Search Documents

By H. Deveci

Bioleaching/biooxidation is essentially a dissolution process with the involvement of acidophilic bacteria acting as the "catalyst" to accelerate the dissolution of metals from sulfide minerals. The contribution of bacteria to the metal dissolution is closely controlled by the growth of bacteria, which is itself affected by the physico-chemical conditions within the bioleaching environment. There are a number of operating parameters controlling bioleaching processes, which are required to be maintained within a certain range in the leaching environment whereby the activity of bacteria with the resultant oxidation of sulfide minerals can be optimized. In this regard temperature, acidity, oxidizing conditions, availability of nutrients, oxygen and carbon dioxide, surface area and presence of toxic ions are of prime importance for control and optimization of bioleaching of sulfide ores/concentrates. Bioleaching processes are temperature and pH dependent with optimum metal dissolution occurring in a particular range where the bacterial strain is most active e.g. mesophiles at 35-40°C and pH 1.6-2.0. Provision of nutrient salts is required to maintain the optimnm growth and hence metal dissolution with the quantity of nutrients apparently being dependent on the availability of substrate i.e. head grade/pulp density of an ore/concentrate. Oxygen transfer is one of the most critical factors since the oxygen levels below 1-2 mgll may adversely affect the oxidizing activity of bacteria. Bioleaching rate tends to improve with increasing the surface area at low pulp densities but, in practice. the pulp density is limited to -20010 w/v. Increasing concentrations of ions such as cr may also adversely affect the oxidative activity of bacteria. Keywords: Bioleaching, Biooxidation, Acidophilic bacteria

Jan 1, 2003

By Richard W. Lawrence

Leaching of copper from sulfide minerals using biooxidation offers a potential route for copper recovery. Oxidation of . sulfide sulfur can proceed either; to sulfate or to elemental sulfur depending on mineralogy and process conditions. The advances in commercial application of biooxidation for sulfidic gold ores has made available operating and cost data which allow the derivation of conceptual costs for copper ore processing for comparison with conventional processing routes. Although costs for copper biooxidation generally remain high relative to conventional smelting, application might be competitive in specific cases. Biooxidation becomes more competitive in the general case if the cost ofS02 emissions in pyrometallurgical processing were to be internalized to a greater degree than currently required. This paper describes the technical aspects of biological processing of copper sulfide ores and concentrates, specifically with respect to the fate of sulfur. The environmental and economic implications of the biooxidation route are discussed in relation to conventional processing.

Jan 1, 1996

By F. Leuzzi

Asbestos is a natural mineral fibre which has been known and utilized commercially for about a century. From the forties, it was employed on an ever-increasing scale throughout the mechanical engineering, building, paper-making and plastics sectors, to name but a few. There are essentially five minerals which provide fibres for industrial applications, namely, the chrysotile variety of serpentine and the amphiboles such as riebeckite, anthophyllite, cummingtonite-grunerite (amosite) and tremolite. About a fifth of the world's asbestos output was once taken by Europe for the manufacture of asbestos-cement products, reinforced plastics, paper and cardboard, panels, soft insulation and spray-on powders. However, in the sixties and seventies the hypothesis regarding the pathogenic nature of asbestos fibres started to gain ground. Moreover, between the sixties and eighties the EU issued a series of regulations designed to bring about a steady decrease in asbestos consumption. This line of action has culminated in recent years in a whole set of directives banning the use of asbestos in all products. This created a major problem, namely, how to clean-up the several million tons of various types of asbestos products in various states of conservation existing in Western Europe. CORDIAM (Pat. RM95 A 000269 and Pat. RM96 A 000782 in the name of ECOTEC S.r.1.) is one of the thermal inertization techniques recently proposed for this purpose. The process provides for the low-temperature ceramization of the toxic-harmful material. Of course, with such a great variety of waste materials and the volumes to be treated, as well as the need to ensure the correct dimensional design of the thermal sections of the treatment plant, it is necessary to know as much as possible about the thermal behaviour of the wastes concerned. This paper details the steps taken firstly to ascertain the thermal behaviour of such materials as may be encountered in day-to-day practice and secondly to examine the influence of the main process parameters on the preliminary design of gas- or fuel-oil-fired rotary kilns of the kind used for waste treatment.

Jan 1, 1999

By Xun An

Slag from an electric slag cleaning furnace was injected with methane and air mixtures to facilitate the recovery of copper and cobalt. The effects of methane-to-air ratio, gas flow rate and temperature on the reduction and metal separation were investigated. The results showed that over 90 percent copper and up to 60 percent cobalt could be recovered from the slag with a gas utilisation of around 70 percent, as calculated by thermodynamic simulation. Methane-to- air ratio was a major factor affecting the rate of reduction under the present experimental conditions. Further, injection of gaseous reductants greatly enhanced the coalescence and settling of entrained metal droplets. A reduction mechanism is proposed and the factors influencing the coalescence of copper droplets are discussed.

Jan 1, 1998

By A. C. Mollison

In November of 1983 a fire inside the autoclave caused the curtailment of operation of the Kidd Creek pressure leaching facility. Subsequent repairs and recommissioning of the autoclave in 1984 allowed Kidd Creek to increase its production of zinc as originally planned. This paper describes the operation of this process from 1984 to 1988 and details major mechanical work carried out on the vessel in 1.988:

Jan 1, 1990

By R. Cavanagh

Studies relating to the fixation of sulfur by reaction of 4 to 8 mm diameter cylinders of calcined limestone or dolomite with high strength sulfur dioxide in the temperature range 880°C to 1020°C were undertaken. Dolomites are far superior in sulfate capacity and reactivity than dense limestones even at high strength SO2. The sulfation reaction was first order with respect to SO2 concentration below 100 percent. Zero reaction rate at 100 percent SO2 concentration indicates that sulfate was the exclusive reaction product and that sulfite had no role in the reaction. At relatively low SO2 concentrations gaseous diffusion through the reaction product layer has a marked effect on the rate. As SO2 concentrations were increased up to 100 percent more complex rate controlling mechanisms unfold. By sectioning partially reacted dolomitic limestone pellets a moving interface was observed. Reaction ceased because of pore plugging for dense non-porous limestones at 30% conversion. With dolomitic material virtually complete sulfation of the calcium was observed. S.E.M. analysis showed that the average atom ratio Ca:S was 1.01, thus supporting the argument that little if any of the magnesium was sulfated.

Jan 1, 1996

By J. Fogarty, J. Sofra

The mobile telecommunications sector is one of the fastest growing industries worldwide. However, increasingly stringent environmental regulations are placing pressure on manufacturers to accept responsibility for end of life products. The companies are therefore exploring avenues to recover the valuable components contained within the mobile telecommunications devices thus reducing the quantities of toxic components going to landfill. Batteries used to power the devices, are typically based on either nickel-cadmium, nickel metal hydride, or lithium ion cells. They contain toxic metals including nickel, cadmium, lithium, potassium, lead, and cobalt in a complicated arrangement of battery cells surrounded by a metals then plastic casing. The Ausmelt Catalytic Waste Converter (CWC) for waste treatment and recycling is well suited to processing all three mobile phone battery types for the recovery of valuable metals in marketable products that can be recycled to industry without turning out harmful levels of toxic emissions. Ausmelt recently demonstrated the capabilities of its CWC by continuously processing 4.5 tonnes of nickel-cadmium batteries. Using Ausmelt's pilot plant facility in Australia, the nickel-cadmium batteries were processed to produce a nickel iron sulphide (matte), a cadmium fume and a final slag which satisfied CS toxicity leach test criteria and was safe f<~r disposal to landfill. This paper explores the commercial development of the Ausmelt CWC for treating each of the three battery types in light of (a) the outcomes of the recent demonstration, and (b) the current and expected future availability of batteries for processing.

Jan 1, 2000

By Sarah Beutner Mavrogenes

The mineralogy of three slags from a domestic secondary copper refinery were studied by applied mineralogical techniques to determine the: 1) phases present, 2) phase chemistry, 3) phase abundance, 4) associations, 5) crystalline habit, 6) grain size, 7)microtextures, and 8) causes for certain metallurgical problems, such as metal losses to the slags. The slags were produced by skimming the bath prior to melt-down to allow heat from the flame to reach the bath. The first slag is highly viscous and all three slags contain a large amount of copper. The "first slag", which is skimmed prior to treatment of the bath with fluxes, contains metallic copper, cuprite, delafossite, magnetite, Mg-hercynite, common spinel-chromite solid solution, picrochromite-chromite solid solution, common spinel-picrochromite solid soiution, gahnite, cassiterite, silica-rich glass, and corundum. Its abundant solid refractory phases make the slag difficult to skim. The "soda-rich slag", skimmed after the treatment of the bath with sodium carbonate flux, contains cuprite, delafossite, magnetite, cassiterite, Na-Al-silicate, and Na-Al-Ca-silicate. It contains less metallic copper than the first slag and lacks the refractory minerals. The "phosphorus-rich slag", skimmed after treatment of the bath with a copper phosphide flUX, contains metallic copper, cuprite, delafossite, berlinite, cassiterite, silica, apatite, Cu-Fe-rich apatite, copper phosphate, Cu-Fe-phosphate, and a Pb-phosphate. In contrast to the above three copper-rich slags, recent charges have produced a silver-copper-rich slag. The "silver-rich slag", skimmed after the treatment of the bath with a copper phosphor ide-borax flux, contains, cassiterite, delafossite, cuprite, a Na-Al-silicate, magnetite, metallic copper, MgO, common spinel-chromite solid solution, and wollastonite. Silver ranging from 0.05 to 2.02% was found by atomic absorption and inductively coupled plasma spectrometry analyses in the metallic copper phase.

Jan 1, 1989

By René Winand

The paper gives a synthesis of research work performed in the department during the last ten years and dealing with cobalt , copper and manganese electrodeposition in chloride aqueous solutions. Special emphasis is given to electrocrystallization. For copper, properties of the electrolyte such as solubility limits, electrical conductivity and complex ions stability are discussed in connection with leaching, purification of the electrolyte, and metal recovery. When possible, kinetic parameters and probable electrode mechanisms are given. Problems that are still to be solved are also listed.

Jan 1, 1985

By L. Xia

Sodium silicate(s), also known as “water glass”, are one of the oldest and most widely used industrial chemicals. Its first use in Canadian operations can be traced back to around 1925, which coincided with early use of xanthates in mineral flotation. Silicate functions as a sulphide and non-sulphide gangue mineral dispersant, depressant and modifying reagent in grinding and flotation operations. It is believed that soluble sodium silicate promotes selectivity of value added sulphides against gangue minerals, resulting in both grade and recovery improvement. This paper seeks to link improved grade/recovery to the interaction characteristics of minerals and the sodium silicate. A systematic study was performed with individual mineral species, an artificially designed model ore and the feed ore from a copper flotation operation. The function of sodium silicate was evaluated in the context of colloidal chemistry and linked to mineral surface chemistry. Measurement of pulp rheology and mineral zeta potential identified that sodium silicate works as a dispersant. The dispersion is accomplished by increasing a mineral’s net surface charge, resulting in a change in slurry viscosity. Bench scale laboratory flotation tests suggest that better dispersion leads to a diminished interaction of chalcopyrite with gangue. The improved Cu grade and recovery then are likely in response to an increased accessibility to collector along with a linked increase in particle bubble attachment resulting in better separation efficiency. ToF-SIMS surface chemical analysis of the flotation samples found a higher proportion of sodium silicate on minerals from the flotation tailings relative to the concentrates. Moreover, attachment of sodium silicate appears to be mineral specific; the data indicates that sodium silicate favours the surface of gangue phases over the value sulphides.

By T. Shi, Q. Yuan, S. P. Vanka, B. G. Thomas

"The quality of continuous cast steel is greatly affected by fluid flow in the mold region, especially involving transient phenomena. Mathematical models are being applied to investigate many different aspects of these phenomena, but their accuracy must be validated before they can be applied with confidence. As part of a long-term effort to develop and apply comprehensive models of the continuous casting process, this work evaluates the relative accuracy of models of three different fluid flow phenomena in continuous casting through comparison with measurements.Firstly, transient flow simulations of velocities in the mold region are compared with digital particle image velocimetry (PIV) measurements in a single phase water model. Large-eddy simulations (LES) are found to reasonably match the flow measurements, including transient flow variations, except at long time scales, which could not be modeled owing to the excessive computation costs. The standard K-e model produced very good agreement with time-averaged velocities for relatively little computation time, although it is inaccurate at predicting the transient variations. Secondly, particle trajectory calculations are compared with water model measurements to study the distribution and flotation removal of inclusion particles. The LES model was able to match the measurements both qualitatively and quantitatively. Thirdly, steady, multi phase flow computations are compared with flow patterns observed in both a water model and an operating steel caster with argon gas injection. For the same conditions, the water model and steel caster produced very different flow behavior. The computational model was able to match the measured flow patterns in both cases.This work suggests that computational flow modeling has the potential to match real processes as well or better than water models, especially when complex related phenomena such as particle motion and multiphase flow are involved. Much work is still needed to further improve the models and to apply them in parametric studies."

Jan 1, 2001

By Ernt. W. D.

A membrane based mixed extractant process was developed for selective removal of copper from waste acidic cupric chloride etchant solutions found in printed wire board manufacturing. The process uses a mixture of Adogen 381 (tri-isooctylamine), MOC®-45 (ketoxime) and MOC® 55TD (aldoxime) in a kerosene diluent. The mixed extractants recover the copper from a hydrochloric acid medium and transfers it to a sulfuric acid medium. The process also utilizes unique wetted membranes to separate the aqueous and organic phases. The driving force for these membranes is not pressure but the difference in surface tension between the two phases. By using these membranes, complete phase separation results. There is no physical entrainment contamination as found in conventional systems. The only cross contamination is the solubility concentration of one phase in the other. This however is less than 10 mg/l.

Jan 1, 1998

By J. A. Bustnes

The present work deals with kinetic studies of the reduction of molybdenum- and tungsten oxides by hydrogen. The experimental method used was therrnogravimetry under isothermal as well as non-isothermal conditions. The non-isothermal kinetics in the case of the reduction of MOO, to Moo2 has been modeled considering surface reaction as rate- controlling. In the case of the reduction of W02 to W a model was developed on the basis of the movement of the reaction front. The activation energies calculated on the basis of the models were in good agreement with those derived from isothermal experiments.

Jan 1, 1994

By N. Kanari

One of the criteria to define the market value of chromite concentrate is its chromium to iron ratio. Changing this ratio for a definite chromite mineral is impossible by physical processing. This study investigated the possibility of increasing this ratio through the carbochlorination and the oxychlorination of chromite concentrates. Experiments are carried out up to 1000 °C. The characteristics of samples and reaction products are determined by SEM, XRD and chemical analysis. The carbochlorination of a chromite concentrate at about 600 °C leads to the . selective partial elimination of iron allowing a higher Cr/Fe ratio of the treated concentrate. Selective extraction of iron could also be achieved at about 950 °C by oxychlorination. In this case, a part of chromium contained in the concentrate is recovered as chromium oxychloride. The obtained residue had high content of Cr, Mg and A1 oxides. Such material has probably better chemical and thermal properties that may. be useful for foundary and refractory applications. Two flow-sheets for the beneficiation of the chromite concentrates using carho- and oxychlorination are suggested.

Jan 1, 1997

By J. Gartelmann, B. Zaslavsky, Y. Vojta, D. J. Chaiko, W. Mego, A. N. Rollins

"Aqueous biphasic extraction (ABE) processes offer the potential for low-cost, highly selective separations. This countercurrent extraction technique involves selective partitioning of either dissolved solutes or ultrafine particulates between two immiscible aqueous phases. The extraction systems that we have studied are generated by combining an aqueous salt solution with an aqueous polymer solution.We have examined a wide range of applications for ABE, including the treatment of solid and liquid nuclear wastes, decontamination of soils, and processing of mineral ores. We have also conducted fundamental studies of solution microstructure using small angle neutron scattering (SANS). In this chapter we review the physicochemical fundamentals of aqueous biphase formation and discuss the development and scaleup of ABE processes for environmental remediation.IntroductionAqueous biphasic extraction (ABE) is a highly adaptable separation technique that can be used in a wide range of applications. We have been evaluating various types of ABE systems for possible applications in the treatment of solid radioactive wastes (1,2), liquid nuclear wastes (3,4), and contaminated soils (5-7), and in the removal of organics from aqueous salt solutions (8). We have also conducted fundamental studies of the solution microstructure of ABE systems using small angle neutron scattering (SANS) (9).The extraction systems are generated by combining an aqueous salt solution and an aqueous polymer solution. This produces two distinct liquid layers that are as immiscible as oil and water, yet each liquid layer contains at least 70 to 80 wt % water. The biphasic systems that we have been working with consist of immiscible polyethylene glycol (PEG) and salt solutions. Some inorganic salts that promote biphase formation with PEG solutions include the sodium/potassium salts of sulfate, carbonate, phosphate, and hydroxide (10)."

Jan 1, 1996

By C. D. Chapman

Current regulations regarding the landfill disposal of asbestos containing wastes are inadequate to ensure there are no ground water or airborne emissions. Accordingly, there is growing recognition that asbestos wastes can only be safely disposed of by using techniques that destroy the hazardous fibres. An innovative high-temperature plasma arc technology (The MAGRAM Process) is being developed for the recovery of magnesium metal from asbestos together with supplementary magnesia containing feedstock. The furnace will operate in. open bath mode with aluminium and/or ferrosilicon being employed as reductant. An important advantage of the process is that magnesium vapour within the furnace will be generated close to atmospheric pressure rather than at reduced pressure under which existing processes operate. Thermodynamic modelling work has been undertaken to define the range of slag composition and furnace temperature under which magnesium production at atmospheric pressure is feasible. The effect of slag chemistry, reductant addition, and temperature on product quality and yield have also been investigated and key aspects have been tested on bench scale. A 300 kW pilot plasma furnace unit has been employed for the treatment of calcined asbestos wastes. Aspects of design and operation of the unit are detailed. Acknowledgement: This work is substantially financially supported by the European Communities under the Industrial and Materials Technologies (Brite EuRam H) Research and Development programme.

Jan 1, 1995

By Yimin Ruan

"An inverse design method is developed to obtain the optimal cooling conditions for the continuous quenching of precipitation hardenable sheet alloys to achieve the required yield strength. The yield strength of a precipitation hardenable alloy is obtained by allowing solute to enter into solid solution at a proper temperature and rapidly cooling the alloy to retain the solute in the solid solution. An aging process may be needed for the alloy to develop the final mechanical properties.The objective of the design is to optimize the quenching process so that the required yield strength can be achieved. With the inverse design method, the required yield strength is specified and the sheet thermal profile at the exit of the quenching chamber can also be specified. The conjugate gradient method is used to optimize the cooling boundary condition during quenching. The adjoint system is developed to compute the gradient of the objective functional. An aluminum sheet quenching problem is presented to demonstrate feasibility of the inverse design method.IntroductionQuenching is a critical step in metal production to achieve desired material properties, such as yield strength, hardness, etc., for precipitation hardenable alloys. In most cases, rapid quenching from the solution heat treatment temperature is necessary to obtain the required material properties, but rapid quenching may cause other problems such as excessive distortions of the quenched materials.In a solution heat treatment, the alloy is heated to a suitable temperature, held at that temperature to allow the soluble alloying elements to enter into the solid solution, and cooled rapidly (quenching) to retain the alloy elements in the solid solution. An aging process, which controls precipitation of fine particles at room (natural aging) or elevated temperatures (artificial aging), is generally followed after the quenching process to develop the final mechanical properties of the heat treated alloys."

Jan 1, 1998

The high pressure acid leach process (HPAL) is being commercially used in four plants around the world to treat limonitic laterites. The two major operating costs of the HPAL process are the sulphuric acid and the energy required to heat the pulp to the desired temperature (>240°C). As an alternative to acid injection and steam heating, the in-situ generation of sulphuric acid and heat, produced during the high temperature pressure oxidation of sulphur-bearing materials blended with laterites, has been investigated at the laboratory scale. Various sources of sulphur have been examined, in particular, elemental sulphur, pyrrhotite and a Cu-Ni low-grade bulk concentrate. Under the proper blend ratios, all sulphur sources tested generated sufficient acid to result in equivalent nickel and cobalt dissolutions. A significant improvement to the process economics can result from the addition of sulphur sources containing valuable by-products, such as nickellcobalt andlor precious metals (gold and PGMs). This is especially true in the latter case, when the HPAL can be operated under Platsol conditions (i.e. with the addition of 5-10g/L of chloride), to dissolve the base metals and precious metals simultaneously in the autoclave. Various examples of the application of this concept are presented, together with a brief discussion of its implication on the autoclave design and the downstream processes to recover the values from the leach solutions. Keywords: limonite, co-treatment, acid consumption, sulphur, sulphur compounds, pressure acid leach (HPAL, PAL), Platsol process

Jan 1, 2004

By M. Fujikawa, S. Goto, M. Nishikawa

"The semi-pilot scale plant for injection smelting of zinc calcine was operated under the committee of Joint Research Organization of Injection Metallurgy. The capacity of the plant is 10 ton metallic zinc per day. The plant was designed by the resul ts of basic and bench scale tests of the capacity of 1 ton metallic zinc per day which was published at ""Zinc '85"". The equipments of the plants, operational conditions, results of the operation such as recovery of zinc in injection furnace and condenser, combustion rate of powdered coke and consumption of energy in this process are presented in this paper. The results of the study of the feasibility of the commercial plant of 100,000 ton zinc per year by the injection smelting are also discussed in the paper. IntroductionThe research committee of new smelting process of zinc by injection was established in 1981 under the finantial support of Mining Promoting Foundation of Japan. Six zinc producing companies joined in this organization. The price of zinc was very low at that time and the energy cost, especially, cost of electric power in Japan was extremely high. Invention of a new economical process for zinc extraction had been stronglydesired. The author proposed a injection smelting of zinc as a economical process in energy saving after a calculation of thermodynamical equilibrium and heat balance(1 )(2).The research committee has been studying the injection process since 1981. The small basic experiment by using a crucible furnace was carried out from October 1981 to March 1983 and the reaction of reduction of calcine by injection smelting was ascertained (2). Vaporizatipon of zinc and behaviours of impurities were examined. After the basic experiment, the bench scale test with the production capacity of zinc of 1 ton per day was carried on from November 1983 to October 1984.The bench scale tests were carried out to obtain the proper design of feeding devices of calcines and coke into a furnace and also to obtain fundamental data for enlargement of this smelting process(3,4). The recovery of metallic zinc in this small equipments was about 50% and main loss of zinc was formation of dross in the condenser."

Jan 1, 1988

By William Petruk

"Heap leaching is a developing technology for recovering native gold and electrum from low grade deposits and from tailings. Recovery depends on permeability of the rock and ore minerals, size of particles in the heap, and ore textures that influence exposure of gold grains to cyanide solutions. These ore textures include gold-bearing veinlets and microveinlets along fractures and microfractures, gold grains in porous minerals and rocks, and gold graim. occurring along grain boundaries of other minerals. On the other hand, small encapsulated gold grains arc not likely tote exposed even with fine grinding. Most gold grains that occtir along grain boundaries of other minerals can be exposed with a moderate to fine grind, but the. resulting material will be too fine-grained to be permeable in a heap. Such finely ground ore, as well as tailings from flotation operations, can however be prepared for heap leaching by agglomerating the material into porous briquettes. Oxidized and weathered zones above. orebodies are frequently amenable to heap leaching because the gold-bearing pyrite and arsenopyrite have become permeable by conversion to porous iron oxides and ferric oxyhydroxides. A review of ore textures in several types of gold deposits suggests that:(1) the gold in vein deposits would gtmerally be amenable to heap leaching of both oxidized ores and fresh non-refractory ores,(2) the gold in Carlin-type deposits and in volcanogenic massive sulfide deposits is not likely to be amenable to heap leaching fresh ore, but oxidized zones above the orebodies are generally amenable to cyanidation, and(3) the gold in porphyry copper-gold deposits and in Witwatersrand-type deposits would likely be amenable to heap leaching of both fresh and oxidized ores but with high cyanide consumption."

Jan 1, 1997