Search Documents

By F. P. Hassani, A. Hara, M. Momayez

To be competitive on the international market, the Canadian mining industry must reduce its costs, increase its productivity and maintain a high standard of safety. There is a great need today for improved methods that would allow the detection of geological structures in advance of mining to reduce dilution and the monitoring of underground structures to increase safety. This will facilitate planning for optimum exploitation of the mine and to increase production at lower costs. This paper discusses two examples of more efficient mine planning using new technologies such as Ground Probing Radar (GPR). In Kidd Creek mine, GPR technology was used at the 2500and 2600 levels to (1) monitor the stability of the sill pillar; (2) locate the presence of disseminated sulphide pockets in the sill pillar for extracting the mineral content; (3) monitor the stope backs and wall structures to evaluate the effect of on-time filling sequences; and (4)assess rockfill quality in terms of the presence of voids and fractures within the rockfilled areas. In the New Brunswick coal mine in Minto, GPR was used along with core log data to map and construct a 3D block of a section of the bench showing the relative position of different layers overlying the coal seam.

Jan 1, 1996

By V O’Brien

The suitability of magnetic surveys flown at low altitudes to identify buried heavy mineral (HM) strands has long been accepted. This is despite the low intensity magnetic response often obtained from such strands. The fundamentals of the magnetic survey method dictate that the closer the instrument is to the source the stronger the response. As such the optimal elevation for the magnetometer is at or near the surface. Iluka sought to use a ground based magnetometer to aid in the exploration target generation process and allow accurate targeting of exploration drill holes. Following the initial trial Iluka recognised the potential additional application of data obtained by a ground based magnetometer over known strand deposits. The detail of the ground magnetic images can confirm the assumed strand continuity between cross-sections of close spaced drilling and can aid in the definition of the geometry of different generations of mineralisation. The ability to confidently determine that the deposit has not been truncated by post emplacement erosion of the mineralised deposit may enable reductions in drilling requirements as well as assisting mine planning activities. Iluka intends to investigate advanced modelling of the magnetic data to determine the level of strand geometry and HM content resolution that can be achieved from the ground magnetic survey data and its potential application in the mining grade control process.It is anticipated that the surveying of Iluka’s known resource deposits will provide the ability to correlate the magnetic response from new exploration targets with those from known deposits for a given depth, HM grade and mineralogy suite.

Oct 5, 2011

By William D. Monaghan, Michael A. Trevits

Over the period 2000 to 2003, roof falls have accounted for 4 to 14% of the fatalities in underground mining operations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the frequency, exposure, and risk of these events through an ongoing program of field and laboratory studies. One area of research involves the evaluation of polyurethane grouting technology that is commonly used to stabilize fractured mine roof strata. Concurrently, NIOSH is conducting work to evaluate the application of ground penetrating radar for advanced delineation of problematic mining areas. In this study, NIOSH partnered with Sub-Technical, Inc. who injected a polyurethane grout (also known as glue) into a roof area of NIOSH’s Safety Research Coal Mine. The mine roof area was scanned using ground penetrating radar technology before and after grout injection in an attempt to determine the extent of grout infiltration. A comparison of the pre-and post-grouting radar records showed a significant change at a mine roof depth of about four to five feet. The interpreted radar records were then compared with drill core information, borescope evaluation of roof-bolt holes in the study area, and underground observations. At this site, the interpretations of the radar records correlated with data obtained from the core holes, borescope evaluations and underground observations. This study showed that ground penetrating radar technology can be a useful tool for detecting changes in mine roof due to the injection of the grout.

By William Monaghan

Over the period 2000 to 2003, roof falls have accounted for 4 to 14% of the fatalities in underground mining operations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to reduce the frequency, exposure, and risk of these events through an ongoing program of field and laboratory studies. One area of research involves the evaluation of polyurethane grouting technology that is commonly used to stabilize fractured mine roof strata. Concurrently, NIOSH is conducting work to evaluate the application of ground penetrating radar for advanced delineation of problematic mining areas. In this study, NIOSH partnered with Sub-Technical, Inc. who injected a polyurethane grout (also known as glue) into a roof area of NIOSH's Safety Research Coal Mine. The mine roof area was scanned using ground penetrating radar technology before and after grout injection in an attempt to determine the extent of grout infiltration. A comparison of the pre-and post-grouting radar records showed a significant change at a mine roof depth of about four to five feet. The interpreted radar records were then compared with drill core information, borescope evaluation of roof-bolt holes in the study area, and underground observations. At this site, the interpretations of the radar records correlated with data obtained from the core holes, borescope evaluations and underground observations. This study showed that ground penetrating radar technology can be a useful tool for detecting changes in mine roof due to the injection of the grout.

Jan 1, 2004

By J Karlovšek

Civil engineering infrastructures are often subjected to different types of natural and mechanical activities. These influences may result in serviceability or even in stability of structures due to material deformations, increased water content within the materials used or the formation of internal or adjacent cavities that may threaten the infrastructure. Construction practices can lead to development of such defects in the form of cavities. In civil engineering it is crucial to detect these variations in material properties and to detect the presence of defects. However, as they are often hidden from view, these attributes may be difficult or impossible to target with traditional testing methods. For these reasons rapid geophysical methods, such as ground penetrating radar (GPR), are increasingly being used. At the University of Queensland (UQ) GPR is used for detection of voids and cavities which have been caused by an over excavation of the earth pressure balance machine (EPB) operating in a closed mode.A variety of numerical simulations using the finite-difference time-domain (FDTD) methods and preliminary experiments have been carried out in order to specify information about the nature, type, size, location and other characteristics of targets to be detected by GPR. In doing this the difficulty of interpreting GPR data, which is mainly due to the complexity of the factors involved in multiple possible solutions of the observed features, can be overcome.

Mar 8, 2011

By S C. Dominy, R C. A Minnitt

Determination of the sampling constant and liberation diameter are of importance when applying the Fundamental Sampling Error (FSE) equation to optimise sampling protocols. The method for the direct determination of the sampling constant is based on the æGy 50-pieceÆ experiment and variants thereof, which is generally known as the heterogeneity test. In the coarse gold environment, the heterogeneity test is prone to poor repeatability and bias due to the very heterogeneity that it aims to quantify. A key issue is the large sample mass that can be required in the coarse gold environment, which may reach 1 t or more. The heterogeneity test often provides an evaluation of the background gold grade heterogeneity, but understates that of the high-grade coarse-gold component. This is because the total mass of fragments is usually too small to represent the mineralisation. Despite this relatively well-known problem, heterogeneity tests are often undertaken on deposits where the presence of coarse gold is ignored, not fully realised or vastly understated. Sampling types and protocol designs are frequently based on poor quality data that do not match the characteristics of the orebody. For this style of mineralisation, an empirical approach to define ore characteristics is recommended.CITATION:Dominy, S C and Minnitt, R C A, 2012. Application of heterogeneity testing to coarse gold ores, in Proceedings Sampling 2012 , pp 143-160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By David Morrow

Fly ash is a by-product from coal-fired power stations that is captured from the exhaust gas stream by electrostatic precipitators (ESPs) or bag houses. It is mainly derived from the inorganic components in coal but also contains residual carbon from unburnt fuel (measured as LOI). In the past, nearly all fly ash was sent to landfills or tailings ponds by power generators but this trend is quickly changing due to landfill costs, sustainability requirements and the inherent value in correctly processed fly ash. The main property that makes fly ash suitable for recycling is its use as a pozzolan. Pozzolans exhibit cementitious properties that make them suitable for partial cement replacement, and that can have beneficial properties for concrete mix designs. Fly ash can be used to replace up to a third of the of the Ordinary Portland Cement (OPC) requirement. Suitable fly ash nearly always requires the removal of the less reactive coarser fraction from the finer fraction. Due to the pozzolanic nature of fly ash, it must be processed dry and separation is normally required at 45 micron. In response to the increasing demand from a range of dry classification applications, Metso purchased an established air classification technology suitable for both mining and construction applications. The classifiers intelligent design efficiently utilizes the air flow which keeps power requirements low whilst including a scrubbing/recirculating function within the classifier that allows extremely efficient separations even at very fine sizes. This technology is of global interest to Fly Ash processors, but should be of particular interest in India which is both the second largest cement producer in the world as well as producing 80% of its power from thermal sources. This paper is intended to give a brief overview of fly ash and requirements for use as a pozzolan, air classification of fly ash and a case study from an established and experienced fly ash producer. Keywords: air classifier, fly ash, pozzolan, fineness, cement, cholla, salt river materials group

Sep 1, 2012

By J. Bilant, B. Carlson, N. Gow

High Pressure Grinding Roll (HPGR) technology has been evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester, Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data was consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8%, from 61% to 69%, and shorten the overall timing of silver recoveries from 20 years to just over two years. INTRODUCTION The Rochester mine, and associated valley fill heap leach facilities is an open-pit silver and gold mine located in Pershing County, Nevada, approximately 26 miles northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7M troy oz silver (Ag) and 51k troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8” ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers. Historical recovery rates of crushed Rochester ore average 61.4% Ag and 95.9% Au over a period of 20 years [1]. These rates were derived from third party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher, and/or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact of HPGR technology to metallurgical recovery and heap leach performance of crushed product in an open circuit configuration, as a potential replacement for the currently in place tertiary cone crushers. During these years, HPGR was evaluated in three phases of test work.

Jan 1, 2019

By J. Bilant, B. Carlson, N. Gow

"High-pressure grinding roll (HPGR) technology was evaluated to replace tertiary cone crushing at Coeur Rochester operations (Coeur Rochester Inc.) as an opportunity to improve silver recovery. In 2016 and 2017, onsite and third-party pilot programs were initiated to evaluate the impact on metallurgical recovery and heap leach performance of crushed product generated by an HPGR. In 2018, Forte Dynamics evaluated the HPGR laboratory metallurgical data from Coeur Rochester and all third parties to develop field-scale leach curves based on new crushing scenarios. The laboratory recovery test work data were consolidated and scaled to field conditions to determine projected heap leach performance. Based on the metallurgical testing conducted, the replacement of current tertiary cone crushers with HPGR technology has the potential to increase Coeur Rochester’s silver recovery rate by 8 percentage points, from 61 percent to 69 percent, and shorten the overall timing of silver recoveries from 20 years to just more than two years.The Rochester Mine, and associated valley fill heap leach facilities is an openpit silver and gold mine located in Pershing County, NV, approximately 42 km (26 miles) northeast of the city of Lovelock. In 2017, Rochester produced approximately 4.7 million oz silver (Ag) and 51,000 troy oz gold (Au). Ore mined at Rochester is either fed directly to the primary X-Pit crusher, crushed at an in-pit crusher system, or placed directly onto a heap leach pad as run-of-mine (ROM). Both crushing circuits are comprised of three stages of crushing to produce a nominal 3/8 in. ore. Primary crushing consists of jaw crushing while secondary and tertiary crushing are composed of varying cone crushers.Historical recovery rates of crushed Rochester ore averaged 61.4 percent Ag and 95.9 percent Au over a period of 20 years (Robinson et al., 2018). These rates were derived from third-party verification of in-house metallurgical test results, crusher production and heap leach production results from 1986 through 2004 in a private report for Rochester produced by KD Engineering Co., Inc. Recovery rates are regularly verified by compositing daily samples of ore delivered to each leach pad from the X-pit crusher, in-pit crusher and/ or ROM. A proportionate split of each sample is used to generate monthly composites for metallurgical analysis utilizing column leaching and bottle roll leaching. These tests are run in a manner analogous with production conditions and deliver test results that provide expected heap leach performance. As the Rochester oxide deposit has been mineralogically and metallurgically consistent, the gold and silver recovery trends have also been consistent over the life of the project."

Sep 1, 2019

By J Cook, S Pike, D Pridmore

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The application of high-resolution seismic reflection to map structure and/or mineralisation in hard rock environments has progressed significantly in the last decade. Improvements in equipment, field practice, processing and understanding has seen the seismic reflection technique emerge as a cost-effective tool for high-resolution three-dimensional structural and lithology mapping to depths far greater and with superior accuracy than other more conventional geophysical techniques.This paper outlines results and preliminary interpretation of 2D and 3D seismic reflection surveys aimed at defining fault zones and locations for quartz load development in favourable host lithologies at the Cracow low-sulfidation epithermal gold system in Queensland, Australia.As this is possibly the first time that high-resolution seismic reflection data has been used to define the structurally-controlled location of low-sulfidation epithermal gold mineralisation, an important aspect of this work was the derisking or due diligence steps taken prior to commissioning the full 3D surveys at each site. This included full wave sonic logging, vertical seismic profiling and trial 2D lines. Interpretation of the 2D profiles and the drilling of interpreted structure provided the confidence to proceed with the full 3D survey.The advantage of collecting 3D data extends beyond ensuring that the received reflections are located correctly in 3D space. The final 3D data cube can potentially map the entire fault network, thus highlighting flexures and changes in orientation of the structures both vertically and along strike, which is an important aspect in the deposition of gold and for direct targeting.CITATION:Smith, R, Cook, J, Pike, S and Pridmore, D, 2015. Application of high-resolution seismic reflection surveys to exploration for blind vein systems at the Cracow low-sulfidation epithermal field, in Proceedings PACRIM 2015 Congress, pp 77–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Takashi Sasaoka, Pinyo Meechumna, Hiroshi Takamoto, Pipat Laowattanabandit, Akihiro Hamanaka, Kikuo Matsui, Hideki Shimada

"The EGAT Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 million tons of lignite annually to generate 2,400 mw of electricity. The surface mine pit covers is 4 by 7 km (2 by 4 mi) with mining depths ranging up to 260 m (853 ft). A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope often occur due to weak planes, such as faults and bedding, and the weak mechanical properties of the rocks. Hence, a 200-300 m (656-984 ft) boundaries of rock block including coal seams is left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope.The focus of this paper is on the applicability and design of the highwall mining for recovering much of the coal left along the pit slope.INTRODUCTIONThe EGAT Mae Moh Mine is located about 630 km (186 mi) north of Bangkok, Thailand (see Figure 1). It is the largest coal mine in Thailand and produces about 16 million tons of lignite annually from open-cut mining (70 % of the total coal produced in Thailand). The coal is used to generate 2,400 mw of electricity at the Mae Moh power plant, which is situated near the mining area. The mine pit covers an area of 4 by 7 km (2 by 4 mi) at varied depths up to 260 m (583 ft) as shown in Figure 2. As the mining operation progresses, the pit becomes to be deeper and deeper. In the year 2035, the bottom of the pit is expected to reach depths of 500-600 m and the open-cut mining operation will be finished. The possibility of an underground mining operation is being investigated.A large pit slope is formed with the progression of open-cut mining. However, massive slides often occur in the pit slope along weak planes including faults and bedding planes due to the weak nature of the rock. As a result, 200 to 300 m (656 to 984 ft) boundaries of rock including coal seams are left in place in front of faults to prevent slides and to maintain the stability of pit slope. Moreover, the dip of the slope is less than that of the planned design. As a result, there significant coal reserves abandoned along the pit slope."

Jan 1, 2010

By I M. Platten, S C. Dominy

The evaluation of historical goldfields is currently topical, reflecting a high gold price, improvements in knowledge and technology. and lack of greenfield sites. Many goldfields comprise narrow gold-quartz veins which are structurally complex with an irregular distribution of gold; variable geometry and architecture; and display late deformational effects. The study of historical mine records can be an important tool during early and advanced project evaluation since it contributes to understanding the orebody, exploration target size and setting expectations. The historic Engineer Mine property is located 32 km west of Atlin, British Columbia on the east side of Tagish Lake. The economically important Engineer and Double Decker veins belong to a NNE-SSW vein set. These are narrow, commonly <2 m dilational veins with a minor sinistral strike component and of an epithermal type. Documented ore production between 1910 - 1952 is recorded as approximately 14 263 t at 39.4 g/t Au and 19.5 g/t Ag (for 18 000 oz Au and 8950 oz Ag). The underground workings consist of about 5500 m of tunnels, shafts, raises and stopes over eight levels. The mine is currently being re-evaluated. In 2011, an Inferred Mineral Resource of 41 000 t at 19 g/t Au for 25 000 oz Au (at a 5 g/t Au cut-off) was defined from historical data supported by modern drilling into the Engineer and Double Decker veins. A surface and underground bulk sampling and milling program was undertaken in 2011.CITATION:Dominy, S C and Platten, I M, 2012. Application of historical data to estimate a mineral resource at the Engineer gold mine, British Columbia, Canada, in Proceedings Narrow Vein Mining 2012 , pp 81-100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Shichang Liu, Hongli Jia, Zhaolian Wang, Maotang Liu, Ltd. Shandong Huate Magnet Technology Co., Fengliang Liu

"Introduce and promote a latest technology and equipment for magnetite. It’s featured of purifying concentrate, lowering tailing grade, high concentrate recovery rate and stable operation. HUATE® New Style Elutriation Electromagnetic Separator is an equipment to obviously upgrade magnetite. The slurry is fed into separation area through feeder. Generated by excitation coil, the working magnetic field distributes specially in separation area. Under the combined effect of the background field, excitation and demagnetic field and gravity, the mineral particles float downwards in the form of magnetic chains, and interact with the rising water. The gangue, non-magnetic particles, lean intergrowth,etc will be discarded as tailing via overflow tank and pipe. While the magnetic will be discharged from concentrate pipe. Its grade is 2%-10% higher than that of traditional magnetic separation equipment. It adopts the technologies of transformer oil cooling, alternative and uniform pulsation magnetic field controlling the tailing grade, larger drum feed-in device, more uniform umbrella scattering discharge and stabler output current, and realizes lower coil temperature raise, stabler magnetic field, more uniform discharge, effective isolation of weak-magnetic area from non-magnetic area, more obvious upgradation and recovery rate and lowering tailing mFe%. It’s more suitable to purify and thicken the high grade and ultrafine iron powder. Compared with traditional elutriation equipment, it adopts new technologies in removing impurities, operation, large-scale, process simplification, water-saving, remote control, etc. It optimizes the comprehensive beneficiation index, expands its application scope, reduces resource wastes and increases economic benefits.INTRODUCTIONMagnetite accounts for a comparatively great proportion in various iron resources. As it’s a kind of strong magnetic mineral, we must adopt the weak magnetic separation equipment in magnetic separation process to realize removing Si and lowering impurities. While it cannot do very well to use the common weak magnetic separation equipment in the final cleaning to remove Si and lower impurities. At present, the plants, adopting single magnetic separation process to realize cleaning and removing Si and lowering impurities, are in the minority. Most magnetite plants adopt the flotation separation process to remove Si, lower impurities and purify the concentrate. Though with stable indexes and high Fe recovery rate, the flotation process is very complicated, high-cost and with lots of environmental pollution. If adopting the weak magnetic separation equipment can realize removing Si, lowering impurities and the final cleaning, the magnetic separation process should be the primary choice."

Jan 1, 2016

By Baochun Wang, Hongli Jia, Zhaolian Wang, Fengliang Liu

"Promote and apply a new beneficiation technology and equipment effectively processing the refractory and medium-fine grained weak-magnetic minerals. HUATE® Forced-oil Cooling Vertical Ring WHIMS adopts the transformer oil cooling technology to cool excitation coils, solving the easily generated scaling problem resulting from water cooling, thereby to eliminate the demineralized water system. With <25 temperature ?raise, its magnetic field is stable. Wrapped by outer magnetic armor, it can generate a background intensity 1360kA/m. It effects very well in 1) wet preseparating the weak-magnetic coarse grains, like hematite, manganese ore, ilmenite, and purifying the concentrate; 2) removing the ferrous impurities and purifying the non-metallic minerals, like quartz, feldspar, kaolin; 3) enriching and recovering tailings from non-ferrous metals, like copper, lead, cobalt, molybdenum, thereby to greatly improve the mine resource utilization. It has applied 14 relative patents in China, and the invention patent in 56 countries, like Russia, USA, Australia, via PCT international organization. HUATE® WHIMS has been applied and accepted in more than 100 mines in and out of China. Compared with water cooling vertical ring WHIMS, it’s energy-saving and water-saving, and avoiding generating the scale. While compared with JONES WHIMS under the same separation indexes, it’s featured of more space-effective, lighter, lower costs, higher gradient, higher efficiency, larger processing capacity and wider grain application scope. Greatly promoting development of mineral processing technologies, HUATE® WHIMS is the equipment to reduce costs and improve efficiency urgently needed by the mine enterprises now.INTRODUCTIONAt present, influenced by the price and production factors, the international market demand for the grade of iron ores is increasing continuously. Restricted by the ore occurrence state, the beneficiation technology level and product economic value, every year the stope strips the stockpiling and discards hundreds of millions of tons of waste rocks containing iron, especially the weak magnetic hematite and limonite with <20% Fe%. The utilization technological bottleneck of these waste rocks makes their concentration ratio as high as 5-6, which leads to the huge wastes of energy, materials and beneficiation reagents and the increase of production costs. The effective solution is to improve the selected Fe% of the waste rocks like hematite. With the successful application of HPGR technologies in Chinese large iron mines, the mill feeding size has been reduced to 6-0 mm or 3-0 mm from the original 15-0 mm in the crushing system with 3 stages of crushing and 1 stage of closed circuit. This creates the conditions for the wet separation and recovery. While for the medium-fine grained weak-magnetic minerals, it lacks of the effective separation and recovery equipment in the world, which’s badly in need of R&D of the medium-fine grained high gradient wet strong magnetic preseparation equipment."

Jan 1, 2016

By H. A. F. de Souza, Dana S. Mills, P. E. Burgener

"ICP-MS has moved from a laboratory curiosity to a functional analytical tool. This paper discusses how ICP-MS has been used to solve difficult analytical problems encountered when analyzing various mine materials. Comparisons between analytical techniques applied to the analysis of gold and the platinum group metals illustrate the advantages and problems of ICPMS when. applied to trace levels of some metals iri the presence of ore grade metals. Interferences and matrix effects are compared to ICP, AA and Neutron Activation. The necessity to select chemical extractions which are compatible with ICP-MS are also discussed.The ICP-MS techniques explained in the examples on Au and precious group elements (PGE) have validity in analytical problems encountered in testing of trace metals in the presence of major elements found in mine materials. Exploration and environmental testing are other areas that require the same analytical approach to quantify trace levels in the presence of major interfering elements normally associated with mining environments."

Jan 1, 1999

By J. C. Stankus

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concerns for the Mine Safety and Health Administration (MSHA) and ground control engineers. During past two years, Keystone Mining Services, LLC designed and developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents the patent pending impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development, and laboratory testing of a water proof composite impact resistant lagging panel, and (3) impact resistant steel set design based on Law of Conservation of Energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By J. C. Stankus, K. J. Ma, D. Faulkner

To protect mine personnel and moving equipment at underground roof fall areas, mine operators typically install steel sets, which are covered with wooden blocks and backfilled with an expanding-type cement material. In large roof falls, the cost of void backfilling becomes prohibitively high, causing some mines to leave the voids open. However, the durability of wood over time and the capability of the steel set and wood lagging to resist falling rock are unknown. This has caused concern for the U.S. Mine Safety and Health Administration (MSHA) and ground control engineers. During the last few years, Keystone Mining Services, LLC developed various impact-resistant steel set designs that were approved by MSHA and installed in various underground fall rehabilitations. This paper presents an impact-resistant steel set design methodology, including (1) steel set design per AISC national standard, (2) design, development and laboratory testing of a waterproof coated impact-resistant lagging panel and (3) impactresistant steel set design based on the law of conservation of energy. Two underground cases will be included detailing the application of the system.

Jan 1, 2011

By S Pontual

The use of spectral data has traditionally been for obtaining mineral information and for mapping out alteration systems. The output from these data is typically in the form of mineral assemblages and data on relative proportions of minerals. However there is much more than just mineral information in the spectral data. Most importantly, the data allow the user to obtain vital information on mineral chemistry for some key alteration minerals. The mineral chemistry data allow the users to evaluate multiple phases of alteration of the same key mineral species, and to assess which phase is related to mineralisation. Mineral indices can be extracted from the spectral data and plotted to represent variations in the chemistry and relative proportions of key mineral phases as downhole, section and three-dimensional (3D) plots. These data can also be compared with the spatial distribution of the mineralisation by integration with geochemical and logging data. Through spatial and statistical evaluation the mineral information obtained using spectral analysis can provide vital information to assist in building alteration models and therefore improve targeting for further drilling and exploration.

Aug 22, 2011

By Gang Guo, Zhong Liu

"In response to an increasing demand of anchored structures for underground space and transportation infrastructure in China, an innovative underreamed ground anchorage system was created. The novel anchorage system has provided more efficient functions with higher capacity at lower cost, because of the enlarged cylindrical body (known as ECB) sealed in capsule at bottom of anchorage. This paper presents the detailed structure of innovative anchorage system and its special features. To investigate the bearing mechanism of new anchorage, we evaluate its performance and failure mode based on the experimental results, and also indicate its strain-hardening load-displacement relationship. Unlike the shaft anchorages, it is identified no overall failure to be found in soil surrounding the underreamed anchorage. More importantly, the anchorage capacity is governed by the base resistance, which takes more than 80% of total pullout capacity resulting from the contribution of ECB. Finally a case history of anti-floating project introduces the new combined construction approach and procedure, which has provided the contribution to the quality control and cost efficiency.INTRODUCTION AND BACKGROUNDThe construction boom over two decades in China has resulted in an increasing demand for underground space and slope stability. The infrastructures market requires the more efficient anchorage systems for retaining structures, resisting uplift forces and slope protection. The major concern focuses on gaining higher capacity and lower cost resulted from perfecting anchorage systems. There are three main anchorage systems designed to achieve the above objectives: ? single bore multiple anchorage system (Barley 1997), ? regroutable anchorage system (Smoltczyk 1991), ? underreamed anchorage systems (Xanthakos 1991). Generally, the concept ? comparing with the other two, can be more competitive due to its distinct advantages. To improve the performance and durability of ground anchorages under the complex geological conditions and diversified engineering requirements, a number of different underreamed anchorage technologies had been used, which included cone - shape anchorage described by Liao, Wu and Shu (1997) in Taiwan, Soilex anchorage developed in Sweden (Massarsch et al. 1997), Soletanche anchorage proposed in France, blasting anchorage used in Czechoslovakia (Hobst and Zajic 1986), jet-grouting anchorage innovated in Europe (Anon 1988), as well as deep mixing anchorage created in Japan (Cheng et al. 2000).The underreamed anchorage systems have the remarkable advantages compared to the shaft anchorage system. However, there are also some weaknesses inherent in the underreamed systems. For instance, the mechanical underreamed anchorage is unsuitable in sand or waterbearing ground, because the enlarged hole is easy to collapse, and it is hard to ensure the quality of anchorages. On the other hand, relying on the blasting in deep hole, the geometrical space and dimension of enlarged hole is uncontrollable, meanwhile, the continuous blasting operations may easily cause the serious ground deformation and the negative effects to the completed anchorages."

Jan 1, 1900

By Turker Hudaverdi, Yasar Agan

This study tries to predict blast-induced flyrock using intelligent modelling techniques. Flyrock is a site-specific phenomenon. Design variables and rock properties highly influence flyrock throw distance. Site investigations were conducted in a sandstone quarry. Fundamental operational parameters, blast dimensions, bench face condition, and rock mass structure were monitored. Stepwise regression technique was applied for variable selection. Burden–hole diameter ratio, in situ block size, and powder factor were determined as the most significant parameters. Considering output of stepwise regression, artificial neural network, ANFIS, and Gaussian process regression techniques were applied to predict flyrock throw. A comprehensive validation was performed using twelve different performance indices. Pre-determination of input parameters supported development of successful soft computing applications. Rock block size was found to be an appropriate input variable for flyrock modelling. In addition to classical performance indices, standardized and symmetric accuracy metrics were quite useful in model validation process. The intelligent models predict flyrock range with an error less than 6 m. The mean percentage errors are lower than 10%. ANFIS seems to be the best model for flyrock prediction. The calculated mean absolute error is 5.36 for ANFIS model.

Nov 12, 2023