Search Documents

By Edward S. Plotkin, Gary A. Almeraris, Thomas F. Peyton

The lining of the tunnel and shafts for a new section of New York City's- water system required extensive components to produce, deliver and place a continuous tunnel linning. The project placed approximately 153,000 CM (200,000 cy) of concrete for 5,340 M (17,520) of drill and blast 7.3 M (24 ft.) ID tunnel, located at depths of 152 M (500 ft.) to 213 M (700 ft.) . This section of tunnel will be connected to the surface water distribution system via four shafts of varying diameters ranging from 5.8 M (19 ft.) ID to 1.5 M (5 ft.) ID . All work was done beneath the streets of Manhattan under the rigid constraints of the City of New York and the Bureau of Water Supply regulations.

Jan 1, 1987

By A. L. de Vegt

Hydrogen sulfide is an expensive chemical used in nickel, zinc and copper mining and metallurgical operations for selective recovery and concentration of metals from leach water streams, acid plant blow down streams, refinery electrolyte bleeds and precious metal plant bleeds. Hydrogen sulfide is either produced on site by catalytic reduction of elemental sulfur or transported to the site as liquefied hydrogen sulfide (H2S) or as a sodium sulfide solution (NaHS). Biologically produced hydrogen sulfide has economically very interesting application possibilities in the mining and metallurgical industry. Converting sulfates from waste streams into usable hydrogen sulfide by biological reduction results in operational cost savings in existing lime treatment systems. H2S can be produced biologically for less than $500/ton S. For the past ten years Paques has been engaged in the development and installation of treatment systems based on biotechnological processes to remove sulfur compounds from water, air and gaseous streams. Paques has designed and installed a groundwater treatment system for the Budelco zinc refinery in the Netherlands to remove sulfate and heavy metals. The hydrogen sulfide produced is used for recovery of metals, mainly zinc, from the ground water stream. The system has been operating since May 1992 treating a flow of 5000 m3/d. At Kennecott's Bingham Canyon Utah copper mine a pilot plant started operation in November 1995 to develop the process for selective recovery of copper from leach water using biologically produced hydrogen sulfide from sulfate containing groundwater. Other pilot plants are operated at DOE's Pittsburgh Research Center and at Cominco Research focusing on selective recovery of metals.

Jan 1, 1998

By Shawn McWilliams, Aini Sun, Mike Lichte, Greg Colzani

The Allegheny County Sanitary Authority (ALCOSAN) adopted its Clean Water Plan (CWP) in May 2020, as part of a federal consent decree to comply with the USEPA’s Combined Sewer Overflow (CSO) Control Policy. Planned improvements include constructing a new regional storage/conveyance tunnel system, promoting green infrastructure/ source control, and expanding the treatment plant. Preliminary planning for the tunnel system was completed in October 2020. The Ohio River Tunnel (ORT) project is the first of three tunnel projects that make up the regional tunnel system. The ORT project began final design in 2021. This paper discusses the advancements made to the ORT preliminary planning concepts considering property availability, alignment optimization, tunnel boring machine evaluation, contract packaging and delivery schedules.

Jun 13, 2023

By W. R. Hail

A proactive design and construct approach was used to remediate the Warm Springs Ponds Complex near Anaconda, Montana under "Superfund". The pond complex is used for treatment/settlement of heavy metals and is a repository for 19,000,000 cubic yards of tailings, precipitates and associated sediments. Remediation has resulted in treatment/settling capacity for flows up to the 100-year flood (3,300 cfs); expansion from 5 to 11 ponds in series requiring 12.5 miles of new or improved embankments with associated hydraulic structures; flood protection for the 0.5 Probable Maximum -Flood (PMF) (70,000 cfs); and closure of exposed tailings along with aquatic and terrestrial habitat enhancement.

Jan 1, 1995

By G. J. Schneider

The higher stress zone adjacent to an underground opening causes a velocity anomaly that can be mapped in favorable conditions with an acoustic cross-borehole logging system. Bureau personnel used a specialized system at the Colorado School of Mines test site near Idaho Springs, Colorado, to locate the Edgar Mine tunnel and its associated stress anomaly. Data from the logging system' were processed with a tomographic image reconstruction algorithm to map the opening and the location of the high velocity zone around the opening. The velocity imagery from tomographic analysis compared favorably with predictions from numerical modelling of the location of the stress anomaly.

Jan 1, 1988

By C. Alexander

Stillwater Mining Company is developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in south central Montana. A 5650 meter (18,550-foot) tunnel is required to gain access to the ore bearing horizon (J-M Reef). Access and primary mine development can be accelerated through the use of two 4.6 meter (15-foot) diameter tunnel boring machines (TBM). One TBM was purchased new while the other was purchased used. Machine specifications, site support facilities, portal/launch chamber construction, TBM assembly, startup and operation are discussed in this paper.

Jan 1, 1999

By D. McElhinney, J. Winfield, G. Buchan, B. Slaker, A. Iannacchione, T. Minoski, G. Rashed, M. Van Dyke, M. Murphy

"The National Institute for Occupational Safety and Health (NIOSH) has previously established pillar design guidelines for the underground stone mining industry. These guidelines were created from an empirical database of pillar observations and were largely drawn from shallow, flat-lying mining operations. Current trends forecast a great amount of underground stone mines developing under deeper cover, higher seam dips, and more frequent multiple-seam mining configurations than in the past. The complex loading conditions and limited experience in these environments presents a substantial increased risk of ground failure. To investigate these loading conditions, NIOSH has installed a pillar and roof monitoring system at an underground limestone mine in central Pennsylvania. The mine is operating in a seam with dips ranging from 13 to 18 degrees and overburdens ranging from 275 m (900 ft) to 425 m (1,400 ft). Instrumentation installed in an undeveloped pillar and in surrounding strata is currently measuring pillar and roof behavior in response to stress redistribution during excavation. Laser scans are being used to measure ground displacement and changes in conditions associated with local mining conditions and significant geological features. Initial stress measurements show a gradual increase in stress in response to mining, and stress changes that correspond with blasts. The seismic system is operational, with calibration events signaling on each of the 18 sensors. INTRODUCTION Improving mine-wide ground control stability can help reduce the potential for catastrophic failure of underground structures. The National Institute for Occupational Safety and Health (NIOSH) has conducted prior research in stone pillar design and has established fundamental pillar design guidelines for the underground stone mining industry, which resulted in the development of the S-Pillar program (Esterhuizen et al., 2011; Esterhuizen and Murphy, 2015). The data that constitute the S-Pillar program were derived from past mining experience that was almost exclusively drawn from shallow, flat-lying, single-level mining operations1. Stakeholder interactions with NIOSH researchers have indicated that increased numbers of underground stone operations are expected to mine under significantly deeper cover, with greater seam dips, and under multi-level operating conditions (Slaker and Murphy, 2016). The complex loading conditions and limited experience in these challenging environments present a substantial increased risk of ground failure. Inadequate pillar design in these new and challenging environments could result in catastrophic wide-area pillar collapses and an increased safety burden to miners working in the U.S. limestone mining industry. To develop design guidelines and prevent inadequate pillar designs for these challenging environments, NIOSH is currently conducting detailed pillar response investigations at case-study mine sites operating in challenging environments."

Jan 1, 2018

By A. E. Sears

The intent of geomorphic landform design is to mimic the function of the natural landscape. In a surface mine reclamation application, geomorphic landform design has the potential to mitigate stream loss. This research quantified features of reference landforms and performed computer modeling of a conceptual valley-fill design using geomorphic landform principles. A design was created using published design parameters with a software design tool (Carlson Natural Regrade with GeoFluv). Three additional designs, incorporating field-obtained regional geomorphic landform parameters, were completed and resulted in a geomorphic landform design specific to southern West Virginia. This work illustrates the importance of field determination of the ridge to head-of-channel input and drainage density parameters. Values of ridge to head-of-channel distance measured in this study were consistently an order of magnitude greater than software recommended values (SRV); SRV = 24 m (80 ft) versus field= 220 m (720 ft). Similarly, for the drainage density parameter, the software recommended range is 6 to 9 km-1 (80-120 ft/ac). The field measurements for central Appalachia quantified the drainage density to range from 5 to 5.3 km-1 (67-70 ft/ac). This affects Appalachian valley-fill stream construction by making the stream lengths shorter and the land slopes steeper with straighter headwater channels compared with areas in the southwestern United States. While the application of geomorphic landform design to surface mine sites presents challenges, this work provides support for future applications.

By Taner Aydogmus

The A$29 billion Chevron-operated Wheatstone Project is one of Australia’s largest resource projects. Located at Ashburton North, 12 kilometers west of Onslow in Western Australia, the project will consist of two Liquefied Natural Gas (LNG) trains with a combined capacity of 8.9 million tons per annum and a domestic gas plant. The LNG Plant will serve the offshore gas fields, which are situated some 250 km off the coast of Onslow in Western Australia. Once operational and on-stream, the Wheatstone Project will contribute to Australia becoming the world’s second largest exporter of LNG. For crossing the environmentally sensitive shore area, a micro-tunnel with an internal diameter of 2 m and approx. 1,242 m in length has been constructed by means of the pipe-jacking method. The micro-tunnel will accommodate a 1.1 m diameter pipeline (trunkline) to deliver gas from the offshore fields LNG Plant. The Wheatstone shore crossing design involves a number of unique challenges owing to its coastal location, where the alignment crosses through a shore area and terminates in a marine environment. This paper provides an overview of the Wheatstone Shore Crossing Project, presents the key features, and discusses the main aspects of the micro-tunneling design.

Jun 13, 2021

By J. W. Hawkins, K. B. C. Brady, M. W. Smith

The Pennsylvania Department of Environmental Protection (PaDEP) has been issuing surface mining permits since 1984 that authorize remining in areas that will affect preexisting pollutional discharges. These permits require the mine operator to employ best management practices to reduce pollution loading from abandoned mine discharges. A total of 110 completed mining operations with 233 discharges were evaluated to determine the impact to water quality. Overall, acid loading from these discharges was reduced by 7, 200 kg (15, 900 lbs) per day or 61%. Metal loadings were also reduced. For acidity, 49% of discharges improved or were eliminated, 52% showed no significant change and fewer than 1 % got worse. Loading reductions resulted from a combination of reduced concentrations and lower flows.

Jan 1, 2003

By Sahendra Ram, Ashok Kumar, Rakesh Kumar, AMIT KUMAR SINGH, Dheeraj Kumar, Arun Kumar Singh, Rajendra Singh

This article offers an examination of a retreat mining method conducted at the Pinoura Mine in India from 2010 to 2017. The method is atypical for coal mines of India’s coalfields. The method executes depillaring in a single pass and does not require the formation of galleries and support installation in splits, thus, reducing the cycle time. A variety of observations are discussed throughout this work and emphasis is placed on field measurements and depillaring under weak roof (RMR = 40–45). This paper discusses design techniques, specifically the estimation of the snook (remnant pillar) size, and important practical observations after the fact. The execution of this method was eventually conducted in eleven panels.

Aug 4, 2020

By T. R. West

Planning for urban development in many locations is based largely on 0.10 factors, 1) soil conditions and 2) socio-political aspects of the region. A more widely based approach is necessary, however, if a complete and functional plan is to be obtained. Under this unified approach, the overall field of earth science is included in the planning process. As considered here, the earth sciences comprise a large segment of the natural sciences; that is, geology, pedology, geomorphology, reengineering geology and ground water hydrology. A number of shortcomings can develop when using the restrictive, two-factor approach for urban development planning. These deficiencies are discussed in the paper. The specific considerations for each earth science area are examined and land use considerations for various urban requirements reviewed in light of these specialties. To illustrate the potential of the unified or earth science approach, Tippecanoe County, Indiana is presented as an example. The current area planning system for Tippecanoe County is examined to determine how well it compares with the unified approach and some of the shortcomings of the current plans are discussed.

Jan 1, 1972

By C. L. Molina

The U.S. Geological Survey (USGS), in cooperation with the Bureau of Land Management (BLM), Geological Survey of Wyoming, and U.S. Bureau of Mines (USBM), will produce an estimate of the amount of available coal in an area about 55 Ian (35 miles) south of Gillette, Wyo., where the Wyodak coal bed is 8-27 m (25-90 ft) thick. Available coal is coal that actually is accessible for development under current regulatory, land-use, and technologic conditions. Local coal-development considerations include roads, ranches, railroads, pipelines, power lines, wildlife and archaeological sites, alluvial valley floors, cemeteries, and the Hilight oil and gas field and gas plant. Some of these considerations would be mitigated so that surface mining may proceed; others presently preclude mining in their vicinity.

Jan 1, 1995

By Christopher M. St. John, Tony F. Zahrah

Empirical and numerical methods are the two extremes of the tools available for the seismic design of subsurface excavations and underground structures. Both have their limitations: when relying on purely empirical methods directly relevant experience may be scant; site data may be insufficient to justify a comprehensive dynamic analysis. The primary purpose of this paper is to review the analytical tools available to the design engineer of subsurface excavations and underground structures. Particular attention is devoted to simplifed models that appear to be applicable in many practical cases.

Jan 1, 1985

By T. W. Meikle

Three nutrient amendments and a biological seed inoculant were evaluated for use in establishing vegetative cover on waste rock substrates. Randomized blocks were placed on three substrates. Treatments included two types of organic fertilizer, mineral fertilizer, Azospirillum bacterial inoculant, plus controls. The seed mix consisted of native grass species adapted to low nutrient conditions. Canopy cover has been monitored for three growing seasons. Results indicate: 1) two of three substrates support plant growth following amendment with organic fertilizers; 2) organic fertilizers increase cover substantially over mineral fertilizer; and 3) Azospirillum had no effect on canopy cover.

Jan 1, 1999

By A. J. Martin, M. J. Peoples, D. J. Adams, A. Opara

"The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium (Se). Nitrogen species are also found in association with coal-mining drainages mainly due to the leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal-mining environments in British Columbia. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains.Treatment to remove Se from coal-mining waste waters has proven to be challenging for conventional water-treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry.This paper's electro-biochemical reactor (EBR) technology provides a controllable and consistent supply of useable electrons to the microbes directly at a low voltage potential (1-3 V) and low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical and robust biotreatment system. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required.Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal-mine waste waters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia’s coal-mining waste waters.IntroductionSelenium in Mining. Selenium (Se) is a naturally occurring trace element, which is an essential nutrient in small amounts (Thompson and Robinson, 1980; Brown and Arthur, 2001). However, it is also toxic to aquatic life, birds, and humans at very low concentrations. A major concern with waterborne Se is the potential for its bioaccumulation in aquatic food chains, resulting in acute and/or chronic toxicity to fish, water birds and amphibians (Besser et al., 1996; Conley et al., 2009)."

Jan 1, 2015

By Sandy Worden

Coal mining companies in Australia are managing the high-consequence risks across their operations more effectively by using an interactive online risk management system known as Riskgate Developed by the Minerals Industry Safety and Health Centre (MISHC) at the University of Queensland, Australia, Riskgate contains detailed information about 11 high-consequence risk areas (called topics in the system) for opencut and underground coal mines (Table 1). The existing topics are: fires; strata control for underground mining; ground control for opencut mining; tires; isolation; collisions; explosions and explosives; manual tasks; and trips, slips and falls. Every Riskgate topic is focused on coal industry activities (mining, processing, transport and storage). The scope includes mine sites, lease areas and mine infrastructure (mobile, fixed plant, field equipment, buildings, road and rail transport), and all aspects of the mine life cycle from design through to decommissioning. The topics uniformly recognize that a loss of control can result in injury or fatality, equipment damage, production loss, reputation loss and environmental damage. However, the priority focus for Riskgate is the safety of mine personnel.

Jul 1, 2013

By L. K. Holder

"The Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), commonly known as Superfund, mandates evaluation of remediation alternative using nine criteria: (1) overall protection of human health and the environment, (2) compliance with ARARs (applicable or relevant and appropriate standards), (3) long-term effectiveness and permanence, (4) reduction of toxicity, mobility or volume, (5) short-term effectiveness, (6) implementability, (7) cost, (8) state acceptance, and (9) community acceptance. Many states have adopted these or similar criteria for remedy selection under state laws. Although not explicitly addressed in the CERCLA criteria, consideration of sustainability can be incorporated into these criteria. This paper explores how sustainability can be evaluated for remedy selection using the CERCLA criteria. INTRODUCTION Sustainability considerations can be incorporated into all phases of site remediation: • Site investigation (remedial investigation). • Remedy selection. • Remedial design. • Remediation construction. • Operations, maintenance, and monitoring. This paper focuses on remedy selection. Many have looked at remedy selection using sustainability criteria. However, CERCLA and corresponding State programs require remedy selection using mandatory criteria. This paper shows how sustainability can be explicitly considered using the mandatory criteria. REVIEW OF CERCLA CRITERIA First, we review the definitions of the CERCLA criteria. We then explore how sustainability criteria can be fit into the CERCLA criteria. Overall Protection of Human Health and the Environment This criterion addresses the degree to which each alternative is protective of human health and the environment, considering both long-term and short-term risks. Overall protectiveness is a ""threshold"" criterion, in that alternatives that do not achieve adequate protection of human health or the environment are eliminated from further consideration. Evaluation of this criterion is derived from the evaluation of the other criteria (e.g., long-term effectiveness and permanence, and short-term effectiveness). It is not an independent criterion, but more a summary of the overall evaluation."

Jan 1, 2015

By R. J. Zagrocki

Rekindled public concern about lead toxicity has intensified the awareness of lead-bearing materials in contact with the environment and the human population. Lead's common association with other metals makes the increasingly restrictive lead standards a primary concern for a large number of metal and metal-related industries. In commercial scale demonstration tests with lead-bearing wastes, the HRD Flame Reactor process has a demonstrated ability to separate and recover over 95% of the lead as a recyclable oxide, while rendering the remainder of the material as vitrified, non-leaching, and nonhazardous co-product. Recent Flame Reactor process tests and preliminary cost data for secondary lead soda slag are highlighted.

Jan 1, 1992

By Aaron Archer, James Parkes

This paper presents design considerations for the major underground elements of the pending BCRUA Phase 2 Raw Water Delivery System Project. These elements include two Lake Taps; an 8,800 LF, minimum 10-ft OD intake tunnel; a suction chamber with 6 Pump Shafts; a 30-ft diameter, 300-ft deep Main Shaft; a 2,600 LF Transmission Tunnel with 78-inch steel liner; and a 130-ft deep shaft on the Transmission Tunnel. The tunnels and shafts will be excavated through the Glen Rose limestone. The design development included consideration for technical requirements, easements, third party commitments, previous local project experience, and constructability based on contractor outreach.

Jun 13, 2021