Search Documents

By Y. Luo, S. S. Peng, C. T. Holland

Introduction A well-designed mining plan is one that minimizes cost and mining induced problems and maximizes recovery of the coal reserve. To minimize the negative effects on surface structures caused by ground subsidence due to underground mining activities, two kinds of practices are commonly employed by mine operators. One is the support technique, which leaves an area of coal unmined or partially mined beneath the structure to be supported. The other is the protection technique, which protects the structure when it is subsiding with the ground by taking advantage of the ground subsidence process (Luo et al., 1992). In designing the supporting technique, the only currently available method in the US is the one stated in the Pennsylvania Underground Coal Mining Rules (1985). However, the size of the support area designed by this method will be excessively large and result in a wasteful use of coal reserves when the overburden depth is more than 350 ft. A more scientific method is proposed in this paper for designing the support area. This method is based on a large amount of subsidence data collected throughout a number of major US coal fields and the authors' experience with monitoring and protecting surface structures that have been undermined by longwall panels. It considers the critical deformation indices that a structure can tolerate, and depth and height of underground extraction. A support area designed by this new method will not only assure the safety of the structure to be supported but will also maximize the extraction of the coal reserve. Design of support area using the Pennsylvania rules The Pennsylvania Underground Coal Mining Rules (1985) state that no underground mining activity should be permitted beneath structures where the overburden depth is less than 100 ft. An exception to these rules is provided for mine related openings that provide access to the surface for such as entries, shafts, boreholes and site-specific variances for entry development. If the overburden depth is greater than 100 ft, the mine operators should utilize either of the following: •Extraction techniques that provide for planned subsidence in a predictable and controlled manner, or •Support techniques designed to prevent subsidence damages to features identified as: •Public buildings and non-commercial structures [ ] customarily used by the public, including churches, schools and hospitals • Dwellings, cemeteries, municipal public service operations and municipal utilities in place on April 27,1966 •Impoundments and other water bodies with a storage capacity of 20 acre-ft or more • Aquifers, perennial streams and water bodies that serve as a significant source for a public water supply system, and •Coal refuse disposal areas. The support techniques require that a support area be left beneath the surface structure or feature to be protected (Fig.1). The support area should consist of coal pillars, with their size and pattern being such that their bearing strength is maximized. The total coal extraction within the support area should be limited to a maximum of 50%. The support area should be rectangular in shape and determined by projecting a line at a 15° angle from the surface to the coal seam with an offset distance of 15 ft from all sides of the structure. For a

Jan 1, 1994

By Dale S. Preece

INTRODUCTION The Waste Isolation Pilot Plant (WIPP) is a research facility located in Southeastern New Mexico. The WIPP is being developed by the U. S. Department of Energy (DOE) to demonstrate the safe storage of defense-related radioactive wastes in bedded salt. Since the WIPP is a research facility. a number of large-scale in situ experiments have been planned and are currently under construction (Munson, 1983). These experiments were designed to study various aspects of nuclear waste storage in bedded salt such as mechanical responses and creep closures of drifts, thermal response due to heated canisters, and thermally-induced fluid migration. One purpose of the WIPP is to develop and demonstrate a general predictive structural analysis capability for a bedded salt repository. One set of experiments, called the Geomechanical Evaluation (Room G), is heavily instrumented to study the creep around several rooms with different configuration. A Layout of the Geomechanical Evaluation room is shown in Figure 1. One portion of it consists of wedge shaped pillar where two drifts intersect at an angle of 7.5 degrees. The pillar can be seen at the bottom of Figure 1. One purpose of the wedge pillar experiment is to study progressive pillar failure in the tip region. Another is to determine how nonuniform pillar thickness affects creep closure of the drifts. An important aspect of the experiments is the correlation between experimental data and corresponding pretest finite element analyses of the site. The finite element simulations serve two purposes. First, the computer simulations aid in understanding the experimental results by providing calculated stress. strain and displacement fields that cannot be measured directly. Second, comparison of calculated and measured drift closures serves as a method for validating or improving the finite element models and the constitutive models employed. The wedge pillar geometry required a 3-D finite element creep calculation. Results from these 3-D calculations will be presented in this paper. A 2-D plane strain double drift model which approximates the wedge pillar geometry at a slice perpendicular to the drift has also been performed and will be compared to the 3-D results in this paper. FINITE ELEMENT COMPUTER PROGRAMS Two finite element computer programs. JAC (Biffle, 1984) and JAC3D (Biffle. 1986), were used. JAC is a 2-D finite element program developed for quasi-static analysis of non-linear solids. It employs the conjugate gradient iterative technique to obtain a solution Spatial integration is performed using a single gauss point in each four node quadrilateral element. An hourglass viscosity technique is used to control the zero energy modes that occur with single point integration. The single point integration combined with the explicit nature of the program and exploitation of CRAY-1 computer architecture results in very efficient execution J4: results were compared to results obtained with eight other 2-D structural creep computer codes in the second WIPP benchmark exercise (Morgan, 1981) JAC3D was derived from JAC to treat 3-D finite element models and has many of the same characteristics including single point integration and hourglass viscosity. These characteristics have made 3-D creep analyses more reasonable by significantly reducing computation time The first exercise of the creep capability

Jan 1, 1986

By A. B. Cecala, G. W. Klinowski

Introduction The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour (acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec (50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average millwide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al., 1987). Testing Total mill ventilation systems were evaluated at two processing operations. For both tests, the primary goal was to determine the reduction in respirable dust throughout the structure. Test site No. 1. The first evaluation was performed at a clay-crushing and screening mill in New York. The mill's base dimensions were 39.6 x 9.8 m (130 x 32 ft), giving a volumetric capacity of 4250 m3 (150,000 cu ft). The TMVS was designed to provide 12 m3/sec (25,430 cfm) of ventilation air to the mill, representing about 10 acph. This was accomplished by three 4 m3/sec (8475 cfm) roof-powered exhaustors that were evenly spaced across the roof. Three wall louvers provided inlets for make-up air at the mill's base. Two evaluations were performed at this mill. The first occurred for two days in December when outside air temperatures ranged from -12.2° to 4.4° C (10° to 40° F). Temperatures with the wind chill factor dropped as low as -34° to -40° C (-29 to -40° F) during the early morning. The second evaluation was in April when outside air temperatures ranged between 10° to 26.7° C (50° to 80° F). These two evaluations verified the effectiveness of TMVS in lowering respirable-dust concentrations throughout the mill. Gravimetric-sampler respirable-dust concentrations in December ranged from 0.22 to 2.39 mg/m3 under normal conditions, compared to 0.13 to 1.55 mg/m3 with TMVS. In April, respirable dust concentrations ranged from 0.29 to 4.84 mg/m3 under normal conditions compared to 0.21 to 2.37 mg/m3 with the system on. TMVS also increased visibility throughout the mill building. Dust reductions for gravimetric and RAM-I instruments are listed in Table 1. Each value was determined by comparing the average concentration for the entire day of testing for normal and TMVS values. The mean/standard deviation values for gravimetric and RAM-1 results were 42.5/17.6 and 37.1/16.8, respectively.

Jan 1, 1996

By Wallace W. Roepke, James C. Church

Introduction The history of mining machine development has been and is one of "bigger is better." While this may not always be true, it is currently the only approach open to machine designers without specific in situ cutting force information. The US Bureau of Mines has tried to modify this approach by supporting research, both in the laboratory and in field tests, that demonstrates that bigger is only better if the equipment is used correctly. In-house research has shown conclusively that deeper cutting reduces both dust and energy (Roepke, Lindroth, and Myren, 1976). This approach has been applied to a large Lee-Norse (LN456) continuous mining machine, which confirmed that slow deep cutting is beneficial and does not have a negative effect on production (Black and Rounds, 1977; Black et al., 1978). Specific in situ engineering data needed on coal cutting forces have not, however, been obtained by field tests with the LN456. Although the machine was instrumented to obtain data on one seam, it would be impractical to move the machine from mine to mine. It became apparent that a portable, easy to use device was needed for obtaining coal cutting forces in situ. Such a device could provide the engineering data needed by manufacturers, the site-specific cutting information needed by operators, and a field research tool to establish correlation with laboratory cutting tests. Design and Development According to a set of design guidelines established by the Bureau, the proposed device should be able to measure cutting forces directly with standard coal cutting bits, be transportable by two miners, and be self-contained. These guidelines were given to Ingersoll-Rand Research Inc. (IRRI). The contractor performed a rigorous review of 16 existing in situ portable tester designs, none of which could use a standard coal cutting bit to measure cutting force directly. These included a wide range of devices, all of which are discussed in the final report (Banerjee and Wisner, 1982). A series of design tradeoffs were established to satisfy initial design guidelines. The final deci¬sion was heavily weighted by an industry survey to determine the preferred concept from four man¬ufacturers and four operators. To assure ease of use with maximum information, all respondents wanted a linear cutting device that could work in seams down to 1 m (40 in.). The final design choice was between a linear and a rotary tester. The rotary tester would cut on an arc in the same manner as a rotary drum machine. It had several faults, however, that could not be resolved within the scope of this contract. The worst was related to arc cutting (Roepke, Lindroth, and Myren, 1976). Since any bit cutting on arc enters the coal at zero depth, goes to maximum depth only at the horizontal centerline, and exits at zero, maximum cutting force is obtained only at the instant the bit crosses the horizontal centerline. This centerline peak response would require that many replications be made with an arc-type cutter to get reliable force information. The arc-type tester would require extensive face preparation to establish the cutting path and extensive wasted clearing cuts to advance the device for additional layers of cuts. The linear tester could be mounted directly on any face or rib with only minor preparation. By its nature, a linear cut at a constant depth provides multiple peak force data over the length of the cut, thus reducing the required number of replications. The final review of these two major design concepts plus indus-

Jan 9, 1983

By Wallace W. Roepke, Richard C. Olson

To adequately attack the longwall dust problem, the US Bureau of Mines funded a contract to define dust sources on a longwall mine face area. The study examined the shearer during sumping, cutting, and tramming, the conveyor, and the roof supports. Tests showed the shearer to be the major dust source. Introduction Long-term illnesses place a heavy burden on miners, the mining industry, and taxpayers. Black lung payments to more than 400,000 miners and their survivors exceeded $9 billion between 1970 and 1980. They are continuing at a rate of $1 billion per year. Recent MSHA data indicate more than 50% of the longwall faces are still out of compliance with the 2 mg/m3 (0.00007 oz per cu ft) respirable dust regulation. Allowable dust limits are often further reduced owing to the presence of silica dust. This substantially increases the problem's severity. Research in the 1970s showed that by modifying the mining method through changing drum-type mining machines from high rpm shallow cutting to slow rpm deep cutting, both specific dust and energy could be reduced (Black et al., 1978; Ludlow and Wilson, 1982; Roepke, Lindroth, and Myren, 1976). The coal mining industry is using more longwall equipment to economically obtain high productivity. This high production rate, however, makes it difficult for longwalls to meet the legal dust standard. Research is showing how both these concerns may be addressed at the mining face. Results reported here explain the relationship of various major elements of the longwall system to dust generation on the longwall face. This paper is based on work completed by Foster-Miller Associates Inc. Objectives were to differentiate dust sources on the longwall face and to quantify dust levels for various elements of the shearer drum. The work was accomplished in two phases. Jonathon Ludlow, project engineer for FMA, developed and performed the necessary testing (Ludlow and Marshall, 1983). Bradley, Hadden, and Weston (1983) have done evaluations on British coal mines that produced similar results to those reported here. They found causative rela¬tionships between haulage speed, production, depth cut, drum speed, and dust generation. They also found that roof support movement increased the dustiness, whereas this work indicated that support movement had only a minor effect on total dust exposure. Both of these results are valid when the variation of mining conditions is analyzed. British mines are deeper than US mines. Therefore, roof rocks and coal are more fragmented than in the shallower US mines. Other reasons for the dust differences include the weaker shales found in Britain and the variation of roof support equipment designs between the UK and the US. Four mines in this report had rock roofs and, thus, would be less dusty. The fifth longwall mine had a coal roof, but the large cross-sectional area and high air velocity minimized dust exposure. Mines and Equipment Five underground longwall mine sites were tested (Fig. 1). All were using double-ended ranging-drum shearers (derds) with some variations in equipment. The mines and equipment details are shown in Table 1. No modification of mining equipment or operating cycles was made during the first phase of testing. The mining process observed followed the normal mine operating procedures. Three GCA RAM-1 respirable dust monitors and two vortex anemometers with cycle notations on portable tape recorders were used in each face area. The start and end of each cycle segment were recorded. Dust monitors record the dust levels once every 10 seconds, thus providing a relatively continuous real time indication of change in

Jan 8, 1984

By G. R. Laurer, J. W. Neton, C. Pomroy, N. Cohen, M. Eisenbud

INTRODUCTION In uranium miners, a causal relationship between exposure of the lung to high levels of alpha radiation and the consequential induction of bronchial carcinoma is now well-established (Wagoner, et al., 1965). Quantitation of this cause-effect association presents considerable difficulty, however, as the result of various confounding factors such as the contributing effects of smoking and/or arsenic exposure (Archer, Gillam, and Wagoner, 1976), normal metabolic variability and, perhaps most important of all, the absence of accurate radon/radon daughter exposure data. Estimates of cumulative lung exposures suffer from inaccuracy due to critical factors such as 1) unknown ventilation rates; 2) difficulties in obtaining representative mine air samples; 3) the variable character and magnitudes of the exposure sources; and 4) specific differences in metabolism and job histories that exist among miners. It was with considerable enthusiasm, therefore, that investigators readily embraced the idea of using skeletal burdens of the relatively longlived descendants of radon and its short-lived daughters, i.e., 210 Pb and 210Po (Archer, et al., 1968), to provide a measure of cumulative past exposure wherein the body acts as an integrating dosimeter. Early studies considered excretion rates of 210Pb and 210Po in urine, blood and hair (Sultzer and Hursh, 1954; Black, et al., 1968; Jaworowski, 1965; Bell and Gilliland, 1964) as well as their concentrations in bone samples, if and when they became available (Blanchard, Archer, and Saccomanno, 1969). These methods were ultimately complemented by in vivo, whole-body counting techniques using low background, NaI-Csl(T1) detectors (Eisenbud, et al., 1969). By this latter method, it would be possible to measure the skeletal burden of 210Pb directly, thereby avoiding the many difficulties associated with the relation between nuclide excretion rates and body burden. The rationale was simple; by knowing the skeletal burden of 210Pb it should be possible, by the judicious use of an applicable metabolic model, to estimate the cumulative lung exposure to alpha-emitting radon daughters (Fig. 1). Various models that were consequently constructed, however (Fisher, 1969), all suffered from the same limitation, i.e., the assumption that the source of 210 Pb in the skeleton and the source of lung exposure to the short-lived radon daughters were simply related and, if not, were at [ ] least not too variable (Raabe, 1970). By now, the difficulty with this assumption has been recognized and more sophisticated modeling techniques have been attempted which presumably present a more realistic picture of exposure conditions (Holtzman and Rundo, 1981). There is, nevertheless, the pessimistic view that due to the variety and variability (in time as well as in character) of sources that may exist for the origin of 210Pb in bone, it may [never] be possible to estimate past lung exposures accurately by an indirect, predictive model. For example, the origin of 210 Pb in the skeleton may include such sources as: 1) the decay of short-lived 222Rn daughters, inhaled and ingested; 2) the decay of 222Rn dissolved in body fluids and tissues; 3) directly from 210 Pb present in air, inhaled and ingested; and 4) 210Pb from non-occupational sources, e.g., food, water, smoking and endogenous 226Ra. The contribution of each of these sources may vary depending upon specific site conditions such as ventilation and mining operation. On the other hand, empirical evidence seems to indicate a trend reflecting the simplest of direct

Jan 1, 1981

By M. A. Schimmelpfennig, A. D. S. Gillies

M.J. McPherson Having worked on the thermodynamics of air/liquid-water mixtures passing through the surface fans of deep mines, I find this paper of great interest and congratulate the authors on producing it. There are two matters, however, deserving discussion. First, the authors have described the classical theory of fog formation with fogging occurring at "supersaturation." In fact, the process of fog formation begins well below 100% humidity. The more strongly hygroscopic nuclei in the atmosphere will attract water molecules and begin to grow at a relative humidity perhaps as low as 70%. The process is a dynamic one with both condensation and evaporation taking place throughout the mixture on microscopic liquid surfaces. As saturation is approached, the rate of condensation accelerates rapidly producing the familiar reduction in visibility. Hygroscopic nuclei are present in all natural atmospheres and under the appropriate conditions of pressure and temperature, will produce clean fogs. However, if the air is polluted by particulates from combustion or other processes then the resultant coagulation with growing liquid particles may produce dense (and sometimes photochemical) smogs. It is this process that is likely to occur in underground mines when moist air is cooled below dew point. Second, the authors have summarized very well the individual measures that might alleviate the problem. In particular, I agree that neither heating nor refrigerating the air, by themselves, provides a satisfactory solution. However, there is a combination of these that provides a neat and effective control of fog formation. This involves a small, self-contained refrigeration unit within a duct but without the usual external heat rejection facility. The air is cooled below dew point and, hence, dehumidified on passing over the cold evaporator coils. The heat from the condenser is rejected back into the air downstream from the water eliminator, as shown in Fig. 1. The duct configuration can be designed to create good mixing at the outlet. I have used a climatic simulation program to illustrate the effect, assuming a 500-m (1,640 ft) long airway of cross section 60 m2 (645 sq ft), an airflow of 9 m3/s (318 cu ft per sec), inlet conditions of 19/19.25°C (66/67°F) wet bulb/dry bulb temperatures, a virgin rock temperature of 17°C (63°F) and typical rock thermal properties for a hard-rock mine. I have also assumed that 10% of the rock surface is wet. Figure 2 shows the variation in temperatures along the airway if no measures are taken. The relative humidity remains close to 100% and condensation will occur throughout the length of the airway. Before any such installation is designed, the exercise must, of course, be repeated for each location with accurate data. However, this example demonstrates the potential of the system. The idea is not new - the principle is sometimes used in air-conditioning plants for buildings. Figure 3 shows the effect of removing 30 kw of heat by evaporator coils sited 40 m (131 ft) along the airway and rejecting that heat (plus another 10 kw of compressor and fan power) into the air at 60 m (197 ft). Condensate water is produced, at a rate of 0.45 L/min (0.12 gpm). The result of this sequential cooling/dehumidification/heating process is to separate the wet and dry bulb temperatures along the length of the airway. The relative humidity increases from 80% at the duct outlet to 92% at 500 m (1,640 ft). The airway is maintained free from fog.

Jan 11, 1983

By Kenneth A. Rogers, Richard F. Hill

Introduction A number of processes for deriving more convenient liquid and gaseous fuels from coal are commercially available or in final stages of development. Generally, synfuels from coal processes have efficiencies ranging from 50 to 70%. Considerable engineering design and development work are necessary to bring forth commercial plants using the various technologies-but technological breakthroughs are not expected or needed. Gasification While a variety of solids handling, gas contacting, and gas quality upgrading techniques may be employed in the various gasification processes, the primary goal is the same-to convert a sulfur-containing solid to an essentially sulfur-free gaseous product. The gaseous product may be a mixture of hydrogen and carbon monoxide with nitrogen. Definitions are not rigorous, but high-Btu gas is generally over 900 Btu/scf(33 534 kJ/m3) and low-Btu gas is generally below 350 Btu/scf(13 041 kJ/m3). Medium or intermediate gas falls between these values. High-Btu production is more difficult, as it requires additional upgrading of a low- or intermediate-Btu gas stream to produce a commercially acceptable product. The carbon/ hydrogen ratio is adjusted either by rejecting a portion of the carbon, increasing the hydrogen, or a combination of both. The chemical processing steps include production processing gas containing carbon oxides and hydrogen by the reaction of carbon and steam (gasification); reaction of hydrogen and coal to form methane (a hydrogasification process); reaction of hydrogen and carbon monoxide to produce methane (methanation); and the removal of impurities. The gasification processes share a number of common techniques. The coal received at the plant site must be further cleaned and crushed or ground before it can enter the gasifier. Conventional cleaning methods are used to remove extraneous materials such as metal, rocks, etc. For some processes the coal must be finely ground so it may be fluidized or entrained in a flowing gas stream. For other processes crushing and sizing only are required. Agglomerating coals may be pretreated by heating, mild oxidation with air, or other procedures to assure smooth gasifier operation and to avoid reactor plugging. Nonagglomerating coals Such as lignite and subbituminous coal normally do not require pretreatment. Feeding a solid material such as coal to a higher pressure reactor is a difficult task. Dry feeders using a series of pressurized lock hoppers, or wet systems in which a slurry is pumped into the reactor, are used. The gasification step is the heart of the process. Here, the solid feed material is contacted with synthesis gas (carbon monoxide and hydrogen). The coal is devolatilized and a portion of the fixed carbon converted to methane. The gas-solids contacting methods used include fixed beds, fluidized beds, moving beds, entrained beds, and free-fall systems. The gasification process, overall, is endothermic and the heat required to maintain reaction rates is usually supplied by burning a portion of the coal feed. External heat sources such as electric resistance heating, molten salt or solid heat carriers, and the introduction of a hot hydrogen stream also have been tested. Following the gasification step the particulate materials and heavy hydrocarbons contained in the reactor effluent are removed by a water quench and solids separation system. If low-Btu gas or synthesis gas is the desired product, the raw gas is scrubbed to remove carbon dioxide and sulfur compounds and then is used directly. However, if high-Btu gas is desired, methanation is necessary. In most gasification processes, the hydrogen content of the gasifier

Jan 2, 1980

By Nicholas S. Lynn

Introduction Borne out of the need for reductions in capital expenditure and increased production, several new and innovative carbon systems have been developed for small precious metal heap leach operations throughout the United States. Perhaps the most important aspect of these systems is the carbon column. Though diverse in design, these columns can be categorized into three basic types. The first is known as the gravity flow type or Cortez type. As the name indicates, solution flows via gravity, throughout 4 to 6 columns which are arranged in a normally stepped con- figuration which is conventionally upflow in design. The second type, known as the vertical column, is an arrangement whereby flow is established through pressurization in an upward manner, throughout 4 to 6 columns in a vertically stacked configuration. This arrangement is typically intended for use with small portable heap leach operations and employs a semi-continuous mode thus preventing gravity from occurring. The third type and newest development in carbon columns is an arrangement whereby the solution flows throughout 4 to 6 columns placed in a side by side configuration and pressurized by a single feed pump (Figure 1). A unique aspect to the third type, is that the adsorb and desorb cycles are accomplished in the same column, due to a fixed carbon charge. An in-depth analysis is warranted due to numerous advantages of this arrangement, and is therefore the subject of this paper. Advantages and Variations One advantage to the third type of carbon column is the fact that initial capital expenditures and operating man- power requirements are reduced. Another advantage is that the system can be made fully portable up to a 0.0315 m3/s (500 gpm) capacity. Systems of this nature are operational at several sites. Above this flow rate, the system's portability is one which can be maintained, but disadvantages (i.e. larger diameter carbon column and greater weights) far outweigh the advantages. There are several variations in each of these systems which allow for unique operation. For example, carbon columns made highly portable, can be moved from unitized heap leach operations to central stripping facilities. Although this method has been used in Colorado, transportation of these units has been known to be quite cumbersome. If distances exceed 5 km (3.2 miles) then special front-end loaders are required. This limits heap locations to within 5 km (3.2 miles) of the central processing facility. Another example transports the carbon charge from the heap leach locations to a centralized processing facility; this method is quite effective. For the past 5 years one mine has employed this technique of transporting carbon in 907 kg (1 ton lots), in DOT containers, towed by company pick-ups. This operation uses a vertical column with a 907 kg (1 ton) carbon charge. A third example uses static carbon columns with fixed carbon charges. Carbon Adsorption System The carbon adsorption system (Figure 1) is fed by a single preg solution feed pump. This feed pump pushes the preg solution through all four to six fixed charged carbon columns, which are on line. The sequencing of the carbon columns is achieved using valves. Expansion of the carbon charge is dependent upon the carbon selected. The carbon typically used is a 6 x 12 mesh size, with a nominal flow rate of 0.00135 - 0.00138 m 3/s (22-25 gpm) per square foot of carbon, based on a 40% bed expansion. With 8 x 16 mesh size,

Jan 1, 1987

By Melvin E. Poad

INTRODUCTION The placement of concrete by means of pumping is one of the fastest growing practices in the construction industry and is widely used in mining applications. In¬troduced in the United States in 1933, this method has been adapted to many aspects of the industry, especially where space for equipment is either limited or inaccessi¬ble. Concrete pumping offers many advantages over other methods of placement. Using pumping equipment, the concrete mixture can be transported in a single operation from a central mixing site to numerous forms in many remote locations, eliminating the need for rehandling the mixture and reducing the labor costs to a minimum. Pressurized pumping provides an extra mix¬ing and blending step, resulting in concrete of improved uniformity and greater density. In turn, this produces high compressive strength and increased durability. Various placement defects can be reduced or pre¬vented by pumping. The steady and even flow of the concrete minimizes the form distortion and delays caused by vibration problems that are common to fast dumping of the concrete mixes. Segregation, planes of weakness, bleeding, and surface faults are diminished considerably. Perhaps the greatest advantages of concrete pump¬ing are the distances and volumes that can be handled. Depending upon the equipment used, pumping rates of from 8 to 115 m'j/h (10 to 150 cu yd per hr) can be achieved, with a horizontal range of up to 460 m (1500 ft) and a vertical range of up to 140 m (450 ft). Theoretically, almost any concrete mixture could be pumped. However, consistency is an important consid¬eration for efficient operation. Mixes that are too wet, too dry, too hard, or poorly graded can cause difficulties that increase the costs. Similarly, mixes containing aggregate material that is over the maximum size or that is porous and highly absorptive can also result in diffi¬culties and increased costs. For the best efficiency, the mix formulation must have a well-graded sand and aggregate combination, with enough fines to provide flowability. If additional water is required for pumping, additional cement must be used to meet the design criteria of the structure. Each pump manufacturer can provide recommended mix formulations for the specific equipment furnished. Since the 1950s, many improvements have been made in pumping technology. Originally, only rigid steel pipe of 168 to 245 mm (6.625 to 9.625 in.) diam was used; today, both rigid steel pipe and flexible conduit are available in diameters of from 76 to 203 mm (3.0 to 8.0 in.). Improved pumps have been developed, and the introduction of power-coordinated booms has in¬creased the versatility of concrete pumping. The older and more conventional placement methods can no longer compete with the flexibility, efficiency, and econ¬omy of the pumping method, and continued research and development can only improve the system and expand its use throughout the mining industry. PUMPING EQUIPMENT The three major types of concrete pumping units currently available are the piston pumps, the pneumatic pumps, and the squeeze-type pumps. Table I provides a comparison of capacities, horizontal ranges, and vertical ranges for pumps of all three types. Piston Pumps The simplest of all concrete pumps are the piston¬type pumps; they are available from many manufac¬turers. As shown in Fig. 1, each unit consists of a

Jan 1, 1982

By Jay S. Silhanek, Vernon E. Andrews

[Introduction] Section 122 of the Clean Air Act Amendments of 1977, Public Law 9595, directed the Administrator of the Environmental Protection Agency, to review all relevant information and determine whether emissions of radioactive pollutants into ambient air will cause or contribute to air pollution which may reasonably be anticipated to endanger public health. In August 1979, EPA published a preliminary report on assessments of public health impact resulting from emissions of radionuclides into air from a broad spectrum of major source categories (1). A section of this document presented a theoretical analysis of the radioactive airborne emissions from several non-uranium mines including iron, copper, zinc, clay, limestone, fluorspar, and phosphate. Since 1978 EPA's Las Vegas Laboratory has been gathering field data on actual radionuclide emissions from these mines to support the earlier theoretical analysis. The purpose of this paper is to present the results of those field measurements in comparison with the assumed values for the theoretical analysis. Data were presented in EPA's preliminary report on both gaseous radon-222 and particulate uranium-238 emissions from non-uranium mines. Most of the emissions data were rough estimates based upon the uranium content of the ore. Preliminary data from a few field studies were also used. Although both the theoretical and field studies by EPA were concerned with radon-222 and radioactive particulate emissions, this paper will concentrate only on the radon effluents. Radon from mines seems to have the greatest potential for possible health effects due to radiation. Data on particulate emissions are presented in other technical reports (2-5). [Theoretical Study] The theoretical emission data are presented in Table I. The estimates for the iron, zinc, and clay mines are based upon preliminary measurements taken by the Las Vegas laboratory. The estimates for the other mines were made assuming that 20% of the total radon-222 in the ore was released during the mining process and the radon release rate from the exposed ore surface was a factor of two greater than that resulting from mining. [ ] Dose assessments for radon from these mines were carried out using model facilities located on generic sites (1). The AIRDOS-II computer code (for estimating dispersion of airborne pollutants) with some minor modifications was used to determine working level exposures to a maximally exposed individual and a regional population. A conversion factor for risk/WL-year(O.021 fatal cancers/person-WL-y) was developed primarily from information on uranium miner exposures (6). This computer code and conversion factor were then applied to the assumed emission rate of radon-222 from each type of mine to develop estimates of working levels, lifetime risks and number of fatal cancers. A summary of this data is presented in table II. [ ] The highest estimated number of cancer deaths per year of operation is 0.05 cancer deaths or 1.0 death due to radon during the 24 year life of a phosphorous mine. For comparison, EPA estimates that underground uranium mines would cause .03 cancer deaths per year of operation in a regional population(1). [Field Study] As a followup to the theoretical study, EPA's Las Vegas laboratory began making measurements in 1978 of actual emissions of radon-222 and radioactive particulates from mine vents at several facilities for each of the industries listed in Table I and II. They were intended to verify general information and radon emissions from EPA's theoretical estimates.

Jan 1, 1981

By John A. Haggman

Philippines is a country that is richly endowed in mineral wealth. In 1988, Climax Arimco Mining Corp. (CAMC) geologists found the Dinkidi porphyry gold-copper deposit in Nueva Vizcaya province. It is the most significant mineral discovery in that country in recent times. To date, the company has defined indicated resources of 124 Mt (136 million st) of 1-g/t (0.029-oz/st) gold and 0.4% copper. This includes a high-grade core of 7.9 Mt (8.7 million st) of 6-g/t (0.175-oz/st) gold equivalent. Total contained metal is 124.4 t (4 million oz) of gold and 499 kt (1.1 billion lb) of copper. Dinkidi's discovery resulted from initial geologic reconnaissance and recognition of the intrusive complex that is exposed at surface and anomalous in its topographic expression. This was followed by systematic exploration. This includes extensive gradient array induced polarization (IP), ground magnetics, geochemical sampling and diamond drilling. This later defined a further 16 satellite porphyry targets in the Didipio region. Climax was been granted a Financial and Technical Assistance Agreement contract with the Philippine government. It allows 100% foreign ownership of mining projects. After four years of negotiations, Climax was the first company to have such an application granted. Some 120 applications from numerous international mining companies are waiting for approval following implementation of new Philippine Mining Act of 1995. Exploration history Didipio is located 200 km (125 miles) north of Manila at an elevation of about 700 m (2,300 ft) in the remote Sierra Madre mountains. This region remains mostly unexplored. The property is accessed by 25 km (15 miles) of logging track from the town of Cabarroguis, Quirino. The area experiences an average rainfall of about 3,000 mm (118 in.) a year. Most of it falls during the July-to-November typhoon season. Didipio was first recognized as a gold province in the 1970s when native Ifugao and Ilongot hunters discovered alluvial gold in the region. The region had been prospected over the years by local companies. They were mostly prospecting for alluvial gold. However, in 1988, Climax Mining geologists identified the potential of an obscure razorback ridge protruding from the alluvial valley floor. This ridge, later named Dinkidi by Climax, was the site of several small- scale tunnels. Locals had mined narrow quartz stockwork veining and sluiced soft argillic alteration zones, using irrigation canals and sluice boxes to catch free gold.

Jan 1, 1997

By Hugh E. Cronin, Lok Home

THE PENETRATION RATE BASELINE DILEMMA The penetration rate is the instantaneous advance rate of a TBM in a rock tunnel. Normally expressed in feet per hour. The production rate is the penetration rate multiplied by the number of hours worked and then factored by the actual utilization of the TBM. In a given rock formation, the actual production rate is a result of many factors some of which are within the control of the contractor and some of which are based on the route selected. Factors that are within the contractors control are cutter profile, frequency of cutter changes, thrust, rotation speed, cutter spacing and the efficiency of the operation. Factors that are site (route) specific are compressive strength, fracture orientation, fracture frequency, micro- fracturing, quartz content, Moh’s hardness, Cerchar Abrasivity Brazilian Tensile Strength and Youngs Modulus of the rock. In addition the following route speci?c conditions are beyond the contractors control; rockjointing, rock stress fault zones, water in?ow and rock decomposition; all of which effect production rate. Any one of the above defined rock properties, equipment specifications and actual operating usage will change the penetration rate. Furthermore, since the rock formation changes both in content and orientation as the tunnel advances, the penetration rate is constantly varying. The current industry practice in bidding tunnels is for each contractor to individually evaluate the rock hardness and other properties and from this information develop a penetration rate. All other factors being equal, the contractor using the most optimistic penetration rate will be the low bidder and be awarded the project. As this view is by definition optimistic, invariably the rock will be harder than the low bid assessment and the contractor will request additional compensation for the changed condition. The contractor will attempt to justify his optimistic assessment as reasonable by using expert supporting analysis. The above described example which is quite common at present in the industry tends to make the most optimistic contractor (at time of bidding) the contractor selected for the project whereas it is in the owners interest to contract with the most efficient contractor not the most optimistic. This situation is similar to the Geotechnical analysis that was prevalent in the industry over twenty years ago. Many projects have experienced a significant reduction of penetration rate from that which was originally estimated. In these cases the contractor often makes a claim for extra compensation based on the difference between the actual rock encountered

Jan 1, 2003

By A. T. Iannacchione

Recent fatal injuries occurring during pillar retreat coal mining call for better identification of the hazards and recognition of risks. Ground control hazards associated with room-and-pillar retreat mining tend to intensify with depth, requiring extra precautions in the form of additional controls. In many locations these activities are further complicated by local complexities often associated with unique or novel circumstances, such as over-mining or under-mining. One technique recently studied by NIOSH, Major Hazard Risk Assessment (MHRA), may help mine operators to mitigate the risks associated with pillar recovery operations. The approach was trialed at two underground coal mines in southern West Virginia that are currently practicing pillar recovery. The first step in the MHRA process involved reviewing the segments or parts of the pillar extraction mining system and identifying associated hazards and threats to the operation. Some of the high risk hazards at these two sites included: ? Rock fall during pillar extraction covers equipment and injury occurs during recovery operations, ? Rock fall above the roof bolt horizon, potentially injuring ? workers and/or requiring recovery action, ? Rib fall under deep cover, potentially injuring workers, and; ? Strata instabilities associated with subsidence of the interburden due to simultaneously mining two seams in close vertical proximity to one another. The mines? risk assessment teams then considered each threat individually in order to systematically identify potential unwanted events. The top unwanted events were examined individually using structured risk analysis tools. The output from the process includes a list of priority existing controls for monitoring and auditing, and a second list of potential new controls. These controls consisted of: Examples of best practices, ? Enhanced communication, ? Implementing standard operating procedures (SOP), ? Protocols for emergency response actions, ? Effective layouts, ? Efficient monitoring, and; ? Successful audits. This paper documents the process as it unfolded at the two mines, and analyzes the strengths and weaknesses of the MHRA technique as it applies to pillar recovery operations. This work was part of a larger NIOSH research project. NIOSH was responsible for: 1) facilitating the risk assessment process known as Major Hazard Risk Assessment (MHRA), 2) documenting the risk assessment process, and 3) providing mine management with a written draft summary of the risk assessment process. The results of the risk assessment represent the thoughts and opinions of the individual risk assessment teams and should in no way be construed as an endorsement of the risk assessment output by NIOSH or the University of Pittsburgh.

Jan 1, 2009

By Stephen H. Partney

Waste clay ponds are a necessary part of phosphate rock beneficiation. They are large, averaging 2.6 km2 (1 sq mile). They are unsightly in that they protrude 6 to 15 m (20 to 50 ft) above natural grade. Stabilization and reclamation is slow and they have had a history of catastrophic failure. Florida has never published a specific rule regarding the configuration or height of these ponds. But it has enforced several policies along these lines. The phosphate industry has been forced to make major monetary decisions that affect mine economics for decades. The Florida Bureau of Mine Reclamation believes that the direction of regulation has been solidified but changes are still anticipated. Phosphate rock has been mined in Florida since 1890 (Fig. 1). Three notable technological changes occurred in the industry that led to major shifts in mining technique and volume. By about 1915, hydraulic mining had been replaced by centralized washers. Hydraulic mines usually started at an outcrop in or adjacent to a stream of the pebble zone. Water was pumped out of the stream through high-pressure monitors and sand and clay were washed away from the pebble. Mobile grizzlies and screens were used in conjunction with animal and human labor to concentrate the pebble and haul it away. Populations were sparse and the clays washed into the stream were considered an acceptable price for the commerce. The clays were not voluminous because the pebble zone typically contained relatively small amounts of them. Machines largely replaced animals by 1910 and provided greater efficiency of production. Centralized washers replaced mobile trommels. They allowed greater ease of access to shipping routes by rail. Some clays were placed in mine cuts from 1915 to 1930. Some were dammed off to increase the capacity of a given site. Some of these also failed, leading to clay plumes that were visible all the way to the Gulf of Mexico. By concentrating the waste clays (slimes) in impoundments, the solids concentration had increased, making plumes persistent for long distances. There were complaints. But there was no litigation against the companies during that time. In 1930, flotation technology allowed the recovery of the phosphate from deeper zones. This was because the "concentrate" size phosphate rock was in the sand-size range and could not be screened out. Centralized beneficiation plants grew into a three-step process - washing and screening, feed preparation and flotation (Fig. 2). Reagent storage, safety and the flotation cell complex made the plants into large capital installations. Larger draglines were required to dig deeper into the matrix. These had dramatically larger production capacities, which were then figured into the overall material balance for a given plant. The number of operators shrank and the production per operator grew. Larger areas were being bermed off for waste clay storage. An economic incentive became apparent for storing as much waste clay as possible in each settling area. At the same time, the population was steadily growing and more eyes were watching the activities of the phosphate mines. Phosphate mining, focused on production and profit, was earning a bad name from its neighbors. When the subject of phosphate mining

Jan 1, 1998

By David B. Campbell

INTRODUCTION This submission was made to the Royal Commission of Inquiry into uranium mining in British Columbia. It discusses the stability of waste rock piles that might be developed in conjunction with uranium mining and the control of leachates that might be generated within these waste rock piles over the short and the long term. Short term refers to the interval during which a waste rock pile undergoes either continuous, or alternatively intermittent development, and in general can be considered to extend over the operating life of the mine. Long term refers to the postmining period, i.e. after the ore-body has been exhausted, and mining operations have ceased. Two major classes of waste material are generated in the course of mining and milling operations. Tails, which are the solid waste materials produced by the milling operations commonly exit the mill in slurry form and are stored in tailing retention ponds. Management and control of these slurried wastes are the subject of other papers to the Commission and this conference. In the course of the mining operations, it may be necessary to remove rock materials that are below cut-off grade. That is, ore concentrations within some of the mined rock may be lower than the concentrations which on the basis of economic considerations justifies milling the material. Rock which is removed in the course of the mining operations, but which is below cut-off grade is referred to as waste rock. This waste rock is commonly consigned to a specific area for disposal where it is placed in a mound or pile, i.e. a waste rock pile. Ore concentrations within the waste rock may vary from zero to just below cut-off grade. Since an increase in the market value of uranium could at some time in future result in reduction of the cut-off grade, it follows that waste rock containing ore concentrations slightly below today's cut-off grade could become ore grade rock at some time in future. For this reason, the mine operators may deem it advisable to separate waste rock according to grade, and to consign the waste rock to two or more individual waste rock piles. For purposes of clarity and simplicity, this submission treats the stability of waste rock piles and leachate control in a manner which assumes that these potential problems are isolated and separate from other aspects of the mining and milling operations. For many site specific cases, the problem of potential leachate control might be integrated with the tailings management aspect of the project, thereby realizing economic benefits while at the same time reducing the potential for adverse environmental impact.

Jan 1, 1980

By Stephen W. Lambert

One of the primary interests of the United States Department of Energy's Mine Planning Division is to fully develop avenues of technical research which potentially offer positive effects on coal mine productivity. One such area of research involves the removal of methane gas from unmined portions of coalbeds through vertical wells drilled from surface locations. As coalbed methane content is reduced, less gas is available for flow into the mine, and consequently ventilation requirements are decreased and/or coal extraction rates increase. Another attractive aspect of the vertical borehole drainage method is that it presents an opportunity to recover and utilize significant quantities of methane gas, which would otherwise be wasted to the atmosphere. The viability of removing gas from the Mary Lee coalbed using stimulated vertical boreholes was first suggested by Elder and Deul as a result of a United States Bureau of Mines' drilling project conducted from 1971 to 1974 (4). Other United States Bureau of Mines' studies forecasted that degasification would eventually be necessary in the Mary Lee coalbed because most new or expanding mine development would take place at depths exceeding 1 000 feet (305 meters), where the methane problem would be severe (3) (13). In 1975 a large-scaled drilling program was designed in order to supply industry's anticipated need for a degasification technology in the Warrior coal basin, Alabama. The results of this government/industry sponsored effort were to be specifically applicable to the Mary Lee coalbed, the most extensive and economically important deep minable coal present in the area. Major technical objectives of this program are twofold: (1) to measure the effects of various well completion designs, particularly hydraulic stimulation, on mining and (2) to determine the effects of well spacing on gas drainage rates. A cooperative agreement was established with United States Steel Corporation in late 1975 and field work began shortly thereafter in the proximity of a newly developing mine near Oak Grove, Alabama. Government responsibility for this program was transferred from the United States Bureau of Mines to the United States Department of Energy in October 1977. To date, as a result of this program, twenty-one wells have been completed into the Mary Lee coalbed at the Oak Grove site. Seventeen of these wells were drilled on an experimental grid pattern located two miles from the active mine. These grid wells are primarily being used to generate data necessary to determine the effects of well spacing on gas drainage rates and will also provide a large amount of information regarding the long-term effects of degasification on mining. The four remaining wells (designated Ton through TW4) were placed near the mine so that the full effects of completion could be studied within the short time required for underground interception. Results gathered from the first two test wells (TW1 and TW2) have been reported in detail (10) and indicated that several improvements were necessary to increase gas drainage rates. Hydraulic stimulation was one of the most important aspects of well design that required improvement. Nitrogen-charged foam stimulation treatment was used at TW3 and TW4 instead of the gelled-fluid type stimulation used at the first two near-mine test wells.

Jan 1, 1980

By Shan Mafi

he Broken Aro coal mine is located at the Woodbury Wildlife Preserve 11 km (7 miles) west of Coshocton, OH on State Route 541. Underground min¬ing at the 16-hm2 (40-acre) site took place during the 1910s. During the past five years, surface mining has occurred along the western and northern perimeters of the underground region. The Ohio Department of Natural Resources (ODNR), R&F Coal and American Electric Power (AEP) are involved in a project to remine the abandoned underground complex. The program also includes installing a mine seal made of fixated flue gas desulfurization (FGD) material. Previous mining activity in this area has resulted in an acid mine drainage (AMD) problem on portions of the reserve. In particular, a prominent AMD source is present in the Simmons Run drainage. The project goal is to eliminate or reduce the AMD that is discharging into the watershed. It was initially hoped that the Simmons Run drainage area could be economically mined. Accordingly, this area was included in the mine permit. However, experience with other previously mined areas on this reserve showed that the old mine workings were more extensive than originally thought. Old mine workings present several problems. The most significant are reduced coal recovery, poor coal quality and AMD liability. All of these problems increase mining costs. And the more extensive the old workings, the more significant the increase in cost. Based on R&F's experience with old mine workings in this area, it was decided that economic recovery of the Simmons Run drainage reserve was not possible. As a result, R&F excluded the Simmons Run drainage area from its early mine plans. Some time after it was decided not to affect the Simmons Run drainage area, R&F and ODNR's Division of Mining and Reclamation discussed the possibility of removing this area from the permit and attempting to correct the AMD problem as an Abandoned Mine Lands (AML) project. Specifically, the discussion centered around mining through a portion of the old mine workings to expose the mine openings in the highwall. Once exposed, the mine openings would be sealed using FGD material from the nearby Conesville power plant operated by AEP. In addition, there was interest in reclaiming the old tipple and associated gob pile located adjacent to Coshocton County Road 17 on the opposite side of Simmons Run. R&F attempted to eliminate the AMD problem by sealing the mine openings with FGD material. Once the seals were installed, they were covered with overburden. Monitoring wells were installed to determine the effectiveness of the seal and the inundation progress in the old mine workings as well as monitoring the quality of ground water. The project was jointly funded by revenue from the sale of the coal recovered during the project and AML funds. The FGD seal is expected to cause well water levels to increase above preseal elevations. However, the additional head pressure due to increased water depths in the underground mine may cause seepage through the bottom of the mine or out through the perimeter. The in¬creased water depth in the underground mine is expected to cause lower oxygen concentrations in the underground mine water. Since acidity is produced by oxidation of iron pyrites, less oxygen should result in better quality water. Monitoring wells will be installed before seal installation so that pre- and postseal water levels and well water quality can be determined. Surface sampling locations will be identified. These will be monitored before and after seal placement.

Jan 1, 1998

By Jozef S. Stachulak

INTRODUCTION Conveyor belt fires represent a serious hazard in underground mines. This fact is well understood in most mining countries. The statistical data for Ontario mines (1) indicates that the majority of the conveyor fires occurred at the head pulley of the conveyor belt. The main emphasis for fire prevention and detection should then be concentrated at the drive pulley of the conveyor designed to transport non-combustible material. In the case of conveyor belt fires, it is of utmost importance to detect the hazard at an early stage, when the overheating has not yet reached the ignition point. Thermal noise detection sensors were installed in 1987 at several conveyor sites at Inco mines. PRODUCTS OF COMBUSTION THERMAL DEGRADATION OF CONVEYOR BELT Various investigations on conveyor belt fire hazards have been made in the past (2, 3, 4, 5, 6, 7). Several belt samples (6, 7) were subjected to thermal oxidative degradation. The belts used in these tests were neoprene, polyvinyl chloride and styrene-butadiene rubber (6). About 70 different compounds were identified in the volatile thermooxidative products. As expected, hydrogen chloride was the major toxic product formed, accompanied by relatively low quantities of other toxic compounds such as carbon dioxide, carbon monoxide, sulfur dioxide, carbon disulfide, hydrogen sulfide, benzene, chloroprene, cresols, chloroethanol, formic acid and C8 hydrocarbons. The research investigation (8) performed by the USBM indicated that "smoldering combustibles generate a very low level of CO compared to the level of smoke produced". The cited publication (8), states that, "During smoldering combustion, typical mine combustibles produce about 2.5 times more smoke than CO. As fires develop to their flaming stages, the trend reverses and about eight times as much CO is produced as smoke." The reader is referred to several significant sources of additional information pertaining to emission products that can be found in references (8), (9), and (10). ANALYSIS OF FIRE HAZARDS U.S.A. AND ENGLAND Nearly 15 percent of all underground coal mine fires in the United States involved ignition of conveyor belts (7). In many cases, the fires propagated through thousands of feet of belt entry and created losses in the millions of dollars. Some of these fires consisted of rubber belts. Some involved polyvinyl chloride and neoprene belts that were classified "fire resistant". Typically, a belt fire begins after the conveyor is stopped. The fire is initiated by burning coal dust and grease accumulation around defective rollers or belt drives that have become heated by friction (7). An analysis of 113 conveyor fires (11) showed that 41 originated at the driving pulleys, 32 at the defective rollers, and 40 elsewhere on the conveyor system. The severity of the fire, which can spread along a conveyor road, has been emphasized by the disaster at Creswell Colliery, Derbyshire, on September 26, 1950, when 80 men were overcome and killed by toxic fumes from the fire (12). The fire started from smoldering caused by friction, and developed into a flaming combustion, propagating along the roadway containing the rubber belt at an estimated speed of 40.2 m/s (90 mph), and travelling a total of 650 m (2100 ft) THE INFLAMMATION OF CONVEYOR BELTS THE MECHANISM OF IGNITION Defective operation of a conveyor belt may start a fire in several ways: - Friction of the belt on the drive pulley. - Jamming of a guide roller, and others.

Jan 1, 1991

By D. H. Steve Zou, Cui Lin

"This paper first discusses the basic attributes of sustainable mining and the responsibilities of various steak holders including mining companies, governments, and engineers. It is followed by a brief overview of the current practice on regulations, inspections, waste management and mine closure planning in Canadian mining industry. A case study is then presented as an example of sustainable mining where mine planning, mineral recovery, environment protection, reclamation and community development were integral parts of the overall strategy. A comparison of the mine site before and after mining is made to demonstrate the ""best practice"" in modern mining.Sustainability in Mineral Resource Development Extraction of mineral resources and other natural resources on the Earth has been and will continue to be an essential activity necessary to support human’s life. We live on the planet and depend on the available resources to survive. The extracted materials form the base to support modern life. However, we must be aware of the fact that mineral resources are limited on the Earth and may not last forever. Every time we extract one ton of materials, there is one ton less. They are not able to regenerate or regrow. One can ask a simple question: How long will they last? Or, is there anything left for our great grandchildren and many generations to come? The answer is not simple. Some minerals have become scarce or about to deplete. Some minerals may last longer. The reserve of a type of minerals depends on what we have discovered and the minable amount depends on accessibility and technology we have. Even if there are minerals in the deep ground, we may be limited by our technological capability. At the same time, we also need to understand the action of mineral extraction from the ground and the consequences of that action. Mineral extraction is a very hard work. We must break the ground to extract the ore, either through surface mining or underground mining. This action means disturbance of the land where we live. The disturbance is much more visible in surface mining than underground mining. The disturbed land, if not properly reclaimed after mining, is not going to be reusable. The very purpose of extracting minerals from the ground is to support our life but the action has a negative impact on our life. How can we reduce and limit disturbance of land from the action of minerals extraction? How can we make the disturbed land reusable? These issues must be properly addressed and a balance achieved."

Jan 1, 2017