Search Documents

By Peter Zhang, Todd Minoski, Gabriel Esterhuizen, Jack Trackemas, Berk Tulu, Morgan Sears

Roof stability in the belt entry is critical for safe and continuous production of coal during longwall mining. Previous studies of roof falls that occurred in belt entries have shown that the roof falls were largely associated with high in situ and longwall-induced horizontal stresses [1,2,3,4]. To properly support the roof in a belt entry, it is important to understand how longwall-induced horizontal stress changes can affect roof stability in the belt entry. Monitoring of horizontal stress changes was conducted in the belt entries of two Pittsburgh seam longwall panels oriented unfavorably to the major horizontal stress. Numerical models were also set up to investigate how horizontal stress concentrates and relieves in the belt-entry roof near the face as panel orientation changes. Both measurements and modeling results show that high horizontal stress concentrates in the belt entry roof within about 15 m outby the face. The study demonstrates that longwall-induced differential horizontal stress can be used to evaluate the horizontal stress concentration factors. The horizontal stress concentration factors change with panel orientation, resulting in high stress concentrations at orientations between 20 and 110° and low stress concentrations between 130 and 180°. Roof support strategies are given for the belt entries under the influence of high horizontal stress. For unfavorably oriented panels in weak roof conditions, supplementary support should be installed during development, and cable bolts should be anchored into a stable roof horizon. The bolting pattern should be designed to cover both entry corners and the entry center to prevent potential roof cutters and sagging.

Jan 1, 2023

By Phil R. Ames, Anil K. Ray, Murali M. Gadde, John A. Rusnak

"Many factors can be responsible for coal mine roof falls including, mining geometry, stress conditions and local geology. In the Illinois Basin coal mines, roof instability is commonly attributed to the low strength of the immediate roof, which is also moisture sensitive. Recently, in order to understand the mechanisms of roof instability, numerical modeling has often been the preferred ground control analysis tool. Since roof materials can exhibit significant spatial variability, such modeling results may not represent every section of the mine. At the same time, it is not feasible to carry out numerical modeling for the full range of geological and mining conditions possible at a mine. Operationally, it is more convenient and highly practical to have a simple map that depicts the expected roof conditions, determined through either complex numerical models or simple empirical analysis throughout the reserve area. In this paper, a case history is presented that shows how a combination of simple empirical analyses of geologic data and past ground control experiences at a mine can be synthesized into a roof stability map, which can then be used to forecast future ground conditions. The usefulness of such a roof stability map will be examined in terms of the predicted and actual ground conditions encountered over a period of more than a year after the map was created.INTRODUCTIONA roof fall, which can result in fatalities and lost work time, is considered to be one of the most severe ground control hazards in underground coal mines. In general, there are many factors responsible for roof falls, including mining geometry, stress conditions and local geology. In the Illinois Basin, roof falls are commonly attributed to the weak nature of immediate roof rocks, and some superficial falls may be initiated due to moisture sensitivity. Some unstable areas also occur when the immediate roof is highly laminated.Numerical modeling is a useful tool used to understand the mechanism of a roof fall by incorporating site-specific parameters. In the past, numerical modeling has been used to explain the mechanism of roof falls as well as simulate· roof falls and cutter behavior, but such work had been strictly site-specific (Gadde and Peng, 2005; Ray, 2009). Because of the restrictions imposed by the input parameters, numerical modeling results cannot represent the entire mine. In the real world, mining conditions vary from place to place, and even in a single panel, modeling results valid at one site may not apply at another nearby site. At the same time, due to the lack of input data pertaining to rock characteristics and in-situ stress variations, it is not practical to carry out numerical modeling for each local area of the entire mine site. In addition to these difficulties, mine operators prefer simple tools to understand the ground conditions at their mine sites. One simple and commonsense based tool is the roof stability map. A stability map not only synthesizes the geologic and stress analysis data empirically, but it can also be used to predict future ground control issues at that mine. Because of this practical appeal, stability maps are more likely to gain mine operators' acceptance and be used in their planning operations. In this paper, a case study is presented on the development of a 'Roof Stability Map' that was principally used for roof fall prediction for a mine in the Illinois Basin."

Jan 1, 2010

By H. L. Teicliman, E. M. Sipprelle

ENACTMENT of Public Law 290 by the 78th Congress authorized the U. S. Department of the Interior, Bureau of Mines, to conduct an experimental program to develop the technology for obtaining oil from oil shale. In adopting and later extending this legislation, the Congress recognized the impending necessity of supplementing ground petroleum reserves with synthetic fuels. Under the provisions of this legislation, the Bureau of Mines, among other things, was charged with the responsibility of developing mining techniques, methods, and equipment for mining the oil shales of the Green River formation of Colorado, Utah, and Wyoming.

Jan 1, 1950

By Thomas P. Mucho

To document the performance of mine roof and roof support systems the U.S. Bureau of Mines (IJSBM) has been installing instrumentation at selected sites in U.S. coal mines. Much of this support and roof instrumentation has been installed in high stress conditions to maximize differences in performance. Summarized in this paper are the results of four such site investigations. The roof geology at the four sites is quite different and is quantified using the USBM's Coal Mine &f Rating (CMRR). The studies included detailed measurements of roof movement using multi-point extensometers, as well as measurements and monitoring of bolt loading. The investigations include developmental loading and abutment loading from longwall and room-and-pillar mining operations. Some of the issues examined are the effect of the horizontal stress field, the effect of installed tension (torque-tension versus resin bolts), the effect of reduced annulus bolt holes, and the differences between similar bolts supplied by different manufacturers.

Jan 1, 1995

By B. Macdonald

In 1991, roofbolts were introduced as a primary support for inseam retreat longwall entries at CBDC's Phalen Colliery. Increasing mine depth (+550 m) necessitated replacing conventional inseam steel sets in these entries because they were being severely damaged during wall retreat and subsequently causing gate end problems. Roofbolts had been used in the Sydney coalfield between 1949 and 1963 in room and pillar working, however, some concerns arose with using roofbolts as a primary support in long (2.2 - 3.4 km) single entry roadways. In order to alleviate these concerns, a phased approach was adopted whereby conventional steel densities remained along with roofbolts. The roofbolt design was such that the roofbolts would be the primary support and the steel sets would experience little or no loading. A detailed geotechnical monitoring program was developed by both CBDC and the Cape Breton Coal Research Laboratories technical staffs. The results of this monitoring were used to build-up confidence in roofbolts and subsequently reduce the steel set densities until eventually only roofbolts were used as a primary support. This paper will discuss briefly the phased introduction of rootbolts at Phalen Colliery and more specifically the development of geotechnical data collection and interpretation.

Jan 1, 1994

By A. R. MacLean

This mine is situated at Point Aconi, Cape Breton , Nova Scotia, and is a replacement for the 100-year-old Princess Collie ry. It is a slope mine which is the continuation of a s trip mine operation. There are fives lopes from the surface driven with Dosco Dintheaders - this marks the first time these machines were used in North America. There are four room -and-pillar sections, each equipped with a Lee Norse HH106 continuous miner, a "Top Dog" roof bolter and two Wagner diesel Teletrams. There are also two Eimco 913 diesel LHD's , which are used for clean-up in the mines. This paper describes the mining operations of this 800,000-tpy mine which, in less than a year and a half , has been developed to the stage where four sections are producing coal at the desired rate.

Jan 1, 1978

By H. J. Bogert

Shallow, gently dipping quartz veins at the Mineral Hill Mine are mined in room and pillar stopes. Ore zones are severely folded and fractured, thus actual pillar strength and physical properties of the rock mass deviate significantly from conventional laboratory tests and pillar theory. Laboratory specimens large enough to include pre-existing fractures proved to be representative of actual pillar strength. Further adjustment for specific pillars was based on RQD. Deformation and stress were measured in several pillars during pillar recovery. Stress data and finite element modeling were used to estimate absolute pillar stress at failure. The stress/strain relation provided an excellent indicator of pillar behavior. Good agreement between lab data and underground data was found.

Jan 1, 1995

By Kotaro Ogura

"Ethylene has been produced in aqueous solution from CO2 by the electrochemical reduction driven by a natural energy. This process is useful for storing a large amount of the natural energy. In the closed system, the conversion efficiency of CO2 is almost 100%, and the maximum selectivity for the formation of ethylene is more than 70%. On the other hand, the current efficiency for the competitive reduction of water is less than 10%. The electrolysis is practicable under such special conditions as three-phase interface consisting of gas, solution and metal, concentrated solution of potassium halide, low pH and copper or copper halide-confined metal electrode. These requirements are thoroughly examined, and the grounds to reply upon are revealed. A series of chemical apparatuses including an electrolytic cell in a large scale are designed for the ethylene production, which allow us continuously to supply raw CO2 and to extract the product.IntroductionIn connection with the depletion of the petroleum reserve, much attention has been paid to the utilization of natural energies such as sunlight, wind force and waves. However, these energies are always changeable, and some means of storing them are necessary for the common use. In general, natural energies are transformed to the electric energy at the time of utilization, but the electricity is not very storable. This is one of the reasons why the application of natural energy is not so expanded. On the other hand, the storing of natural energy by plants is very skilful. In the photosynthesis, solar energy is transformed to chemical energy by fixing carbon dioxide."

Jan 1, 2009

By George Delorme

"AbstractThe basic intention of this paper is to present, from a practical viewpoint, a thorough outline of all the sound and accepted principles connected with attaining satisfactory rope performance from multi-rope friction winders.In order to emphasize the importance of some aspects of rope maintenance, a limited amount of hoist rope theory has been included, a s it is felt that without this, some of the more critical, but nevertheless practical, aspects would perhaps pass without full appreciation of their individual merit.It is very much appreciated that many of the maintenance topics and practices discussed herein are already being observed with a high degree of skill among those already involved in modern friction winding. The hope is expressed, however, that the paper will be of additional assistance, and of particular help in introducing sound maintenance principles to those who are moving into this field of operation for the first time.Hoist RopesWITH a multi-rope friction winder system, structural upset within the hoist rope's cross section can occur if the ropes slip in the drum treads. This upset will usually appear at either end of the rope at the tangent point of the drum or deflection sheave with the respective conveyance in the normal uppermost position. This slipping action on the drum causes the outer cover of a Full Locked Coil or the strands of a stranded rope to shift, leading to structural upset. The result very often means that the ropes have to be withdrawn from service before completing their maximum service potential.The cause of any rope slipping in its tread can be associated with a discrepancy in tension of that rope between one side of the drum and the other."

Jan 1, 1977

By H. Hitchen

THE object of this paper is to present the various facts that l1ave been revealed during lengthy investigations into the performance of all types of ropes on different hoisting installations. It then goes on to suggest means by which most of these findings could be usefully employed to obtain more economical rope lives with increased safety. SHAFT HOISTING ROPES Four basic designs of ropes are now employed for hoisting duties: (1) Six-strand, round strand ropes with fibre cores. (2) Six-strand, triangular strand ropes with fibre cores. (3) Non-rotating, multi-strand ropes. 0) Locked coil ropes. Round Strand Ropes (Figure 1) Very solid and reliable ropes can be obtained with this simple geo-metric design of strand. 1'1?iangula1? Strand Ropes (Figure 2) Owing to the fact that the wires in the strands are bent over a triangle, they do not seat quite so solidly as when they are bent over a circular core wire, as is the case with

Jan 1, 1963

By Richard Addison, Ronald O. Cranor

Tailings dam construction and operation of Rosario Dominicana's gold/silver mine in the Dominican Republic is described. Impoundment of 8.5 kt/d of cyanide-process tailings is required in an intensive agricultural area which is also an earthquake and high rainfall zone. The earthfill embankment dam, incorporating internal gravel drains, is described together with methods of construction used. Methods of tailings transport, solution reclaim, and runoff water diversion that have evolved are discussed.

Jan 1, 1982

By Richard Addison

Rosario Dominicana, S. A. operates an 8,500 tonne per dayopen pit gold/silver mine in the Dominican Republic on the Caribbean island of Hispaniola. The mine is located in an agricultural area which is also an earthquake and heavy rainfall zone. In the 64 years from 1910 to 1974 there were 19 earthquakes within 300 km of the mine in the range of 6 to 8 on the Richter scale and the most recent earthquake in this range occurred in March, 1979. Average annual rainfall in the area is 1.7 m and is distributed throughout the year. Safe and environmentally sound tailings disposal in such conditIons has demanded the buiIding of an extremely strong dam wall and use of a fail-safe system of tailings disposal and solution reclaim. The type of dam, the system of tailings disposal and solution reclaim comprise an interesting example of the manner of handling tailings for a medium tonnage mine. The system is relatively costly but does assure a long-term, safe and trouble free structure and operating system. General views of the dam wall and tailings pond are shown in Figures l through 4.

Jan 1, 1980

By T Ireland

The Rosedale Outfall Project utilised an earth pressure balance (EPB) tunnel boring machine (TBM) for only the second time in Auckland. Although the tunnel was excavated fully through East Coast Bays Formation (ECBF), the downhill gradient along with some unexpected areas of extreme water posed some significant challenges during construction.The Rosedale Waste Water Treatment Plant Outfall Tunnel project was commissioned in response to the growing needs of North Shore City, New Zealand. The outfall tunnel comprises a 3 km long segmentally lined tunnel and a 2.1 km buried marine pipeline, and discharges 2.7 km offshore. The capacity of the new outfall is 6 m3/s compared to the existing outfall capacity of 1 m3/s.Following previous project experience, and with the tunnel located along its full length in the bedrock weak sandstone/siltstone bedrock of the East Coast Bays Formation, tunnelling conditions were expected to be benign. However during construction six high inflow events were encountered, including a full face (3.4 m diameter) of Albany Conglomerate over a 48 m length of tunnel. This material comprised cobbles in an uncemented sand matrix, and inflows were recorded at over 25 L/s.This paper describes the design challenges on the project including the design of a steel fibre reinforced segmental lining for internal pressures. The specification of the machine is discussed including the modifications required to enhance the risk mitigation measures already in place. The ground conditions encountered are discussed and have improved the knowledge of the range of conditions that can be expected in Auckland.Despite the challenges presented during construction, excellent progress rates were achieved and the tunnelling was successfully completed ahead of program.

Mar 8, 2011

By William Gleason

With more than 20 major mines extracting copper, gold, coal, molybdenum and lime, Arizona is recognized as one of the better mining jurisdictions, not just in the United States, but in the world. However, that is not to say the road to production is always paved with gold, or in many cases, copper. Earning the license to mine in Arizona is a complex process with years of paperwork and permitting before the first tons of ore are ever processed. Now, get the federal government involved and the process becomes even more complex, and the path to production can become even longer.

Jan 1, 2013

By Bevan. P. A.

The general location, topography and climate are discussed briefly, together with an historical record of the deposit. General geology, grade control and ore reserves are covered at some length, and reasons are given for the operation being placed on a salvage basis.

Jan 1, 1973

By Carl G. Bock

INTRODUCTION Rapid transit systems involving near surface tunneling in hard rock are becoming more numerous, especially along the northeast corridor of the East Coast. Tunneled systems are under construction in Washington, D.C. and are being planned for Atlanta, Buffalo and Baltimore. Near surface tunneling is defined for this paper as being that in which the crown is 100 feet or less below ground surface. For Rosslyn Station, the total cover ranged from 52 to 70 feet. The rock cover, however, ranged from 40 to 50 feet which is slightly less than the station height and about two-thirds of its width. Rosslyn Station (Fig. 1) is the only station excavated completely in hard rock in the Virginia portion of the 98.5 mile Washington Metropolitan Area Transit Authority's (WMATA) rapid transit system. The station site, oriented in a north-south direction beneath a main thoroughfare and flanked by multistory office buildings, was fixed by the need to serve a dense population center at a specific location and geologic conditions were a secondary consideration in siting. There was no previous underground rock excavation in the Washington Metropolitan Area of the size and scope of Rosslyn Station that offered a practical case history guide to the geologic conditions and excavation problems to be encountered. GEOLOGY The regional geology of the Washington Metropolitan Area is divided into two physiographic provinces by the northeast trending Fall Line (Fig. 2). Northwest of this boundary is the Piedmont Province

Jan 1, 1974

By L Eriksson, D Penn, J Appelgren

Atlas Copco, a leading supplier of equipment and services to the mining and construction industries, is consistently pursuing its strategy to offer the most productive and economical solutions by continuously offering new innovative products. These are, in most cases, developed and tested in close cooperation with demanding end users before being officially launched on the international market. The demands for higher productivity and improved overall economy have resulted in systems for automation of the drilling cycle and also tools for integrating the drilling equipment to the production control system used by the customer. In terms of improving the blasted material quality, the company has placed emphasis on accuracy in the drilling process and documenting what has been drilled. By applying state of the art technology to the common automation platform, developed for the surface drilling market, major steps in improving overall drilling productivity and blasting performance have been achieved. This paper will give some examples derived from the latest development of solutions for the companyÆs surface drilling products.CITATION:Appelgren, J, Eriksson, E and Penn, D, 2012. Rotary drilling automation increasing operator productivity and drilling quality, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 13-18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

Atlas Copco, a leading supplier of equipment and services to the mining and construction industries, is consistently pursuing its strategy to offer the most productive and economical solutions by continuously offering new innovative products. These are in most cases developed and tested in close cooperation with demanding end users before Being officially launched on the international market. The demands for higher productivity and improved overall economy have resulted in systems for automation of the drilling cycle and also tools for integrating the Drilling equipment to the production control system used by the customer. In terms of improving the blasted material quality, Atlas Copco has placed emphasis on hole straightness and the need for hole logging and positioning. By applying state of the art Technology to today?s computerized drilling rigs, major steps in improving overall drilling and blasting performance have been achieved. This paper will give some examples derived from the latest development of solutions for the Rotary drilling product line.

Jan 1, 2010

By Harry Siewert

"The commissioning of the 4th concentrator (C4) at Freeport Indonesia in early 1998 increased total mill throughput from 130k to 230k tonnes per day. The C4 flowsheet consists of a single 38 ft diameter SAG mill, four 24 ft diameter ball mills followed by four banks of 4,500 ft3 WEMCO flotation cells.The design of the C4 rougher flotation circuit was based on the expectation that the copper and gold recoveries achieved with the 4500 ft3 flotation cells would be equivalent to or better than that achieved with the 3,000 ft3 flotation cells in the 3rd concentrator (C3) rougher circuit. This assumption was due to the fact that the C4 flotation feed size would be less than 15% +212 microns compared to the C3 rougher flotation feed size of less than 23% +212 microns. By mid 1998 it had become apparent that the C4 rougher flotation copper and gold recoveries were below those predicted.In order to determine the cause of the lower recoveries, stage by stage rougher flotation surveys were performed in all four concentrators. The results of the surveys showed that the C4 rougher flotation circuit had a lower recovery of +200 micron material than that achieved in the C 1, C2 and C3 concentrators. Through mineralogical analysis, it was determined that a majority of the copper contained in the +200 micron fractions was liberated and recoverable. This paper describes the steps taken to increase coarse particle recovery, overall plant recovery and the results achieved."

Jan 1, 2001

By Raymond E. Sandiford

"The redevelopment of the World Trade Center (WTC) provided an opportunity for the Port Authority of NY and NJ to complete a long sought underground connection between all of Lower Manhattan’s transit lines, the World Trade Center and the World Financial Center (WFC) (Figure 1). Creating this connection was a challenge because the WFC lies west of the heavily trafficked Route 9A, also known as West Street. The previous connection was a bridge that required pedestrians to make significant level and directional changes to navigate the crossing. The positioning and elevation of the Route 9A pedestrian tunnel was established to provide pedestrians with a clear, single level, climate controlled corridor from the new WTC Transit HUB to escalators leading into the WFC Winter Garden.As the most direct link to the WFC, tens of thousands of people a day will use the pedestrian corridor. To accommodate this large number of pedestrians and provide an obstruction free passage, the tunnel has a clear width of 50 ft (15.2 m). Although only 250 ft (76.2 m) long, that short length presented many technical challenges.Here I describe how the challenges were overcome during the construction. However, some of the truly problematic issues arose from coordinating the phasing of this project with adjacent construction activities at the WTC, the reconstruction of Route 9A, and the WFC’s redevelopment program. The limited access to the excavation areas and confined site logistics were further complicated by having to maintain six lanes of traffic on Route 9A at all times. The efforts were so intertwined that, well into the underpass construction, the Port Authority Construction Department decided to merge a portion of that work into the WFC redevelopment."

Jan 1, 2012