvious ‘gender issue’ for the Swedish mining industry is the very low percentage of employed women, which is even lower among mining workers. To recruit the best people, a company actively needs to attract both women and men; however, the mining companies find it difficult to recruit women as cultural, labour market and educational traditions as well as the mining companies’ own cultures often make it difficult for women to find work in the mining industry.The Torneå river valley, the region surrounding Pajala, has a gender-segregated labour market and gender-stereotyped culture and few young women live in this traditional and oldish region. Many young people leave the region and this is especially true for women. Compared to the rest of Sweden, there is a low educational level, especially among the men. In the mining companies, as in many other male homosocial workplaces, the workplace culture has strong connections to a certain type of traditional masculinity (laddishness, a kind of ‘macho-style’) and for a long time this has excluded women. ‘Gender’, however, is not only a question of recruiting women to a male-dominated industry. An organisation that discriminates according to gender can become inflexible, hindering communication, learning, innovations and change processes. In mining companies, this can manifest itself in hesitant attitudes among the miners about safety as well as organisational and technological development.This study found that companies establishing a presence in this region should develop a strategy for how to deal with and manage the risks and opportunities in the surrounding society (the regional culture) as well as inside the company (the mining culture). This need to be strategic will also be required of future mining companies as they will face higher demands on safety, gender equality, and technology to become modern, efficient and lean organisations.

Nov 22, 2011

By M. Soderstrom

In a solvent extraction (SX) plant, stage efficiency calculations are used to determine mixer efficiency. With modern extractants and mixing equipment, it is generally taken for granted that stage efficiencies will be above 95%, but this is not always the case. Dependant on mixer/solution conditions, stage efficiencies can occasionally be low, therefore leading to higher reagent usage. Proper methods to identify when stage efficiency performance is below expectations, and ways to identify if it is an equipment or chemical issue are valuable tools for a plant metallurgist. With these tools and skills an on-site metallurgist can more quickly return their SX plant to proper operation. This paper will discuss methods for analyzing stage efficiency, evaluating factors that may affect stage efficiency, and evaluating the impact of stage efficiency on the overall operation.

Jan 1, 2010

By Malek Smadi, Yazen A. Khasawneh

"New embankments were constructed mostly on soft clays as part of interstate I69 extension in southern Indiana. The embankments serve as bridge abutments and as part of the fill sections along the interstate extension alignment. The height of the embankments range from 50-ft to 125-ft with a maximum foundation thickness of about 75-ft. The foundation soils comprise relatively high compressible fine grained soils. A fully coupled Hydro-Mechanical numerical simulations were conducted for optimizing the construction stages of the embankments. The objective of the staged construction is to allow for sufficient effective stress and undrained shear strength gain to ensure foundation stability under the stage load. Wick drains were utilized to shorten the drainage path and thus accelerate achieving the required undrained shear strength. The extensive field investigation and laboratory testing programs provided a good understanding of the subsurface conditions and allowed the use of a relatively advanced soil constitutive model in the numerical simulations of the staged construction. The effectively designed instrumentation program allowed for monitoring the settlement and pore water dissipation during construction. The pore water pressure, and surface and subsurface settlements from the numerical model predictions reasonably agreed with the instrumentation data over the construction period.INTRODUCTIONThe stability of soft fine grained foundation soils due to embankment construction is dependent on the undrained shear strength of such soils. The permeability, compressibility, and drainage boundaries control the foundation soils response (settlement magnitude and rate) to loading. The settlement magnitude is a function of minerology and soil structure. The settlement rate which is equivalent to the rate of excess pore water pressure dissipation is a function of the soil permeability and drainage boundary. The dissipation rate control the evolution of effective stress and thus the gain of undrained shear strength. As such, if the increase in total applied load is controlled such that enough time is granted for the evolution of the total stresses into effective stresses, then the stability of the foundation soils is enhanced by the gain of the undrained shear strength. The controlled application of the total stress is the definition of the staged construction. From the definition of the staged construction, it is obvious that the process is a coupling of the hydraulic and mechanical responses of the foundation soils."

Jan 1, 2017

By G. J. Heferen, A. Pranowo, N. J. Aslin, P. O. Eriksson

Glencore Technology (GT) has over four decades experience supplying stainless steel cathode plates (“cathode plates”) to the electro-refining and electro-winning industry. Cathode plates are typically the single biggest capital investment in a refinery. Refineries may view cathode plates as fixed asset or consumables depending on their operational characteristics. This paper examines the issue of cathode plate life and the strategies and philosophies used by different plants in the management of their cathode plate asset. Some plants operate with their original plates after more than 20 years. Others accept high turnover and regular maintenance as normal operating practice. Reference data are provided on plate life for various operating plants including benchmark plants achieving best-practice plate life and operating cost. The role of the electrode handling equipment on cathode plate longevity is also examined, including latest developments in Cathode Stripping Machine, robotic copper stripping, and full-automation production cranes. The ability to identify and manage the population of plates in service is also critical for maximising plate life and minimising its overall operating cost. This paper discusses a novel and unique RFID system for tracking and managing cathode plate inventory. INTRODUCTION Permanent cathode plates The adoption of permanent stainless steel cathode electrodes in the electro-refining of copper was the most significant process development since the first commercial electro-refineries were built in the late 19th century. It provided significant improvement over the labour intensive and complicated starter sheet system. Copper grows over the permanent cathode blade for a number of days before being stripped, and the permanent cathode can be returned straight back to cells for the next cathode cycle. Glencore Technology (formerly Mount Isa Mines (MIM), then Xstrata Technology) has been manufacturing permanent stainless steel cathode plates from the late 1970s with the birth of ISA PROCESS™, and the Kidd process that came one decade later. Invented and commercialised by Mount Isa Mines, the ISA PROCESS™ was first implemented into Copper Refineries Limited (CRL), Townsville, in 1978. The KIDD PROCESS by Falconbridge evolved in the 1980s and was first implemented into the Kidd Creek Tankhouse, both operations converting from traditional copper starter sheets.

Jan 1, 2019

By H Tran

Local communities are undertaking an increased role in mine project decision making processes, associated with growing pressure and expectations from regulators, financiers and the general public. This is particularly evident in international projects within developing economies. Environmental and social issues are often complex. Solutions demand difficult choices and trade-offs between sustainable development dimensions: economic growth, social equity and environmental integrity. Proactive stakeholder engagement can play a critical role in assisting decision-makers in determining the operational reality of sustainable development by jointly exploring project trade-offs between proponents and affected stakeholders. Good stakeholder engagement has other potential benefits, ranging from reduced financial risk due to regulator delays, legal disputes or negative publicity to increasing market share through good public image. Approaches to consultation and disclosure have changed from short-term regulatory based focuses, to longer-term, strategic tools for relationship building, proactive risk management and new business identification. Approaches to consultation form a significant opportunity to contribute to overall social sustainability. This paper discusses, based on authorsÆ experience, the broader concept of stakeholder engagement and its contribution to social sustainability of the mining industry. The focus is on key considerations for an effective stakeholder engagement. Three case studies outline how broad based, proactive stakeholder engagement can contribute to improved operation and overall sustainability. The case studies include: a greenfields project in Ghana; a long-term mine in Australia; and an open-pit mine in Vietnam.

Jan 1, 2009

By R M. Lonsdale, M D. Goodz

"With an ever-increasing dynamic business environment, successful stakeholder engagement is becoming more fundamental to achieving desired outcomes in today’s mineral resource industries. It is imperative to be proactive in correctly identifying all stakeholders and initiating early contact. This builds trust relationships, which are essential to ensure future decision-making processes are streamlined.Often neglected is a company’s obligation to select the correct team to represent its values and mission. The company requires representation that demonstrates an understanding and commitment to its operations and people, the safety and health of the community and environment, and most importantly, represents the decision makers. Stakeholders need to believe that the engagement process is genuine and that the company representatives are aligned towards targeted outcomes that will benefit all stakeholders in some way.Among others, stakeholders include shareholders, staff, families, community, service and supply providers, regulators, land managers and the political/financial framework. Depending upon the mineral product, stakeholders may include ports, international offtake clients and those along the route. New stakeholders continually evolve during mine life, and the engagement process requires an investor–community–public relations (IR/CR/PR) team to anticipate change and actively scan perception and chatter.Successful communication is more than delivering a message; it is about engaging stakeholders and confirming the feedback loop to ensure the correct message is communicated and the relationship is strengthened.The nature of the mining company’s branding and the public’s perception of company intentions will dictate whether there is willingness to allow the company to follow its desired path. This in turn controls the company’s most scarce resource – time. Timing is fundamental to achieving targeted outcomes with minimal cost and delays, marketing in a peak cycle and acquiring critical capital for development and growth.Branding and stakeholder engagement effectively controls and extends to the company its social licence to operate.CITATION:Goodz, M D and Lonsdale, R M, 2016. Stakeholder engagement – who are you, what do you stand for and why? In Proceedings International Mine Management Conference, pp 239-248 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 22, 2016

By S. Schutte, J. Pelders, F. Magweregwede, S. Ngobese, W. Botha

A people-centric, systematic approach that involves different stakeholders is considered necessary to successfully address changes associated with modernizing the South African mining industry. In this paper we discuss the inclusion of various South African mining industry stakeholders, particularly the employees, in equipment design and development processes. Data was acquired through a literature review and inputs from South African mining industry stakeholders through focus group discussions, interviews, and an online survey. It was suggested that some of the areas that could be improved by the inclusion of employees in the process are design quality, ergonomics, equipment acceptance by the workforce, safety, efficiency, skills, insight into context of use, and early design iterations and identification of problems. Among the issues considered to be barriers to inclusion were lack of buy-in, lack of resources, difficulty in manufacturers accessing the mines, difficulties in involving too many people, intellectual property concerns, and unavailability of mine employees due to their key responsibilities. Identified critical factors in the equipment design and development process include iterative design, stakeholder participation throughout the process, needs analysis through consultation, and change management. A guideline was developed for worker inclusion in equipment design and development that could be used by the South African mining industry. The study identified several economic and social benefits of including stakeholders in the early stages of design and development. It is recommended that the South African mining industry considers using the developed guideline.

Apr 5, 2023

By E. H. Henderson

Introduction Stamp-Milling and amalgamation is, perhaps, one of the oldest processes of recovering gold from its ores. Many papers, theses, and textbooks have been written on the subject of stamp-milling practice in general, but, to my knowledge, there have been no publications describing the modern stamp-mill as designed, developed, and operated in Nova Scotia. Although it may be said that the gravity stamp-mill is the most primitive, and perhaps the crudest, crushing machine in existence, it is at the same time the most satisfactory all-round milling and amalgamating device yet contrived. Originating in Saxony, and used in North America first in Virginia and Georgia, the stamp-mill, in a primitive form, later found its way to California and Colorado. Here, it speedily developed from an affair of wood shod with iron, and operated with the crudest gearing, to substantially its present form. Briefly, it consists (see Figure 1) essentially of a series of hammers (the stamps), which fall upon a mixture of ore and water contained in a cast-iron box (the mortar). The resulting crushed ore (the pulp) is splashed out through a screen on the front of the box. For some years after the discovery of gold in Nova Scotia, in 1861, the ? arrastra and Chilean mill were used to recover the gold from the rich ores. The stamp-mill followed, and various types were used, principally the California and Gilpin County types. Then, in 1895, Mr. M. R. O'Shaughnessy, one of our foremost amalgamators, conceived the idea of a new type of stampmill, which has since become standard in Nova Scotia gold mines. This mill, unique in its design and operation, is specially adapted for the most efficient extraction and recovery of gold as it occurs in our Nova Scotian ores. It is commonly known as the Underwater Feed type, as opposed to the usual Overwater or Top Feed type, and it may be rightly termed The Nova Scotia Self-Classifying Stamp Amalgamation Mill. It is conceded by experienced mill-men that it is superior to any other type of mill for recovering the very coarse and granular gold typical of the ores of this Province. The particular installation and practice to be described in this paper is that of the Guysborough Mines, Limited, at Goldenville, Guysborough county. Emphasis will be laid on certain operating innovations of extreme simplicity and high efficiency.

Jan 1, 1935

By Hans S. Carlsson

Like most industrial processes, nuclear power production creates wastes, which have to be handled and ultimately disposed of in a safe manner. Some of the wastes contain very long-lived radioactive substances and have to be isolated for very long periods of time before they have decayed to harmless levels. Sweden, like many other countries with similar geology, intends to use crystalline rock for isolating the high-level nuclear waste from the biosphere. The suitability of a rock mass for a repository needs to be investigated extensively. Apart from the political and practical considerations for a site selection, a detailed study has to be performed in terms of geology, hydrogeology, geophysics, geochemistry and rock mechanics. The responsibility of the site selection studies in Sweden is entrusted to the Swedish Nuclear Fuel Supply Company, Division KBS (SKBF/KBS) . The paper gives a brief presentation of the "Standard Program" for the studies that will be carried out during 1980-1990. Modifications of the program are justified on the basis of gained experience or specific circumstances for each site. The program is compiled by the Geological Survey of Sweden (SGU) in cooperation with KBS.

Jan 1, 1982

By B Ascott

As a prerequisite to achieving integrated regional production reporting across multiple sites, Newmont Australia initiated a project to standardise the configuration and use of mine control systems at three underground sites. This paper outlines the project and considers the outcomes which, in a number of cases, have exceeded the original objectives.

Jan 1, 2008

By S K. Das

An intensive investigation into modern roof support technology, including hy draulic and control systems, has been carried out against the perspective of global development and support behaviour on longwall faces across the Indian sub-continent. The wide ranging study examined various types and designs of modern supports used in seams of varying thickness and inclination where caving and stowing were practised. Consideration has been given to structural analysis, support resistance, the various forces acting over and on the powered supports and to support compatibility. The examination of the phy sical parameters has been allied to field experience and, together, have led to the formulation of standard designs for both the powered support structure and structural systems. A realistic mathematical model has been formulated for calculating the capacity of roof support requirements resulting from the actual behaviour of the immediate roof stratum. As a result of the work, it should be possible to readily select the most appropriate type of support sy stem for the conditions and longwall mining method that is to be employed.

Jan 4, 1997

By R Ulusay

Rock mechanics involves characterizing the mechanical properties and behaviour of rock material and the natural discontinuities of the rock mass, while rock engineering is concerned with specific engineering circumstances, for example, how much load will the rock support and whether reinforcement is necessary. Rock engineering models developed depend considerably on the input data such as boundary conditions, the properties of rock material and rock mass. Correct evaluation of these properties frequently requires laboratory and in-situ tests, supplemented with a high degree of experience and judgment. Accordingly, since 1974, the ISRM Commission on Testing Methods has spent considerable effort in developing a succession of the ISRM Suggested Methods (SMs) for different aspects of rock mechanics and rock engineering with the contribution of a number of working groups and cooperation of some other ISRM Commissions. This paper emphasizes the need and importance of standardization of rock testing methods within the context of the ISRM SMs, gives a guideline for developing ISRM SMs and finally discusses on some implementation and contractual issues associated with rock testing and experienced in practice, and briefly introduces main future trends in rock characterization, testing and monitoring. This is an extended abstract only. CITATION:Ulusay, R, 2018. Standardisation on rock characterisation, testing and monitoring with emphasis on ISRM suggested methods, practical issues and difficulties, and future trends, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 17–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018