Search Documents

By P. Cowx, L. Els, P. Smith, R. Nordhagen

"Tapping operations at ferroalloy smelters generate a significant amount of fume. Effective capture of fumes is required to meet the obligations of environmental, as well as occupational, legislation.A study was completed on an existing fume extraction system at a ferromanganese furnace tapping area. The area under consideration included the tap-hole, launder, and ladle area. The study consisted of site test work as well as computational fluid dynamics (CFD) modelling to identify and evaluate solutions.Site test work and observations during furnace operation provided a baseline of system performance as well as input parameters for CFD modelling. Gas flow rates and energy contents from each extraction area were measured. Photographs and video footage were taken to evaluate areas of fume leakage.The CFD study was firstly validated against site observations to ensure the accuracy of input parameters. Thereafter several modification concepts were modelled and suitable combinations were investigated to ensure robust solutions. The following concepts were considered:•,Air curtains•,Ladle hood aspect ratio and position•,Increase of ladle extraction volume•,Extension of the length of the tapping garage structureThe paper presents the results of a performance test on a working ferromanganese tapping area fume extraction system and the results of CFD modelling as compared to site test results. Upgrade options are evaluated and an integrated robust upgrade of the system described."

Jan 1, 2014

By Huang Zhiwei, Paul Skayman, Kevin Holley

In 1989 The First Brigade for Geology and Mineral Exploration of Qinghai Province discovered gold at Jinlonggou and Qinlongtan, Tanjianshan. Between 1992 and 2002 small scale mining was carried out at these sites using underground mining methods at Jinlonggou and an open pit at Qinlongtan. During 2003 and 2004 geotechnical investigations were carried out in support of a bankable feasibility study. An important objective of this investigation was to meet both internationally accepted standards and codes of practice, and also to satisfy the Chinese requirements. Extensive use of local experience was utilised. Where possible geological drilling information was incorporated into the assessment. Extensive geotechnical mapping of surface and underground exposures, and index testing to gain an appreciation of rock intact strength were used to characterise the sites. Rock mass classification (MRMR) was used to assess indicative overall slope angles and appropriate bench stack heights for the proposed pits at Jinlonggou and Qinlongtan. Measured discontinuity orientations were used in kinematic analysis to assess stability of possible pit slope geometry at a batter and overall scale to provide preliminary recommendations for the pit slope configuration. Numerical modelling was also carried out to improve the understanding of anticipated pit behaviour. Site investigation and preliminary geotechnical design details, that incorporate site specific conditions for the formation of open pits at Tanjianshan, are discussed in this paper.

Jan 1, 2006

By B. H. Sandelowsky

Prehistoric metal-working in South West Africa by B. H. SANDELOWSKY*, Ph.D. (Visitor) This paper describes a three-hundred year old metal-working site at Rehoboth, and makes a plea for information on such sites elsewhere in South West Africa so that they can be investigated. The technique of ore smelting that was used at Rehoboth appears to be different from that practised elsewhere by Bantu peoples before the modern era.

Jan 5, 1974

By B. P. Watson

Uniaxial tests performed on core from instrumented sites at Amandelbult 1 shaft, Impala 10 shaft and Union Section Spud shaft showed a nonlinear elastic relationship between applied load and induced deformation. This nonlinear behaviour does not appear to be dependent on borehole orientation but in the case of the Amandelbult and Union sites appears to have been influenced by the stress condition of the rock mass at the time of drilling. Cores drilled at these two sites under destressed conditions, such as over a stope, showed a linear elastic response to the applied load whereas most of the cores drilled under relatively high radial stresses were nonlinear. The Impala 10 shaft tests, however, all showed strong nonlinear behaviour irrespective of the stress condition of the rock mass at the time of drilling, although high stress conditions may have influenced the severity of the nonlinearity. A comparison between underground stress change measurements and an elastic model indicated that the rock mass became nonlinear when the virgin stress condition was relaxed to about 10 MPa. The cores for laboratory testing were retrieved from vertical boreholes drilled up from the centre of a stope and from horizontal boreholes drilled over pillars and stopes at about 600 m, 1 100 m and 1 400 m below surface for the three sites respectively. The k-ratios under virgin conditions were estimated from sockets, modelling and stress measurements to be 1.0, 1.3, and 0.5 for the Amandelbult, Impala and Union sites respectively. Of the three sites, therefore, Impala 10 shaft appears to have had the highest virgin stress state. Tests performed on similar rocks from shallower depths at Impala Platinum essentially showed a linear relationship between stress and strain. From the small Impala Platinum rock test database available to the project, it appears that the nonlinear elastic behaviour initiates at this mine from about 1 000 m below surface and seems to become progressively more nonlinear below this depth. In addition, the nonlinear elastic rocks are weaker, have a lower Young?s modulus and a higher Poisson?s ratio than their linear elastic equivalents. Interestingly the tangential Poisson?s ratios of the nonlinear elastic materials are often greater than 0.5 at 50% of the failure stress, suggesting an early failure initiation. The paper describes the microscope and modelling work done to determine the causes of the nonlinear behaviour and discusses some implications of the behaviour for deep-level mining.

Jan 1, 2009

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By H. B. Arntzen, P. O. Grøntvedt, T. Lindstad, R. J. Ishak, M. Syvertsen

Better utilisation of electric power and coke is vital in reducing production costs and CO2-emissions in production of ferromanganese. All FeMn smelting operations consume 10 to 30 % more carbon than the carbon needed to reduce MnO and FeO to metal and the carbon contained in the alloy. Potassium which re-circulates and builds up in the furnace has been shown to be the main culprit causing both excessive carbon consumption, by catalysing the Boudouard reaction, and increased electric power consumption. The reaction between CO2 and ordinary metallurgical coke or coke impregnated with potassium has been studied at temperatures from 800 to 1100°C in a thermobalance apparatus. Ordinary coke did not react to any great extent at temperatures up to 1000°C, whereas the addition of potassium (2-10 %) resulted in a huge increase in reaction rates. The ultimate goal is to fit the results into a reaction rate model containing the equilibrium constant for the solid-gas heterogeneous reaction between CO2 and a free active site on the carbon reactant producing CO and adsorbed oxygen (an occupied site). The model includes the partial pressures of CO and CO2, a reaction rate constant that is a function of both the total number of reaction sites of carbon, and the potassium content. The potassium dependency is taken care of by introducing activity coefficients for the carbon sites. As the first step towards such a model, a regression line for the Boudouard reaction rate has been established.

Jan 1, 2004

By G. M. Thain

Ancient Mining - The following three contributions were received for publication in addition to the preceding papers. 1. Ancient gold-mining sites in the Transvaal G. M. THAIN* Pre-European gold mining and working in South Africa is a tantalizing field for conjecture. Well over thousand sites have been identified in Rhodesia, but here we have had to reach double figures, judging by published accounts. Geologically, the Transvaal is less amenable primitive exploitation, but it difficult to reject the idea that the knowledge gained to the north did not have its influence south of the Limpopo.

Jan 1, 1974

By L. D. Robbins, M. L. Murphy, A. C. Campbell, L. Murphy

This paper reports on what appears to be the first discovery of prehistoric mica-schist mining in southern 4frica. The mine concerned was found in a location very rich in rock art that is one of the most important archaeological sites in the Kalahari. The authors conclude that the oval pieces of mica schist that were found at the mine site were used by Khoisan peoples to scrape fatty tissue from hides that were to be cured. Radiocarbon datings seem to indicate that such ovals were used for at least 20 000 years.

Jan 1, 1994

By K. L. Riemer

The West Wits Line first began yielding gold in the mid-1930s and is among South Africa's leading gold-producing areas. Gold mining operations are carried out amidst the occurrence of seismic events which cause both damage to underground excavations and injury and loss of life to production personnel. The feasibility of establishing a system to minotor the seismicity on all the Gold Fields mines was investigated during the early 1980s. This led to the establishment of a centralized seismic network in 1981. The system was structured around three major objectives. It uses Perkin Elmer (now Concurrent Computer Corporation) 16 and 32 bit mini-computers. The hardware in use at both the central and remote sites is outlined, giving a good insight into the role of computers in the system. The system software reveals the fast flow of data through the network; it can be divided into three categories: (1) data logging and transmission - remote sites, (2) data capture and communications - central site, (3) applications and research - central site. Several examples are given which show how the system is measuring up to its objectives. These case studies also indicate how the computers are effective in representing the seismic data collected. It is concluded that the use of computers enables the pin-pointing of seismic events on the West Wits Line within about 3 -4 minutes of their occurrence. The choice of hardware is largely dependent on the objectives of system, and the Gold Fields Network has chosen mini-computers because of the speed of communication and the large amount of data and storage required for research applications.

Jan 1, 1987

By R. Xie, J. Liu, Y. Zhu, Y. Li

The surface chemistry features of spodumene and feldspar were investigated by XPS, zeta potential measurements and first principle calculation. The results indicated that the zeta potential of feldspar was more negative than that of spodumene. The most possible active sites on spodumene and feldspar were Al sites and O sites. However, the number, type and activity of these sites were different. The flotation behaviour of five new collectors (cationic collector decyloxy-propyl-amine (DPA), anionic collector α-bromododecanoic acid (α-BDDA), N-Dodecyliminodiacetic acid (DIDA), and mixed collector DPA-BDDA and DPA-DIDA) were investigated through micro flotation experiments and analysed based on the surface chemistry features of spodumene and feldspar. The results revealed that cationic collector DPA processed a high collecting capacity for both minerals. The highest recovery of spodumene and feldspar was 91.60% and 95.30% respectively. The anionic collector α-BDDA and DIDA showed poor flotation behaviour. The recovery of spodumene and feldspar when using α-BDDA as collector was less than 5% and when using DIDA as collector was less than 1%. For the mixed collector DPA-BDDA, the recovery of spodumene and feldspar was 82.27% and 32.61% respectively at pH 4.5. For mixed collector DPA-DIDA, the recovery of spodumene and feldspar was 35.69% and 9.08% respectively at pH 5.8. The results indicated that the cationic collector had high collecting capacity, but low selectivity. The collecting capacity of anionic collector for spodumene and feldspar was poor at the same concentration compared with cationic collectors. Mixed collector DPA-BDDA showed good flotation behaviour and selectivity on spodumene. The ―COO- in mixed collector might improve the selectivity. However, too much ―COO- would increase the electrostatic repulsion, which might cause low selectively and poor recovery. Keywords: Spodumene, feldspar, surface chemistry features, mixed collector, flotation

Jan 1, 2020

It is predicted that vast volumes of affected mine water will be produced by mining activities in the Mpumalanga coalfields of South Africa. The potential environmental impact of this excess water is of great concern in a water-scarce country like South Africa. Research over a period of more than 10 years has shown that this water can be used successfully for the irrigation of a range of crops (Annandale et al., 2002)1. There is, however, continuing concern from the local regulators regarding the long-term impact that large-scale mine water irrigation may have on groundwater quality and quantity. Detailed research has been undertaken over the last three years to supplement the groundwater monitoring programme at five different pilot sites, on both virgin soils (greenfields) and in coalmining spoils. These sites range from sandy soils to very clayey soils. The research has included soil moisture measurements, collection of in situ soil moisture over time, long-term laboratory studies of the leaching and attenuation properties of different soils and the impact of irrigation on acid rock drainage processes, and in depth determination of the hydraulic properties of the subsurface at each of these sites, including falling head tests, pumping tests and point dilution tests. This has been supported by geochemical modelling of these processes to quantify the impacts. The results indicate that many of the soils have considerable attenuation capacities and that in the period of irrigation, a large proportion of the salts have been contained in the upper portions of the unsaturated zones below each irrigation pivot. The volumes and quality of water leaching through to the aquifers have been quantified at each site. From this mixing ratios have been calculated in order to determine the effect of the irrigation water on the underlying aquifers. Keywords: coalmines, irrigation, gypsiferous mine water.

Jan 1, 2009

By Y. Guglielmi, V. Merrien-Soukatchoff, I. Kadiri

ABSTRACT: Hydraulic experiments have been conducted since 1997 within a small fractured calcareous rock mass in southeastern France, at a site called Coaraze. On this reduced-scale site closing a floodgate located on a downstream spring produces repeated hydraulic loadings. Simultaneous measurements of normal deformations and pressure in several joints have provided a better understanding of the hydromechanical behaviour of such a fractured rock mass. The present paper first describes both the site and conceptual interpretation of the measurements performed. We showed that accurate measurement reproduction requires incorporating certain features: a variable normal joint stiffness, the joint vicinity (through introducing a Z coefficient), and the initial stress state. The paper then develops an original analytical interpretation of the coupled pressure-displacement measurements carried out, which reveal the high level of measurement suitability to the non-linear behaviours examined. 2D modelling, using the discontinuous code (UDEC) was used to proceed with the calibration step. KEY WORDS: In situ test, methodology, hydromechanics, modelling, non linear behaviour ZUSAMMENFASSUNG : Hydromechanische Experimente werden seit 1997 in einer kleinen Kalksteinmasse, das sich im Südosten von Frankreich befindet durchgeführt. In diesem kleinen Standort, werden wiederholte Wasserdruck Erhöhungen durch das Schliessen eines Hahnes produziert. Gleichzeitiger Druck und normale Verformung Meßungen in mehreren Fugen haben erlaubt, das hydromechanische Verhalten einer solche gebrochene Felsenmasse besser zu verstehen. Der Artikel beschreibt zuerst den Standort und stellt die begrifflichen Interpretationen der Meßungen vor. Um die Meßungen gut zu reproduzieren ist es wesentlich, bestimmte Faktoren wie die veränderliche normale Steifheit der Fugen, die Nachbarschaft der Fugen (über einen Z-Koeffizient) und der Spannungstand zu berücksichtigen. Der Artikel erklärt die originale Methode für die Druck- und Verformungs-Meßungen Interpretation und zeigt die gute Korrelation der Meßungen mit dem nicht-linearen angenommen Verhaltens der Fugen. Die numerische 2D-Modellierung mit dem UDEC Software ist für die Verkeilung der Faktoren gebraucht worden. SCHLÜSSELWÖRTER: In-situ-test, Methodologie, Hydromechanik, Numerische Modellierung, nicht-lineares Verhalten RESUME : Des expérimentations hydromécaniques sont conduites depuis 1997 dans un petit massif calcaire fracturé situé dans le sud de la France. Dans ce site de taille réduite des mises en charge répétées sont produites par la fermeture d'une vanne située à l'aval du site. Des mesures simultanées de déformation normale et de pression dans plusieurs joints ont permis de mieux appréhender le comportement d'un tel massif fracturé. L'article décrit dans un premier temps le site et présente les interprétations conceptuelles des mesures. Pour bien reproduire les mesures, Il est essentiel de prendre en compte certains facteurs tels que la raideur normale variable du joint, le voisinage du joint (par l'intermédiaire d'un coefficient Z), l'état de contrainte initial. L'article précise la méthode originale d'interprétation des mesures pression-déplacements qui montre la bonne adéquation aux lois de comportement non linéaire proposées. La modélisation 2D, à l'aide d'un code discontinu (UDEC) a été employée pour le calage des facteurs. MOTS-CLEFS : In-situ, méthodologie, hydromécanique, modélisation, comportement non linéaire

Jan 1, 2003

By A. T. Haile

Detailed monitoring of the response of the rock mass between rockbolt reinforcement units subjected to a simulated seismic source has been successfully conducted. This work has shown the increase in amplification of the Peak Particle Velocity (PPV) with distance from a rock bolt unit, and, a minimum PPV for rockburst damage for the given site characteristics. This understanding, at this site, will allow the design of a suitable rock bolt spacing to prevent unravelling of the rock mass between the rock bolt units for a given level of seismicity. Or, alternatively, an estimation of the requirement for a suitable fabric support system, for the anticipated level of seismicity, can be made.

Jan 1, 2001

By L. Hermansson

Trackless mining at LKAB, Sweden by L HERMANSSON (Visitor) Because the usual means of transporting men and material to the working sites was time-wasting and uneconomical, inclined subways were installed in the Kiirunavaara Mine that permitted the access of rubber-wheeled vehicles to all underground working sites. Men and material could now be transported direct to the working site with no reloading. An increase of 8 to 12 per cent in underground productivity has been obtained by the use of this new transportation system. Rubber-wheeled vehicles are also used in development, production drilling, and loading. In December 1958, the management of the Luossavaara Mine decided to cut the costs of waste-rock haulage. The system of waste transport was the conventional one of shuttle car, rail haulage, and skip hoisting. After consideration of other methods, it was decided to re-equip the mine completely for a system of trackless transport. Results show that mining costs per ton of ore were reduced by 27 per cent, and mining costs per ton of waste were reduced by a spectacular 80 per cent. The new system has proved to be more flexible, and ore grading has been simplified since there is no longer any mixing in ore passes and chutes.

By S. Northey, N. Haque, S. Stoddart, W. Bruckard

Development of new technologies and procedures for managing mineral residues and wastes may benefit from a clear understanding of existing tailing management practices. There is a considerable variability in tailing management techniques used in the Australian copper and gold operations, with associated differences and flow-on effects for the mine site water balance. A database was created, capturing a total of 41 copper and gold processing operations in Australia. The database provides information on tailing generation rates, tailing properties (solids contents and particle size distributions) and tailing storage facility (TSF) types and configurations (e.g. total TSF surface area and wetted surface area). Significant variability was found for the above-mentioned parameters. The solid tailing generation rates ranged from 0.5-37 Mt per annum in 2015. Furthermore, both the solids contents and particle size ranges of the tailing were highly site-specific, and largely dependent on the processing flowsheets. Solids contents of tailings ranged from 45-74% by weight whilst P80 sizes of the concentrator (flotation) feed varied from 75-185 μm. The estimated pumping distance was up to 15 km. The presented data can potentially be used to better tailing management strategies by estimating the potential recoverable water and recycling it, thereby thus reducing tailing footprints. Keywords: Tailing management, tailing storage facility, water balance, mine site, flowsheeting

Jan 1, 2020

By A. Chryss

Tailings management aims to dispose of tailings at the minimum cost consistent with meeting or exceeding imposed standards, including legislative obligations. This simple business objective requires managing the tailings storage facility (TSF) risks associated with surface water, groundwater, dust, sustainable closure, and potential catastrophic failure. The individual nature of every orebody and specific site topography ensures that no one size fits all. It has been suggested that paste and thickened tailings (P&TT) provides the ability to tailor the production and transportation of tailings to suit the deposition site, rather than the traditional approach of accepting that the deposition site has to accommodate tailings of high variability. While the traditional approach can be made to work, it is directly linked to the catastrophic failures of tailings impoundments, where large volumes of decant water have triggered failures due to overtopping, piping or slope instability, or saturated tailings have simply liquefied. P&TT offers an ability to mitigate these risks, and when implemented into new projects with variable tailings streams there are significant benefits to be realized. This paper identifies the interdependencies between the various tailings disposal processes, such as thickening, pumping, and deposition. It demonstrates that there are benefits in taking a more integrated approach to the design and operation of tailings disposal facilities. A collaborative industry project to tackle this challenge is described.

Jan 1, 2012

By A. Koursaris, H. M. Friede, A. A. Hejja

The features of smelting slags from South African prehistoric sites and of related cinder material are described. Chemical analyses of twelve slag samples found in the Transvaal, Swaziland, and Botswana are reported and discussed. An attempt is made to establish a relationship between these slags and the ores collected at the Early Iron Age site of Broederstroom, which date between AD 350 and AD 600. The liquidus temperatures of29 slags were determined by the use oh hot-stage microscope. The major mineral phases of 16 slags were identified by X-ray diffraction and microscopic examination. It appears that the slags investigated were formed at temperatures below 1250°C or - in some cases - at temperatures only marginally in excess of 1250°C.

Jan 1, 1982

By J. -P. Gisiger

On the basis of laboratory test results a comparison of various parameters (unconfined compressive strength, CERCHAR and LCPC abrasivity indexes, mineralogy) is presented and discussed in order to outline certain correlations between them. Samples cover a wide range of lithological types coming from various sites of tunnels. A partir de résultats d’essais de laboratoire, une comparaison de divers paramètres (résistance à la compression simple, indices d’abrasivité CERCHAR et LCPC, minéralogie) est présentée et discutée dans le but d’en tirer certaines corrélations. Les échantillons couvrent un large éventail de types lithologiques provenant de plusieurs sites de tunnels. Basierend auf Laborversuchen, werden verschiedene Gesteinseigenschaften (Druckfestigkeit, CERCHAR und LCPC Abrasionsindexe) präsentiert und Korrelationen aufgezeigt. Die untersuchten Proben verschiedenster Lithologien stammen aus mehreren Tunnelprojekten.

Jan 1, 2003

By S. Z. Pethö, H. Yilmaz

South Deep Mine is currently undertaking numerous voidfilling projects using low strength aerated cement products. Representative samples from one such site, were taken and tested for the load deformation behaviour under uniaxial loading conditions. The process of sample collection, laboratory preparation and testing are explained in detail. The results of testing were analyzed and the critical aspects pointed out as a design consideration to be implemented as part of the quality control and assurance program. Design aspects and underground application of the aerated cement product are discussed for the particular site on 58 level SV1. A simple instrumentation has been designed and installed to enable monitoring of any future movements in this area. A quality control and assurance process has been formulated enabling all aspects of the support installation in this excavation to be signed off.

Jan 1, 2003