Search Documents

By J. K. Richmond

This is a progress report summarizing more than 5 years of a long-range Bureau of Mines research program. The purpose of this program has been to investigate the fire and explosion properties of Green River oil shale in the Bureau's Experimental Mine, in laboratories, and in the field. The lean limits of explosibility of oil shale dust, by small-and large-scale tests, are reported as a function of grade, ignition source, and particle size. A limited number of laboratory tests on the autoignition of oil shale dust layers and the spontaneous combustion tendencies of oil shale are described. Moderate-scale rubble fire tests were conducted to determine flame spread rates as a function of ventilation flow. With the aid of a system to continuously monitor methane emissions in a deep oil shale mine, the characteristics of the methane flow are reported as a function of ventilation and blasting procedures, and are compared with gas yields from core samples. Tentative predictions as to the emission of the methane to be expected in deep oil shale mines, far from the outcrop, are offered. Brief reference is made to a parallel investigation into the fire and explosion hazards of oil shale mining and processing by a Bureau contractor; detailed results of the latter investigation are to be found in the contractor's reports.

Jan 1, 1982

By Siavoljub D. Maksimovic

The Bureau of Mines, through a cooperative agreement with Duquesne Light Co. of Pennsylvania, field tested a method of using pneumatic stowing of crushed limestone to construct seals in long-abandoned mine openings that were part of an active mine closed shortly before sealing. A total of 13 openings at 11 sites were backfilled. In pneumatic stowing, material is conveyed through a pipeline and into the mine opening under low air pressure. The stowing equipment consists of a power sup-ply, a blower, a feeder to inject material into the pipeline, and a nozzle for directing the placement. Material is ejected from the nozzle at high velocity, creating a high-compaction fill upon impact. The fill material used was well-graded limestone aggregate up to 1-1/2 inches in diameter, with sufficient fines. This fill was modified at five locations by the addition of portland cement, expansive cement, and/or bentonite. The pneumatic stowing method is safer and faster than conventional methods, is cost competitive, and eliminates or reduces the exposure of workers to possible hazards since the nozzle can be kept outside the mine opening. The equipment is mobile, but some modifications in the technique would improve performance. The technique was used at remote locations where other methods could not be used without disturbing the environment.

Jan 1, 1982

By Theodore L. Turner

This Bureau of Mines report describes calcination of kaolinitic clay in a direct-fired 2-1/2- by 24-ft rotary kiln at 750° and 775° C. Methods for preparing kaolin feed materials and characterization of calcined products are discussed. Approximately 99 pct of the alumina in a typical eastern Georgia kaolin was soluble in HC1 after calcination at either 750° or 775° C.

Jan 1, 1982

By Annie G. Smelley

As part of its program to develop technology that will encourage maximum utilization of the Nation's mineral resources, the Bureau of Mines conducted research on debrining potash-clay waste slurries by means of flocculation with a high-molecular-weight polymer and subsequent solid-liquid separation on a rotating trommel screen. In laboratory batch tests, potash-clay waste slurries were consolidated from initial clay contents of 8 pct to final contents of 30 pct with a polymer dosage of 1.2 Ib/ton of dry clay waste. Small-scale continuous tests yielded debrined products containing 20 pct solids using a polymer dosage of 1 Ib/ton of dry clay solids.

Jan 1, 1983

By Meherwan C. Irani

The Bureau of Mines is developing a new technological approach to handling the problems of fires in abandoned coal mines and waste banks. This new technology involves the accelerated combustion of "waste" coals in place (i.e., in situ) under controlled exhaust ventilation conditions, which allows for total management of the combustion products; including utilization of the heat produced" This new concept could significantly lower the costs of reducing the environmental and public safety hazards associated with waste coal fires, and could lead to the conversion of a coal waste to a coal resource. The controlled burnout technology has progressed from the laboratory stage to a full-scale field evaluation stage at the site of an abandoned-coal-mine fire. This first report describes the site selection, evaluation, and preparation, and the design and construction of the full-scale controlled burnout installation. Subsequent reports will deal with the results of the operational field trial.

Jan 1, 1983

By M. M. Wong

The Bureau of Mines, under a cooperative research program with four lead companies, has investigated a nonsmelting process for the production of lead metal. The process, which would eliminate sulfur dioxide generation and minimize particulate lead emissions, involves ferric chloride leaching of galena concentrate to produce lead chloride, followed by molten-salt electrolysis of the lead chloride to yield lead metal and chlorine. This chlorine is used to regenerate ferric chloride in the leaching solution. The process was tested in an experimental unit with a capacity of 500 lb of lead metal per day. The tests were performed in three 10-day and six 5-day campaigns, during a period spanning 28 mo. The study was carried out using a southeastern Missouri lead concentrate. Typical lead recovery was about 98 pct. Process problems related to impurity buildup and control were studied. When copper and silver impurities were removed from the leaching solution, a lead metal purity of 99.999 pct was obtained. Lead-in-air levels and lead-in-blood levels of operating personnel were monitored. The process has potential for producing lead with minimum pollution, but is not ready for commercial utilization. Operation of a prototype commercial electrolytic cell and a full-scale pilot-plant investigation by industry are needed to evaluate the commercial viability of the process.

Jan 1, 1983

By R. S. Olsen

Although aluminum is easily leached from calcined clay with boiling mineral acids, the presence of fines and slimes in the leached residue has hindered the application of acid leaching processes. A feed preparation method was, therefore, devised that provided a dense, smooth-surfaced, fine-grained clay. The important factors affecting feed quality were determined to be (1) crushing the raw clay to the size desired for the leaching process, (2) moistening the crushed clay with a fine mist of water while tumbling on a rotating disk, (3) drying the misted clay, and (4) calcining the dried clay at 750° C in a fluidized bed. Clay treated by this method was leached with HCI, and its residue was washed by water displacement in 4-ft-deep beds. Bed permeabilities on the order of 47 darcys or 4.6 x 10-7 cm2 were obtained with the leached residues.

Jan 1, 1983

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By B. W. Dunning

The Bureau of Mines investigated the concentration and distribution of precious metals in the various fractions produced from mechanical processing of obsolete military electronic scrap. Whole avionic units, printed circuit cards, and electrical connectors were processed and analyzed. Materials recovered included baghouse lights, wire bundles, mag-netics, and metal concentrates from eddy-current and high-tension sepa-ration. Higher value fractions were processed by a commercial toll refiner for recovery of gold and silver. Lower value fractions were analyzed by the Bureau. Three fractions, the lights, wire bundles, and metallics from high-tension separation, contained most of the precious metals. Depending on the type of scrap feed, these fractions represented 34 to 60 pct of the original sample weight. Collectively, they represented 68 to 97 pct and 75 to 98 pct of the contained gold and silver, respectively.

Jan 1, 1983

By R. K. Conrad

The Bureau of Mines conducted corrosion research to determine suitable construction materials for geothermal resource recovery plants. Weight loss, pitting and crevice corrosion, U-bend stress corrosion, and electrochemical polarization measurements were made on selected metals in brine and steam process environments produced from high-enthalpy hypersaline brine from geothermal well Magmamax No. 1 at the Salton Sea Known Geothermal Resources Area, Imperial Valley, Calif. Cadmium (and by extension cadmium coatings) and a 6061-T6 aluminum alloy were unsatisfactory because of high general corrosion rates and, in the case of aluminum, severe pitting Molybdenum and niobium (columbium) were resistant to general corrosion, pitting, and crevice corrosion, Copper alloys corroded at rates that may preclude their use in wellhead brine, The presence of iron accelerated the corrosion of the copper alloys Titanium alloys were resistant to general corrosion and stress corrosion cracking in all of the environments. They exhibited crevice corrosion in some of the brine and steam environments and Ti6A14V pitted in the brine environments. They exhibited passive behavior over a broad range of potentials. Exposure tests were conducted on a high-temperature polyphenylene sulfide thermoplastic (Ryton) in the same environments. A 40-pct-graphite fiber-reinforced Ryton composite deteriorated readily in wellhead brine and failed in all of the brine and steam process environments; Ryton coatings on 316L stainless steel were adherent and performed well.

Jan 1, 1983

By Laurel A. Powers

The Bureau of Mines process for recovering Ni and Co from low-grade domestic laterites uses a reduction roast followed by an ammonia, ammo-nium sulfate leach. This investigation examined the waste streams of the process for their potential environmental impact and focused on the laterite residue produced. The U.S. Environmental Protection Agency's extraction procedure (EP) toxicity tests and column leaching showed that leachable metal concentrations would be low enough so that the residue would not be considered a hazardous waste under present definitions. Under nonacid leaching conditions, about the same amount of metal was extracted from laterites as from their residues, and the leachates were similar to water samples from an undisturbed laterite deposit. Washing tests on the laterite residue showed that ammonia and ammonium sulfate concentrations were reduced according to equilibrium stage calculations, resulting in residues that would be acceptable for revegetation. With water washing only, the residue would not be considered a hazardous waste even though significant amounts of Ni and Co were absorbed from entrained leach solution onto the residue. Washing first with fresh leach solution and then with water prevented this absorption and thus improved the overall metal recovery.

Jan 1, 1983

By R. F. Chaiken

The Bureau of Mines has conducted a study of mine fires in the Anthracite Region of Pennsylvania to determine the most effective approaches to fire control in this area. The problems involved in controlling an anthracite fire include the geological and mining conditions in this area, the propagation characteristics of anthracite, the fire control methods available, the hazards associated with these fires, and the mar-ginal effectiveness of past fire control projects. From this genecal background, fire control options were discussed as they apply in ISBO to the Centralia mine fire. Probable effectiveness, feasibility, and costs were assessedv The options evaluated include four excavation plans, flooding, hydraulic flushing, water curtain isolation, mining to construct an underground carrier, burnout control, and relocation of the community. The most advantageous from a technical viewpoint is an excavation method combining complete excavation of the fire zone within the borough with trenching to confine the remaining fire. It appears that for many anthracite fires, as for the Centralia mine fire, there are no available control measures that have a moderate cost, are proven effective, and produce minimal disruption on the surface.

Jan 1, 1983

By T. W. Smelser

This Bureau of Mines report presents a review of underground testing, test results, and design guidelines of steel-fiber-reinforced concrete (SFC) mine support (cribbing) developed at the Spokane Research Center. The objective of the work was to verify, in field applications, the performance, economics, and acceptance by the mining industry of the SFC supports and establish design guidelines for their use underground. Results indicate superior performance, favorable economics, and enthusiastic acceptance by the mining industry.

Jan 1, 1983

By J. A. Eisele

The Bureau of Mines is investigating the recovery of alumina from domestic nonbauxitic resources, including anorthosite. The United States has large reserves of anorthosite, but its aluminum content is less than 50 pct soluble in acid, unless a source of fluoride is added to the acid. A flowsheet that includes leaching with HCl and fluoride followed by crystallization of AlC13.6H20 from the pregnant liquor by HCl gas injection was designed. Approximately 90 pct of the aluminum values were recovered from the anorthosite when a ratio of 0.14 mole of fluorine per mole of aluminum was used. Sodium chloride is cocrystallized with the A1C13.6H20 but is removed by water washing of the Al203 product. A material balance is given based on results of laboratory studies of the unit operations.

Jan 1, 1983

By Seth C. Schaefer

The Bureau of mines investigated thermodynamic properties of MnSO4 and 2CdO CdSO4 to obtain basic thermodynamic data applicable to the treatment of mineral concentrates during roasting and sintering processes. Standard Gibbs energies of formation were determined with high-temperature galvanic cells using stabilized Zr02 as the electrolyte. Potential measurements were obtained from the cells?

Jan 1, 1983

By W. C. McLaughlin

Under a cooperative agreement, the Bureau of Mines, Magma Copper Co., and ASARCO, Inc., tested backfilled ground support systems at t.wo elevations in Magma's San Manuel, AZ, mine. The tests were mainly for guidance in designing the loading crosscuts of the new ASARCO Sacaton underground mine. Two-piece, wide-flange steel sets for 8-by 8-ft (2.44-by 2.44-m) and 11-by II-ft (3.36-by 3.36-m) openings were designed. Set spacing was 3 ft (0.91 m) and 5 ft (1.52 m), respectively. After erection, the sets were lagged with various test materials. The void between the lining and the ground was backfilled with sand and pea gravel. Instruments measuring strain (used to determine changes in stress) were placed beneath the sets and in the backfill. Results indicate the backfilled sets in the smaller drift (2315 grizzly level, panels 6 and 7) of 8-by 8-ft (2.44-by 2.44-m) cross section are a viable permanent support system, lower in cost than the standard formed concrete. Results are inconclusive in 2615 grizzly level, panels 5 and 6, where wide-flange steel sets were used with 5-ft (1.52-m) long concrete gob lagging of T-design.

Jan 1, 1983

By S. J. Gerdemann

In support of its objective to improve mine safety, the Bureau of Mines has searched for better materials and systems to anchor roof bolts. TIlis report describes a study on the effects of mine waters upon accelerated gypsum, one of the materials under consideration. The accelerated gypsuw dissolved at an appreciable rate relative to an assumed 10-yr life span of a roof bolt. Surface orientation, initial ion concentration of a dissolving solution, and flow rate of the solu-tion had substantial effects on the dissolution rate. Factors such as water-cement ratio, accelerator content, wax capsule additions to the gypsum in cartridge-installed bolts, surface area, temperature, and curing duration had little effect. In an actual roof-bolt environment, dissolution will occur in static solutions to the solubility limit of gypsum (~2 giL) and cease, result-ing in minimal damage; but in flows of unsaturated solution as slow as 1 L per month, a loss of up to 10 pct will occur in 2 yr. Since miners cannot readily measure the flow or ion concentration of static-appearing water at every roof-bolt site, all such water must be assumed to be pure and flowing. It is recommended that gypsum-bonded roof bolts be confined to dry roofs only.

Jan 1, 1983

By H. William Zeller

The Bureau of Mines is conducting research to determine whether the use of chemical surfactants improves respirable coal dust control and is evaluating laboratory test criteria for selecting effective surfactants. This publication presents the results from wetting effectiveness tests with emphasis on the capillary rise test. The test variables investigated included coal particle size, type of surfactant, surfactant concentration, test duration, and mineral con-tent of the water. In addition to the rise test, measurements of con-tact angle, zeta potential, and sink time for various coal and surfactant combinations were conducted. No significant correlations among the four wetting tests were observed, a surprising result which implies that each test type measures specific aspects of the wetting phenomenon and also that each test type should only be used to select surfactants for specific applications. For example, the rise test shows solution penetration into porous materials, and the sink test discriminates among surfactants for dispersing finely ground materials into suspension. Another important conclusion is that combinations of agents retain their individual wetting properties, allowing mixtures to be for-mulated to perform well in both rise and sink tests.

Jan 1, 1983

By R. R. Lowery

An analysis of three 1-1/4-diam manufactured wire ropes of 6x19 classification was done to identify and describe reference conditions of new rope. Reference condition is of value when examining tested or retired ropes. Measurements of strand and rope pitch and of wire and rope diameter confirmed adherence of all ropes to those construction specifications. Mechanical properties of strength and ductility were determined by accepted methods for the ropes and wires from the ropes. Individual wires from one rope failed to meet minimum wire ductility values. Wire chemical composition varied in average carbon levels, from 0.70 to 0.78 wt pct, and in manganese content, from 0.45 to 0.80 wt pct. One manufacturer's product contained 1 to 3 wt pct Ni and Cr. Heavily wrought pearlitic steel microstructures were porous and contained inclusions. Cold work variations were evidenced by wrought grain width. Recorded anomalies reflected the condition of the manu-factured products. The report provides data that compare the three wire ropes studied, but cannot verify the effects that these conditions or anomalies have on rope service life.

Jan 1, 1983

By August J. Kwitowski

This report presents the results of a joint Bureau of Mines-U.S. Department of Energy project that evaluated a newly developed low-coal mining system: the 4M miniminer system. The evaluation took place from April through October 1981 and determined potential health, safety, and productivity factors for the mining system using the surface test facilities at Bruceton, PA. The planning, testing, results of testing, and a summary evaluation of the 4M miniminer system are included in the report. The miniminer system was found to be a very good concept with future potential for safe, healthful, and economic production in thin-seam mining. The mining system was also judged to have considerable potential for use in some coal seams that are presently considered unminable by other existing mining equipment. The preproduction, prototype version of the miniminer system that was tested suffered from several safety and production problems. These problems are also described, along with suggested remedies.

Jan 1, 1989