Search Documents

By Roger G. Long

In May 1973, the Bureau of Mines asked Arthur D. Little, Inc. (A DL) to investigate existing industrial communication standards that may be applicable to the problem of developing standards for mine communication, considering that the standards that may ultimately be developed will require simple field procedures for the industry and the inspectorate to determine that communication systems are properly functioning. The emphasis on this study is on telephone communications as related to coal mine applications. B. TASKS The tasks agreed upon for this program were as follows: 1. "Investigate the current practices and existing standards of other industries under government regulation. 2. Determine applicable methods for industry personnel and inspectors to ascertain conformance on-site with minimal test hardware. 3. Review the Bureau's approval, testing and inspection procedure as it may impact the development of such standards. 4. From the above studies investigate the development of installation and performance standards for mine communications, including voice and telemetry. 5. Prepare a written report specifying what standards and field inspection techniques are applicable with recommendations for development of subsequent data and ultimately standards and field inspection techniques. 6. Prepare a written summary of the findings of various investigations with an appendix covering the detailed findings of each investigation. 7. Prepare a list of suggestions of additional assistance the Bureau might require in subsequent phases of developing communication standards and means of ascertaining performance."

Jan 1, 1973

To improve the level of hearing protection by providing workers with an inexpensive, easy-to-use device to check earplug fit. Background Approximately 30 million workers are exposed to hazardous noise on the job, placing them at risk of permanent hearing loss, tinnitus, and other disorders. Although the preferred solution is to eliminate noise through engineering controls or to reduce noise exposure through administrative controls, hearing protectors are critical when noise is unavoidable. Studies of hearing protector users have shown that average protection values in the real world are much lower than the labeled noise reduction ratings determined in laboratories with trained and motivated subjects. Even worse, many hearing pro­tector users get virtually no protection at all because of poor fit. The studies also show that users have a harder time achieving adequate protection levels with earplugs than with earmuffs. It?s difficult for users to tell if earplugs are working well just by looking at them. A more accurate approach is to check how much they block or ?attenuate? noise. Earplugs vary in their attenuation characteristics, with most providing a maximum of 20?35 decibels of noise reduction when worn correctly. Any earplug that?s suitable for use in noisy settings will attenuate noise by at least 15 decibels. Personal fit testing is an effective way to help hearing protector users improve the fit and protection levels of the devices. However, existing fit-testing systems are expensive and unsuitable for use at many industrial worksites.

Dec 1, 2008

The Bureau of Mines studied available information on the nature and occurrence of potential sources of aluminum in the United States, its Pacific island possessions, and Puerto Rico to obtain data for use in evaluating the production capability and costs of extracting the aluminum from such materials. The quantity, type, and grade of the materials range from 4 billion tons of bauxite, bauxitic clay, and kaolin averaging 33 to 42 percent Al2O3 to nearly 600 billion tons of anorthosite containing only 27 percent Al2O3. Principal deposits of bauxite, bauxitic clay, and kaolin occur in Arkansas, Georgia, Hawaii, and Oregon. Major anorthosite deposits are located in New York, Wyoming, California, Idaho, and Montana. About 11 billion tons of material in deposits of various types of clay, the kyanite group of minerals, laterites, and shales averaging 27 to 30 percent Al2O3 comprise additional resource's from which aluminum some day may be extracted. Material meeting specifications of the study was found in only 22 States and the Pacific island possessions. Utilization of these large low-grade sources of aluminum awaits development of processes that are economically competitive with the Bayer process for extracting alumina from baxuite, which is at present the only commercial ore of aluminum. Changes in economic and political conditions also may play important roles in the eventual development of the potential sources of aluminum.

Jan 1, 1967

By J. W. Thompson

SALE AND CONVEYANCE. DEED BY INDIAN ALLOTTEE OF UNSOUND MIND-BONA FIDE PURCHASER. The deed of an Indian allottee whose mind was unsound, but who was not entirely without understanding, is voidable if made before the grantor's incapacity has been judicially determined; and a purchaser of the original grantee who interposes the defense of a bona fide purchaser has the burden of showing a purchase for value and on failure to do so can not claim the benefit of a bona fide purchaser. Adams Oil & Gas Co. v. Hudson (Oklahoma), 155 Pacific, 220, February. 1916. PURCHASER OF MINING CLAIM-RIGHT TO FIXTURES. The purchaser of a mine equipped with an electric hoist, placed in the mine under a rental contract with the owner of the hoist and under an agreement to return it to the owner at the expiration of the term of hiring, can not claim and hold the hoist as against the owner where the agent of the seller explained to the purchaser that the hoist was not owned by the owner of the claim. Montana Electric Co. v. Northern Valley Mining Co. (Montana), 153 Pacific, 1017. p, 1018, October, 1915. AUTHORITY OF GRANTEE TO EXTEND LEASE. A deed conveying lands subject to an oil and gas lease under which the lessee had the right to drill or pay money in lieu of drilling at his option, and reserving to the grantor a share of the royalties under such lease, and expressly authorizing the grantee to lease the land for oil and gas purposes and to take the rentals, authorizes the grantee to extend the existing lease before the expiration thereof in consideration of the annual payment of money in lieu of drilling, as contemplated by the lease.

Jan 1, 1916

By Henry P. Cole

A series of studies are described that identify critical health and safety skills needed by underground coal miners for coping with mine emergencies. First aid and self-rescue and escape were selected as two broad performance domains that include many subordinate skills needed for preventing, recognizing, and coping with mine emergencies. The performance domains and their objectives were used to direct the development of simulation exercises that permit miners to experience mine emergencies in the safety of a training room. The exercises are based upon research with similar simulations for the training of flight crews and medical personnel in information gathering, judgment, and decision making skills. Exercise content is drawn from actual mine accident and disaster case studies. The exercises incorporate recent principles of cognitive psychology and instructional design. Initial studies in annual refresher training classes suggest the exercises are stimulating for miners and their instructors, easy to use and read, sufficiently complex and authentic to challenge experienced miners, and useful devices for both teaching and testing critical problem solving skills required for preventing and minimizing emergencies.

Jan 1, 1988

By J. H. Crary

This report summarizes the results of a one-year agreement for research on the electromagnetic environment in coal mines, which was conceived as the beginning of a long term cooperative program between ITS and the Bureau of Mines. The concepts on which it was originally based are a result of the report on mine rescue and survival by the Committee on Mine Rescue and Survival Techniques of the National Academy of Engineering, dated March 1970. This report drew particular attention to the need for improved communications during and following mine disasters. In particular, the outstanding problems identified were the location of, and communication with, trapped miners. Some tentative solutions, generally involving long-wave electromagnetic signals, were offered. Consideration of the problems of disaster location and communication soon leads to consideration of the communications techniques (or lack of them) for use under normal mining conditions. In particular, if a disaster communication and/or location system is to be readily available and operable under disaster conditions, it should also be usable during mining operations. In this way operators can become familiar enough with the system to operate it during disaster conditions, as well as provide a mechanism for regular testing.

Jan 1, 1972

By Leroy E. Schulze

A review of development and a reevaluation of uses of the hydraulic air compressor are suggested by the constant changes in technology, which frequently make an old art valuable in solving current problems. Contacts with research workers in various branches of engineering indicate that this older method of producing compressed air may not be familiar to some or that its salient features might be useful in solving problems involving uses of compressed air. Briefly, a hydraulic air compressor may be described as an inverted siphon, consisting of an intake head where water and air are mingled, followed by a gravity-fall tube in which air is intimately mixed with the water and is compressed as the water pressure increases during the fall down the tube, then a separating, or stilling, chamber in which air bubbles rise to the surface of the water and collect in the upper portion of the chamber at a pressure equal to the weterhead maintained by the height of water in the discharge leg of the circuit. The water, which now contains only the fraction of air that has gone into solution, passes out of the separating chamber and rises up the discharge leg to the surface, which is, of course, at some suitable distance below the level of the intake. Present-day applications include (1) utilizing low hydraulic heads, which otherwise have little commercial values; (2) utilizing low hydraulic heads in reclamation work to supply compressed air, or in some instances to produce a small suction, for air-lift pumping (or for operation of air motors), with minimum attendance and without need for electric power; (3) utilizing medium heads, as at dam and lock installations, to produce compressed air for pneumatic operation of airlifts, gates, valves, and rubber gate seals; (4) utilizing underground waters, as in mines, to produce compressed air for general mine use; (5) using this method of isothermal compression of air in combination with standard compressors wherever hydraulic head is available, thereby securing the advantages of low-temperature intake to the mechanical compressors and reduction of moisture content below that of atmospheric air; (6) development of large air supply at pressures up to 150 p.s.i.g., which, after performing work in reciprocating or centrifugal expansion cylinders, is available at temperatures approximating -50° F. Possibilities in freezing and reheating should be mentioned which may prove economical for obtaining uniformly dry air for process work, wind-tunnel tests, or large air-conditioning installations, such as ventilation of underwater traffic tunnels, and may be economic for supply of supercharged air to gas-turbine plants.

Jan 1, 1954

By Edward E. Johnson

The principal purpose of this study was the development of an engineering and economic model of a hypothetical large-scale open pit gold mining operation. The guiding concept in developing the model was the idea that, through study of a number of such models, it would be possible to evaluate a mineral property and to make reasonable estimates of the benefits to be derived from research in mining and metallurgy. The model by use of a computer is able to produce results easily and quickly when cost factors are varied. Cost factors may be varied as a result of assumptions of improved technology or of assumptions of assuming different approaches or methods to accomplish a particular segment of the mining or processing operation. The discounted cash flow rate of return was used to measure the effect of changes in costs or expected revenue. In this study, assumptions based on past processing practices were made in an effort to reduce costs of processing the ore These assumptions were: (1) Eliminating the low-grade cyanide circuit; (2) reducing the quantity of material to be processed by screening after crushing; and (3) using a combination of assumptions (1) and (2). All three assumptions resulted in reduced capital investment and operating cost that caused substantial increases in the rate of return.

Jan 1, 1968

By J. Dean Warner

In 1984 and 1985, as part of its critical and strategic minerals studies, the Bureau of Mines investigated lode and placer tin occurrences near Rocky Mountain (Lime Peak), in east-central Alaska. The lode occurrences consist of mineralogically complex, generally fault-controlled veins, and contain an average of approximately 0.05 pct Sn, as cassiterite. Beneficiation testing of two bulk samples of the vein material produced concentrates containing 65 and 59 pct of the total tin values at grades of 0.35 and 13.9 pct, respectively. Although as much as 30 million short tons (MMst) of mineralized rock containing up to 20 MMlb Sn may be present, the grade of these occurrences is too low to be considered economic at this time. Trace amounts of cassiterite were also identified in surface samples of glacial out-wash gravels collected along North Fork Preacher Creek, which partially drains the area of tin lode deposits near Lime Peak. Low tin grades in the samples do not account for the former erosion of a large volume of lode tin mineralization from near Lime Peak; higher tin grades may be present in gravels closer to bedrock.

Jan 1, 1988

This publication summarizes, for potential contractors and all other interested parties, the research and development of in-house and contract projects programmed by the Bureau of Mines for fiscal year 1983 (October 1, 1982-September 30, 1983) under its Health and Safety Technology program. The objective of these projects is to provide an ordered and sequenced series of advance toward the Bureau's overall goal of providing the systems technology required to create a more healthful and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1982

By Dennis R. Dolinar

The National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory conducted a full-scale test of a composite polyurethane-aggregate seal in a hydrostatic chamber at the Lake Lynn Experimental Mine. This composite seal consisted of a polyurethane and limestone aggregate core that was formed between two concrete block walls. In the hydro-static chamber test, water is used to pressurize the seal. During the test, the maximum average water pressure the seal was able to withstand was 18.9 psi. Further, the seal began to yield at an average water pressure of only 17 psi. At the time of the test, the minimum seal design requirement was 20 psi under 30 CFR4 75.335 (2005). Therefore, based on this test, the seal did not meet the regulatory minimum design requirement. Uniaxial compressive tests conducted on samples from the polyurethane-aggregate core revealed that both the compressive strength and the elastic modulus of the material were much less than that for polyurethane only with a density of 10.0?12.0 lb/ft3. The significant reduction in the strength and stiffness of the polyurethane-aggregate mixture results from the formation of a soft polyurethane foam around each piece of aggregate. The formation of the soft foam seems to be caused by residual moisture from the aggregate. The moisture also caused the density of the polyurethane in the polyurethane-aggregate mixture to be less than the design requirements. The lower density of the polyurethane in the mixture, along with the formation of zones of pure polyurethane only, resulted in the overall seal density being less than the design requirements. During seal construction, steps were taken to control the moisture, but were not successful. An analysis of the seal failure showed that the calculated shear stresses at failure and the estimated shear strength of the polyurethane-aggregate mixture are fairly close. This suggests that the strength properties of the polyurethane-aggregate mixture along with a weak zone of poorly bonded aggregate controlled the maximum pressure the seal could withstand. At the time of the seal testing, the minimum design requirement was 20 psi, as specified at 30 CFR 75.335 (2005). New emergency temporary standards for seal designs were promulgated on May 22, 2007, with a minimum requirement of 50 psi under specified conditions. However, it will be shown that the evaluation of the polyurethane seal performance as designed to meet the older 20-psi criterion can be relevant to the design requirements under the new standards.

Jan 1, 2008

By Lloyd Williams

A vertical air shaft in the Birmingham, Ala., iron district was sunk with a circular cross section and lined with concrete at a relatively low cost to provide needed ventilation for an iron-ore mine. The method of sinking the shaft is described, and the costs are stated in mar-hours with a descriptive list of equipment and a statement on the size and use of temporary buildings. Preparation began May 2, 1955, and the shaft was completed at a depth of [680] feet by September 22, 1956. By October 1956, all temporary building and [aft]-sinking equipment had been removed. The total direct-labor cost for the operation, including preparation and dismantling, was 50,700 man-hours, or 30.2 man-hours per foot. Total rock and dirt removed amounted to 17,523 cubic yards (in place), and the shaft lining required 4,635 cubic yards of concrete to form a circular air shaft with an inside diameter of 16 feet.

Jan 1, 1960

By D. D. Hamilton

The ISMS program provided for the development and demonstration of equipment modifications for improved safety in both conventional and continuous coal mining systems. This report documents the success of the program in identifying accident hazards in underground coal mines with 4-to 8-foot seam heights, in designing modifications to reduce the hazards, and in demonstrating improved safety through extended underground use of the ISMS equipment.

Jan 1, 1977

The purpose of Volume II of this study is to provide a general plan for the pilot testing of two materials which could be used to tag explosives for both pre- and postdetonation identification and of tracing techniques which would thereby aid the investigator of an unauthorized bombing or explosion in being able to determine the source and/or user of the explosives. Volume I described the planning factors by which the tagging of explosives could be implemented on a National basis. 1.2 BACKGROUND Tagging explosives at the time of manufacture with a taggant material that could survive detonation, be recovered, and provide an investigative lead has been seriously studied for several years. This concept has gained widespread support among many law enforcement groups because of the scant clues that can presently be found among bombing residue.

Jan 1, 1977

By Michael J. Friedel

The permeability and flow capacity in unsaturated media are investigated by the U.S. Bureau of Mines for application to in situ copper leach mining. Moisture retention properties are derived and combined with scanning electron microprobe data to characterize the mineralogy, texture, pore size, distribution, and permeability of the host rock. Finite-element modeling is used to derive a saturated permeability, ambient degree of saturation, and assess various injection-recovery schemes. Recommended design modifications for optimization of solution distribution and maximum recovery from the rock matrix requires either (1) the injection pressures on the order of 1,500 psi and recovery wells operating in a suction mode, or (2) performing permeability enhancement, through in situ rubbling. Injection pressures can be reduced to 500 psi with improved recovery and containment of solutions.

Jan 1, 2010

By Edward E. Tate

This is a report on the design, development, and manufacture of a prototype roof bolting machine for high rise applications. The machine is designed to traverse a 32 inch entry and rebolt a roof fall area to a height of 28 feet 10 inches. Covered in the report is a chronology of the project, an explanation of the design problems, and a description of their solutions. The report concludes that the equipment as designed is suitable for the purpose intended and further testing is recommended.

Jan 1, 1981

By Israel Liebman

The Bureau of Mines developed three types of passive water barriers for suppressing slow-moving coal dust explosions. One type is a modification of a conventional tub barrier and depends on the dynamic pressure generated ahead of an explosion to tilt the tub to release its water and suppress the explosion. The other two barriers operate in response to an increase in static pressure developed ahead of the explosion. Tests indicate the first barrier begins to release its water at air speeds as low as 50 ft/sec, and the second and third barriers will operate at a rise in static pressure as little as 0.5 psi. All three barriers were found to be effective in suppressing coal dust explosions propagating at speeds as low as 100 ft/sec. A plan is described for installing a water barrier in a working mine on a trial basis.

Jan 1, 1976

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 12,564-acre portion of the 34,795-acre Rockhouse Wilderness Study Area (CA-010-029) in order to evaluate its identified mineral resources. The study area is located in Kern and Tulare Counties, CA, about 60 air mi northeast of Bakersfield at the south end of the Sierra Nevada. A review of the geologic and mining literature, and a field examination identified a turquoise and a gold prospect in the study area, and another gold prospect and a feldspar prospect within a mile of the study area boundary. Thirty-three rock and 16 alluvial samples were taken.

Jan 1, 1988

By Katherine A. Klein

Refuge chambers may potentially save the lives of miners during a mine emergency. For this reason, it is crucial that miners know how to operate them. Unfortunately, because refuge chambers provide so many services, they can be very complicated and difficult to operate. Therefore, NIOSH has created this document with suggestions for developing manuals and educational materials. A multidisciplinary team comprised of NIOSH engineers, sociologists, psychologists, health communication professionals, and geologists developed the recommendations contained in this document. These recommendations are based on an evaluation of manufacturers? instruction manuals from both the U.S. and globally, interviews with over 20 mining and safety experts, and an extensive literature review. This research, focused on the best practices for refuge chambers, led to the formulation of this document. It is intended to offer suggestions to manufacturers and mine operators on how to create effective and easy-to-understand training manuals for miners as well as tips to create the most comfortable and usable refuge chambers. It should be noted that these recommendations are not meant to substitute for manufacturer-supplied materials but rather to be used in conjunction with manufacturer?s materials. Manufacturers should always be consulted for up-to-date information about their chamber. Although different states and different mines refer to underground refuges by different names, this guide will simply refer to underground refuges nearest to the face as refuge chambers, whether inflatable from a skid or constructed from steel. Other popular terms for refuge chambers are rescue chambers, rescue shelters, and refuge shelters. Refuges that are nearer to the shaft, whether a prefabricated refuge chamber or one built into a crosscut, will be referred to as outby refuges because of their location in the mine. Outby refuges can be permanent, semipermanent, or portable and are usually located at every other SCSR cache. Outby refuges are sometimes called hardened rooms, outby shelters, and in-place shelters. When discussing outby refuges and refuge chambers collectively, this guide will refer to them as underground refuges. Other terms for underground refuges include refuge alternatives, locations of safety, and safe havens. This document is designed to be read either cover to cover or by specific section. It is recommended that on first read, this guide be read cover to cover. In subsequent readings, manufacturers and mine operators may find it easier to use the table of contents page to locate specific information on parts of the refuge chamber.

Jan 1, 2009

By Walter W. Kaufman

The braking performance of underground, rubber-tired, coal mining vehicles is evaluated. Surveys of mining equipment and braking manufacturers and underground stopping tests are discussed as they relate to this evaluation. Stopping performance recommendations are proposed.

Jan 1, 1977