Search Documents

Introduction The frigid regions of Canada's high arctic islands are well-known for major oil and gas explorations. But mining leads the way in development. Cominco Ltd.'s Polaris mine is in its second full year of commercial production, and outstripping the rated production capacity foreseen by its planners. The Polaris mine is located on the shore of Little Cornwallis Island, near the settlement of Resolute Bay. The mine property is compact. It occupies about 3 km2 (0.5 sq miles) of the vast Arctic landscape. A number of mining and technological firsts were necessary to bring a mine into production at this 76° North latitude. Development constraints that had to be overcome included climate, remote location, and the limited ice-free shipping season. Construction of the entire process plant and ancillary facilities took place on a barge in the South where labor and supplies are plentiful. The plant was towed through ice-strewn waters to its permanent location at the mine site 1450 km (900 miles) from the North Pole. Freighters moved the first shipments to the South during ice break-up in late summer 1982. Most of the zinc concentrate is sold to European smelters. The remainder is tolled at a custom smelter in Europe, and the resulting metal is sold by Cominco. Lead concentrate is sold to European smelters. The mine was designed to produce 177 kt/a (195,000 stpy) of zinc concentrate and 41 kt/a (45,000 stpy) of lead concentrate. Actual production in 1983 was considerably greater, with both mill throughput and feed grades being higher than forecast. Production was 217 kt (239,300 st) of zinc concentrate and 51 kt (56,300 st) of lead concentrate. Average milling rate was 2.3 kt/d (2500 stpd), well above the designed capacity of 2.1 kt/d of (2300 stpd). Arctic Climate Extremes The climate is typical of the Arctic: very dry with short, cool summers and long, cold winters. From November through February, there is continuous darkness. Continuous daylight prevails from April to August. Precipitation is light, rivaling the Sahara desert at about 127 mm (5 in.) of rain and snow a year. An almost continual wind forms deep snow drifts against any obstacle on the ground. Temperatures range from a winter low of about -50°C (-58°F) to a relatively pleasant 15°C (59°F) during sunny days in August. Freeze-up begins in September and ice thickness increases from less than 0.3 m (1 ft) in early October to a maximum of about 2.1 m (7 ft) in May. The permanently frozen ground extends to a depth of about 427 m (1400 ft). Only a few inches of surface ground thaws in the summer. Exploration Activity Zinc-lead mineralization was

Jan 10, 1984

By S. Frimpong

The coal mining industry is an important sector of Canada?s economy. The cost of mining and haulage of coal in Western Canada is a major focal point when compared to inexpensive coal from Australia. Spot coal price volatility affect contractual price arrangements and this creates pressure on companies? profit margins and their competitive edge. In order to alleviate this pressure, companies may have to take short-term drastic measures that may hurt their strategic positions in the long-term. Companies must also create a mix of their products to ensure effective maintenance of profit margins given various quantity and quality constraints. In this paper the authors provide extensive analysis based on detailed probabilistic production systems for coal extraction and haulage in Western Canada. An optimization model is formulated for typical coal mining operations, processing and haulage from mine sites to the Vancouver Ports using linear programming algorithm. A stochastic model is also formulated to analyze the associated risks and uncertainties. These models are validated using data from five operating mines in Western Canada with varying quantity and quality products and uncertainties. The results show that the five mines studied have to produce between 180,000 and 2.10 million tonnes of metallurgical coal and between 70,000 and 2.16 million tonnes of thermal coal to enhance their profitability given the underlying constraints. The average expected probability of success associated with production capacities from these mines is about 66%. This results in a failure probability of 36%, which is extremely high under contractual arrangements. The results also show that management?s profit expectation of $83 million can be achieved at a zero percent failure probability. With a higher risk of failure of 10%, this expectation increases by 21% to $100.3 million.

Jan 1, 2011

By Dean H. Herrick

The production of crushed stone in the United States has exceeded 1.0 Gtpy since 1987. Eighty percent of the crushed stone produced is used in the aggregate industry, accounting for over half of the quantity of natural aggregate consumed in the United States. Approximately 718 of the crushed stone produced in 1989 was limestone and dolomite followed by granite, traprock, sandstone and quartzite, miscellaneous stone, marble, shell, calcareous marl, volcanic cinder and scoria, and slate in order of descending volume (Table 1). Of the remaining 20% crushed stone produced in the United States and not used as aggregate, 12% is used in the manufacture of cement which is an important construction material. Only 8% of crushed stone is used in specialty products not associated with the construction industry. Therefore, this chapter will concentrate on crushed stone as used in aggregates, with occasional reference to other uses or to chapters which discuss specific nonconstruction uses of crushed stone. Construction aggregates are hard, essentially inert materials suitable for being formed into a stable mass by the addition of cementing or binding materials that produce a concrete by compaction, or by natural weight to produce a road or foundation fill. Aggregates are usually from 80 to 100% of the material volume of the construction masses in which they are used. Conditions necessary for a rock deposit to be developed for construction crushed stone include: Quality-should pass rigid specifications for strength and durability; Quantity-adequate volume of rock is needed to have a production life of at least 10 years, preferably 20 or more years; Market-must have adequate market to support a new crushed stone operation; Transportation-transportation cost must be competitive for the intended market; Environmental-the impacts of mining, processing and transportation of crushed stone on the environment at or surrounding the mine site must be within acceptable limits; Permitability-mining, processing and transportation of crushed stone must usually be permitted by governing agency. The following discussion will touch upon all facets of crushed stone operations from the mineral deposit and its geology to technology, uses, economic factors and end with governmental regulations of mining crushed stone. The sections are not designed to answer all questions, but rather to be an introduction to the crushed stone industry. Where more information is required, The Aggregate Handbook by Barksdale (1991) is recommended as the best general source.

Jan 1, 1994

By David A. Gulley, William A. Vogely

INTRODUCTION The Scope of the Chapter This chapter discusses environmental regulation and closely-related public policies associated with mineral development in the United States. This chapter outlines the nature, extent, and amelioration of secondary effects of mineral development. It sketches the policy foundations of regulation; discusses the implementation of environmental law; describes land use conflicts and land management regimes; and surveys the costs and benefits of environmental regulation. Since regulations are subject to frequent change, the chapter emphasizes basic factual and conceptual material, rather than specific regulations. The goal is to familiarize the reader with the general nature of environmental impacts and mitigation which arise in the minerals industry, and with the issues surrounding the regulation debate. The chapter is organized as a series of sub- chapters. The first of these is a discussion of the conceptual foundations of regulatory policy. The second section summarizes the principal federal environmental statutes, and the implementation of such regulation. Following that, the third section summarizes the current state of knowledge regarding the types of environmental impacts associated with mineral development. This discussion, organized in a format similar to that used in environmental impact statements, can be thought of as a guide to reading and understanding such statements. Next, the fourth section surveys studies of the costs and benefits of environmental regulation. 'These empirical studies are evaluated in terms of the framework developed in the first section of the chapter. In the fifth section, the discussion turns to federal, state, and local approaches to land use control and siting, and the economic analysis of such conflicts. Included are discussions of the two principal forms of public lands mineral entry, the 1872 location patent system and the 1920 leasing approach. CONCEPTUAL FOUNDATIONS OF REGULATORY POLICY David A. Gulley The Role of Regulation in a Market Economy What is Regulation?: Regulation is the intervention of government in the activities of the private market. In a market society, the private sector is presumed to be the most appropriate economic agent. Given this presumption, regulation generally begins with a demonstration of persistent problems under laissez-faire in a given context. Environmental and related regulation occurs because the public believes the free market does not properly value environ- mental quality. In this section, concepts are advanced to aid the reader in understanding the government's role in this respect.

Jan 1, 1985

By John W. Rushton

Maintenance and inventory are usually the last items considered in mine development. They need to be addressed properly and early. The micro-computer brings sophistication within the reach of even the smallest mines. Maintenance and inventory programs, if properly installed, will reduce costs 15 to 25% and allow management time to address the mining and metallurgical problems at start up. Shops and warehouses are rarely designed properly. Large engineering firms spend 5 to 20 times more than is necessary for first class facilities. There is an optimum design, size, and layout. Take the time necessary to assure you get the right people, programs, and facilities in that order. Maintenance, inventory, and inventory control must be addressed early if a small mine is to have a chance at optimizing costs during the first two years of operation. This is hard work and is usually put on the back burner until the mine is in some degree of trouble. Hiring an experienced maintenance superintendent is important but it is not the complete solution. Maintenance systems, design of facilities, and use of computers are not skills that maintenance people usually have. In addition, the work of ordering spare parts and working with erection people is a full time job and any maintenance people on site during construction are quickly recruited. The end result is that few mines start up with an adequate Maintenance or Inventory System in place. The months, and in some cases years, that the mine attempts to operate without a system are both painful and expensive. Designs of successful integrated maintenance and inventory programs are virtually 100% supported with some outside assistance. Our system is the approach that we are most familiar with and this paper will isolate how Rushton International would go about setting up systems and designing support facilities. Micro-computers are the only way for a small mine to go. ~ini-computers cost more originally and operating costs are many times higher than even the most sophisticated micro system. Micro- computer software is developed further and recent advances in hardware makes medium priced units equal to most mini's in RAW COMPUTER POWER. Mines in general, and especially small mines, have no need for main frame power. MAINTENANCE A good maintenance program has: 1. Equipment Master List a. Equipment Detail Reports 2. Work Order and Backlog Control Program 3. Component Control Program 4. Tire Program 5. Wear Materials Program 6. PM Control Program 7. Maintenance History Program 8. Performance Program We also track miscellaneous items such as MSHA training and inspections, timekeeping, etc. Rather than going through the program step-by-step, it makes more sense to go through a typical Maintenance Day and show how the programs are used. The first thing maintenance supervision needs to know is "how we are doing." We

Jan 1, 1987

By Terry Owen

Not since 1917 has a foreign company developed a standalone, grass roots gold mine in Russia. With Russia's political changes of the late 1980s, development of mineral prospects once again beckons foreign investors. Cyprus Amax's interest in Russia began before the mid-1991 breakup of the former Soviet Union. In 1990, Cyprus Amax began searching for such an opportunity. Early this year, production will begin at the Kubaka gold project located in the Russian Far East, near the Arctic Circle. The Kubaka project is a 1.75-kt/d (1,930-stpd) open-pit operation that will produce more than 9.3 t/a (300,000 oz/year) of gold. Identifying Russian mining opportunities In late 1990, the first Cyprus Amax people travelled to Russia. The trip was to determine the potential for western firms to develop profitable mines. This encouraging visit suggested that Cyprus Amax focus on the Russian Far East with its mineral riches and its easier access to the United States. The company's initial efforts thus focused on working with the Soviet Union's Northeast Geologic Expedition, the then government agency for exploration and geology in Russia's Far East. After the breakup of the Soviet Union, Cyprus Amax continued working with the same people, but they now represented new independent, nongovernmental entities. For three years, Cyprus Amax investigated numerous deposits. This resulted in the identification of two properties of significant interest, one of which was Kubaka. Location Kubaka is located in the Northern Evensk District of the Magadan Oblast in the Russian Far East. This is an area east of Siberia. The project is situated in a mountainous area of the Kolyma Range, about 300 km (985 miles) south of the Arctic Circle. It is 285 km (180 miles) north of the fishing village of Evensk and 380 km (235 miles) northeast of the silver-mining town Omsukchan. The site is 950 km (590 miles) northeast of the regional capital city of Magadan. Magadan, the political and economic center of the Oblast, has a population of about 150,000 people. It is served by a year-round deep-water port (with icebreaker assist) and an international airport with service to Moscow and Anchorage, AK. Access to the Magadan region

Jan 1, 1997

By David B. Cook, James R. Bieke

I. INTRODUCTION Lawyers are a cautious breed; and it might be expected that a paper concerning a broad and complex area of legal regulation, prepared by lawyers for presentation to a predominantly non-legal audience, would commence with several caveats. Ours are the following: First, we have written a broad (and, in some instances, simplified) overview of the regulatory system and of some of the more important requirements generally applicable to uranium mine and mill wastes in the United States. Our paper is not a legal opinion setting forth all of the governmental requirements that would have to be met by any particular mine or mill. Similarly, we do not imply that the requirements we mention are necessarily applicable to each and every mine and mill in the country; depending on the facts, some of the requirements may be inapplicable or avoidable through exemption or variance proceedings. Compliance decisions and strategies for particular facilities must be considered on a site-specific basis. Second, we have undertaken merely to describe the regulatory framework and some of the generally "applicable" requirements which have been promulgated and proposed by administrative agencies. We express no opinion on whether, under the U.S. Constitution and statutes, the existing and proposed agency regulations are valid in general or as applied to any particular mining or milling operation. There are, of course, procedures for judicial review of agency action; and newly promulgated environmental regulations have frequently been challenged, with varying degrees of success, before the courts. For us even to begin to consider such issues would expand an already forbiddingly long paper to totally unmanageable proportions. Third, in light of the subject of this Conference we have limited our paper to the legal framework and requirements applicable to uranium mine and mill "wastes" -- primarily mine overburden and waste rock and mill tailings (including waste tailings solution). We treat operating discharges (e.g., emissions from yellowcake drying) only peripherally. Fourth and finally, it is important to note that this paper, at least in so far as it concerns the specific requirements of particular regulations, will likely soon be out of date in some important respects. Despite

Jan 1, 1980

Drainage and erosion control often become problems at mine reclamation projects. An example of this was an abandoned surface uranium mine on the south Texas plains. Engineers with the Texas Railroad Commission solved these and other problems with a three-dimensional geomatrix erosion-control matting at the 69-hm2 (170-acre) site, about 70 km (45 miles) southeast of San Antonio. Enkamat, manufactured by Akzo Nobel Geosynthetics, was installed to reinforce the grass waterways that handle runoff from the reclaimed mine. Reclamation was completed in the spring of 1992. Bill Walker is regional manager for Erosion Control Systems. He worked with the contractor to identify an erosion control product that complied with the project's design and installation parameters. "Use of erosion control matting enabled us to reduce erosion control costs," said Mark Rhodes, with the Texas Railroad Commission. "Also, the erosion control material was more aesthetically compatible with the reclaimed landscape." The commission's design called for a terrace ditch to be constructed midway up the reclaimed spoil slope to catch and collect water. Commission engineers selected spoil slopes, ranging from 5% to 8%, to build reinforced grassed waterways to drain the collected water from the terrace ditches. This was done instead of dropping the water at steeper slope location in rip rap- or concrete-lined channels. Enkamat's three-dimensional geomatrix of heavy nylon monofilaments is 95% open space that aids root growth. Its root-reinforcement system resists the hydraulic lift-and-shear forces created by high-volume discharges of water. In addition, fine eddy turbulences are prevented from isolating and uprooting individual roots and clumps of vegetation. Enkamat is flexible and lightweight. This makes it easy to install. And, because grass grows into it over time, it "disappears" after installation. Between 12,540 and 14,200 m2 (15,000 and 17,000 sq yds) were installed in the waterway using 150-mm (6-in.) staples to fasten the matting, said contractor Dale Blackstock. "It was easy to use; no problem at all to put down." Blackstock selected Enkamat from a list of eight different channel lining materials described as acceptable in the commission's design specifications. The design specifications were based on the results of channel-lining performance tests conducted by the Texas Department of Transportation. Rhodes said that the commission's Abandoned Mine Land Reclamation program had installed Enkamat on other abandoned uranium mines and on an abandoned surface lignite mine near Austin. "Pretty much all of our installations of Enkamat have worked out well," he said. "There have been no failures. The reinforced grass waterways have performed as designed."

Jan 1, 1998

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By R. W. Henn

Introduction Shotcrete, by the American Concrete Institute definition, is mortar or concrete pneumatically projected at high velocity onto a surface. The term gunite is still common in literature. It is a trade name established by Cement Gun Co. of Allentown, PA, around 1911 for a dry mix of fine aggregate material, hydrated at the nozzle, and pneumatically projected at high velocity onto a surface. This article will discuss shotcrete applications, ingredients, mix proportioning, batching and mixing, admixtures, testing, and steel fiber vs. conventional shotcrete. Applications Shotcrete is used primarily by the mining and underground construction industries to temporarily stabilize an excavated rock surface until a permanent cover can be installed. It may also be used as the permanent covering material. Other uses include refractory material, architectural finishes, slope stability, wearing surfaces, repairing existing concrete structures, fireproofing, and corrosion protection of steel. Wet Versus Dry Process In the wet process, all ingredients, including water but not accelerator, are mixed the same way as normal concrete before its placement by pneumatic projection. The accelerator is added in a liquid state through the nozzle at the point of placement. In the dry process, all ingredients, including acceleration in dry form but not water, are mixed just before placement by pneumatic projection. Water is added through the nozzle at the point of placement. Liquid accelerator may be added at the nozzle in the dry process. Ingredients Shotcrete consists basically of the same ingredients as concrete with some limitations. Type I, II, and III cements are used. However, Type II seems to be used most in underground applications. This can be attributed to ground water at most sites having slight to moderate concentrations of sulfates. Air-entraining cement or air-entraining admixtures are generally not used in dry mix shotcrete. It is generally agreed that it is impossible to entrain air due to the absence of the usual concrete mixing action, and the high velocity of impingement of the material on the application surface. Air-entraining cement or air-entraining admixtures are used in wet mix shotcrete. Their use, however, is not widespread due to the placement method and the fact that high velocity air drives off most of the entrained air. Test results are not conclusive in showing any durability increase of shotcrete to freezing and thawing by using entrained air. In spite of current practice, the trend is toward additional research, with more agencies and owners requiring the use of entrained air. The philosophy behind this is that some entrained air is better than no entrained air to increase durability to freezing and thawing. The aggregates used in shotcrete are the same as those used in concrete. However, the largest coarse aggregate presently used is 19 mm (0.75 in.). A typical gradation requirement is shown in Table 1. The water quality requirement for shotcrete is the same as that for concrete. Accelerators are by far the most important admixture in shotcrete.

Jan 6, 1984

By Tim Neil, O&apos

Introduction On the banks of the Columbia River, about halfway between Seattle and Spokane, sits Wenatchee, WA. It calls itself "the apple capital of the world." And it has a gold mining history that dates back to the 1880s. It was just outside Wenatchee - three blocks outside, to be exact-that Asamera recently dedicated its $60 million Cannon underground gold mine. At full production, it is estimated the Cannon mine will yield between 5 and 5.6 t/a (160,000 and 180,000 oz per year) of gold. That would make Cannon the largest North American underground gold mine to be brought into production this year. Cannon should also be among the top 10 of all North American gold producers. Asamera officials project Cannon's operating costs at about $4.8019 ($150 per oz). At that rate, the mine should also be one of the lower cost and most profitable gold mining operations in North America. One reason for low operating costs is low electric power costs. The Cannon operation will be paying about 2.5 cents per kWh for hydroelectric power supplied by the Bonneville Power Authority. Proven and probable ore reserves at Cannon are in excess of 4.7 Mt (5.2 million st). Reserve grades average 7.29 g/t (0.21 oz per st) of gold in three ore zones, in order of discovery - B, B West, and B North. The ore bodies could have been mined by open-pit methods. But underground mining was chosen for environmental reasons. In addition, the rich B North ore body extends beneath a nearby horse stable and arena. The Cannon mine area comprises some 20 km2 (5000 acres) in Chelan County. The mine site is located at the 305 m (1000 ft) elevation in Dry Gulch at the base of the Cascade Mountains. The initial estimate of mine life for the Cannon operation is eight years, depending on gold prices. But Asamera officials believe the Wenatchee area has excellent potential for future gold discoveries. Asamera, Inc. of Calgary, Alberta, owns 51% of the Cannon property, through its wholly-owned Asamera Minerals (US). Breakwater Resources Ltd. of Vancouver, British Columbia owns 49% of the operation. The Cannon mine is named in honor of longtime Asamera, Inc. executive and current company director, geologist Donald G. Can¬non. It was he who first brought the Wenatchee property to Asamera's attention and urged the company to pursue it. Asamera is a major explorer and producer of oil and gas. Its Cannon operation is the largest and most significant to date in its mining division, according to Rob¬ert G. Welty. He is Asamera's chairman and chief executive officer. It should be noted there was an element of serendipity involved in Cannon's development. The development program be¬gan when geologist Cannon visited the Wenatchee area. He was visit¬ing old mining districts. He liked what he saw. The Cannon property was eventually optioned for ex¬ploration, including a modest drilling program.

Jan 12, 1985

The response of 174 domestic water supplies to longwall mining of the Pittsburgh coal seam was compared to various physical parameters. Sixty-four percent of domestic water supplies returned to service without the need for intervention, while thirty six percent required intervention to reestablish a suitable water supply. Domestic well response is strongly correlated with the topographic setting. Valley wells showed the least effect while hilltop wells showed the greatest effect. Well response was also found to be correlated to the location of the well above the mining with greater effects observed in zones of surface tension and compression, and fewer effects in zones which are stress neutral. Ground water supplies remained unaffected or were re¬established at 149 of 150 sites, indicating that ground water resources remain available to domestic wells after mining. Results of this study support the stress-relief model of ground water flow in the Northern Appalachian Basin. Longwall mining's effect on this system is to locally increase fracture connectivity in the near surface zone. This may shift the zones of saturated fractures to greater depths beneath hilltops and hillsides, and increase recharge and storage in valleys. General trends in well response are predict¬able utilizing the stress relief conceptual model, the topographic setting of the water sources, and their location over the mine.

Jan 1, 1986

By Naoko Shimazaki, Andre Xavier

Over 10 million tourists have visited Vietnam in 2016. Travel and tourism accounted for 9.3% of the country’s Gross Domestic Product (GDP) in 2014. At the same time, as with many other resource-rich developing countries, Vietnam has been developing its extractive resources sector as a means of promoting the country’s social and economic development. In 2015, mining was the third largest contributor to GDP, and accounted for 8% of Vietnam’s gross domestic product. Vietnam is the third largest mineral producer in SE Asia. Although it produces zinc, nickel, bauxite, and manganese, coal mining is its most developed sector. The country has over two hundred coal mines, and total reserves of approximately 6 billion tons. Quang Nihn Province, where the World Heritage Site Ha Long Bay is located, is a very important tourism destination. It is also a coal-rich region where mining extraction and processing have been active since the early 20th century. Vietnam is signatory of the United Nations Sustainable Development Goals (SDGs). The country is aware of the importance and the challenges involved in managing the extractive sector in a way that does not undermine its tourism industry and yet that contributes to the country’s sustainable development. To this end Vietnam is taking actions towards implementing more advanced coal-mining extraction and processing techniques. The country is furthermore promoting a responsible mining sector, and is investing in programs that foster environmental protection and sustainable tourism. This paper examines the case of the Ha Long Bay region and the project involved in relocating the Hong Gai coal preparatory factory from a seafront area to a mountainside area. This paper provides a preliminary review of the initiatives adopted by the government of Vietnam to address the existing challenges that have resulted from a focus on promoting the country’s socio-economic development through the exploration of its rich coal endowment. Furthermore, it also describes Vietnam’s legal and policy frameworks. In conclusion this study identified that Vietnam has drafted a National Action Plan to implement the Sustainable Development Goals. The country is also taking an integrated approach to implementing the SDGs agenda and that it is assigning responsibility to a variety of ministries to achieve SDGs’ specific targets. Furthermore the country is changing policies and the legal framework in order to facilitating the execution of the work of agencies that are responsible for implementation, regulation and enforcement. In this respect, the approval of the National Action Plan on Sustainable Development Goals is another important step in that direction. While the decision of supplying its internal market with high quality coal helps minimize negative environmental impacts in Vietnam, exporting low quality coal to other countries does not help resolve the problem of CO2 emissions globally. With respect to the 2030 Agenda, this may be considered a temporary solution since to achieve the SDG goals, Vietnam will have to consider other sources of cleaner energy in order to align with the Sustainable Development Goals # 7 on affordable and clean energy.

Jan 1, 2017

By Sandy Clamage

"Seeing the elephant" was a term often heard from 1849 to 1859, the period of the great California Gold Rush. The phrase was used by those who dreamed of instant wealth that was believed could be found in California's virgin earth and mighty rivers. When news of fabulous gold strikes throughout the Mother Lode reached far away places, thousands of gold seekers left home and family to join in this incredible adventure. The barren, placid state of California soon became one of the most bustling, populous areas in the West. Before the Rush Before 1848, Mexico ruled California. It was then a remote region, isolated from the urbane world of the East by 2900 km (1800 miles) of scorching desert and impassible mountains. By sea, it was 29 000 km (18,000 miles) via Cape Horn. Spaniards and Mexicans settled the coastal lands on tracts donated to them by the Mexican government. The inland area was the domain of Indians and a few settlers who also had been granted estates by the government. Among those settlers was Captain John Sutter. He had been fortunate enough to obtain about 11 leagues of land (spanning 100 km or 60 miles in length) from Governor Alvarado of Mexico. Sutter was somewhat of a visionary and possessed a gifted tongue. He managed to receive most of what he desired with minimal trouble. Enchanted with Sutter's personality, Alvarado promised him Mexican citizenship. Alvarado also commissioned him to become "representative of the government and officer of justice on the Northern frontier." With uncanny foresight, Sutter began building a fortress on his land in the Sacramento Valley. It later became known as Sutter's Fort. It was more than just a fort, however. It also became a stopping place and home for many foreigners and Americans who traveled to California, and it eventually became the mecca for overland pilgrims. Sutter engaged in many projects. These included a cattle ranch, fur trade and trapping, and the construction of an irrigation system. With the influx of immigrants over the years, the community around the fort grew rapidly. Lumber was much in demand and Captain Sutter agreed to supply the necessary capital for a community sawmill. The site chosen was some 72 km (45 miles) northeast of the fort on the south fork of the American River in the town of Coloma. During the course of its construction, Sutter's carpenter, James Marshall, discovered a problem with the tailrace on the mill. First Strike Early in the morning on Jan. 24, 1848, Marshall was checking the tailrace. He noticed an object shining in a foot of water at the bottom of a ditch. He reached down and picked it up. His heart began to thump wildly as he realized he was holding a gold nugget. Sutter planned to keep the find a secret for as long as possible. He knew very well that he could become an extremely wealthy man. The ever loyal Marshall remained faithful to his employer and the pair did their best to obtain more

Jan 3, 1985

By Nelson R. Shaffer

Implementation of the Clean Air Act Amendments of 1990 is negatively affecting production of coal used for generating electric power in Indiana and elsewhere in the Midwest. Required reduction of sulfur compounds from gas streams, or flue gas desulfurization (FGD), as mandated by these laws has encouraged installation of wet limestone scrubbers at many generating plants. Increasingly stringent requirements that will begin in 2000 are expected to necessitate even more extensive use of such scrubbers. Indiana has large deposits of limestone-the major consumable alkaline raw material for scrubbers-that can meet an expected demand of several million tons per year. Limestones are not, however, all the same. Different limestone units behave quite differently when used as scrubbing agents under differing conditions in actual practice. Decisions about FGD scrubber details would be more meaningful if made with thorough knowledge of which rock units contain the most efficient FGD limestones and which sites of suitable stone are located nearest to power plants. Even though abundant carbonate rocks occur in Indiana, their suitability in scrubbing systems has received little attention, and few attempts have been made to match details of stone resources to the needs of various utility scrubbing systems. Optimization of the fit between geologic characteristics of the existing limestones and prospective scrubber systems should allow for greatly improved planning and operation of FGD systems with attendant lower overall costs. Electric utilities have developed computer models to predict FGD system operations (i.e., the FGD-PRISM model of the Electric Power Research Institute). These models require geologic data such as reactivity that are commonly unavailable. We generated data needed for the model during a cooperative effort among the Indiana Department of Commerce, the Indiana Geological Survey (IGS), The Indianapolis Power & Light Company (IP&L), and the Indiana Mineral Aggregates Association. Our goal was to provide missing geologic details of Indiana scrubber-stone raw materials and apply them to the FGD-PRISM model to provide general guidance to determine which geologic units can provide stone for most efficient sulfur removal. Results of the model for selected limestones and parameters specific to one IP&L generating plant were calculated. Geologic data generated may be applied to other generating operations, and our examples should help other utilities optimize their FGD strategies. Several hundred samples from more than 30 active quarries were collected and their physical properties determined. Grindability values ranged from 7.2 to 21.7 for 50 selected samples. Acid-insoluble residues of less than 1% to 13% were found. Dissolution rates as an index of reactivity varied over two orders of magnitude for the selected set of samples. These data plus chemical analyses and Ca/Mg ratios were entered into a generic scrubber model to determine rates of stone use and scrubber efficiency for various stone. Removal of SO2 was projected by this model to range from 89% to 98% with stone utilization rates from 91% to 93%. Excellent scrubber stone sources were found in Mississippian rocks in central and southern Indiana. Rocks of the Ste. Genevieve and Salem Limestones were especially efficient. Even small amounts of dolomite, clay minerals, and quartz diminished a stone's usefulness for FGD scrubbing.

Jan 1, 1999

By J. Allen Hennessy

INTRODUCTION The increasing price of gold and silver over the past 10 years has caused increasing activity in the exploration, evaluation and development of precious metals projects. Many of these deposits are relatively low grade and short lived which makes them economically sensitive to the major project variables such as metal price, capital cost, operating cost and of course, tonnage and grade. These deposits often have a high variability (a coefficient of variation -- o/u -- of 2 to 5) and an intermixing of ore and waste, making ac- curate ore reserve estimation difficult, especially when using traditional estimation techniques. Often, the estimation errors are not the 10-20% that we see in base metal deposits, but the errors in grade and tonnage can be as high as 50%, which can obviously have a very substantial impact on project Recent developments in geostatistics when coupled with a sound geologic under- standing of the deposit can significantly improve reserve estimates of these variable precious metals deposits. Examples will be given of actual deposits where the traditional estimates were significantly different from the mining reality. An attempt will be made to explain the applicable geostatistical tools with a minimum of geostatistical jargon and without complicated formulas. The key to improving the reserve estimates is a clear understanding of the deposit geology and especially the structural controls, the use of local estimation techniques that recognize the intermixing of ore and waste and the effect of selective mining on recoverable reserves, and the use of a global reserve estimation technique to check the results of local estimation. Geologic Controls The vast majority of gold and silver deposits being mined or developed in the western United States would be classified as epithermal deposits. These are formed by hydrothermal fluids (hot water) flowing upward through the rocks and depositing the precious metals as the fluids cool or reach areas of lower pressure or favorable chemical sites. These environments are similar to present day hot springs-type environments with some deposits being clearly associated with surface hot springs such as the Homestake McLaughlin deposit in northern California. These hydrothermal deposits can occur in sedimentary rocks resulting in deposits such as those of the Carlin district or the Jerritt Canyon deposit or the hydrothermal systems can occur in volcanic rocks forming deposits such as Round Mountain, Manhattan or Paradise Peak. The mechanisms of formation were similar in either case with the solution flow controlled by geologic structure and precious metals deposited when the conditions of temperataure, pressure and chemical environment were favorable. The gold and silver hearing solutions travel through permeable faults and fracture systems depositing the metals along these channels. The grades are often highest in the central parts of these conduits (veins) with lower grades in the surrounding rocks. An understanding of the nature, distribution and orientation of these plumbing systems is important to a realistic reserve estimate. The point to be emphasized here is that, good, sound geology in the form of geologic mapping, logging of rotary chip samples and a few carefully logged core holes can signifi- cantly improve an ore reserve estimate.

Jan 1, 1987

By Peter J. Huck, Bruce G. Stegman, Richard E. Thill

Introduction Backfilling of mine voids is used to prevent or control the effects of subsidence on surface structures. The pumped-slurry, blind backfilling process has been successful for stabilizing ground over abandoned and inaccessible underground coal mines. This article describes the systematic evaluation of potential monitoring systems that would improve backfill monitoring technology. It also details field proof-of-concept tests that were conducted on two systems and the difficulties encountered in implementing them. Ground subsidence over abandoned mines can have devastating effects on overlying urban areas decades after the closing of room-and-pillar mines. The result may be cracked foundations, ruptured gas and water lines, broken sewers, distortion or cracking in superstructures, and sinks and potholes in the ground surface. About 32,000 km2 (8 million acres) of land in the US has been undermined for coal. According to the US General Accounting Office, 8,100 km2 (2 million acres) have undergone subsidence and another 8,100 km2 (2 million acres) are expected to subside by the year 2000. Actual figures on land affected or threatened by subsidence are probably much higher, since these estimates were based on late 1960s studies. For more than two decades, the US Bureau of Mines has been engaged in stabilizing ground in urban areas having high risk potential for subsidence costing millions of dollars. Thousands of acres have been stabilized, protecting property worth hundreds of millions of dollars. In earlier years, backfilling was by in-mine stowing in accessible mines or by gravity-feed sluicing methods in inaccessible mines. Pumped-slurry methods have been used extensively in the past 10 years. More slurry can be injected for fill from fewer injection holes over extensive areas in abandoned mines. Since this method requires fewer boreholes, there is less disruption of surface facilities. An investigation was conducted to determine the feasibility of using advanced, remote sensing or monitoring technology for application in monitoring fill placement. Specifically, the objective was to develop conceptual systems for blind backfill monitoring that require fewer boreholes and give better definition than is now possible. Blind Backfilling Methods Blind backfilling operations are conducted from the surface and do not require personnel and equipment underground. These methods are applicable to abandoned, inaccessible workings. Two categories of blind back-filling are point support, practiced by civil engineers to protect individual structures or surface facilities, and areal backfilling methods, used to protect large areas against subsidence. Point Support Methods Point support methods are usually gravity-feed systems. In general, point support methods use small volumes of expensive fill material and require a large number of boreholes within a constructed site. Because of the processed material used for back-filling and the close spacing of the injection boreholes, control and monitoring often may be accomplished by borehole cameras. Areal Backfilling Areal backfilling is conducted mainly by the pumped-slurry injection process (Fig. 1). In eastern and interior coalfields, material used is often mine refuse or flyash, both being undesirable on the surface and costly to dispose of in an environmentally acceptable manner. Hence, the use of

Jan 12, 1983

By Jamal Rostami, Ataollah Rahbar, Jürgen Paulzen

"Uma Oya Multipurpose Development Project is located in South West Sri Lanka. This project, among many components, involves a 14 km headrace tunnel in very hard and abrasive igneous rocks. The tunnel is under construction by a 4.4 m diameter double shield TBM. The headrace tunnel has already reached 5km milestone and has passed through some reaches of tunnel in very strong intact rocks with no joints. Low penetration at high thrust load has caused frequent stoppages for cutter change leading to low utilization and advance rates due to low cutter life. The original machine was dressed with 27, each 432 mm (17 inch) diameter, 19 mm (3/4 inch) tipped disc cutters. However, various cutter diameters of 432-457 mm (17-18 inch) and cutter tip widths 13 to 19 mm (0.5-0.75 in), have been tried to see if cutter life and penetration rates could be increased. This paper will review the history of the project, the geology of the site, along with TBM performance and cutter life. It will focus on frequency of different cutter failures encountered in various ground conditions. Also, results of using variation of cutter diameter and tip width to cope with the hard rock conditions and their results in increasing machine productivity will be discussed. This allows for better understanding of parameters controlling disc wear/life and leads to better cutter management for more efficient operation of hard rock TBMs in similar conditions. INTRODUCTION The Uma Oya Multipurpose Development Project (UOMDP) lies in the south-eastern part of the central highland region of Sri Lanka. The Multi-Purpose Project Of Uma Oya is planned to convey water from Uma Oya to Kirindi Oya Basin for hydroelectric energy generation includes Puhulpola RCC Dam on the Uma Oya river, Dyraaba RCC Dam on the Mahatotilla Oya river, a conveyance tunnel from Uma Oya to Mahatotilla Oya (L=3750m), a long feeder tunnel from Mahatotilla Oya to Kirindi Oya river. The feeder (or power) tunnel Lot consists of a 15554 m long headrace tunnel (HRT), the surge shaft and tank on the upstream of the vertical shaft, a 650 m vertical shaft with steel lining, and an underground powerhouse and a 3650m tailrace tunnel (TRT)."

Jan 1, 2016

By Vladimir Adamek

Due to the variability of subsidence characteristics across the U.S. coalfields, it was concluded that it would be practically impossible to develop a universal predictive model for mining-induced subsidence based on theoretical assumptions. Therefore, an effort was made to find a procedure to develop an empirical subsidence predictive model based on a sufficient Mount of field data from one mining area (in this case the Northern Appalachian Coal Region). It was also thought that this procedure, if successful, could be used as the template for developing predictive capabilities for other coalfields with different subsidence characteristics given a reasonable amount of field data. It has been found, in the Northern Appalachian Coal Region, that the variability of subsidence characteristics can be expressed by a polynomial equation developed through regression analysis of the variable subsidence coefficient and derived directly from the field data. In this study, field data were obtained from 11 Bureau longwall panel studies (16 half profiles) for static subsidence and 14 panels for dynamic subsidence. The effects of lithology, expressed in the form of a variable subsidence coefficient, have been separated for each test site by introducing a correlation between hythetically homogeneous overburden and existing ithological conditions. For each longwall panel, the characteristic of the variable subsidence coefficient was defined along individual static profiles. The definition of mean values with acceptable deviations is the substance of the predictive method. The same procedure was used to develop a predictive model for dynamic subsidence, since it war discovered that the rate of longwall face advance is not a necessary functional parameter. This paper presents the theory, development, and application of the static and dynamic subsidence prediction models.

Jan 1, 1986

By Robert J. Ramsey, N. Finkelstein, Robert D. Jeppson

Introduction The Utah Copper Division of Kennecott Copper Corporation will present its contribution to the A. M. Gaudin Flotation Symposium in four parts. The first two segments will discuss briefly the historical development of the Utah Copper Division and describe the ore body. The third segment will review the facilities and operating procedures for the Utah Copper Division's newest plant, the Bonneville Concentrator. The fourth segment describes flotation process circuitry, including molybdenite recovery procedures, at the Arthur and Magna concentrators. (The Bonneville concentrator is a crushing and grinding unit and does not have its own flotation plant). 1. Historical Development Progress through change has been the key to the successful operation of the Utah Copper Division for more than 70 years. As the original low-grade copper operation, the pressures to remain competitive and profitable have dictated the timing and extent of each change. Much of the change has occurred through technological and economic advancements in the area of ore concentration. The Utah Copper Division of Kennecott Copper Corporation had its origin June 4, 1903, when the Utah Copper Company was organized. The initial mill of 300 tpd (tons per day) capacity was built at Copperton a few miles below the present Bingham Canyon mine site. From 1904 to 1910, the Copperton mill was expanded to a capacity of 1,000 tpd, and all of the known apparatus for gravity concentration were evaluated.

Jan 1, 1976