Search Documents

By MARK J. VANARELLI

Estimating groundwater inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies for estimating steady-state groundwater inflows into deep rock tunnels. The case studies included the Chattahoochee and Nancy Creek tunnels. In this paper, statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations. A semi-empirical procedure was utilized for estimating groundwater inflows into these deep rock tunnels. It is the most widely used method/procedure in the tunnel industry. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels which exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semi-empirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Packer test data plotted in histograms were observed in all cases to be log-normally distributed for the radial flow condition. Modeling using Monte Carlo simulations was observed to be an effective tool for removing irregularities in the distribution of the data and incorporating high-end permeability data to derive reasonable groundwater inflow estimates. This paper is based on the PhD thesis entitled “Improvements to the Current State of the Practice in Steady-State, Groundwater Inflow Estimates into Rock Tunnels based on the Application of Statistical Analysis Methods of Packer Test Data obtained from Exploratory Borings During Geotechnical Site Investigations.”

Oct 9, 2020

By C. J. Weiss

"A commercially available Through-the-Earth (TTE) communications system was evaluated at an underground coal mine in eastern Kentucky. This field study was conducted as part of a larger multi-site evaluation of available TTE systems to determine their operational sensitivity. Field testing is being performed along with simulation techniques developed for geophysical surveys. The results of the field test will additionally be used to determine the applicability of these simulation techniques to TTE communications. The mine detailed in this paper was idled at the time of the study, which provided the nearest practical representation of a post-event mine shutdown. For this study, the three following communication modes were tested: surface-to-underground, underground-to-surface and surface-to-surface. Standard deployments of the TTE system using the manufacturer’s recommended procedures were able to achieve clear communications between underground and surface locations. Other arrangements of the units yielded intriguing results, some of which were predicted by computer simulations, others were unexpected. Future experimentation is planned to further evaluate the observed phenomena. INTRODUCTION The ability to establish effective communication between surface and underground personnel after a mine event is essential for both mine evacuation and mine rescue efforts. Current communication technology is reliant on physical infrastructure, such as antennas, cables, and repeaters, located throughout the mine. Such systems are easily disabled during a mine event because of their vulnerability to physical damage. A true emergency communications system would have the ability to function regardless of a mine’s physical state. Through-the-Earth (TTE) wireless communications technology has the potential to provide such a tool. Wireless TTE communications are exceptionally challenging because electromagnetic (EM), or radio, signals are subject to drastic attenuation as they travel through solid strata. In addition to attenuation, EM wave propagation is directly affected by the physical and petrographic characteristics, mineral compositions, metamorphic properties, and the degree of water infiltrations in the strata [1-5]. These strata characteristics are unique to each mine thus making the design of an effective, universally deployable, and reliable TTE communications system very difficult. At present, TTE technology is in the preliminary stages of practical deployment with only a few permissible TTE systems commercially available."

Jan 1, 2015

By Robert G. Beverly

The presence of radioactivity in uranium mill wastes has resulted in somewhat unique waste disposal methods. In addition to the common problems of disposing of large quantities of solid wastes, neutralizing acids, minimizing dissolved heavy metals, and clarifying all liquid effluents, the uranium mill operator must sample and analyze liquid effluents for micro-micro quantities of radionuclides such as, radium-226, thorium-230 and lead-210. Special disposal methods or decontamination procedures are required to meet the stringent limitations established by the U. S. Atomic Energy Commission on the concentration of radionuclides in liquid effluents. Routine monitoring of the receiving stream is also normally required. In recent years there has been a growing concern about the radioactivity remaining in the uranium mill tailings, particularly at the sites of shut-down or dismantled mills. The State of Colorado, in cooperation with the industry, has adopted regulations for stabilization of inactive uranium mill tailings. The Mining and Metals Division of Union Carbide operates mills for the recovery of uranium and vanadium at Uravan and Rifle in Colorado and a mill in the Gas Hills of Wyoming for uranium production. The company also owns former mill sites on which mill tailings are located at Maybell, Rifle, and Slick Rock in Colorado and at Green River, Utah. The purpose of this paper is to describe the methods used by a few uranium mills, largely those operated by Union Carbide Corporation, to dispose of radioactive wastes, to discuss briefly the regulations under which the mills operate, and to present reference information on the subject.

Jan 1, 1968

By Kevin Andrews, Zach Agioutantis

Analysis of Coal Pillar Stability (ACPS) software, released in 2018, integrates numerous empirical pillar design techniques. The ACPS program incorporates methodologies originally available as design tools from the National Institute for Occupational Safety & Health (NIOSH), including Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Analysis of Multiple Seam Stability (AMSS), and concepts including Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar formula, and pressure arch loading. The design methodologies that are the basis of ACPS were developed via analysis of significant amounts of real-world data and have been standards of the United States coal industry for decades. While there are empirical factors built into ACPS, making it ideal for use in U.S. coalfields, the concepts in the program have proven to be applicable in variable mine settings, and the software was developed to allow for user-based, site-specific modifications of key design inputs. Application of ACPS to cases outside the regions for which it was developed must be approached carefully, and continuous development of site-specific data is mandatory. A case study is presented involving the application of ACPS to assess pillar stability and assist future design for an underground lignite mine in Eastern Europe. Assessment of in-mine observations, review of the geology of the lignite mine, and evaluation of specific conditions associated with a failure event resulted in “calibration” of key input factors to ACPS. Scenarios evaluated with ACPS suggest that pillar strength and overburden depth are key factors for the determination of pillar stability and design in future areas.

Jun 25, 2024

By T. BoBo

"In the 1990’s metal prices were trending in a long term decline and the usual cost cutting exercises were adopted. Cuts to research and development made innovation difficult and the outlook was grim. But necessity is a strong motivator, and these conditions spurred the Mine-to-Mill movement which optimised across organisational “silos” and utilising new technology tools, innovative software and increased computing power. Many applications of Mine-to-Mill exploited the fact that comminution is usually the site processing bottleneck, and that blasting is more efficient at breaking rock than grinding. This approach sought to: • Understand and characterise rock breakage from mining to the mill • Develop models and simulators for blast design, fragmentation, crusher and mill circuits • Develop tools to measure in real time the particle size distribution of rocks on conveyors and Run of Mine (ROM) muckpiles • Ensure effective communication across the silos between geologists, blast design engineers, mining engineers and metallurgists These methods and the technology tools available in the 1990s were widely adopted at numerous sites around the world with significant benefits. SAG mill throughput increases of 10-20% were common. This was the advance the industry desperately needed. It was low capital cost; it was obvious. It was here to stay. Except, in too many cases, it didn’t. In the minerals price boom of the 2000’s Mine-to-Mill was no longer necessary to “survive”, even though it was still good business. Some operations, including some of the early success stories, slipped back to old habits of optimising within organisation silos instead of across them. Fortunately, other operators still embraced Mine-to-Mill and developed new techniques. Mine to Mill was still successful, but it not as widely adopted as we had expected it to be.Now the boom has ended and operations are again under cost pressure. Since these are the same circumstances that created Mine-to-Mill, it seems time to achieve the wider adoption. Since the 1990s many new or advanced technology tools are available for Mine-to-Mill projects: blast-hole sensors, new explosives formulations, new blasting techniques and modelling, ore tracking devices, improved image analysis to determine size, texture and colour of coarse ore, grade sensors, whole-stream simulation tools, even more powerful computing hardware and data analysis software. If we could achieve so much in the 1990’s, how much more can we achieve today when we have the same imperative, the same potential and a larger number of high technology tools?"

Jan 1, 2017

By E. B. Kroeger

Spoil instability has been a problem at a coal mine in interior Alaska. Parameters such as original site topography, groundwater conditions, material properties, spoil-pile geometry, geology, permafrost, natural slope instability, changing weather conditions, and dense, near-surface vegetation have interacted to produce unstable slopes. Several failure modes have been identified including deep seated earth block slides, bimodal earth flows, and solifluction. Thawing of permafrost also created conditions where sliding of spoil along the interface separating the spoil and the natural ground surface occurred when the cohesion and the friction angle of that zone was reduced to zero and below 15?respectively.

Jan 1, 1992

By P. James

"INTRODUCTION Control of target stream acidity is widely used in MIW (mining influenced water). Tailoring pH (a measure of acidity) finds application for controlling key chemistry in both process and waste streams. Traditional lime addition for neutralization and precipitation is most often used but has high reagent costs and results in large amounts of mixed metal sludge requiring costly disposal. A new adaptation of BPS’s patented DEMET™ technology (Dynamic Electrolytic Metal Effluent Treatment) platform offers a potentially improved and “reagentless” alternative to traditional chemical addition for pH adjustment. Electricity rather than chemical addition utilized in BPS’s proprietary approach controllably tailors target stream pH. The method offers a simple, low-cost processing technique yielding cleaner treatment chemistry. BPS’s “green” approach may yield lower operating (OPEX) and life cycle costs and significant reductions (up to 50%) in sludge generation compared to conventional lime treatment. It can also allow new opportunities to generate revenue via selective recovery of valuable processing byproducts. Specific savings and revenues depend on the target site chemistries, details, and processing goals. A more detailed discussion of the process and its operational principles may be found in Reference One.[1] Here application of the BPS treatment to POx (Pressure Oxidation) leaching as an alternative to traditional chemical addition is examined. An example operation process flow for gold mining is considered.[2] Promising processing points for potentially replacing conventional processes with DEMET are noted. The possibilities for lowering OPEX costs, lessening sludge creation, and capturing various valuable byproducts and residuals are examined. Financial life cycle benefit estimates of the principal gains provided by DEMET application to the example operation are noted. Extension and generalization of the analyses to a wider range of scenarios is explored."

Jan 1, 2016

By D. Anderson Willis, Alan A. Campoli, Douglas Mynear, Seth Mittle, J. Steven Gardner

"The diversification of energy sources in the United States has seen some major shifts during the past decade resulting from:• A sudden abundance of low-cost natural gas becoming available through advanced horizontal drilling and hydraulic fracturing techniques.• Incentive-driven policies leading to new development in alternative energy.• The emergence of alternative energy sources proliferated as a result of state and federal level incentives and falling capital costs.Coal was once recognized as the primary low-cost fuel source for the generation of electricity in the United States for most of the last century, providing upward of 50 percent of the total generation capacity during much of that period. However, within the past decade, lower-cost natural gas has overtaken coal as the primary source of fuel used in electricity generation, and alternative sources have steadily grown to now account for approximately 10 percent of the overall mix.West Virginia and Kentucky have not experienced the full breadth of the fuel shift, and, as of 2016, still obtained approximately 80-90 percent of electric power generation from coal. However, as coal plants are retired, there has been a shift toward natural gas for new power plants constructed in the region. The economics of power generation (i.e., lowcost fuel source) has typically been the major factor in determining shifts from one fuel source or technology to another. However, governmental energy policies and incentives have more recently been used to promote the development of new alternative technologies such as wind and solar energy growth to diversify the energy mix. The implementation of these incentives has provided some needed traction and resulted in driving the cost of manufacturing and installation of these new wind and solar systems downward to be more cost competitive with conventional fossil-fueled power sources. Future shifts in the generation capacity by fuel type will also be inevitable and impossible to project accurately as policies change and innovative technologies evolve. Determining factors may include the expiration of current incentives, decreasing capital costs, future environmental regulations, evolution of energy storage systems, technical challenges associated with increasing intermittent sources of generation and the development of unforeseen technologies. West Virginia and Kentucky have been among the least solar friendly states, ranking 44th and 48th of the 50 states (Fig. 1 for WV). The ranking of other coal producing states are similarly low:• Ohio 20• Pennsylvania 21• Virginia 38• West Virginia 44• Wyoming 45• Kentucky 48• Alabama 50"

Jun 1, 2019

By R. K. Steinhorst

Multivariate cluster analysis, MANOVA, canonical analysis, and discriminant analysis of hydrochemistry data were used to investigate the directions of ground water movement in basalts in the vicinity of the Hanford Reservation, Washington. The statistical analyses indicate that the hydrochemistry of the ground waters in these basalt formations is distinctly different on each side of the Columbia River. This suggests that the river is a ground water divide or that the river is roughly coincident with a hydrogeologic barrier boundary. The statistical procedures used in this study constitute a quantitative means for differentiating ground waters according to hydrochemistry.

Jan 1, 1990

By Donald R. East

In the planning and design of mill tailing disposal facilities, the chemical and physical nature of the fine­grained material to be disposed of has to be fully understood in order to create an efficient and safe long­term storage facility. Disposal of tailing has become the single most important source of environmental impact for mining projects and the development of many promising ore bodies has been delayed or even stopped due to problems of facility siting and design under pressure of increasingly stringent regulatory require­ments.

Jan 1, 1992

By Martin Oatman, Lawrence Lenahan

The West Seattle Tunnel is part of a regional sewer conveyance system located in Seattle Washington. The tunnel was constructed for the Waste Water Treatment Division of the King County Department Of Natural Resources, from June of 1995 through the first quarter of 1997. The Geologic setting for this soft-ground tunnel consists of glacial, interglacial, glacio-lacustrine, and alluvial soils. This paper, prepared jointly by the owner and con-tractor, will describe project-related site geology, engineering considerations, construction, and dispute resolution/avoidance practices.

Jan 1, 1997

By S. Behl

In the selective flocculation process, polymers with specific functional groups can yield highly selective adsorption and, therefore, high separation efficiency. Selectivity in polymer adsorption may also be attained by specific additives that inhibit the adsorption of the flocculant on some solid surfaces but not on others. Generally, these additives have a different chemical nature than the flocculant. In this study, the lower molecular weight fraction of the flocculant was successfully evaluated as a site blocking agent, leading to higher separation efficiency than obtained otherwise.

Jan 1, 1993

By D. Lelinski, X. Nie, J. D. Miller, J. Hupka, K. Bukka

A preliminary characterization of soil components contaminated at a low level (7 nanocuries per gram) with toxic/radioactive metals has been carried out. Most radioactivity and metals content were present in the minus 100 mesh (<150 µm) size fractions. None of the size fractions examined qualified for uncontrolled disposal at dump sites, thus all material would have to be moved to discharge-controlled landfills. The metal content of the sample was below the limits for economical recovery, therefore eventual processing would be dictated by environmental concerns.

Jan 1, 1992

By Dave Rogstad

The DART NC-1B Tunnel Project consists of two 5,100 m TBM excavated tunnels, a principal underground station, a partially completed future station, a surface station, and eight associated ventilation shafts and exit tunnels. This paper presents a case history of the project&apos;s construction, and will focus on six topics that give this project a unique and unusual history; the TBM excavation, two major differing site conditions, roadheader excavation, polyfiber reinforced shotcrete lining, the NATM design geometry, and a design/build type of contract.

Jan 1, 1995

By F. G. Boehm, T. S. Golosinski

This paper identifies the components of belt conveyor shifting force as a vertical force, Pv, a lateral force, Ph, and a longitudinal force, Pl. A method for estimating these forces is proposed that relates each of their values to the properties of the conveyor structure and rails, the shifting operation parameters, and other site-specific conditions. The effect of this force on the shifter behavior is analyzed, and guidelines are developed for selecting a suitable shifter. As well, other equipment requirements for the shifting operation are discussed.

Jan 1, 1988

By Paul C. Schmall, John F. Donohoe, Arthur B. Corwin

In the aftermath of the September 11th attack on the World Trade Center, groundwater control was of immediate concern. Water in?ow from the adjacent Hudson River through the compromised slurry wall ‘bathtub’ surrounding the site, ruptured water and sewer mains, and saturation from fire hoses all contributed to an already critical situation, further hampering the recovery and rehabilitation effort. An extensive pumping and deep well installation program was initiated, focused on reducing the hydrostatic loading to the severely damaged perimeter slurry wall.

Jan 1, 2003

Raises are widely constructed underground in hard rock mining for ventilation, material transport or emergency escape. The four major raise excavation methods, Drop Raise, Conventional, Alimak and Raise Bore can be divided into two categories from ground control point of view, one ground support can be installed during excavation, the other not. Excavation method must be chosen carefully to keep the raise wall in stable state during excavation and make sure enough rock stand-up time to install ground support if needed. If rock quality is permitted and there is no strict space limitation, raise bore method which is the only method that ground support can not be installed after the whole excavation is finished should be considered first because it is faster, cheaper, safer and less disturbance to the hosting rock. Support may or may not be needed depends on the purpose of the raise and rock quality. In high quality hosting rocks, if the raise is only for ventilation or material transfer, support may be not needed. If it is for emergency escape or escape and ventilation, which provide or require personnel access, the whole raise must be supported either in high or low quality rock. Based on on site data collection, construction and raise utilization, this paper gave out the rule of thumb how to decide an excavation method. After purpose of the raise, required raise diameter (size) and raise site options being known, geotechnical data collection is the next important step in a raise project.

Jan 1, 2011

By James J. Brady

The basic story at Bear Swamp was how to excavate an underground chamber 79 feet wide by 227 feet long and 150 feet high, along with the related access, tarbrace, leads, power tunnels and shafts, do it under cost and ahead of schedule and still have just about everybody love you. The isometric sketch of the overall project follows. I won&apos;t go into any of the details of the physical scope at this point. Instead, we&apos;ll bring out the sizes, grades, particular problems of the different areas as we cover them. First of all, let&apos;s establish that Bear Swamp was a Target Estimate - Fee with Incentives type of contract. Gates and Fox&apos;s contract was with the project&apos;s general contractor, J. A. Jones. We were one of three contractors who submitted proposals and estimates to Jones. After much negotiation and many submittals, Gates and Fox was notified we had been selected to do the underground excavation on April 12, 1971. We had our first people back on site in two days, set up a temporary office, made our first steel order for jumbo erection, pacing our jumbo construction to meet the date when J. A. Jones would have the access portal ready for us. The shops, yards, dry house, compressor building were all erected as sites were designated for our use. At last, on Thursday, June 3, we trimmed the face and moved our 9-machine Euclid jumbo up a hastily constructed haul road and started our portal preparation of the access tunnel.

Jan 1, 1974

By Donald K. Sparling, C. Edwin Baker

The White Mesa uranium/vanadium mill is six miles south of Blanding, UT, on the Colorado Plateau, which has historically spawned more than 200 uranium mines. As uranium prices approached an all-time high during the mill planning period, Energy Fuels Nuclear Inc. anticipated the reopening of many of these mines, whose low grade ore suddenly looked economic. The company located the White Mesa mill close to these mines, to minimize hauling distances to the mill and give vendors added incentive to reopen or expand mine operations. A receptive local community, a relatively unencumbered trip through the regulatory maze, and some mill circuit innovations all helped to make the White Mesa mill a well functioning reality. From a strategic standpoint, and to begin ore stockpiling as early as possible, Energy Fuels constructed two ore buying stations and began receiving ore in early 1977. The buying stations were located at Hanksville and at what is now the Blanding mill site. Ore receipts at Hanksville did not materialize as anticipated and the facility has since been closed. The Blanding ore buying station is now an integral part of the milling operation. All ores, whether company, vendor, or for toll milling, are received at the Blanding station. The Blanding site was central to the plateau mines, and was well received by area residents, who encouraged the introduction of industry to the area. Residents viewed mill construc¬tion as an economic blessing and were prepared to accept the associated im¬pacts. Energy Fuels hired as many local people as possible for mill opera¬tions.

Jan 4, 1981

By E. Koufetzis

Rock mass classification systems are core elements of tunneling and empirical mine design worldwide. The Bauxite division of S&B Industrial Minerals S.A. decided to implement a rock mass classification system in order to provide mining engineers and supervisors of the underground mines, with guidelines of stability performance and with a complementary tool for the selection of the appropriate tunnel support. The back analysis system employed is based on visual observation of especially selected underground mine sites, representative of all rock types. This fact combined with the failure or success of the already existing support system, constitute the fundamental part of the work undertaken. The paper is divided into three main parts. In the first part the classification methods of Q, RMR89 and GSI are presented and the advantages and disadvantages of each method in connection with underground mining are indicated. RMR89 and GSI are conclusively selected for use, the main criteria for the selection being, the simplicity in use and the competency of the support system suggested for each rock mass category. The second part points out the methodology for measurements, the practical difficulties encountered during this process and the guiding principles followed, in order to avoid these problems. In the third part, the final conclusion of this project is demonstrated and the different rock mass categories are presented with their relative support recommendations, as they were applied and tested in all phases of the bauxite mines? exploitation. The generated methodology is being implemented by the site mining engineers, for validation and potential improvement.

Jan 1, 2008