Search Documents

By Maurice Deul

This bulletin summarizes the work conducted under the Bureau of Mines methane control research program during the years 1964 to 1979. This research effort was directed toward improving existing methods and developing alternative methods of reducing the explosion hazard during mining. The research was performed in three general areas: (1) basic factors that control the emission of methane into coal mines, (2) methane control during mining, and (3) methane drainage in advance of mining. Topics discussed in this bulletin include the magnitude of the methane problem; the equipment and instruments developed; the geological, chemical and physical parameters that control the movement of methane in coalbeds; the direct method of determining gas content; the estimates of gas content from adsorption data; and methane drainage, through shafts, through horizontal boreholes, through vertical boreholes, or through slant holes. Improvements in ventilation, control of methane in gob areas, and water infusion are also discussed, as is the potential use of coalbed methane as a supplement to natural gas supplies. This bulletin provides a comprehensive source of information on the accomplishments of the Bureau's methane control research program, on the technology developed, and on the direction of further research.

Jan 1, 1986

The Kaiser Aluminum and Chemical Corp. announced plans to raise June ingot prices by 4 cents to 57 cents per pound. Producers? April value for 99.5 percent unalloyed aluminum ingot was at 53 cents per pound. Domestic merchants last month were quoting the metal at 48-49 cents per pound. Primary aluminum producers began restarting production facilities following the settlement of the coal strike. Noranda Aluminum Inc. recalled workers to prepare potlines for production at its plant at New Madrid, Mo., which had closed February 14, 1978 due to the shortage of coal. Eastalco Aluminum Co. resumed full capacity production at its Frederick, Md. smelter where production had been cut by 30 percent. Anaconda Aluminum Co. resumed full capacity production at its Sebree, Ky. smelter.

Jan 1, 1978

By D. W. Dareing

Multiple branch wellbores and horizontal holes, when applied to deep lying ore bodies, have the potential of significantly reducing well costs by reducing total footage drilled per acre of well pattern. In addition, horizontal holes may increase sweep efficiency. Well completion is a major problem. They must be cased to contain leaching solutions within the underground portion of the production loop. Several drilling and completion concepts are given and evaluated in the report. Our evaluation shows that there is economic incentive to further develop these concepts for field application to ore bodies 1,500 feet. Multiple branch concepts are the most attractive. They can reduce well costs by as much as 30° when applied to 2,000 feet ore body depths (44%, at 5,000 feet) and can accommodate a lamer pump than conventional vertical wells. We recommend this concept be developed further to accommodate either dual or triple branches.

Jan 1, 1980

By Charles H. Rich

This Bureau of Mines report is an expansion and update of Information Circular 8719 and comprises maps and tables listing the name, location, and other pertinent data concerning certain fuel-related projects. The maps show the locations of the planned or proposed facilities. The tables include information on projects involving the proposed or planned development of fuel resources, as well as the development of storage, transportation, and conversion facilities. The report covers the 24 States west of the Mississippi River including Alaska and Hawaii. Of the 808 projects for which information is provided, 219 concern coal mines, 246 concern electric generating plants, and 115 concern uranium mines; Energy Supply and Environmental Coordination Act coal conversion notices are also included. Because of the dynamic nature of the energy industry, many uncertainties exist and some of the listed projects may never become realities. Also, no attempt has been made to determine the degree of certainty or viability of each project.

Jan 1, 1978

By Roy Greenfield

Estimates are given for the distance from a seismometer at which a miner can probably be detected. The procedure in making these estimates was to first establish the natural noise levels at the output of a surface seismometer for the 25 to 100 Hz frequency passband. The noise levels give the range of values which may be expected in areas with no man-made noise. For each noise level, we give the detection threshold which, when exceeded, indicates that a signal has been received. Based on the signals recorded by Westinghouse, curves are given which show the peak signal amplitude as a function of source- to-receiver distance (slant range). Curves are given for the Westinghouse seismic thumper, a 50-pound timber, and a sledge. For a given type of source, the receive signal strength depends more strongly on slant range than on any other factor. However, there is approximately a five-to-one scatter in the amplitudes. Thus, further study of factors affecting the signal amplitude might allow better estimates to be made for any particular geological setting. Combining the signal amplitude with the detection thresholds for the different noise conditions gives the distances at which a miner should be detected. These are given in Table l* below. [ ] The text also gives the increase in detection ranges which should occur if steps are taken to increase S/N by 10 dB. We feel that 10 dB is a conservative estimate of the improvement possible. During an actual rescue operation, the seismic crew and system should be capable of making on-site estimates of their detection capability, based on measurements of the site noise, and upon the best available estimates of the

Jan 1, 1974

By Richard J. Mainiero, Marcia L. Harris

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.

By J. B. F. Champlin

The continuing development of the nuclear industry in the United States requires a program of waste disposal that insures against the release of large amounts of radioactivity to the environment. This paper describes research on one proposed means of disposal of this waste, that of injection into geologic formations at depth. Nuclear production plant wastes were simulated and injected into samples of sedimentary rock obtained from outcrops, quarries, and deep wells. Changes in the chemical and physical characteristics of the rocks caused by the interaction of ions and suspended particles in the waste solutions with the cementing material and claylike particles in the rock are discussed. Laboratory tests show that nuclear wastes can be injected into many natural porous, permeable geologic formations. Injectivity can be maintained over a longer period by monitoring the ionic balance and particle-size distribution of waste streams. The combination of permeability and porosity with low cation-retention capacity, as exhibited by most sandstones, would satisfy the engineering requirements for the subsurface disposal of nuclear waste. Shales and clays with their low permeability and high cation-retention capacity would make excellent confining formations. The amount of cation retained by sedimentary rocks increases with increasing valence or concentration of the cation or decreasing brine concentration. The use of rock cores as model reservoirs had proved successful in determining some of the parameters that need to be considered in full-scale field disposal of wastes.

Jan 1, 1967

By Thomas J. Peters

The U.S. Bureau of Mines studied the 63,9SS-acre Hanson Lakes study area, including the Ten Mile-East and part of the Ten-Mile West RARE II areas, plus additional acreage, all proposed at times for Wilderness designation. The study was part of a Idaho Land Assessment Program with the Idaho Geological Survey and the U.S. Geological Survey, to provide minerals information for land-use decisions, and ensure domestic mineral supplies. The area is at the north end of the rugged Sawtooth Range and includes parts of the Sawtooth National Recreation Area which is closed to mineral location. The Copper Mountain. Elk Mountain, and Observation Peak mineralized areas are in the study area, but only Copper Mountain is open to claim location. It is on the trans-Challis fault zone and contains Tertiary granite which is favorable for mineral deposits of gold, beryllium, niobium, REE (rare-earth elements), tin, molybdenum, copper, silver, and lead. Identified resources are 1.9 million tons of flake graphite at Elk Mountain, but much more graphite occurs in the vicinity REE occurs in 18 black sand placer sites along the lower reaches of study area streams just outside the study area, on Cape Horn Creek, Marsh Creek, and lower Valley Creek flood plains, and at one hydrothermal site near Observation Peak. Hydrothermal REE is commonly low in? by-product thorium. a radioactive disposal problem. Many advanced REE applications enhance the quality of life, and future uses in superconductivity may reduce energy consumption. Seventeen lode, one geothermal, and 11 placer prospects were examined. Workings totaled about 20 adits, one shaft, several open cuts, and numerous small pits. Approximately 500 mining claims have been located or relocated in the study area, including a 200-claim block for disseminated molybdenum.

Jan 1, 1992

With IIT research institute as a cosponsor, this seventh mineral waste Utilization Symposium was funded by the Bureau of Mines through its Division of Mineral Resources Technology. Environmental scientists and engineers from five countries (Canada, Netherlands, Austria, England, Guatemala) besides the United States participated in the symposium, which was held Oct. 20-21, 1980, at the Chicago campus of IIT Research Institute. Of the 25 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial waste, and scrap metal, 21 are summarized herein.

Jan 1, 1982

By D. E. Redmon

Exploration of hidden mineral deposits becomes increasingly important as known ore reserves are depleted. The primary objective in any exploratory program is to obtain enough reliable information to evaluate accurately the potential of the mineral deposit. Constant improvement in equipment and technique has established drilling as one of the most valuable methods of exploration. This paper presents the results of studies of several drilling methods currently used in the search for uranium deposits in sedimentary formations from surface drill sites. Also presented is a description of drilling with wire-line equipment from an underground location in metamorphic rocks. The studies were conducted in the Colorado Plateau area and in northwestern New Mexico and Wyoming. Statements of a general nature pertain to conditions or situations existent in those areas.

Jan 1, 1960

By J. P. Dunford

This U.S. Bureau of Mines report describes the development of a yielding steel post for underground mine support. The report covers concept development, laboratory tests, modifications, and field evaluations. The objective of this work was to develop a stiff support member capable both of supporting high loads and yielding when excessive amounts of mine entry closure were present. The 6-to 7-ft steel post was designed to yield nearly 2 ft while maintaining a 45-ton (force) load. The post is a three-piece unit consisting of top and bottom telescoping legs and a separate foot bracket. It develops its load-carrying characteristics when the lower pipe, with an attached interference ring, is forced into the larger top pipe. Laboratory tests were used to determine critical loads and post performance for various post lengths. Field tests showed that the posts could perform in actual mining conditions. The post has the ability to provide support in highly yielding ground and also, because of its slender profile, enhance ventilation and provide more area for travelways and escapeways. The design is simple enough to allow for fabrication at most mine shop facilities.

Jan 1, 1989

By Alan R. Buehler

The Bureau of Mines conducted a mineral investigation of the 10,500-hectare Cache Peak study area in 1992; the area had been proposed as wilderness. Bureau personnel examined and sampled prospect workings; 14 rock and 20 placer samples were taken during the investigation. The study area is centered about 40 km south-southeast of Burley. Idaho, in the Sawtooth National Forest. There were seven mining claims located inside the study area, and one additional historical mining claim location. Gold, silver, copper, lead, zinc: Possible resource, poor exposure precludes estimate. Marble: Several million tonnes may be suitable for a variety of uses; markets too distant to favor mining. Sand and Gravel: Several million m3, but markets and transportation costs do not favor mining. Quartzite: Several million tonnes may be suitable for metallurgical purposes; however, markets are too limited to mine. Slabs have been quarried at three localities adjacent to the study area, for decorative stone. Production: In 1979, two tonnes of ore were produced and a plan of operations was submitted calling for approximately 5 km of access road for the Last Chance mine. Decorative stone production was not recorded.

Jan 1, 1993

By William H. Pomroy

This report describes Bureau of Mines research that led to the design, prototype fabrication, and successful proof-of-concept testing of an improved stench fire-warning system for underground noncoal mines. Stench systems are the most widely used means of warning driers in underground noncoal mines of fires or other emergencies. A stench system alerts miners that an emergency condition exists by injecting an odorant into the mine air. Although stench warning systems have been used successfully for over 60 yr, present systems suffer several serious shortcomings, including odorant toxicity, unreliability of warnings, widely varying stench concentrations, and others. In 1980, the Bureau began a research program to upgrade the stench warning system. The resultant system overcomes the deficiencies of existing systems by substituting tetrahydrothiophene for the commonly used ethyl mercaptan stench odorant, and through the use of a specially designed stench injector. The improved injector reliably meters stench fluid into either ventilation-air or compressed-air streams at a precisely controlled rate. Prototype hardware has been fabricated and proof-of-concept tested under bath laboratory and in-mine conditions.

Jan 1, 1985

By Melvin E. Poad

This Bureau of Mines report presents two phases of a research program to evaluate a single-entry system for longwall development. Organizations participating in the program; which began in July 1971, include the Bureau of Mines, the Mining Enforcement and Safety Administration, and the University of Utah, working under a cooperative agreement with Kaiser Steel Corp. at its Sunnyside mine in Utah. Part 1 of this report describes the present longwall mining practice, including a brief history, and discusses the advantages and disadvantages of a single-entry development system and its introduction in the United States. Part 2 of the report presents the research program; test design, instrumentation for ground and support evaluation, and the test results from the No. 2 mine. Subsequent reports will describe the research conducted in the No. 1 mine.

Jan 1, 1977

The Sago Mine Disaster, on January 2, 2006, placed renewed focus on several different aspects of safety in the underground coal mining industry. One area which received increased attention since Sago and other underground coal mining events is the concept of Safety Culture. This report describes the results of a pilot Safety Culture Assessment implemented at a small Appalachian underground coal mine, hereafter referred to as the Mine. The purposes of this pilot assessment were to (a) evaluate the feasibility and usefulness of a methodology for assessing safety culture that had previously been developed for use within other industries, (b) to initiate an investigation into the understanding and defining of the existing safety culture of the underground coal mining industry, and (c) provide meaningful and useful recommendations for the participating mine for their consideration in their ongoing quest to enhance their existing safety culture. This pilot assessment was conducted in July 2007. The report provides information regarding the presence or absence of safety culture characteristics within the Mine. Observations regarding the characteristics of the Mine?s safety culture that should be sustained are presented. Areas in need of attention and management focus to improve the Mine?s safety culture are presented as well as recommendations for moving forward. Safety culture characteristics that are important for the existence of a positive safety culture have been identified to include: - Safety is a clearly recognized value in the organization. - Accountability for safety in the organization is clear. - Safety is integrated into all activities in the organization. - A safety leadership process exists in the organization. - Safety culture is learning driven in the organization. - A process for establishing a strong and effective Safety Conscious Work Environment (SCWE) is in place. Performance objectives are associated with each of the safety culture characteristics and particular behaviors and attitudes have been identified that can be measured to evaluate these objectives. Using a methodology originally developed with the support of the U.S. Nuclear Regulatory Commission, an assessment of selected organizational behaviors and attitudes was conducted to evaluate the Mine in terms of these safety culture characteristics and their associated performance objectives. The methodology involves obtaining a variety of quantitative and qualitative information, using multiple data-gathering methods. The information collected is largely based upon the perceptions of the individuals in the organization. The evaluation is a ?point in time? snapshot of the Mine, but cultural beliefs and assumptions do not change quickly. The feasibility and usefulness of the methodology was successfully demonstrated during this pilot assessment. All aspects of the methodology including functional analysis, structured interviews with accompanying behavioral scales, work observations, and the paper and pencil

Aug 1, 2007

By C. W. Huggins

The primary objective of this Bureau of Mines research was to measure the size distribution of respirable quartz collected at metal mines, nonmetal mines, and processing plants to select the best reference standard for use in quantifying quartz in mine and plant dust samples. The secondary objective was to size all the nonquartz particles collected at the same sites. Particle size measurements were made on 29 samples using a scanning electron microscope in the backscatter mode of operation, interfaced with an image analysis system. The Mine Safety and Health Administration, Denver, CO, provided the 29 samples, which were collected at mines and processing plants in 19 states. The accumulated particle size measurements indicate that NBS 1878, minus 5-f.lm Hin-U-Sil, and minus 5-f.lm Supersil would be preferred over Silver Bond B as reference standards for most quantitative determinations by X-ray diffraction and infrared spectrometry. The respirable dust samples collected at sand plants, however, would be better served by a new reference standard having a quartz particle size distribution of approximately 2.2 um, as none of the four existing reference standards matched closely with them. Commercially available NBS 1878 and minus 5-um Hin-U-Sil CQuid be used as reference standards for 28 of the 29 samples studied in this investigation.

Jan 1, 1986

By Robert E. Wallhagen

The froth foam seal topping system is part of a system for remote sealing of mine passages using flyash transported pnuematically from the surface. Making the final 5 percent of the seal with a foamed-in-place fire retardant polyurethane reduces the required flyash volume by 50 percent and provides a more reliable seal. Foam components are held at the surface under proper conditions of temperature and pressure; then conveyed down the borehole through individual hoses and mixed at the bottom with a static mixer. The polyol component is pre-mixed with fluorocarbon-12 which, when released from system pressure in the mixer, boils and causes the foam to expand. Difficulties in handling this particular foam formulation are offset by a flame spread index well below the 25 level by ASTM E-162 normally required for under-ground applications. Isocyanate, polyol (TDI) and catalyst are conveyed to the downhole package by three separate lines. Five additional lines operate the valving and convey solvent so that the mixer and package lines can be flushed immediately after foaming. The eight-hose bundle is provided in segments of several lengths so that bore-hole depths can be matched. Cast-in-place plastic cylinders hold the bundle together and transfer the weight of the hose through a special quick-release clamp to the crane's wire rope. The downhole package and hose bundle are deployed using a specially designed winch and crane system capable of borehole deployment to 1500 feet.

Jan 1, 1977

By Thomas W. Camm

In this U.S. Bureau of Mines report, mine and mill cost models are presented to make quick estimates of the cost to develop mineral deposits in the desert region of the Southwest United States. Regression analysis was used to generate capital and operating cost equations for each model in the form Y = AXB, where Y is the cost estimated and X is the assumed daily capacity in short tons. A and B are constants determined by the regression analysis. Each is broken down into 11 subcategories to facilitate escalation of costs for inflation and to increase their versatility in economic evaluation work. This report contains 2 open pit models, 6 underground mine models, 11 mill models, and cost equations for access roads, powerlines, and tailings ponds. In addition, adjustment factors for variation in haulage distances are provided for open pit models and variation in mining depths for underground models.

Jan 1, 1991

By Bruce I. Thomas

As a part of the United States Department of the Interior program for developing natural resources in Alaska, the Bureau of Mines studied the tin-bearing gold-placer deposits in the Tofty area of the Hot Springs district in central Alaska. The principal objective of the Bureau's work was to obtain facts about the extent and character of the placer deposits (including tailing) to indicate the economic or strategic tin-production potential of the Tofty "tin belt." A secondary objective was to determine (if possible) the bedrock Source of the cassiterite and other minerals found in the placer deposits. The placer phase of the work was begun in July 1954 and was continued during the 1955 and 1956 field seasons. Extensions to, and connections between, known placer channels were sought by 82 churn-drill holes. The Bureau drilling did not expand the placer deposits beyond the limits established by drift-mining operations and by previous drilling done by private concerns.

Jan 1, 1957

By D. R. Tweeton

The U.S. Bureau of Mines, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research Organization, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in locating a brine solution simulating in situ leach solution or a high-conductivity plume of contamination. The brine was approximately 160 m below the surface. The testsite was the University's San Xavier experimental mine near Tucson, AZ. Geo- physical surveys using surface and surface-borehole, time-domain electromagnetic (TEM) induction; surface controlled-source audiofrequency magnetotellurics (CSAMT); surface-borehole, frequency- domain electromagnetic (FEM) induction; crosshole FEM; and surface magnetic field ellipticity were conducted before and during brine injection. The surface TEM data showed a broad decrease in resistivity. CSAMT measurements with the conventional orientation did not detect the brine, but measurements with another orientation indicated some decrease in resistivity. The surface-borehole and crosshole methods located a known fracture and other fracture zones inferred from borehole induction logs. Surface magnetic field ellipticity data showed a broad decrease in resistivity at depth following brine injection.

Jan 1, 2010