Search Documents

By J. Kou

The adsorption process, density and structural property of the oleate layer adsorbed onto a hydroxyapatite (HAP) surface at six different concentrations and three pHs (pH 8, 9 and 10) have been studied using the technique of quartz crystal microbalance with dissipation (QCM-D). The present study demonstrated the versatility and accuracy of the QCM-D for surface adsorption characterization. The real-time measurements of frequency and dissipation shifts with a hydroxyapatite-coated sensor revealed changes in the hydroxyapatite surface during the entire adsorption process. Chemisorption and surface precipitation of sodium oleate were also observed on the surface of hydroxyapatite through the use of Fourier Transform infrared spectroscopy(FTIR). Chemisorption dominated at low concentrations and high pH values and formed a rigid and thin adsorption layer. Surface precipitation of calcium oleate and micelles dominated at concentrations higher than critical micelle concentration (CMC) and lower pHs and formed a thick but dissipated adsorption layer with a high hydration level. Three distinct adsorption behaviors were identified from the different slopes of ?D-?f plots. The adsorption density was less than a monolayer at concentrations <0.164 mM, but increased significantly at concentrations higher than 0.821 mM at all three pHs. The critical concentration at pH 8 was 0.33 mM, which was lower than at pH 9 (0.821 mM) and pH 10 (3.3 mM).

Feb 1, 2012

By J. C. Johnson

The problem of estimating pillar capacity in coal mines has motivated development of a variety of empirical equations. Most of these equations have arisen from experience and a very limited set of measurements that have, necessarily, been focused on particular regions or coal fields. Their applicability is often limited to a specific range of pillar sizes. This is of particular concern in the design of large gateroad pillars and small barrier pillars between panels. The result has been a variety of equations and equation coefficients that can calculate load estimates to size pillars. Inclusion of these equations in more sophisticated loading models, such as boundary element methods (e.g. LaModel and MULSIM) has been hampered by absence of a function that describes specific variation of coal strength within the pillar. A singular exception, to our knowledge, is a function corresponding to the Bieniawski pillar strength equation. Because of this, it is the only coal strength criteria inherently available in most boundary element models. This paper presents a general method for deriving local coal strength, as a function of distance from the pillar rib, for an arbitrary pillar strength equation. Integration of this function provides the strength of pillar regions, or cells, needed for boundary element models. The method is demonstrated for the Bieniawski, Maleki and Holland-Gaddy equations. The Maleki and Holland-Gaddy equations contrast strongly with Bieniawski as strengths are extrapolated to large pillars and barriers. This development provides a tool for incorporating any of the proposed empirical equations into a boundary element model, thereby allowing the analyst to choose the most appropriate equation for a particular region, coal seam and/or pillar size.

Feb 23, 2014

By Tim M. Benson, Adam L. Lamanna, Carolina Martinez-Gutierrez, Mark J. Stephani

The Lower Concourse C Extension (LCE) 108-in Storm Sewer consists of a 2,797-foot long, 27 to 55-foot deep, 108-in I.D. storm sewer tunnel. Situated beneath active taxiways and a terminal apron at Hare International Airport (D), the tunnel diverts ows from existing storm sewers located within the footprint of a future satellite concourse. The project was delivered via Construction Manager at Risk (CMAR) as part of Chicago Department of Aviation’s (CDA) ongoing O’Hare 21 Capital Program. This paper presents project details, multiple stakeholder coordination, subsurface risks and challenges, TBM performance, and impacts to existing infrastructure.

Jun 23, 2024

By Shaoyang Yan, Xinming Chen, Huazhe Jiao, Huaibao Chu, Chang Wang

In terms of the technical problems of rib spalling in large mining height coal face, a long-distance advanced pre-grouting layer flexible reinforcement technology is proposed in this paper. Based on the mechanism and failure mode of rib spalling in the coal face, the mechanical properties of the aluminum plastic composite pipe were analyzed by using the tensile and compression experiment. The deformation and strength characteristics of “flexible pipe + grouting” specimens were studied by uniaxial compression test, splitting test, and shear test. The UDEC numerical simulation software was used to simulate the reinforcement effect of “flexible pipe + grouting” at different positions. Combined with the field application, the feasibility of long-distance advanced pre-grouting layer flexible reinforcement technology was verified. The test results show the following: The coal face has the characteristics of brittle and large deformation. The aluminum plastic composite pipe has the characteristics of good elongation and tensile strength, which can endure the large deformation of the coal face. The “flexible pipe + grouting” can improve the tensile and shear strength of coal. The UDEC numerical simulation analysis indicated that the grouting hole layout of “flexible pipe + grouting” has a significant difference in the reinforcement effect of the coal face. Compared with single row grouting reinforcement, the reinforcement effect of double row grouting holes 1.5 m and 3.0 m away from the roof is better. According to the field application, it is feasible to use aluminum plastic composite pipe as a flexible grouting pipe to reinforce coal seam with 80–100 m long-distance pre-grouting. Long-distance advanced pre-grouting layer flexible reinforcement technology can improve the daily production of coal and reduce the support cost of the coal face. As a new method of reinforcement, long-distance layered flexible reinforcement has a significant effect on the prevention and treatment of rib spalling in large mining height coal face.

Sep 27, 2022

By Yuchen Wu, Purushotham Thkkaraja, Marek Borowski, Jie Liu, Jianwei Cheng, WANCHENG ZHENG, Yu Wang, Weidong Lu, Gang Zhao, Zhanyou Sa, Huan Yang, Yuhang Wu, Hui Wang

The abstract discusses the importance of gas drainage in coal mines for safety, environmental protection, and resource utilization. It highlights the significance of borehole sealing technology for efficient gas drainage. The study introduces a new inorganic retarding sealing material and investigates its properties, including stability, thermal stability, fluidity, and thixotropy. The material's diffusion performance in cracks is tested using a self-designed system. Field tests in a coal mine demonstrate the material's effectiveness in improving borehole sealing compared to traditional materials.

May 1, 2022

By NARAYAN K. BHAGAT, ARVIND K. MISHRA, C. Sawmliana, Rakesh Kumar Singh, Panchanan Hembram

Mining operations in close proximity to dwellings and sensitive structures present challenges in terms of mitigating the undesirable effects of blasting while maintaining productivity and ensuring the safety of surrounding communities. This paper explores the application of advanced blasting techniques, including the use of electronic detonators and the splitting of total explosive charges, to address these challenges. A series of experimental blasts were conducted, comparing blasts conducted with and without splitting of holes, to assess the impact on ground vibrations. The results demonstrated significant reductions in vibration magnitudes when implementing controlled blasting practices with splitting techniques. The findings highlight the importance of total explosive charge in determining ground vibration magnitudes within the danger zone of mine workings. The use of electronic detonators provided precise control over blast sequencing, contributing to safer and more efficient mining practices. These advanced blasting methods offer a practical and innovative solution for conducting safe mining operations near dwellings and sensitive structures, ensuring compliance with safety regulations while sustaining productivity.

Jan 23, 2024

By Kwadwo Osseo‑Asare, Isehaq Al‑Nafai

The hydrometallurgical processing of bastnasite is a well-known process that is used to extract rare earth metals. However, more accurate measures are required to enhance the efficiency of extracting and recycling rare earths. In this work, Pourbaix (Eh–pH) diagrams for La-, Nd-, and Pr-(F)-(CO3)-(SO4)-(Cl)-(NO3)-(C2O4)-H2O systems were theoretically derived to investigate the stability relations during the hydrometallurgical processing of bastnasite. The diagrams for RE-H2O systems show similar trends to the original ones drown by Pourbaix. The stability domains of RE carbonates were presented by RE-CO3-H2O systems with pH range of 4.5–11. In contrast, the diagrams for RE fluorides showed a large stability region of insoluble REF3 (pH ~ − 1.7–12). The decomposition behaviors of REFCO3 were studied by constructing Eh–pH diagrams for RE-F-CO3-H2O system. The stability regions of bastnasite species extend from nearly neutral to basic media (pH ~ 6.5–12). The acid treatment (using H2SO4, HCl, and HNO3) of bastnasite was investigated by constructing Eh–pH diagrams for REF- CO3-(SO4)-(Cl)-(NO3)-H2O systems. According to these systems, REFCO3 can be decomposed at pH ~ 6.5 when treated with H2SO4 and at pH ~ 1.7 when treated with HCl and HNO3 acids. On the other hand, the alkaline treatment of REFCO3 converts it to RE(OH)3 at pH ~ 11. The recovery of rare earths ions was studied with the aid of RE-C2O4-H2O systems which shows a wide stability region for RE oxalates in pH range of − 2–11. This theoretical approach explained the aqueous relations in the hydrometallurgical processing of bastnasite ore and it can improve the practical hydrometallurgical processing of such ores.

Feb 9, 2024

By Sara Swiokla Korsikas, Toren Olson, Amado Guzman, Yuri O. Zepeda P

Ore agglomeration has been used as part of the heap leaching process for the last 40 years. However, industrial experience shows that the lack of a universal agglomeration standard has limited the benefits of this, otherwise, valuable unit process. The more complex the ore, in terms of the nature and relative abundance of fines (<74 μm), the more important that the agglomeration product satisfies some minimal requirements. This paper presents an agglomeration scale that identifies the quality standards for agglomerates and documents the resulting mechanical, physical, and hydraulic (hydrodynamic) behavior associated with each level on the agglomeration scale. The hydrodynamic properties of an agglomeration product are critical for the proper design of a leaching operation and, as shown in this paper, can be used to select the optimal pretreatment method for a given ore sample. Agglomeration as a unit process not only allows better conditioning of the hydrodynamic behavior of the ore but also creates an opportunity for optimized delivery of reagents to kick-start the leaching process which may ultimately improve the economic performance of leaching. Industrial case data is used to demonstrate the shortfalls associated with low-quality agglomeration and the benefits of improved agglomeration which range from enhanced porous structure (better percolation and drainage characteristics) to better metallurgical response (faster kinetics and higher metal recovery). Proper agglomeration has been used to render otherwise untreatable ores into valuable leaching resources.

Feb 9, 2024

By Kerry Gee, Gary Colgan, James Fricke

Introduction Elevated zinc concentrations are observed in groundwater within alluvium adjacent to Silver Creek east of Park City, Utah. The study area is located in a small valley one and one-half miles northeast of Park City, Utah in Summit County, Utah (Figure 1). Although surface water concentrations in Silver Creek are typically less than 1 mg/l, groundwater concentrations have been measured as high as 85 mg/l in a near neutral pH environment. The elevated zinc concentrations in groundwater result from several factors including: (1) dissolution of zinc from tailings exposed at the surface and within the alluvium, (2) oxidizing conditions created by surface/ground-water exchange, and (3) ideal geochemical conditions for the dissolution of zinc-containing minerals. These ideal conditions include readily soluble minerals, available anions for complexation, and lack of available surface adsorption sites.

Jan 1, 2005

By Fred W. Brackebush

In underground stopes that require more than minimal support, backfill is almost universally used. The term cut and fill stopingis used in a broad sense in this section, which describes underground mining methods requiring support. Support in stopes can be classified as local or short-term and general or long-term. Local support for the back of a stope, for example, can be accomplished with rock bolts or timber stulls. General support for the walls of the stope is provided by backfill. Local support provides a safe working place for the stope miners. General support, provided by backfill, preserves the access way to the stope and prevents large scale dilution of ore. Supported methods are a set of cut and fill stoping methods using backfill for general support and various local support methods. his section is subdivided into three chapters: 19.1 Cut and Fill Mining 19.2 Excavation Techniques 19.3 Backfilling Methods

Jan 1, 2008

The primary use of coal in the US is for electric generation. The problems associated with the use of this vast amount of coal is the central theme of these sessions. The problems discussed include: production capacity, mining problems, coal cleaning, transportation, combustion, and various environmental problems, such as health effects of coal combustion, water and air pollution, and solid waste disposal.

Jan 1, 1979

By Silvano Morelli, Giovanna Cassani, Renzo Bindi, Antonio Nicola

More than 70 km of main line and service tunnels have been excavated to date for crossing the Apennines between Bologna and Florence. A new design and construction approach, known as Analysis of the Controlled Deformation in Rock and Soils, (ADECO-RS), was adopted to tackle the extreme heterogeneity of the ground and the particular stress-strain conditions. The goal of this system is to obtain constant and predictable full section advance rates, even in very poor geology, with the highest possible level of safety and reliability. The execution of this gigantic project required the mobilization of 21 job-sites, with the concurrent operation of 30 excavation headings. The global production rates confirm the high quality of the design and the high level of industrialization reached during the construction stage, levels not previously obtained in similar conditions, using other approaches such as NATM.

Jan 1, 2003

By Bhaskar B. Thapa, Christopher Laughton, Michael P. Bruen

At Fermilab, located in Batavia, Illinois, a 4,000-foot underground complex of tunnels and caverns is being excavated on a decline of six percent, at depths of up to350 ft, below grade. The site geology consists of dolomitic and shale formations overlain by glacial till. Since the start of construction in March 2000, work to date has concentrated on the excavation and support of the Target Hall cavern, which is characterized by a low rock cover and a final lining of shotcrete. Ground vibrations, noise levels, and rock movement were monitored during excavation by drill and blast methods to prevent damage to experimental facilities, impacts on surrounding communities, and to allow evaluation of cavern performance. The cavern design was based on a UDEC numerical analysis that was validated during construction by comparison to encountered conditions and measured cavern movements.

Jan 1, 2001

The nature of adsorbed calcium carboxylates (oleate and stearate) has been investigated by in-situ/ex-situ Fourier transform infrared internal reflection spectroscopy (FTIR/IRS). Previous spectroscopic studies in alkaline solution have shown that adsorbed carboxylate is characterized by a C-O stretching vibration at about 1550 em?1 for less than monolayer coverage. Similar results were found in this study. More specifically, in this study such a singlet at 1550 cm-1 was found for LB monolayers of calcium distearate transferred as a condensed layer at a high film pressure to the surfaces of fluorite and germanium. Normally the spectrum of bulk calcium distearate reveals a doublet at 1575 and 1540 cm-1, characteristic of a three dimensional 7-fold coordination for calcium carboxylate complexes. This doublet is generally found for carboxylate multilayers formed by spontaneous adsorption at the surface of calcium minerals. In this regard, the spectral evidence suggests that whenever the calcium dicarboxylate is constrained at a surface as a condensed layer, the 7-fold coordination can not be satisfied and the surface carboxylate is forced into a two dimensional symmetrical coordination with a singlet at 1550 cm-1. On the other hand, if the Langmuir-Blodgett (LB) monolayer calcium distearate film is transferred at a low film pressure the doublet is observed. This analysis is further confirmed by the spectral results for LB transferred calcium distearate monolayers at a hydrophobic silicon surface. Even though these are condensed monolayers formed at high film pressure, the carboxylate group, oriented away from the surface, is no longer constrained by the surface force field, and thus exhibits the characteristic doublet of the bulk calcium distearate salt.

Jan 1, 1998

By J. Noll, J. A. Organiscak, A. B. Cecala

"In recent years, significant strides have been made to optimize the design of filtration and pressurization systems used on enclosed cabs of mobile mining equipment to reduce respirable dust and other contaminants and provide the best air quality to the equipment operators. This synergetic effort has involved original equipment manufacturers building mining equipment, manufacturers of heating, ventilation, and air conditioning systems for mobile equipment, filtration and pressurization system manufacturing companies, as well as the National Institute for Occupational Safety and Health, and other government organizations. Considering all the advances made in this area over the last decade, one aspect that NIOSH still needs to assess is the longevity of optimal cab performance with respect to the quality (filtering efficiency) of the filters used in filtration and pressurization systems. In today’s culture, most health and safety professionals automatically believe that HEPA quality filters need to be used to provide the greatest level of protection to workers. Researchers at the Office of Mine Safety and Health Research for NIOSH hypothesized that HEPA quality filters may not be optimal for the mining industry and speculated that MERV 16 rated filters would be more appropriate in most cases. In order to test this hypothesis, NIOSH performed a two-year study comparing both HEPA and MERV 16 quality filters on two pieces of underground limestone mining equipment, being a roof-bolter and face drill machine. Testing showed at the 95 pct. confidence level that there was no statistical difference between the two efficiency filters on both pieces of mining equipment. Since the MERV 16 rated filters were less restrictive and provided greater cab pressure, and since they did not have to be replaced as often as the HEPA quality filters, researchers concluded the MERV 16 filters were the optimal choice for both pieces of mining equipment in this case study comparative analysis. INTRODUCTION When most health and safety professionals today think about filtration efficiencies and their correlation with protecting workers’ health, the normal assumption is the higher the efficiency of a filter, the greater the protection afforded to the workers. The next logical step is to believe that HEPA filters deliver the greatest protection for workers because they provide the highest filtering efficiency. Obviously high-efficiency intake filters are a necessity for an effective cab filtration and pressurization system on mobile mining equipment, but what is the optimal filter efficiency rating for achieving high levels of cab protection factor performance over the service life of filters? To address this question, the National Institute for Occupational Safety and Health (NIOSH) has performed an in-depth laboratory research study over the years simultaneously with numerous field studies to retrofit used enclosed cabs on mobile mining equipment with newer and more effective filtration and pressurization systems."

Jan 1, 2016

By Ashutosh Kumar Bharati, Rajesh Rai, B. K. Shrivastva, Arunava Ray

Opencast mining method is one of the most productive mining methods available at present, which is generally associated with the removal and handling of a huge amount of overburden material. Hence it imposes a serious challenge of dump slope stability and that too, mainly in the case of internal dumps. The study is primarily focused on the stability of dragline dumps and the subsequent development of a rating system to classify the stability of dragline dump profiles. Initially, numerical simulation is executed through RS2 (Version 9.0) software, which is based on the finite element method. Thereafter, simulation results are used to perform the sensitivity analysis of various geometrical and strength parameters of the dump slope, and the two-factor interaction method is also incorporated into the analysis, this method included the dependency of closest parameters while calculating the sensitivity index, and thereafter, it is converted into the rating of each parameter. The strength parameter like the angle of friction and the geometrical parameter like slope angle of the bench between the coal-rib roof and dragline sitting level are assigned the highest rating value. Based on the overall rating of the dragline dump, the dump slopes are classified into various classes, viz., very safe, safe, vulnerable, unstable, and highly unstable. This classification proved to be handy in the quick estimation of the stability of the dragline dump and also gives an idea of designing optimum and safe dragline dump profiles. The developed classification chart has been validated by the previous research works and has found similar results.

Feb 15, 2021

By I. Abdullayev, M. Soberano Capistran, J. Garcia

The application of post-tensioning in segmental structures was introduced in the early 1900s and has been successfully applied in different types of structures including immersed tunnels, bridges, buildings, metro stations, and stadiums. There are, however, only five known circular concrete tunnel projects where the post-tensioning approach has been adopted. This paper discusses the application of post-tensioning to mitigate the high internal operating pressures in an effluent outfall tunnel project 7 miles, 11.3 km long, currently under construction for the Los Angeles County Sanitation Districts, LACSD. This project will be the first use of post- tensioned segmental concrete tunnel linings in North America.

Jun 23, 2024

By TUIJA MONONEN, LUDGER BENIGHAUS, CHRISTINA BENIGHAUS, Virginia del Rio, SARI KAUPPI, JUHA M. KOTILAINEN, JAVIER GÓMEZ, JARI LYYTIMÄKI

The understanding of public debates over mineral exploration and mining largely originates from exceptional situations such as mining accidents of conflicts. Less is known about how mining is portrayed and understood under more conventional settings. What storylines dominate the local day-to-day public debate? This article presents results from a comparative case study focusing on newspaper coverage of mineral exploration and mining in three European countries representing different geological and socio-economic contexts. Newspaper articles from the Geyer-Erzgebirge region in Germany, the Andalusia region in Spain, and Northern Finland are studied. The sample looks into the period between September 2018 and February 2020 and shows that regional newspapers report about mining issues relatively intensively even in the absence of major accidents or other media events causing peaks of attention. The tone of the articles is generally neutral to positive towards mining activities, reflecting the specific local settings, historical experiences, and future expectations. Despite the different contexts of the three countries, there were considerable similarities to the topics highlighted, including common themes of mining revival, mining events and social interaction, history of mining, and damages related to mining. Past, present, and future employment opportunities related directly or indirectly to the mining sector are key storylines. Another recurrent underlying theme is the need to balance environment and safety risks and socio-economic prosperity, typically covered through ordinary disputes among the mining sector, public authorities, regional non-governmental organizations, and local initiatives.

Jul 6, 2021

By James Corcoran, Richard McLane, Matt Neuner, Joseph DeMello, Hugh Davies

The Los Angeles County Metropolitan Transportation Authority (LA Metro) Purple Line Extension Section 1 (PLE1) is a $3.12 billion USD design-build, underground heavy rail project, connecting an existing station at Wilshire Blvd. and Western Ave. and extending 3.92 miles under Wilshire Blvd, terminating approximately 550 feet west of Wilshire and La Cienega Blvds. The project alignment runs immediately adjacent to the La Brea Tar Pits, world renowned for Pleistocene fossils and continuous seepage of asphaltum (locally known as tar) and gas in an urban setting. This paper presents a successful case history of the planning, design, and construction efforts to safely construct the bored tunnels through Reach 3 of the alignment (between Wilshire/Fairfax Station, and Wilshire/La Cienega Station), in a designated Methane Zone in the City of Los Angeles. Historical context on decades of challenges and studies is summarized. Further, this paper outlines the pro-active partnership between the Owner: LA Metro, the Design Builder: Skanska-Traylor-Shea Joint Venture, and geotechnical design services provided by Golder Associates to safely manage pressurized face tunneling through a confined gas zone near the La Brea Tar Pits. Specifically, a program of in-situ oxidation and soil gas extraction was designed to test and analyze risks associated with pressurized face TBM tunneling through the complex subsurface geological conditions, then implemented during construction. In advance of tunneling, a network of wells was used to draw air into the gas zone to oxidize the 6,500 ppm hydrogen sulfide gas, as well as determine methane recharge rate. During TBM tunneling, the wells were converted to a gas extraction system to evacuate, filter (H2S) and burn (CH4) the gas as the Tunnel Boring Machine passed, providing a preferential pathway for the gas to migrate toward extraction wells, and preventing the migration to adjacent buildings. The team extracted and treated 3,857,000 cubic feet of mostly methane gas over 40 days as the TBMs passed through the zone. Gas behavior, pressures, and concentrations were monitored not only from the extraction system, but also in basements and utility vaults along this section of the alignment.

Jun 13, 2023

Many mining operations generate seismic signals. They come from blasting and from underground mine failures such as rockbursts, longwall first caves, coal bumps and pillar collapses. Traditionally, seismic motions have been of concern on a local scale because they could create damage to structures at the mine site or at neighboring locations. Recently, there has been much interest in the Comprehensive Nu-clear-Test-Ban Treaty (CTBT). It prohibits any kind of nuclear explosion, anywhere. So distinguishing signals of mining operations from a possible nuclear explosion becomes important. An international monitoring system (IMS) is being implemented to verify the Treaty when it is ratified. It includes a large number of seismic stations capable of recording signals at regional (200 to 2,000 km or 124 to 1,240miles) and teleseismic (more than 2,000 km or 1,240 miles) distances.

Jan 1, 2000