Search Documents

To identify the most successful methods now in use for controlling respirable dust in longwall mines using double-drum shearers. Approach Conduct dust surveys at six longwall mining sections that use double-drum shearers and are regularly in compliance with the Federal Respirable Dust Standard, to identify effective dust control techniques. The selection of mine sites was based on recommendations provided by the Mine Safety and Health Administration. Instantaneous and short-term gravimetric instrumentation make it possible to isolate longwall dust sources and to determine the effectiveness of dust control techniques. (These procedures were developed by the Bureau of Mines, and are described in detail in Technology News Bulletins 134 and 135.) Production levels, and seam heights at each of the six longwall sections were: 53", 700 tps; 60", 800 tps; 72", 1000 tps; 79", 1500 tps; 84", 2000 tps; 96", 1500 tps. Survey Results Three effective dust control techniques were identified. 1. Shearer Operators on Intake Side of Lead Drum-At all mines surveyed, an important factor in controlling dust exposures at the shearer is the use of a cut ting sequence that allows the shearer operators to work most of the time on the intake air side of the lead drum. Dust profiles, like those plotted from data at two mines (see the graphs), show the large gradient in dust concentrations that can

Jan 1, 1982

By Fred N. Kissell

In This Chapter [Early indicators of a gas problem How the methane hazard is reduced Ventilation principles for gassy tunnels Monitoring for gas Eliminating ignition sources and The all-important human factors component] This chapter gives guidelines for preventing methane gas explosions during tunnel construction. Emphasis is placed on assessing the hazard potential, on ventilation principles, and on monitoring for gas. The chapter also emphasizes the importance of human factors in reducing explosion risk. Ensuring safe conditions is much more than just good engineering design. It also involves the every-day vigilance of those working underground. This does not imply that the engineering design can be ignored, only that the job of providing safe conditions has just begun with design. EARLY INDICATORS OF A GAS PROBLEM For the engineer planning a tunnel project, reliable early indicators of methane are scarce. How-ever, the local geology can often provide some information.2 Carbonaceous rocks and tar sands are a likely methane source. Gas is also a distinct possibility if it is known to be present else-where in the same sequence of geologic formations. Swampy areas, sewerage systems, and landfills are also candidates because the decomposition of organic materials produces methane. The gas in a tunnel can originate in the strata being excavated, or it can migrate a considerable distance from adjacent strata. Test borings at the project site can also serve as initial indicators of gas. Methane has no odor, but may be emitted along with gases that do. If gas is emitted from the borehole, a sample may be collected by inserting a tube into the hole as far as possible and pumping the gas out. The gas sample should be collected in a sampling bag or canister for later analysis by a chemical laboratory.3

Jan 6, 2006

By Murali M. Gadde, John A. Rusnak

Rock mass classification systems are extremely useful for site characterization and have been employed by the rock mechanics community for several decades. While empirical in nature, the classification systems provide a viable means to quantify the nature of rock mass, which is necessary for stability analyses. In U.S. coal mines, the Coal Mine Roof Rating (CMRR) is the most widely used classification system for several purposes, including sup-port selection, chain pillar design, assessing the stability of extended face cuts, etc. The Analysis of Roof Bolt Systems (ARBS) is an empirical method developed from the CMRR to guide selection of roof bolts as the primary support system in U.S. coal mines. In this paper, the experience of Peabody Energy in applying ARBS to sup-port design is discussed. In general, data from the Peabody mines show that ARBS predictions match well with field conditions. Peabody, however, does not use ARBS as the stand-alone methodology for support selection. Peabody uses a two-pronged approach in which the support requirement is initially estimated from the classification method, and then numerical modeling is used to select the proper reinforcement system. Such an integrated approach is necessary, as ARBS suggests only the “amount of steel” that may be used to support the roof and does not specify which type of roof bolt to use. A case study is used to demonstrate the usefulness of ARBS and Peabody’s integrated approach to support design. Also, the application of ARBS at several Peabody mines showed a very good correlation with support cost. The correlation indicated a direct relation between bolting cost and the ARBS value.

Jan 5, 2007

Develop a method for control of groundwater inflow to chronically "wet" sections of underground coal mines, in order to reduce groundwater interference with mining activity and to minimize acid mine drainage. Approach In eastern coal regions, groundwater stored in fracture zones in the rock mass can create a significant water problem for underground mining operations. Fracture stored inflow to mine workings impedes mine productivity since storage water sources usually release at the active face, creating the poor mining conditions typical of a "wet" section. Fracture water can also contribute to AMD problems when the water subsequently contacts sulfide minerals in the coal, The Bureau of Mines has developed a mine-dewatering method that eliminates many of the problems associated with mine water inflow by draining these fracture zones before the water can reach the developing face and interfere with mining activity. How it Works The dewatering method removes large volumes of the stored groundwater through high-capacity pumping from a minimal number of wells placed strategically on fracture traces (the surface expressions of fractured rock zones). These fracture traces are located through low-level aerial photographic and geologic investigation. As shown on the map, dewatering wells are sited precisely on fracture trace intersections in order to take advantage of the increased pumping capacity gained from these zones of high permeability. Once well drawdown indicates that the stored water is depleted,

Jan 1, 1983

Develop an improved downhole geophone system with enhanced signal/noise ratio for collecting cross-hole seismic data used in tomographic reconstructions. Background The Bureau of Mines is conducting research in the use of cross-hole seismic tomography for detecting and monitoring leach solution flow during in situ mining. This technique requires the use of a downhole seismic energy source in one borehole and a downhole wall-locking receiver (geophone) in another borehole separated from the first by the region to be investigated. Bureau research personnel chose a commercially available air gun for use as the downhole seismic energy source. Unfortunately, commercially available downhole wall-locking geophones that the Bureau tested were difficult to operate in the field, often unreliable and generally inadequate in terms of their signal/noise ratio. Therefore, research personnel began to experiment with an alternative down-hole geophone design that could be used to collect adequate data in a wide variety of borehole and cross-hole field situations. Approach An attractive alternative geophone design would be one that would incorporate a pneumatically operated wall-locking system. As an integral part of the Bureau's existing field system, a portable, high- pressure/low-volume air compressor would have sufficient capacity to operate the air gun as well as several small high-pressure pneumatic linear actuators. This approach was the simplest and most compatible with the research activities being conducted at the site.

Jan 1, 1991

By Richard J. Mainiero, Sapko, Marcia L. Harris

Since 1988, there have been thirteen documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through near surface strata into structures or other enclosed spaces as a result of nearby trench blasting or surface mine blasting. From these incidents, there are thirty suspected or medically verified CO poisonings and one fatality associated with these incidents. To better understand the variables contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out a small-scale field study to identify key factors that may contribute to the migration of CO through the ground. NIOSH conducted single-hole heavily confined experimental test shots to measure the radial pressure pulse as it propagated through surrounding monitoring holes to determine if a relationship existed between the pressure pulse and resulting CO measurements afterwards. NIOSH also monitored blasts at an airport construction site. Following the detonations, the concentrations of CO, nitric oxide (NO), and nitrogen dioxide (NO2) were monitored for several days in the surrounding satellite holes. The peak CO measurements relative to distances from the shots were compared. Pressure histories and peak particle velocities (PPV) were measured at monitoring boreholes. It was found that the differential pressures recorded within the boreholes give some indication as to the likelihood of CO appearing, whereas the PPV measurements do not seem to be as good an indicator for potential CO migration. In this limited study, changes in barometric pressure had very little influence on removing the trapped detonation products, whereas applying a vacuum to the monitoring holes was effective in reducing the entrapped CO concentration.

The following additional studies are recommended: 1. Future development of the magnetic sludge process should involve optimization of the process variables; these include stirring rate, sludge heating time, aeration rate, method of preliminary sludge dewatering, and the effects of magnetic separation for final sludge processing. In addition, the matter of amenability of coal mine waters to treatment should be considered more thoroughly by means of a more comprehensive literature review as well as actual tests on mine drainage samples. 2. The technique of sludge freezing should be explored further. Emphasis should be given to conservation of energy in the process, and the filtration characteristics of the resulting sludges should be evaluated. 3. Further studies should be conducted on the feasibility of the CO2-addition approach to mine drainage sludge densification. The filtration characteristics of product sludges should be evaluated, and the possibility of recovering and recycling the residual alkalinity of the sludge, either directly as CaCO3 or as CaO plus CO2 after calcination, should also be explored further. 4. Efforts should be made to develop cost data for the conceptual processes involving magnetic sludge formation, sludge freezing, and C02 pretreatment, with the purpose of selecting at least one of these processes for further testing at a field site. 5. The use of inexpensive waste materials (e.g. fly ash, "red dog," slag) as sludge additives, possibly in conjunction with coagulant aids, should be considered further. Results of the present studies have indicated that such materials, employed in relatively large amounts, increase the density and enhance the filterability of sludges from lime neutralization of coal mine drainage. The use of pulverized blast furnace slag in this regard appears particularly promising, and studies should be made to ascertain its availability, relative cost, residual alkalinity, and behavior as an additive in conventional mine drainage treatment processes involving lime neutralization and aeration.

Jan 1, 1971

By William Wiehagen

This trainer?s guide is designed as a reference manual. The purpose is to offer information and examples to skills trainers to assist them in structuring training for new operators of Walk-Thru roof bolting machines. Trainers can use this manual as a resource for helping trainees learn, understand, and apply knowledge and skills. In this sense, the guide is not prescriptive. It is designed to offer information and trigger ideas on what might be done to accelerate learning to those who are new to the roof-bolting task. On-site trainers can modify this guide to fit their conditions, machines and equipment, and work procedures. They can integrate roof control plans, company policies and procedures, and operators? manuals from the manufacturers of the original equipment into this guide. Every trainee is different and will come to the job with varying levels of relevant knowledge and skills. The trainer?s decisions on where to start, how to organize the on-the-job and classroom training portions, and when and how to offer different aspects of the training will be based on (1) a pretraining assessment of the trainee?s knowledge and skills and (2) the trainer?s experience in conducting skills training. The ?Skill Check? section might be useful for deciding where training should start among miners who have underground experience but limited knowledge of roof-bolting techniques. Every job carries a learning curve and likely has a number of ?teachable moments? where significantly new knowledge and skills can be learned.

Aug 1, 2006

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX B - DEVELOPMENT OF FOAM-CONCRETE SLURRY MINE SEALANT 1. Introduction This appendix describes the results of an experimental development and laboratory evaluation of foam-concrete as a rapid setting, lightweight, self-supporting mine sealant material. Foam concrete, otherwise known as Aerated Concrete, is a form of lightweight concrete whose structure consists of air bubbles held together by a hardened cement mortar. Its principal applications are found in roofing, insulation, shock absorbing, and backfill. The air bubbles in foam concrete are formed either by chemical reaction in the wet, placed mortar, or by introducing a stable foam into the mortar during mixing. The mortar is usually a cement slurry with fine sand or fly ash as filler. Our attention focused on preformed foam concrete, since this is most adaptable to field applications. Equipment is available,* which simultaneously mixes and pumps a slurry of foam concrete. Such a slurry can be produced at a rate of up to 50 yards/hr and has been pumped in a 2-inch-diameter hose 1000-feet horizontally and 250 feet vertically up without significant bubble deterioration. One very attractive feature associated with the use of foam concrete concerns site logistics. Foam concrete can be generated with densities as low as 20 lbs/ft3, and hence the total number of

Jan 1, 1973

By Lon Santis, Scott Deitchman, John A. Decker

This report describes three cases of carbon monoxide (CO) poisoning in a manhole, including one fatality, from CO migrating through soil after nearby use of explosives. A municipal sewer project involved installation of new pipes and manholes. Work of the general construction contractor was interrupted when a subcontractor detonated 265 pounds of nitroglycerin-based explosive 40-60 feet south of the manhole to break up underlying rock. A construction worker who descended into the manhole 45 minutes after the explosion collapsed within minutes, and two co-workers descended into the manhole to rescue him. One rescuer retrieved the unconscious worker, and the other rescuer died in the manhole. All workers had elevated carboxyhemoglobin levels. In the subsequent NIOSH investigation, air monitoring was conducted with real-time instruments, and air samples were collected in Tedlar bags. Laboratory analyses of the bag samples collected near the bottom showed 1905 parts per million (ppm) CO, 19.5% oxygen, and 3% carbon dioxide. Direct reading instruments showed progressively higher concentrations as the sensor was lowered into the manhole. Subsequent chamber tests on sample explosive yielded 27 liters CO per kilogram detonated. Based on this value, the surface blast at the construction site may have produced about 3,250 liters (114.8 cubic feet) CO. The CO in this incident most likely was released from the nearby explosion and migrated through soil and fractured rock into the manhole. The blasting and construction industries should be made aware of this previously unrecognized CO exposure hazard associated with surface blasting. The extent of CO exposure from explosives used in construction is not known, and additional information on the extent of CO exposure must be collected. In addition, confined space entry procedures (including monitoring confined space atmospheres before entry) should be observed; CO monitoring of confined spaces in the presence of blasting can prevent future incidents such as this one.

Oct 30, 1997

By P. L. Swanson, S. Billington, F. M. Boler, L. H. Estey

Stabiity analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this US. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 1992

By Lynn L. Rethi, Barbara Fotta

Recent employment figures (taken from the Mine Safety and Health Administration's database) indicate that the number of independent contractor' employees working in the coal mining industry has doubled over the past ten years. As their numbers increase, they become a more visible segment of the industry. [ ] Increased exposure to mining hazards has also brought an increase in the number of fatalities involving independent contractor workers. One gauge that is traditionally used to evaluate the overall safety of an entity is the "number of fatalities." Over the five-year period from 1985-89, 27 independent contractor employees were fatally injured while working on coal mine property. This number increased to 45 fatalities during the subsequent five-year period from 1990-94. Nearly half of these fatalities (47%) were due to accidents involving powered haulage (See Table); 13% were electrical accidents; and 9% were machinery accidents. Combined, these three accident classifications accounted for 69% of all coal nine independent contractor fatalities. Information taken from fatality data is an important piece of the safety puzzle; however, other variables need to he examined in order to better define contributing factors associated with accidents. More specifically, information on trends in fatal and nonfatal accident and injury data is necessary before deciding what approach should be used to improve safety. In order to implement appropriate safety strategies, it is important for safety practitioners to examine all available lost time accident and injury information. The following coal industry data sites specific and present trends of independent contractor employees working in underground locations at coal mines, surface areas of underground coal mines, surface coal mines, and preparation plants. The data compares employment and accidents for time periods at the beginning and the end of a ten-year span from 1985 to 1994. Because the number of incidents involving independent contractors in certain accident categories during any one year may be small, three-year totals are used; the first three years (1985-87) of the ten-year period are compared with the last three years (1992-94). [ ]

Investigate and demonstrate the possible use of low-density (45-lb/ft3) foam concrete for sealing abandoned mine openings. Although foam concrete has been used in the construction and geotechnical industries for some decades, it has not previously been used in abandoned mint shaft reclamation. Approach A structurally engineered permanent mine seal for an abandoned coal mine shaft, using low-density foam concrete and other appropriate structural materials, was designed by the Bureau and installed at a field site, the No. 22 Shall in Logan County, West Virginia. The field work was conducted by a private contractor under the supervision of the West Virginia AML Section (WV AML). The No. 22 Shaft is situated immediately adjacent to a frequently traveled county road. A few feet away from the shaft is a branch of Pine Creek. On the other side of the road is a railroad line that serves an active mining operation located several miles away. The shaft measures 9.5 by 9 feet in cross section and is about 300 feet deep. It was used at one time as a dewatering shaft and still contains two large-diameter dewatering pipes with steel drive shafts inside them. Before the beginning of the reclamation, the shaft included a concrete cap a few inches thick, with a 4 - by 5-foot access opening covered by a steel grate. The interior of the shaft was quite humid, and considerable flow of water at the bottom of the shaft could clearly be heard from the surface. Methane tests were conducted that showed the shaft to be clear of this gas.

Jan 1, 1992

By John Owens, Marc Endicott, Hamid Maleki

This study presents a historic overview of the role of mobile roof support (MRS) technologies in improving stability and worker safety and presents the results of recent field evaluations of the MRS load rate monitoring device and other remote deformation-monitoring techniques. Field studies were implemented at two sites in cooperation among researchers from the National Institute for Occupational Safety and Health (NIOSH), Maleki Technologies, Inc., and J. H. Fletcher & Co. The objective of the field programs were to (1) study the interaction between MRS’s and coal mine strata and (2) develop and test suitable monitoring systems for assessing roof and pillar stability. An MRS consists of a roof canopy, four hydraulic cylinders, a caving shield canopy, and associated electromechanical systems mounted on crawler tracks. The machines are controlled by radio from a remote location and operate on self-contained power units. Typically, MRS’s have capacities of 5,340 and 7,120 kN (600 and800 tons). In comparison to posts, an MRS is capable of maintaining the yield load after significant amounts of roof-floor deformation. Because the mining cycle is accelerated, MRS’s help reduce the potential for time-dependent roof falls. MRS performance has been monitored in the laboratory under controlled static loading conditions and in the field under deep, two-seam mining conditions. Laboratory studies have quantified support capacity and system stiffness as a function of machine height. Field investigations have focused on determination of optimum operating conditions and development of warning systems that indicate excessive load on the machine and/or impending roof-pillar stability problems. Analyses of field data show that roof instabilities are influenced by (1) pillar failure, (2) pillar yielding, (3) mine seismicity, (4)geologic structures, and (5) panel layout designs and mining practice.Pillar yielding and failure (unloading) and seismicity can be conveniently monitored by the load rate monitoring device, but for consistent detection of roof falls, additional deformation measurements directly within the cuts are needed.

Provide an inexpensive, remote actuated, stench-gas system which reduces fire warning time to underground work locations. Approach A mine's pager phone hard-wire network is used to release stench gas from pressurized canisters located near working areas. The release is initiated by placing a coded message into a control phone at some central location. How It Works Currently, in most mines, the decision to release a warning stench gas is made by mine management after communication from the mine of a fire or similar potentially dangerous situation. Stench gas is then released into the ventilation air and/or compressed air lines for dissemination throughout the mine. This can result in significant delays in warning time. Often, surface personnel must travel to distant shafts, or other release points, wasting valuable time. Also, the time for ventilation air to circulate from the surface to working locations can be long and the effectiveness of compressed air as a stench transport agent depends on whether the compressed air is being used at the face. The Bureau of Mines, through a contract with MSA Research Corporation, has designed and tested a warning system which avoids these problems. The system consists of multiple, pressurized stench-gas canisters located under-ground in the mine-ventilation network so as to provide quick dissemination of the released stench gas to working areas. Each stench-gas canister is hard-wire connected to a nearby pager phone and from there to a control phone at the surface or at a central in-mine site. In the event of a mine emergency, the canisters are activitated to release stench gas by placing a coded message into the control phone. A low amperage Signal sent from the control phone to the receiver phone closes a relay, which activates a release mechanism on the canister.

Jan 1, 1984

By Christopher Mark, Anthony T. Iannacchione

Falls of ground continue to be one of the most serious causes of injury to U.S. miners. Of the 256 fatal injuries that occurred in mining between 1996 and 1998, 59 (23%) were caused by falls of ground (Table 23.1). Falls of ground affect some sectors of the mining industry more severely than others. For instance, nearly 40% of the 98 coal mine fatalities between 1996 and 1998 were caused by falls of ground. Underground miners are at much greater risk than surface miners. Nearly half (45 out of 101) of underground mine fatalities were attributed to roof, rib, and face falls, while only 6% of the 155 surface fatalities were caused by falls of highwalls or slopes. The goal of this chapter is to provide guidance to safety professionals tasked with preventing ground fall injuries. This chapter combines an analysis of the Mine Safety and Health Administration's (MS HA) accident and injury data with a survey of industry "best practices" to safeguard miners from ground falls. Ultimately, this approach can help to form the basis of a sound, proactive ground control program for the mining industry. SOURCES OF DATA All the injury data examined in this study were derived from MSHA's fatal investigation reports and the MSHA accident database. Because falls of ground often result in serious injury, MSHA "Fatalgrams" and fatal investigation reports provide a useful snapshot of ground control issues in the mining industry. These reports are available to the public (on the M FHA Web site at www.msha.gov). Fatalgrams, are one-page summaries that are usually published within a month of an accident. They contain very basic information about the accident with a graphic and a short section on relevant best practices. Fatal investigation reports are the official accident investigation reports filed by MSHA personnel. These reports contain general information about the mine, a, description of the accident, physical factors involved in the accident, a conclusion, and enforcement actions, Enforcement actions typically identify citations and discuss violations to the Federal Mining Law. MSHA also maintains comprehensive statistical data on the mining industry's accident and injury record. The law requires that mines file a report on every reportable accident that occurs, containing information on the accident's location, severity, classification, activity, and nature of injury A short narrative is generally included as well. Accident reports can be searched by many of the above fields.

By David C. Peters, Robert S. Crosson

A method of error analysis has been applied to the location technique of non-linear least squares iterative inversion in order to evaluate the resolving power of several seismic array configurations with various assumed earth models and errors and inaccuracies in arrival times. The results obtained demonstrate that lateral accuracies of location are improved significantly when the depth of the miner is known. Lateral location to within 100 feet appears achievable in many instances. If it is possible to refine earth models significantly beyond what has normally been assumed in this work by the use of on-site data, or if the mine is shallow (300 feet or less), accuracies of-about 30 feet or so may be attainable. Inaccuracies in earth models of about 5% are found to contribute much more heavily to these location inaccuracies than errors of a few milliseconds in picking arrival times; however, arrival time errors of 15-20 ms or above will dominate these model inaccuracies. The expected accuracy of location is found to fall off very rapidly as the miner moves outside the array. The strength of this effect depends markedly upon the geometry of the array configuration and can be reduced by careful design. Also, as the size of the array is increased, expected location errors within the array are not altered much, but continue to match the error associated with the smaller array over a larger area (assuming that all stations can still pick up the miner's signals). Better location accuracy, especially with respect to depth control is achievable in an earth where the velocity is depth-dependent (increasing with depth) than in one which is homogeneous. This is an advantage since the

Jan 1, 1974

By C. B. Manula, R. L. Sanford, R. A. Rivell

The need for a large capacity, high speed computer is more apparent in the revised model than in the original one. Core storage requirements for data and model logic have at least tripled. This dictates the use of one of the large modern machines such as the IBM 360-370 series or the Univac 1108 and 1110, which handle the model without the need for extensive program overlay. Computer time is expensive on these machines, however, and comprehensive analysis has gone into optimizing computer execution time consistent with model information flow sensitivity. For example, revised locomotive tramming routines have been developed which will significantly cut execution time compared to the previous version. Transceiver Applications The computer coding for the model has been developed to enable program execution and testing using a remote terminal on a time sharing system. In fact, nearly all of the coding, debugging, testing and modifications have been performed from a terminal during develop¬ment. The gaming options described in the Model Input Section of this report have been designed so that they are easily changed by the user from any remote site. One restriction on remote applications which could arise, however, is where highly detailed output options are specified, resulting in a large amount of output records which could be handled more efficiently on a high speed printer.

Jan 1, 1974

By William R. Barton

Dimension stones, with their almost infinite variety, have a broad range of properties and uses. Natural stone was beyond doubt the first mineral commodity used by man. Today dimension stone has widened to encompass building exteriors and interiors, decorative and ornamental modes, statuary, monuments, paving, curbing, flagging, roofing, and miscellaneous categories such as blackboards, surface plates, and honestones. For many purposes, it competes with greater or less success with alternate materials such as concrete, metal, brick, plastic, or glass. The almost ubiquitous geographic distribution of stone resources is the basis for a dimension stone producer industry in almost every State and in almost every land. In the United States, alone, dimension stone sold or used by quarries is valued at 2 million to 3 million dollars annually. Mining, finishing, transportation, and use technology have been modernized, resulting in a broader spectrum of stone products and new adaptions in use. Increased efficiencies also have been reflected in costs and prices and, coupled with gains that should be realized from current research, auger well for continued vitality of the ancient and honorable dimension stone craft.

Jan 1, 1968

By Will H. Coghill

The scope of this paper is such that it was deemed advisable to group the contents into several main sections. They are: Section 1. Geography and Geology. Section II. Historical Review. (a) Mining and Smelting in Alabama. (b) Milling. (c) Summary of Milling Research. These two sections are primarily a bibliography and summary of the research on the Birmingham Red Mountain ores up to the middle 1040's. Section III. Status of the Birmingham Iron Industry. This sect ion points out the extent to which the findings of the iron-ore research have been applied on a commercial scale. Also, a very brief description of the dependent and allied industries is included. The value of the Birmingham iron ore is greatly enhanced by the proximity of coal and dolomite. Thus the coal and coke industry and the dolomite industry are closely allied with and to a large extent dependent upon the possibilities of economic utilization of the Red Mountain iron ores. Section IV. Beneficiation Investigations of the Red Mountain Iron Ores. This is a record of the most recent, hitherto unpublished work of the Southern Experiment Station of the Federal Bureau of Mines, Tuscaloosa, Ala., on the chemical and physical composition not only of the Big seam but of most of the iron-bearing rock strata of Red Mountain.

Jan 1, 1946