Search Documents

By G. J. Colaizzi

The Bureau of Mines, at the request of local authorities in Rock Springs, Wyo., investigated and conducted through contracts a multistage program of exploratory drilling and pumped-slurry backfilling of 15 areas of potential subsidence in abandoned mine workings underneath that community. Initially, the Bureau in 1969 had recommended a program of gravity blind flushing of some of the inaccessible mine voids, and in 1970 a new technique, the pumped-slurry injection process, was tested for the first time in a site adjacent to the city's area of severe surface subsidence. Success of this initial testing program, and of a large-scale project in Scranton, Pa., led to further large- scale projects, funded by Congress, that resulted in the successful back- filling not only of all 15 target areas of potential subsidence in Rock Springs, but also of several areas in other States. Total cost of the projects in Rock Springs, including the original pumped-slurry test, was $3,243,993. A total of about 923,000 tons of sand was injected hydraulically into mine voids, rendering 178 acres of residential and central-downtown areas of Rock Springs less susceptible to subsidence damage. The pumped-slurry method was proved to be much superior to the gravity blind flushing method in term of the amount of solids that could be injected underground through a single borehole. However, there are special conditions that make this technique more or less applicable in different areas or underground configurations, as noted in the report's conclusions.

Jan 1, 1980

Laboratory tests were conducted by the U.S. Bureau of Mines to determine respirable dust reduction effectiveness of and interaction between face airflow and water sprays for a continuous miner. Increases in exhausting face ventilation from 3,000 to 9,000 cfm, in waterflow from 15 to 35 gpm, and in water nozzle operating pressure from 80 to 200 psi were evaluated. Results indicated that airflow had the greatest individual impact on reducing dust levels, with concentrations at return and operator sampling locations reduced by as much as 57% and 99%, respectively. Regression modeling was utilized to predict dust concentrations over the range of values tested for the control parameters. Interactions between the control parameters were significant and often defined an optimum level where further increases in that parameter failed to produce additional dust reductions. Increasing airflow to 8,400 cfm, waterflow to 25 gpm, and water pressure to 140 psi typically reduced dust concentrations at operator and return locations. Application of a control parameter above these levels can provide additional dust reductions if used in conjunction with appropriate levels of the other two control parameters. Otherwise, higher operator dust levels may result and can be attributed to increased rollback and/or airflow turbulence.

Jan 1, 2010

By E. C. Fitch

This report discusses fire-resistant hydraulic fluid safety from three different directions. First, results of a survey prepared for the Fire Resistant Hydraulics Journal by the staff of the Fluid Power Research Center are analyzed. Second, operational limitations of fire-resistant hydraulic fluids are examined. Finally, laws and standards of various foreign countries are investigated. Three conclusions are derived from a close study of fire-resistant hydraulic fluid safety from these three directions. First, a significant number of experts in the fluid power industry are no in agreement about aspects of fire-resistant hydraulic fluid fire-resistance and toxicity. This indicates a need for more in depth research. Second, the use of fire-resistant hydraulic fluids involves a compromise between the decreased fire hazards and increased toxicity and machine incompatibility problems. Finlly, major foreign governmental agencies have thorough laws and standards concerning fire-resistant hydraulic fluids. These laws and standards may provide a solid framework for further international research into fire-resistant hydraulic fluid safety.

Jan 1, 1979

By E. R. Maize

[he scconG rcport of :his st?rI.org 8cdt with o3servatioi:s of conver- gence of roof an4 floor at t!x*re: ?.cc.-.tioris iri til~ ClVucible mine of kke Cru- cib1.o Fuel Co. Data on sl:'ociacnce ?.rd Lztcrcl mwe:~cnt cf the surface were .:lven for two of these areas, a-12 it was mentioned that ~lr~~ilar data were being obtained on a ?art of Pe:sc:rlvtzr.ia Fii~l?trr.y FE:, ~i!lic;l pcser: over the third area. 'I'hie hichw~ :LEO FasseE over t!lc ITenncoli::. :.line of the Bnckeye Coal Co. 9 milcs to ';he so-lth, cnd at P. l~tcr C'..att: ~.nr?r.,cc?r:cntS *.rere mnd.e to make similar observati on3 there. This y: pr mrnmri:.c n Czto obtnino? at those two locetionn,]

Jan 1, 1941

By R. H. Church

As part of the research effort of investigating the effects of microwave energy upon the chemical and physical properties of different minerals and ores, the Bureau of Mines has conducted basic research into identifying those properties of minerals that are affected by microwave energy, namely, the dielectric constant and loss tangent. These properties were determined utilizing the theory of microwave propagation in a coaxial waveguide filled with a dielectric material and measuring the input impedance with an RF impedance analyzer that operates from 1 MHz to 1 GHz. By knowing the microwave frequency and filling the waveguide with a powdered mineral, the dielectric properties of the mineral sample were determined. From these dielectric properties, theoretical microwave heating characteristics of each mineral could be calculated. These same mineral samples were then irradiated by a 915 MHz 30 kW variable power microwave oven and dielectric heating studies were performed. A comparison of the theoretical heating characteristics and the results from actual dielectric heating studies was conducted to evaluate the dielectric property measurements on each mineral. This report presents the results of the Bureau's research in identifying the dielectric properties of low-loss minerals according to the mineralogical classification scheme along with their irradiation studies. Though far from complete, this study represents some of the more frequently encountered low-loss minerals.

Jan 1, 1988

By Brian M. Harney

The technique of remote sensing, used for many years by earth scientists, is being applied to the detection and monitoring of air pollution. Instrumentation being developed is of a very diverse nature and is effective, Fn varying degrees, at ranges from 1,000 meters to the altitude of a space satellite. This paper describes a number of the recent developments in this new field. Instruments based on spectroscopic, laser, and photographic systems are discussed. Sensors are being developed which utilize correlation spectrometry, interferometry, Raman scattering, Mie scattering, laser line absorption, and simple photographic detection.

Jan 1, 1973

By R. E. Hershey

1. Reserves were estimated for three coal beds: Lantana, Sewanee, and Richland. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 34 million short tons as of Januray 1, 1954. Of this total, 15 million short tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient to permit making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By Edwin C. Reeder

This paper, describing milling methods and costs at the Hillside Fluorspar Mines at Rosiclare, Ill., is one of a series being prepared for and published by the United States Bureau of Mines on non-metallic milling methods. The milling practice described is that of one of the large mines in the Kentucky-Illinois fluorspar field in southern Illinois and western Kentucky, on the Ohio River. Milling methods throughout the district are similar in their general principles, although details vary considerably in different plants.

Jan 1, 1932

By Allan M. Johnson

Case histories were used to document and evaluate deficiencies in underground mine closures which have resulted in post-operation problems such as subsidence shaft failures, acid or toxic water drainage and others. Three different underground mining districts in the United States were investigated; 1) an iron mining district in Michigan 2) coal mining districts in eastern Ohio and southern Illinois and 3) three metal mining districts in central Colorado. Previous work in the Michigan district on problems with subsidence and acid water drainage provided the background from which the concept for this project was developed Student investigators working towards their MS degrees in Mining Engineering did the work on the eastern coal and western metal districts. The combined studies show that problems from acid water drainage, subsidence and inadequately protected mine shafts are the most severe and widespread. Suggestions of a technical nature are presented as partial solutions to some of these problems. It was determined that pre-closure evaluations could result in the identification of some potential problems that may occur after the mine is closed. Early recognition of these problems would be an advantage for at this time more options are available to the mine operator to either prevent them or to plan for their occurrence. Mine closure and reclamation should be considered as a part of mining and be incorporated in the mining plan. This would result in reduced environmental impact and would be achieved at a lower overall cost to the mining companies and to society. The role of water in the occurrence of several types of subsidence during mine flooding was significant at some mines in the Michigan district. These mechanisms which involve, friction reduction, gravity loading, overburden transport and hydraulic forces in a flooded mine probably have a broader effect than is currently recognized. Control of these processes may offer some interesting options during mine closure. It is recognized that technical solutions alone cannot provide all of the answers to problems associated with underground mines. Education, modified attitudes on the part of regulators and operators, and a more realistic perception of the importance and value of mining by the general public are also needed.

Jan 1, 1983

By Michael Hood

High-volume, low-pressure water jets have been employed for erosion of loosely consolidated rocks for centuries. This excavation method finds application in specialized circumstances even today. The use of high-pressure, low-volume water jets for rock cutting is more recent and was made possible by the development of high-pressure water pumps. Despite the benefits often claimed for these systems, high-pressure water jets still have not found widespread application. In this report, the U.S. Bureau of Mines has reviewed the various methods that have been employed using water jets to break rock and has focused on one method, termed "jet-assisted cutting," which was determined to be the closest to commercial development. The current state of knowledge based on laboratory and field experiences using this cutting method is reviewed, and possible future developments for this approach to excavation are assessed.

Jan 1, 1990

By F. L. Wideman

This report describes the sinking of No. 3 shaft at the Westvaco mine. It is one of a series of publications of the Bureau of Mines on mining methods and practices in the United States. The Westvaco mine is in Sweetwater County, Wyo., approximately 23 miles northwest of the town of Green River (fig. I), There are no permanent habitations in the vicinity of the mine, and employees live in Green River or Rock Springs, Wyo., 14 miles us t of Green River. The mine plant is on a windswept, treeless plain, from which low buttes and flat-topped ridges rise. The altitude at the collar of No. 3 shaft is 6,351 feet. The climate is arid, with temperatures as low as 40° below zero in the winter. Blacks Fork, a tributary of the Green River and a perennial stream, flows near the mine.

Jan 1, 1959

By C. C. Hustwit

The U.S. Bureau of Mines formulated a new mathematical model to characterize iron oxidation. The new model is intended to replace the currently used model, recommended by the Environmental Protection Agency (EPA), for most acid mine drainage (AMD) treatment applications. The new model was evaluated in a series of five synthetic AMD treatment tests. The initial ferrous iron concentrations ranged from 800 to 2,400 mg/L. In these tests, the Bureau model underpredicted the measured ferrous iron oxidation rates by a range of 3.24 to 8.03 pct. This was considered to be in close agreement after consideration of experimental error. The model proposed by the EPA was also evaluated using the same test data. The EPA model underpredicted the oxidation rates by a range of 77 to 100 pct in four tests and overpredicted by 19 pct in one test. The model formulated by the Bureau expresses that the rate of iron oxidation is a function of a treatment system's oxygen transfer efficiency and is independent of ferrous iron concentration when treated to near-neutral pH's. A new test method for evaluating oxygen transfer in flow-through reactors is also described.

Jan 1, 2010

By K. R. Dorman

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed a five-piece precast concrete drift set for a small opening and tested it to destruction in a straining frame. Twenty-seven tests were made with three sizes of members using three loading conditions. In addition, six tests were made with sets in a distorted configuration, Test results and typical failure patterns are presented. A comparison of results with those previously reported for the three-piece set shows the five-piece set supports considerably larger total loads than does the three-piece set of equivalent cross section designed for the same size of opening. Recommendations are made for improvements in design.

Jan 1, 1969

By Walter T. Lewieki

"INTRODUCTION Numerous deposits of iron ore are found in Cherokee, Bartow, Floyd, and Polk Counties in northwest Georgia. The deposits are generally small and irregular in shape. The ore is usually referred to as ""brown ore"" and is predominately limonite. The crude or ""bank ore"" has to be washed and concentrated before being shipped.The proximity of the deposits to the Birmingham furnaces and a favorable freight differential permit the operation of many deposits that otherwise would be uneconomical. The district produced 413,468 long tons of brown-ore concentrates, averaging 45.53 percent iron in 1943.The necessity of developing additional iron-ore reserves for the war energeucy to supplement the production of the Birmingham district, prompted the Bureau of Mines to initiate exploration of the more promising northwest Georgia deposits. Thirteen properties in the four counties were explored during the program (fig. 1).HISTORY AND PRODUCTIONSeveral furnaces were operated in the district until the early 1900's, ranging from charcoal furnaces to more modern plants with capacities up to 50 tons of pig iron. No furnaces have operated for about 40 years, the product being shipped to Alabama and Tennessee.Bartow County iron mining is declining, although formerly it was the principal producer of the district. Most of the known merchantable ore deposits have been exhausted. For the past 3 years the Mitchell-Hodge mine has annually produced about 225,000 long tons of concentrates containing 46 to 43 percent iron and at present is the only large producer in Bartow County."

Jan 1, 1946

By H. R. Pierce

A gas well has a certain definite capacity to deliver gas from the gas sand through the producing string of pipe. This capacity depends upon the pressures in the sand; that is, a well will deliver gas at a rate of flow which is determined by the formation or "shut-inn pressure in the sand and the back pressure at the face of the sand in the well. The three factors, rate of flow, formation or "shut-in" pressure, and the back pressure, for a given well, can be written into a fundamental relation which is strictly applicable only to that well. This relation can be used to determine the capacity of the well to deliver gas from any formation pressure against any back pressure held at the f ace of the sand in the well. Studies have been made of the deliveries of 400 gas wells operating under different conditions of pressure, Most of the wells which have been studied are in Osage County, Okla.; however, several representative studies have been made on wells in southern Louisiana, southern Texas, the Texas Panhandle, and West Virginia.

Jan 1, 1929

By J. Wade Watkins, Joseph W. Horne, Arthur Matzick

"A successful procedure for the recovery of a valuable product from weathered tank-bottom settlings has been developed in the laboratories of the Bureau of lines and used in a field pilot plant. These heavy emulsion settlings, generally regarded by the industry as waste material, have usually been drained into open pits or storage ponds and eventually destroyed.Laboratory examination of the waste material shows it to consist essentially of a ""water-in-oil"" emulsion containing a considerable volume of congealed ""paraffin."" This paraffin is mainly high-melting-point wax; known in the industry as microcrystalline wax, for which there is an increasing demand.Because of the physical properties of this wax, the tank-bottom settlings are not responsive to conventional methods used for demulsifying ordinary crude-oil emulsions.The work upon which this report is based was conducted by the Bureau of Mines in cooperation with -the Kansas State. Board of Health and with special cooperative agreements-with the Cities Service Oil Co, Bartlesville, Okla., and the Bareco Oil Co,. Barnsdall, Okla. The studies were made under the general supervision of R. A. Cattell, chief engineer, Petroleum and Natural-Gas Division, Bureau of Mines, Washington; D. C., and H. C. Fowler, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.Gratefully acknowledged are the assistance and cooperation given by the Cities Service Oil Co. of Oklahoma and especially by M. J. Kirwan, manager of production, and by Q. E. Beecher, general superintendent of production, Bartlesville, Okla., and to members of their staff at Oil Hill, Kans.The assistance and suggestions of V. R. Oakley, general superintendent, E. R. Wiles, director of research, L. G. Willis, field engineer in charge crude-oil supply, and Gerald DeWalt, chief chemist, and his staff of the Bareco Oil Co., Barnsdall, Okla., were of much value in the laboratory and recovery work."

Mar 1, 1946

By V. L. Burdick

A literature review of current uses of Mn02 in ceramic applications with suggestions for future research. Historical background, oceanographic distribution, geology, exploitation, law and politics. Uses of Mn02 in ferrites, semiconductors, catalytic processes, thermo-luminescence and photochromic materials. Select bibliography of 33 items, plus 129 references.

Jan 1, 1980

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least-radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By W. R. Hardwick

This information circular describes open-pit mining methods and practices of the Bagdad Copper Corp., Yavapai County, Ariz. It is one of a series being prepared by the Federal Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. A brief history of the Eureka district and of early developments at the [gdad] mine is given, and the are deposit is described with particular emphasis on those characteristics (physical, economic, or engineering) that affected the choice of mining methods. Prospecting, exploration, and sampling and estimating the tonnage and grade are outlined. Development of the open-pit mine is shown. Mining methods, including breaking ground, primary drilling and blasting, secondary drilling and blasting, loading, transportation, engineering, and operating control, are described. A brief summary of mining equipment is given. Percentage of extraction, production rate, mine drainage and water supply, wage, contract, and bonus systems, safety and fire prevention, and the processing plant also are described. The last section gives a breakdown of such costs as are available for publication.

Jan 1, 1959

By Maurice E. Bailey

The purpose of this study is to determine worker acceptance of modified mine equipment at various intervals during a twelve month period. A survey instrument was administered to the workers by two experienced miners in four interviews. All four interviews showed a significant positive response to all modifications, except the small size of the cab of the shuttle car; however, the small size produced significant negative responses with respect to comfort in each of the four interviews. Initially, (interviews one and two), there were significant negative responses with respect to manufacturer receptivity to operator suggestions and program management follow-through on operator suggestions; however, the third and fourth interviews showed no significant negative responses with respect to these items. Likewise, there were significant neutral responses in the first two interviews; however, the third and fourth interviews showed no significant neutral responses with respect to these items.

Jan 1, 1975