Search Documents

By S. Chai

Waste dumps are widely used to discharge stripped mine wastes in open pit mining methods. As mining progresses, the height of the waste dumps will increase gradually, which may induce sliding failure once the height exceeds a critical value. Therefore, estimation of the maximum dumping height is crucial to the life-cycle use of a waste dump. However, published information about the maximum height of mine waste dumps are extremely rare. In this study, the maximum dumping height is estimated based on the strength-reduction technique by numerical simulations. The influences of dump geometry and properties on the maximum height are investigated. The results show that the maximum dump height decreases as the dump slope inclination angle α or the unit weight of dump materials γ increases, but decreases when the shear parameters of dump materials (cohesion c and internal friction angle ϕ) increase. The maximum height starts to increase with the ground inclination β when shear failure occurs at the interface between the dump and the base. Furthermore the effects of the dump width B, Young’s modulus E, and Poisson’s ratio μ of dump materials on the maximum height are almost insignificant. Good agreement was found between numerical results available in the literature and those obtained in this study.

Oct 1, 2022

By R. B. Khumalo, T. Chauke, T. Mtshali, F. K. Mulenga, B. Makgate, N. M. Chiloane, T. Moyane, V. C. Madanda

While high production rates are important for the profitability of a mine, the influence of geotechnical engineering cannot be ignored. In block caving, a high-stress level is required for cave propagation; this is one of the core elements for ore recovery. Therefore, stress distribution and geological structures play a major role in the planning and layout design of the mine. This paper explores the influence of stress and geological features on the design of the mine from the feasibility study phase. The geology and stress measurement of the mine were determined through logging and overcoring, respectively. This study found that while production rate is the primary operational consideration, the long-term layout design of the undercut face advance, face angle, drawpoint spacing, and undercutting sequence is mainly governed by the stress orientation and major geological structures. Moreover, widely spaced drawpoints result in isolated draw zones, consequently, resulting in ore loss and early dilution whereas closely spaced drawpoints affect the stability of the major apex pillar. This paper also provides insight into how operations can leverage stress distribution to optimise mine layout and safety in massive mining methods.

Nov 24, 2025

By J. Hadjigeorgiou, J. Wesseloo

Mining companies employ a multitude of risk management tools. The effectiveness of these tools for decision-making and communicating risk has not been addressed. This paper investigates the use of verbal probabilistic expressions in communicating geomechanical risk. Analysing survey data obtained from a group of mining geomechanics professionals, it identifies limitations of common probabilistic expressions. The paper concludes by making specific recommendations to avoid the use of certain expressions that may result in increased uncertainty, thus compromising the use of risk management tools.

Jan 30, 2026

By M. J. Voigt, R. A. Govender, A. Mainza, L. Bbosa

"Mineral texture is a critical factor which controls ore variability and is an important attribute in geometallurgy. In relation to downstream processes, it affects the fracture pattern during breakage, where rock strength is inherently a function of mineral texture. Because of the subjective nature of mineral texture, it has not been easy to quantify, especially in the context of a measurement suitable for use in geometallurgical programmes. The aim of this paper is to present the first steps in developing a 3D mineral texture quantification method for drill core and to assess its sensitivity to differences in rock strength using a case study. The methodology includes classifying the textural information using the 3D grey level co-occurrence matrices (GLCM) and X-ray computed tomography (XCT) coupled method. Rock strength tests were performed using the split Hopkinson pressure bar (SHPB). The case study investigates a heterogeneous polymetallic sulphide deposit and a homogeneous shale subdivided into three ’mineral textural types’. The variability is largely captured by the GLCM matrices, and preliminary trends can be observed where the shale is finer grained and has a higher yield strength in comparison with the coarser grained polymetallic sulphide ore. IntroductionModern mining requires the exploitation of lower grade and more complex, heterogeneous orebodies to address the growing industry demands. Historically, processing plants were designed and built based on average ore characteristics and therefore are relatively inflexible when facing the full spectrum of ore variability in heterogeneous orebodies (Lamberg, 2011; Lotter, 2011; Schouwstra et al., 2013). The practice of geometallurgy represents an opportunity to manage ore variability in the mining industry (Powell 2013; Baum, 2014; Yildirim et al., 2014; Nguyen, 2013). It focuses on quantifying the relationships between ore characteristics and their downstream mining and processing responses, often starting with small-scale laboratory testing. The purpose of geometallurgy is linked to maximizing the net present value (NPV) of an orebody by minimizing technical and operational risk – where ‘ore variability’ is considered one of the most significant technical risks."

Apr 1, 2019

By T. Z. Sehume, J. R. Bunt, J. C. van Dyk, C. A. Strydom

"SynopsisCo-pyrolysis of four biomass samples (hardwood chip, softwood chip, pinewood chip, and sugarcane bagasse) with an inertinite-rich medium rank C South African coal was investigated. Proximate and ultimate analyses of the chars prepared using a heating rate of 10°C/min up to 1100°C in a nitrogen atmosphere were used to compare the properties of the biomass and the coal chars. Similar gross calorific values (28.5–29.1 MJ/kg) for the woody biomass-coal blended chars were observed, which were slightly higher than that of the coal char sample (26.5 MJ/kg). CO2 surface areas of the chars of the woody biomass samples (328.1–329.4 m2/g) and of the blends (238.5–271.5 m2/g) were higher than that of the coal char sample (94.2 m2/g). Thermogravimetric (TG), differential thermal analyses (DTG), and calculated weighted averaged TG curves indicated that the influence of the biomass on the pyrolysis rate of the coal is small and vice versa. The CO2-producing reactions of the coal were slightly enhanced during co-pyrolysis.IntroductionCoal utilization has led to rising concerns about adverse impacts on the environment (global warming) caused by toxic gases (H2S, SOx, NOx, and CO2) and remaining waste. Biomass is considered to be CO2-neutral with regard to the greenhouse gas balance, and is regarded as a renewable source that assists in reducing CO2 emissions when compared with coal (McGowan, 1991; McKendry, 2002). Biomass currently makes up approximately 14% of the world’s energy sources (McGowan, 1991; McKendry, 2002). Coal combustion and gasification are prominent processes in South Africa (in producing synthesis gas and energy) due to the abundance of coal in the country. Some of South Africa’s coal resources are, however, high in ash content and also are inertinite-rich, which renders them more difficult to use industrially than vitrinite-rich low-ash coal (Jeffrey, 2005; Strydom et al., 2011). There is a need to investigate the properties and behaviour of the inertinite-rich high-ash South African coals and especially their interaction with local biomass sources. The gasification process occurs through various stages, of which pyrolysis of the char residue forms an integral part (Bunt and Waanders, 2009). Currently, particular interest is shown in the co-utilization of coal and biomass to produce synthesis gas via the gasification process (Usón et al., 2010; McGowan, 1991; McKendry, 2002). Investigating the co-pyrolysis of the South African coal and local biomass material is thus the first step in evaluating the use of local biomass sources for co-gasification purposes."

Jan 1, 2015

By J. O. Claassen

"SynopsisMining value chains are dynamic systems and should be managed according to systemic flow-based principles. This includes a detailed focus on the impact of variable geological conditions on material flow, product quality, and production cost, visibility of the total mining system to operators and managers, as well as the synchronization of resources and activities in downstream processes. Thirty mining operations across the African continent were studied to establish to what extent systemic flowbased principles are applied in day-to-day operations. The study indicated that although most mining operations have identified the relevant geoprocessing variables, only a small number apply this information in a flow-based management approach. Most mining operators do not focus on developing a clear flow view of the mining value chain and on making it visible to operators and managers to enable them to optimally set and reset operations. Daily synchronization of geoprocessing variables is limited to a small number of variables, e.g. synchronizing ore hardness with drilling or milling requirements, in less than 30% of the operations evaluated. Operations where these principles have been adopted reported a noteworthy improvement in performance. The study indicates that notable potential exists in most of the operations evaluated to implement flowbased management principles, including geometallurgical principles. This can significantly improve value chain performance without exorbitant capital layouts and enhance ROCE. IntroductionObjective of the studyThe study seeks to establish to what extent systemic flow-based principles have been adopted in the southern African mining industry and the implications thereof. Specific attention is given to the importance of defining and managing geoprocessing dependencies (geological variables directly impacting mining and plant performance – the geometallurgical approach), establishing a flow view of the mining system, which typically includes a dashboard of the flow of ore/product quality and cost from the mining face to the customer, and limiting the impact of dependencies through synchronization of activities and resources, e.g. ensuring that a continuous miner does not wait for a roofbolter, or that reagent addition rates are matched with a specific ore/concentrate composition."

Jan 1, 2015

By V. Yahorava

Efficient recovery of precious metals from process solutions is essential for improving process economics. Traditionally, precious metals are relatively effectively recovered from waste streams via precipitation or cementation. However, these approaches have a number of drawbacks, including poor water balance, creation of environmentally unfriendly waste streams, and losses of precious metals. Ion exchange technology is an alternative for the recovery of precious metals from waste or low-grade streams. This technology allows the recovery of the precious metals to extremely low levels (micrograms per litre) with relatively high upgrade ratios from the solution onto the resin without major water balance concerns, while the impact on the environment could be minimized or avoided. Research was conducted on the recovery of platinum group metals and gold from different low-grade and waste streams from one of the precious metals refineries in South Africa by means of ion exchange. Various functionalities and matrices (granular and fibrous) of ion exchange materials were evaluated. The results from these studies indicated that in some cases ion exchange could be very effective for the recovery of precious metals, and that the PGM concentration could be reduced to < 1 mg/L. The upgrading ratios of the various PGMs onto the specific fibres were relatively high for the specific streams evaluated, which might in some cases justify incineration of the loaded material instead of stripping and recycling the adsorbent. The cost of direct incineration for one of the waste streams tested would be less than 1% of the value of the PGMs recovered. However, the adsorbent has to be carefully selected and the process design optimized for each specific stream.

Jan 1, 2014

By M. A. El-Sayed

"Double oxide films (bifilms) are significant defects in light alloy castings that occur when, during melt handling, the oxidized surface of the melt is folded over onto itself and then entrained into the liquid metal, encapsulating a portion of the local atmosphere. These defects create crevices in the final castings and have been shown to decrease tensile and fatigue properties, and also to increase their scatter, making casting properties unreproducible and unreliable. This paper reports on two different experiments performed to study the behaviour of such defects in Al alloys. In the first experiment and as a proxy for a bifilm, air bubbles were held in an Al-5Mg alloy melt for varying periods of time before the melt was allowed to solidify. The composition of the gas content of the bubbles was subsequently analysed using mass spectrometry to ascertain how it changed with time. In the other experiment the influence of the age of bifilms on the mechanical properties of Al-5Mg castings was assessed by holding castings in the liquid state for different times before solidification, followed by mechanical property testing and SEM and EDX studies of the fracture surfaces of tensile test bars. This research could provide a better understanding of the behaviour of double oxide film defects, and may lead to the development of new techniques by which these defects could be eliminated, or at least deactivated, in light alloy castings. Introduction One of the major structural defects affecting the reproducibility of mechanical properties of aluminium castings is the double oxide film defect (El-Sayed and Essa, 2017; El-Sayed and Ghazy, 2017). This type of defect is usually created as a result of poor filling system design. Owing to the very high reactivity of liquid Al-Mg alloy with oxygen in the air, the surface of the liquid metal can be considered to be permanently coated with an oxide film (Weigel and Fromm, 1990). As a consequence of surface turbulence, the oxidized metal surface can become folded over onto itself, but not fused, and then submerged into the bulk liquid, with a portion of the mould atmosphere being entrapped within it (Campbell, 2003; Al- Sayed, 2016; El-Sayed, Hassanin, and Essa, 2016)."

Nov 1, 2018

By P. J. Le Roux

"Mining companies are under constant pressure to reduce their cost structures to sustain profitability. In mines using an open stoping mining method, dilution often has a significant effect on profitability. At Target mine in South Africa, dilution in some open stopes was found to exceed 10%, falls of ground being a major contributor to the problem. This dilution can reduce the recovered grade from 5.5 to 4.5 g/t, resulting in a potential loss of about R21 million per month based on a gold price of R240 000 per kilogram. In addition to the cost of dilution, the cost of damage to, or loss of, trackless equipment as a direct result of falls of ground in open stopes is significant. Other associated costs include transport, hoisting, secondary blasting, milling, and plant treatment of waste material. Stable open stopes are essential in order to reduce falls of ground. Back-analyses of stope instability at Target mine have indicated that conventional rock mass failure criteria are unsuitable for stope design. An alternative strain-based criterion has been developed, and has proved to be very successful, allowing the stability of open stopes to be calculated reliably. Since its implementation in 2010, dilution and equipment damage have decreased markedly, creating value for the mine. IntroductionMines that make use of an open stoping mining method aim to extract only the ore, leaving the waste behind. Many orebodies have well-defined boundaries between the ore and the waste rock. In such orebodies, the introduction of waste into the ore due to overbreak dilutes the grade. In massive disseminated orebodies, dilution is less problematic. Overblasting, falls of ground, or other causes may result in dilution. A study undertaken in Canada (Pakalnis et al., 1995) found that approximately 51% of all underground metal mines utilized open stoping mining methods and, from surveys conducted at these mines, open stoping operations experienced dilutions of up to 20%, and occasionally more. Dilution of this magnitude has a significant economic impact on any mining venture. Research carried out in Australia by Capes (2009) came to the same conclusion."

Jan 1, 2017

By G. Jandieri

An improved methodology is presented for assessing the economic feasibility and effectiveness of recycling industrial waste. The methodology is based on the break-even control mechanism, but at the same time provides for the introduction of new evaluation criteria such as the threshold of conditionality and the degree of ore substitution. Based on an improved analysis, it becomes possible to more precisely predict recycling efficiency. A more refined determination of the lower limit of concentration of recoverable metals, at which technogenic waste can be assigned the status of secondary raw materials and processed profitably, leads to a significant expansion of the secondary raw material base suitable for recycling. The potential for recycling manganese-containing dust from the production of ferrosilicomanganese, dehydrated sludge from the hydro separation of slags, and cake from the production of electrolytic manganese dioxide at the Chiatura mining enterprise is used as an example. It is shown that with a threshold of –24% Mn content, the highest recycling efficiency can be achieved by the production of low-phosphorus manganese slag and conversion to ferrosilicomanganese using the above waste to replace 40-60% grade III and IV manganese concentrates in the feed.

Jan 26, 2023

By H. Askari-Nasab, S. Upadhyay, A. Moradi-Afrapoli

Material handling in surface mines accounts for around 50% of the operational cost. Optimum truck dispatching plays a critical role in the reduction of this operational cost in truck and shovel surface mines. Researchers in this field have presented several mathematical models to solve the truck dispatching problem optimally. However, a critical survey of the literature has shown that three significant drawbacks exist in the available truck dispatching models. The published models underestimate the importance of the interaction between truck fleet, shovel fleet, and the processing plants. They also disregard goals set by strategic-level plans. Moreover, none of the available models account for the uncertainty associated with the input parameters. In this paper we present a new truck dispatching model that covers all of these drawbacks, using a fuzzy linear programming method. The performance of the developed model was evaluated through implementatin in an active surface mining operation. The results show a significant improvement in production and fleet utilization.

Sep 1, 2021

By S. Govender, J. J. L. du Plessis, R. C. W. Webber-Youngman

Spontaneous combustion (SC) is a cold oxidation reaction that generates heat, causing a temperature rise of the reactant and leading, with limited heat dissipation, to self-ignition of the reactant, which occurs without an external heat source. Although not limited to coal, the most significant hazard of SC are the fires that occur in coal mining operations around the world. These fires pose a serious risk to the safety of workers in the mines as well as adverse effects on the environment, and can affect the quality of life for current and future generations. We investigated the occurrence of SC in raw coal storage bunkers with the purpose of compiling a decision analyser for engineers designing or working with coal storage bunkers. Specific experts were interviewed from different backgrounds and companies, followed by field research at a coal mine. The important factors affecting the possibility of SC occurring were the type of coal supplied to the bunker, the mining practice, and physical conditions around the bunker. The information presented here will assist in reducing the SC risk in raw coal storage bunkers. These findings, together with the systematic decision analyser developed, will assist design engineers and mine personnel to take early preventative steps in managing SC. The decision analyser was tested for many different scenarios and gave good guidance on how to minimize and prevent SC in bunkers

May 1, 2021

By F. Dinter, S. A. C. Hockaday, Q. G. Reynolds

The thermal decomposition of carbonate minerals as pre-treatment before smelting reduces the energy requirement for smelting. It can also make the combustion of fossil fuels for heating unnecassary. Thermal decomposition may become important in reducing greenhouse gas emissions when producing ferromanganese alloys while simultaneously reducing electrical energy demand during smelting. A kinetic reaction rate model for the thermal decomposition of manganese ores is presented, based on published reaction rate kinetics for the decomposition of manganese oxides and calcium carbonate. The model was validated against thermogravimetric data for two carbonaceous manganese ore samples and one ferruginous manganese ore sample. The reaction rate model shows that carbonate minerals in the manganese ores are decomposed at temperatures above 900 °C while pyrolusite is decomposed at temperatures from 450 °C to 500 °C. Mn2O3 decomposes rapidly at 550 °C. Braunite decomposition at temperatures below 1000 °C was negligible. The presence of organic carbon in the samples led to further reduction of the samples during thermal treatment.

Aug 3, 2023

By T. Nghipulile, M. Moys, M. Bwalya, H. Simonsen

The quest for efficiency in comminution is an ongoing concern as comminution usually constitutes a major cost component in the metal production industry. Such improvements can be made by circuit optimization or development of more efficient equipment. A novel crusher, known as the rotary offset crusher (ROC), promises to deliver in this space. The ROC was invented in 2002 by Michael Hunt, Henry Simonsen, and Ian Sinclair, but failed to garner enough support to progress to production. The original design concept was recently rekindled, and a laboratory version of the crusher has been built and commissioned at the University of the Witwatersrand. The crusher is simple in design, with two cylindrical discs that are parallel to each other, and, as the name implies, there is an offset between the vertical axes of the discs. The top disc has a conical section on its lower face, and this creates a crushing zone between the opposite faces of the two spinning discs. Centrifugal motion transports particles through the crushing zone. Batch experiments have been conducted with quartz at various crusher settings (discs offset, rotational speed, and vertical exit gap) for various feed size distributions. The indications so far suggest that the disc speed is a key factor affecting the performance. Size reduction ratios as high as 11 were recorded from experiments with quartz at a speed of 830 r/min.

Jan 1, 2021

By M. J. Kanda, T. R. Stacey

Thin spray-on liners (TSLs) have been used as sealants and rock support in tunnels for over 25 years. Laboratory tests have indicated satisfactory properties that can provide adequate strength, adhesion, toughness, and elasticity as part of rock support systems in mining excavations. These characteristics are, however, not always demonstrated in practice, when mine environmental conditions do not correspond with laboratory environmental conditions. The shortcomings of TSLs experienced in the mining industry have raised concerns, resulting in scepticism from some operators regarding their utilization. The research described in this paper aims to investigate TSL performance in environmental conditions similar to those experienced in mines. Brazilian indirect tensile (BIT) specimens were prepared from precast shotcrete and coated with TSLs. The specimens were then exposed to different environmental conditions for up to 112 days before BIT testing under various conditions: laboratory room temperature and humidity; saturated room temperature; and combined saturated and high temperature (50°C). Additional uncoated shotcrete and TSL BIT specimens were prepared for comparison purposes. The results of the BIT tests showed that environmental conditions have a significant influence on the tensile strength enhancement of shotcrete by TSLs. Water-based TSLs are most likely to be suitable for high humidity environments, although their performance decreases at higher temperatures. Numerical modelling of TSL-coated BIT samples confirms the potential limitations of designing TSL support based only on laboratory testing carried out under room conditions.

Jul 1, 2021

By I. James, R. J. Durrheim, M. S. D. Manzi, O. Valeshin, J. Lepine, L. V. Socco, C. Colombero, A. Malehmir, M. K. Rapetsoa, M. Sihoyiya

The FUTURE project aims to enhance seismic surveying in South African mining by integrating advanced acquisition technologies. In this paper, we detail surface and underground seismic surveys at the South Deep gold mine as part of the project. Surface seismic acquisition used co-located broadband micro-electromechanical sensors, one and three component recorders connected to geophones, distributed acoustic sensing using a straight fibre optic cable, along with a 6 ton broadband seismic vibrator operating with 4–180 Hz linear sweeps. In addition, underground surveys employed a combination of straight, and helically wound fibre optic cables, cabled-based and nodal sensors, along with a 500 kg drophammer mounted on a skid steer bobcat. The surface and underground seismic arrays were time synchronised using a GPS-time transmitter to allow for accurate seismic data recording in a GPS-denied environment. Results show the efficacy of these techniques in acquiring high-resolution seismic data, revealing detailed subsurface geological structures and mineralisation down to 3500 m below ground surface. Surface data revealed clear seismic reflections corresponding to the Black Reef and Ventersdorp Contact Reef. An underground P-wave velocity model exhibits low velocity anomalies that are associated with fracturing, while a P-wave reflection stack section shows significant reflections and a degree of faulting below the tunnel floor that was not observed on the surface reflection seismic data. We highlight the potential of these technologies to enhance safety, efficiency, and sustainability in mining. This study sets a benchmark for future reflection seismic surveys, paving the way for safer, more efficient, deep mineral exploration and extraction practices.

Jan 12, 2025

By B. P. Watson, T. J. Maphosa, D. P. Roberts, L. J. Gardner

The results of FLAC3D modelling on chromitite Upper Group 2 Reef pillars from the Bushveld Complex of South Africa are described. The model input parameters were determined from laboratory triaxial tests with post-failure measurements. These geomechanical tests were performed on rock materials within the pillars and the immediate pillar foundations. In the models, postfailure behaviour was simulated using the concept of cohesion softening. Models were built to determine the strength and behaviour of pillars with a width-to-height ratio of approximately two. The original research aimed to find a suitable depth below the surface where Impala Platinum Ltd could safely introduce crush pillars; however, the paper only describes the model results: the ideal depth of the crush pillar introduction is not discussed. The results of the modelling are compared with the PlatMine formula for peak pillar strength and with an underground instrumented pillar located elsewhere on the same reef. Some insight into the effects of grid size on strength is also provided. Further underground measurements are recommended to verify the model results

Sep 9, 2024

By R. A. Wildenboer, R. F. Sandenbergh

Rare earth elements (REE) are present at concentrations of approximately 0.36 % in phosphogypsum stacks located in Phalaborwa, South Africa. The REE are present in the phosphogypsum in solid solution in the gypsum and as fluorine and aluminium rich precipitates. Recovery of the REE offers opportunities for valorization and reducing the environmental impact of the phosphogypsum waste. This paper presents the results of investigations into the leaching behaviour of rare earth elements and other impurities from phosphogypsum using aqueous sulfuric acid. The effects of acid concentration, temperature, residence time, and the influence of impurities were evaluated for their impact on the solubility of rare earth elements in a sulfate medium. It was found that a significant fraction of the REE can be leached from the phosphogypsum in a range of conditions much less severe than traditional hard rock rare earth processing conditions. The REE were leached at a sulfuric acid concentration of 110 g/l, temperature of 30°C – 40°C and a residence time of approximately 8 hours.

Nov 6, 2024

By P. L. Ngwenyama, W. W. deGraaf

South Africa is one of the leading producers and exporters of coal globally. A significant amount of the country’s production is obtained from previously mined underground bord and pillar workings. This coal is in the form of pillars and remnants on the roof and floor of the old workings. The good quality coal pillars were left behind as primary support during underground bord and pillar mining operations. Due to the depletion of virgin coal reserves, the pillars and remnant coal are now removed using opencast mining rather than underground methods. However, the secondary extraction of pillars and remnant coal from the old workings using opencast methods entails some serious challenges that have a negative impact on the safety and productivity of the operations, affecting both personnel and machinery. If these risk factors and challenges are managed properly, then the opencast mining operations could remove the pillars safely at recoveries competitive with those of virgin coal operations. In this study we review the recurring challenges affecting opencast pillar mining by means of field investigations and consultations with experts at five opencast pillar mining operations, and evaluate the best practices used to combat these challenges. It was found that each mine has its own unique conditions and challenges.

Dec 1, 2021

By Roger A. Blais, Michel David

"Matheron&apos;s geoslalislical method for the estimation of ore reserves has been developed to the point at which real-life problem may be handled effectively. The steps involved in the method are:(i) obtalning the variogram,(ii) fitting a model, and(iii) producing block estimates.All three steps may cause difficulty, and would-be users need a deep understanding of the theory if failure is to be avoided.To illustrate these points, specific cause are considered:(i) two almost equidimensional porpbyry deposits, one drilled randomly and the other regularly; and(ii) two iron formation, one drilled extensively and being mined, while the other is still at the stage of early estimation."

Jan 1, 2014