Search Documents

By Hamid N. Maleki

Cooperative efforts by the Bureau of Mines and Agapito & Associates, Inc., Grand Junction, CO, achieved the research objective of showing that data from measurements of the rate and change in rate of mine roof movement can be effective in detecting roof instability. Several instruments and techniques have been used to monitor roof movement and to detect imminent roof caves during pillar robbing. Early detection of unstable conditions can provide time either to withdraw personnel and equipment or to allocate supplemental support to prevent injury or down-time. Critical convergence rates were determined both manually and electronically. The detection of critical rate of movement has been shown to be an effective tool in ground control efforts.

Jan 1, 1988

By Allen D. Look, Norman King

For many years, much thought and effort have been devoted to the achievement of safety in the use of explosives by those interested in the preservation of human life and the protection of property. As a result, we now have adequate rules pertaining to the safe use of explosives , which, if observed, would prevent many, perhaps ail , of the explosives accidents that yet occur . Although the rules respecting the use of explosives are believed to be well - known, many accidents occur because they are disregarded . The mental awareness aroused by a tragic accident usually will cause safety precautions to be taken for a while ; however , this awareness gradually disappears unless a sincere effort is made permanently to prevent similar accidents . Frequently, because safe methods are more irksome than unsafe methods , the lessons taught by accident experience are forgotten in a short time , vigilance is relaxed , and there is a gradual return to unsafe , easy methods of performing work. If the preservation of human life is important , the unfortunate experiences of others and the lessons taught by them should be applied to reduce unnecessary loss of life . The value of a life lost as the resuit of accident should be calculated not only from the monetary and humanitarian standpoint but also according to what the accident could contribute in the way of saving other lives and suffering . This saving of other lives can and will , if the lessons from unfortunate accidents are applied , convert a loss to a gain a gain of such magnitude that the accident victim could be considered

May 1, 1944

By T. M. Romslo

"INTRODUCTION This report presents factual data obtained by the Bureau of Mines in the course of an investigation of the Antler mine in the Cedar Valley mining district, Mohave County, Ariz.The Antler property was first examined by Thomas L. Chapman, mining engineer, Bureau of Mines, on December 18, 1943, and January 28, 1944. In June 1945, A. H. Wadsworth, Jr., and R. L. Griggs, geologists, Federal Geo¬logical Survey, examined the Antler mine and several other mines in the district. Both Chapman and Wadsworth recommended diamond drilling of the Antler property to determine the character and extent of ore deposition.In October 1946, the surface and underground workings were surveyed by George Huseman, Mining engineer, and T. M. Romslo, project engineer. The following month Eldred. D. Wilson, geologist of the Arizona Bureau of Mines, assisted by the project engineer, mapped the geology. Subsequently trails were built to drilling sites and diamond drilling started January 16, 1947. The project was completed April 25, 1947.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and takes beneficiation tests."

Mar 1, 1948

By P. S. Haury

"INTRODUCTION Preliminary examinations of the Mohawk zinc prospect were made by John 14. Price and the author in July, August, and September 1943. Considerable quantities of oxidized lead and zinc minerals were found in old shallow work¬ings along two faults - one an over thrust fault with Paleozoic limestone in the hanging wall overlying Cretaceous shale and arkose in the footwall of the fault, and the other a bedding fault in the Paleozoic limestone.The chances appeared good for finding important lead-zinc sulfide ore bodies at 200 to 300 feet beneath the surface, so exploration in three steps by the Bureau was recommended:Surveying, mapping, and character sampling of the outcrops with topographic and geologic mapping of the immediately surrounding area.Preliminary drilling of four test holes, aggregating about 1,500 feet, to locate the top of a possible sulfide ore zone and determine the thickness and intensity of the sulfide mineralization.Contingent upon favorable results of the second step, diamond drilling of about 6,300 feet of additional hole to explore the sulfide ore bodies.The outcrops were surveyed and sampled, a topographic map was made of the area, and the geology was mapped. A project was set up for preliminary drilling of step 2 in the fiscal year 1944-45. An access road to the drill sites was built in April 1945. Diamond drilling was started on April 28 and completed on September 25, 1945, under the supervision or the Bureau of Mines. The exploratory work is covered in this report."

Oct 1, 1946

By E. S. Chalpin

On 25 August 1971, the U.S. Bureau of Mines contracted with the Aerojet Liquid Rocket Company to perform an engineering research program to be completed on 25 May 1972. The program objective was to evaluate the advantages and disadvantages of the underground use of several power sources including but not limited to a closed cycle diesel, electric cable/motor, rechargeable battery/ motor and exhausting diesel for mine shuttle cars, with emphasis on health and safety. This report, Research in Advanced Power Systems for Mining Health and Safety consists of four (4) main parts: (1) Hazards and Safety Analysis of Mine Power Systems, (2) Evaluation of Closed Cycle Diesel Power System for Mine Applications, (3) Closed Cycle Diesel Power System Consumables Compatibility, and (4) Concluding Remarks and Recommendations. The hazards introduced to a mine by shuttle car power system failure modes were evaluated and reported. A "fault tree" analysis was generated for each power system and the probability of death or injury during an eight (8) hour shift and for a week of operation (105 hours) were estimated. Advantages and disadvantages were also reported for each system studied. Aerojet's assessment, based on a "forced decisions analysis," of the four shuttle car power systems as to their relative health and safety is that the exhausting or open cycle diesel is preferred, followed by the closed cycle diesel, the electric cable/motor and the rechargeable battery/motor. The assessment was based on ten parameters pertinent to the health and safety aspects of shuttle cars. Drawing layouts of two typical mine shuttle cars incorporating closed cycle diesel powerplant concepts are included in this report. The performance parameters established for the two concepts are tabulated. A study was made of the logistics involved in transporting and replenishing the consumables needed to operate a shuttle car equipped with a closed cycle diesel. The closed cycle diesel powerplant consumables -oxygen, potassium hydroxide, and diesel fuel - were analyzed as to their compatibility with materials found normally in a gassy coal mine. Spill tests simulating inadvertent leakage of liquid oxygen in a coal mine were performed. A critical evaluation of existing oxygen sensitivity data and the relationship to the use of oxygen on a shuttle car in a coal mine environment is presented.

Jan 1, 1972

By Oliver Bowles

"Asbestos" is a name applied to a group of naturally fibrous minerals. Because it has the fibrous characteristics of silk or cotton and at the same time will not burn and has other advantageous properties as well, asbestos has specialized uses for which no adequate substitutes are yet available. Asbestos furnishes a major raw material for a great variety of essential products, the manufacture of which constitutes a vast industry. Asbestos generally occurs in irregular veins scattered throughout rock masses. Most of the fiber-bearing rock is mined in huge open-pit or underground workings. The fibers are separated from the rock and sorted into groups, according to length, in large, complex mills. The longer fibers are stripped to textile plants, where they are further fiberized and prepared in special machines and are used for spinning into yarn and weaving into unburnable cloth that has many important uses. The shorter fibers, which are much more abundant than the long ones, are used in asbestos-cement building materials in heat-insulating products and for a multitude of other applications. These processes and uses are covered in considerable detail in later sections of this report.

Jan 1, 1959

By Steven W. Schmauch

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines Studied 25,340 acres of the 28,960-acre Twelve Mile Creek Wilderness Study Area (OR-003-162) in order to evaluate its identified mineral resources. The study area is located in Malheur County, OR, about 30 miles northwest of McDermitt, NV. The area is underlain by thick sequences of rhyolite to with lesser amounts of andesite and basalt flows. Bureau of Mines personnel reviewed pertinent literature, mining records, and examined the study area for possible mineral resources in geologically favorable sites. There are no organized mining districts and no record of past or current mining activity. Based on sample results, published literature and field observations, there are no identified mineral resources.

Jan 1, 1987

By Fun-Den Wang

This report presents the results of two large scale field coal pillar strength tests (80 ft by 80 ft), the results of a series of laboratory small core sample tests, and the correlation between those field and laboratory tests. The concept of applying laboratory coal sample strength data to predict the in situ coal pillar strength appears to be feasible. The deformation property of large pillars can be obtained successfully by testing the coal sample in the laboratory within acceptable accuracy. There are prevailing directional strength and deformation properties in coal pillars along the butt and face cleat system.

Jan 1, 1976

By Lawrence W. Scott

This report presents several systems for continuously monitoring the quality of air in underground mines that are being developed by the Bureau of Mines. Underground stations measure methane, carbon monoxide and nitrogen dioxide concentrations, air velocity, and air temperature. This information is transmitted over a single telephone pair to central stations located on the surface. The central stations display alarms and the data is selectably displayed on digital panel meters.

Jan 1, 1977

By R. Karl Zipf

A fatal explosion in a sealed area at the Sago Mine in 2006 prompted researchers and regulators in the United States to re-examine the requirements for explosion-resistant mine seals. Seals are used in underground coal mines to isolate abandoned mining areas from active workings. Prior to the Sago disaster, mining regulations required seals to withstand a 140 kPa explosion pressure. Recent research at the National Institute for Occupational Safety and Health (NIOSH)Pittsburgh Research Laboratory showed that pressures from explosions can far exceed this pressure. U.S. mining regulations now require much stronger seals. Current research focuses on understanding the science, engineering and management of sealed areas of coal mines. Scientific efforts seek understanding of how explosive methane-air mixtures accumulate using measurements and models of the sealed area atmosphere. Additional scientific efforts aim to understand the explosion pressures that can develop using a combination of numerical modeling and experiments. Engineering efforts aim to produce design guidelines for seals that can resist the new higher pressure design criteria. NIOSH researchers are also developing guidance for monitoring of sealed area atmospheres and inertization of potentially explosive gas mixtures within sealed areas. This paper seeks to encourage scientific discussion among international peers since preventing explosions within sealed areas is of interest to underground coal operators and regulators.

Jan 1, 2009

By Carl F. Wingquist

Electrical resistance heating to effect thermal fragmentation of semiconductive rock was examined by the Bureau of Mines. Tests were carried out on copper-bearing ores of the Nonesuch Shale Formation in the laboratory and in the the field at White Pine, Mich. Fieldwork included primary and secondary breakage tests. Heating tests on in situ rock failed to produce thermal dam-age to an extent considered useful; however, boulders up to 30 ft3 were effectively broken by the method. Power input to the test rock was taken from a 50-kV, 5-amp dc power supply.

Jan 1, 1976

It is a pleasure to submit to the National Critical Materials Council (Council) some of my thoughts concerning the important tasks which lie before you. It long has been my belief that America's economic health and national security may depend to a substantial degree on whether we have available to us an adequate supply of critical and strategic materials at reasonable cost. To the extent the Council can contribute to the identification and implementation of wise public policies which facilitate the achievement of that goal, we and our children should be grateful. Even before assuming office, President Reagan warned of the danger of undue dependence on imported materials essential to the Nation's defense and economic well-being. After his election, he appointed a transition task force on strategic and critical materials, and he later directed the Cabinet Council on Natural Resources and Environment to prepare .a National Materials and Minerals Program Plan and Report to Congress, which he forwarded to the Congress in April 1982. In 1984, my predecessor, Secretary Clark, established the National Strategic Materials and Minerals Program Advisory Committee, popularly known as the "Mott Committee" because of its distinguished chairman, retired Admiral William C. Mott.

Jan 1, 1986

By Keith L. Harris

Recent data indicate a marginal decline in overall growth in world economic output from 3.1% in 1985 to 2.9% in 1986 (table 1),2, 3 Many nations experienced slower economic growth because of the huge trade imbalances existing between the United [ ] States and Japan and the Federal Republic of Germany, the U.S. budget deficit, and the growing Third World debt. Some developing nations, however, experienced booming growth. Declining prices for energy and nonenergy commodities and the fall of the dollar against the currencies of major industrial countries benefited several developing countries--energy importers and exporters of manufactured goods with currencies tied to the U.S. dollar, which were able to expand markets in the industrialized nations. The drop in commodity prices increased demand in industrial countries and depressed it in developing countries. Lower demand in the developing countries contributed to a decline in the real net exports from industrial countries. As a result, output growth in industrial countries declined from 3.0% in 1985 to 2.4% in 1986, despite growing internal demand, Average output growth of developing countries increased from 3.296 to 3.596 during the same period, however, primarily because of the low prices of their products and the strength of demand in industrial countries for those products. Developed country output growth was extremely uneven, however. For example, the economic output of nonfuel exporters grew 5.4% in 1986, while that of fuel exporters dropped 0.7%.

Jan 1, 1987

Chromium, a critical mineral for which the United States is largely dependent on foreign sources, is the subject of a new report just issued by the Interior Department's Bureau of Mines. The report is the first in a new series called "Mineral Commodity Profiles" (MCP's). Designed to give an updated review of important events affecting critical minerals, it also presents a comprehensive description of industry structure, supply-demand relationships, technology, and outlook for the future.

Jan 1, 1977

By Keith L. Harris

The performance of the world economy improved significantly in 1984. Real world output!/ grew 4.3% (compared with 2.6% in 19831, the highest since the 4.4% increase recorded in 1978 (table 1). The output of industrial nations rose 4.9%, while that of the developing nations rose 3.7%. The United States and Japan had the largest increases in output of the major industrial nations, with respective increases of 6.8% and 5.8% (table 2). The components of real output with the most significant growth in the industrial countries were gross fixed investment (9.2%), consumer expenditure (3.1%), and public consumption (2.5%) (table 1). Industrial output, as measured by industrial production indices, has returned to about the 1980 level for most of the major industrial nations (table 2). Exceptions to this were industrial production in Japan and the United States; Japan's industrial production rose steadily throughout the 5-yr period and is now more than 16% above the 1980 level, and the industrial production index for the United States reached 11 1.2 (1980=100.0). Real total domestic demand grew at 8.7% in the United States, more than double the rate of Japan, which, at 4.0%, had the second-largest growth. Average demand for all industrial countries was up 5.1%. During 1984 the U.S. dollar showed great strength on international markets, contributing to large current-dollar negative net exports of goods and services and even larger negative net exports of the merchandise sector. While growing U.S. imports helped spread the benefits of the recovery, they also led to a widening of current account imbalances and growing trade tensions throughout the world.3/, 4/

Jan 1, 1985

Several primary ingot producers have introduced price changes for July. Howmet Aluminum Corp., Revere Copper and Brass, Inc. and the Anaconda Co, will increase late-July prices of 99.5 percent unalloyed aluminum ingot by 3 cents to 56 cents per pound, Prior to this, Kaiser Aluminum and Chemical Corp. had advanced June ingot values by 4 cents to 57 cents and Consolidated Aluminum Corp., 4.5 cents to 57.5 cents. Domestic merchants held June quotes at a range nearing 50-50.8 cents per pound. ANTIMONY Although NL Industries, since April of this year, stopped publishing prices for RMM and Lone Star antimony grade, values of domestically-refined antimony in alloy are being made available to industry, The current price of this material is $1.75 per pound of antimony contained in alloy, New York dealer-marketed metal was available in June at $1 -13-$1 .20 per pound. Important industrial uses of antimony are for flame retardants, storage batteries, chemicals, pigments, rubber, plastics, glass, ceramics and machinery.

Jan 1, 1978

By Ivor Hawkes

The purpose of the development described in this report and as stated in the contract work statement is to "design, develop, fabricate, test and demonstrate, and deliver to the government permissible low cost cylindrical stress gauges and associated components capable of measuring change of stress as a function of time in underground coal mines. The cylindrical stress gauges shall be suitable for installation in bore holes". The technique adopted for measuring rock stress changes is to preload a steel cylinder diametrically across the sides of a 1-1/2 in diameter bore hole and detect deformation of the cylinder from stress changes in the rock, by means of a vibrating wire transducer. By calibration, changes in the period (time for one wire oscillation at the natural frequency) of a high tensioned wire stretched diametrically across the cylinder in the direction of load application are related to stress changes in the rock. To completely evaluate the stress field change in the plane of the bore hole, three gauges set at an angle to each other are required.

Jan 1, 1973

By H. D. Kline

This publication describes methods and techniques of mining and crushing limestone at 3 of 11 small quarries operated by Anderson-Oxandale Rock Co. in northeast Kansas in 1959. It is one of a series of reports by the Bureau of Mines on methods and costs of mining in various mining districts in the United States. The three quarries selected for study -Bosse quarry, Pottawatomie County; Hansen quarry, Morris County; and Huston quarry, Dickinson County (fig. 1) -were in many respects similar to many others that had been developed solely to fill local and usually transitory demands for crushed limestone for use as concrete aggregate, roadstone, and soil conditioning. Factors governing the choice of quarry sites were quality of limestone, shallow overburden, and proximity to points of consumption of the crushed stone.

Jan 1, 1962

By John J. Mulligan

The Bureau of Mines investigated the tin deposits of the Cape Mountain area during July and August 1962 to test the effectiveness of detrital-cover sampling in permafrost areas as a relatively cheap and simple means of guiding mine development and exploration. Results indicate that systematic detrita1-cover sampling can be used effectively to delineate obscure deposits with sufficient accuracy to permit sampling with a minimum of trenching or drilling. Extensions of known outcroppings were traced in sufficient detail to guide lode sampling and several previously unknown tin-bearing lodes were found and sampled. Lode sampling was limited to the minimum needed to establish the reliability of detrital-cover sampling results. The results of previous lode and placer investigations are summarized and detrital-cover sampling methods and results are described in detail.

Jan 1, 1966

By Charles J. Cohen, Donald F. Reed

"INTRODUCTION AND ACKNOWLEDGMENTSThis report supplements a previous report on work done in this same area 4/ but covers only the period from November 1945 to November 1946. The project was established in 1943 to investigate magnetite deposits in the northwestern Adirondacks by geophysical surveying and diamond-drilling for the purpose of increasing iron production in the eastern United States.In its program of investigation of mineral deposits, the primary objective of the Bureau of Mines is the more effective utilization of our mineral resources, that they may make the greatest possible contribution to our national security and economy. The policy of the Bureau is to publish the facts developed by each project as soon as possible after its conclusion. Maps showing the detailed magnetic surveys of the deposits and anomalies discussed in this report are on open file at the offices of the Bureau of Mines, College Park, Md., and at the University of the State of New York in the office of the Director of the State Science Service, Educational Building, Albany, N. Y.The Mining Branch, Lowell B. Moon, chief, conducts preliminary exami¬nations, performs the actual investigations, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.The chemical analyses included in this report were made at the Eastern Experiment Station of the Bureau of Mines at College Park, Md., under, the general supervision of J. B. Zadra, chief, College Park Division, Metallurgical Branch, and the immediate direction of Dr. Alton Gabriel, in charge of the laboratory service unit."

Nov 1, 1947