Search Documents

Identify abnormal low-frequency blast vibrations. Develop blast design procedures for such adverse vibration cases, including the selection of delay times based on ground conditions, vibration frequency, and structural response. The Problem Research by the Bureau of Mines and others has demonstrated how structural response and the potential for cracking and other damage depends on blast vibration frequency in addition to particle velocity amplitude. The Bureau has published recommended criteria for blasting near low-rise residential-type structures; criteria that specified frequency-dependent amplitudes. The typical vibration frequency from surface mine and quarry blasting is 20 hertz (Hz). Sites have been found, however, that regularly produce ground-roll-type waves with frequencies as low as 4 Hz. The most serious cases arc those where vibration frequencies fall in the natural frequency range for structures of 4 to 12 Hz. Such vibrations have a higher potential for causing, damage to residential structures, particularly at the low end of this frequency range, because of the resulting high strains these frequencies produce in structural materials.

Jan 1, 1990

By Ronald D. Hill, Elmore C. Grim

Mining as an extractive process alone is outdated and unacceptable to today's environmentally concerned public. Multiple land use must be considered as well. Only through effective preplanning can the full potential of reclamation result in a lasting asset for future generations. The coal industry is now recognizing that reclamation of mined lands is part of the mining cycle that must be planned and carried out in a timely and orderly manner. It is also finding that planning reclamation in advance of mining is cheaper and more effective than waiting until mining is completed. The decision to open a strip mine must be based on the results of studies to determine if successful reclamation can be achieved and whether the economic benefits to the company will be justified(1). Information regarding the physical, chemical, hydrologic and biologic systems operative at the site must be under- stood or reclamation will be a failure. Working together, engineers, management and reclamation specialists should design the actual mining and reclamation plan before mining is begun.

Jan 1, 1974

Determine the extent to which remote-sensing techniques, primarily lineament analysis, can be used to identify geologic structures that may affect the location and migration of subsidence over abandoned underground coal mines in the Colorado Springs, CO, area. Compile data using a geographic information system (GIS) to allow efficient and reproducible comparisons and analyses. Background The basis for evaluating abandoned mine land (AML) sites with remote-sensing techniques comes from past and ongoing Bureau ground control research using remote-sensing data to identify potential hazards caused by geologic structures (faults, joints, etc.) above active underground coal mines. Research showed that lineament (linear feature) analysis of Landsat Multispectral Scanner (MSS) images could indicate locations of fractures and fracture trends that had varying, but significant, impacts on the stability of mine openings. Such geologic structures should be identifiable over abandoned mines as well. If fractures are present, even if they arc not faults, they should represent areas of potential instability over these mines and, therefore, should tend to localize subsidence when it occurs, particularly for deep and moderately deep portions of mines.

Jan 1, 1992

By William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to support the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

By David C. Oyler, Herbert H. Fields, William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to sup- port the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

By Dennis R. Dolinar, Lewis A. Martin

Cable bolt technology used by the U.S. coal industry was developed to a large extent in the 1990s. Today, these cable systems include both cable bolts and cable trusses to provide supplemental and secondary support in gate roads. This cable technology is significantly different than the cable systems in use in either U.S. hard-rock mines or Australian coal mines. Development of this technology was initiated and spurred by research efforts of the U.S. Bureau of Mines, and has continued under the health and safety programs of the National Institute for Occupational Safety and Health (NIOSH). It was also followed up by work of roof support manufacturers to create an essentially new support system. In this paper, the important support characteristics of both cable bolts and cable trusses are discussed. The design of cable systems and the basis for that design for tailgate and headgate situations are reviewed and explained. Case histories are presented on the application of these support systems based on experience gained at a number of in situ test sites.

Jan 10, 2000

By John Jordan, Steven J. Knoll, Douglas Tesarik, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004

By John Jordan, Tesarik, Steven J. Knoll, Theodore J. Williams, David K. Denton, Douglas F. Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because this condition can result in failures of ground that lead to both injuries and death. Personnel from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health studied two methods for identifying stress in rock. A seismic tomographic survey, finite-difference analysis, laboratory measurements of compression wave (ultrasonic) velocities in rock cores, and site geology were integrated to evaluate the use of seismic tomography for identifying induced pressures in an underground pillar at the Edgar Mine, Idaho Springs, CO. Electromagnetic (EM) emissions were also investigated in the Galena Mine, a deep underground mine in Idaho, in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results of this research indicated that (1) seismic tomography appears to be a useful tool for determining relative stress in underground pillars, while (2) EM emissions do not appear to be significant precursors of impending catastrophic ground failure.

Jan 1, 2004

By R. W. Stahl

Methane, a highly explosive gas evolved during the coal-formation process, is one of the hazards of mining most difficult to overcome. It is retained between particles of coal and entrapped in strata overlying and underlying the coal beds to a degree dependent upon the permeability of the enclosing strata. Considering that methane might be encountered at any time during the mining of coal, attempts have been made through the years to minimize the sources of ignition at coal-mine faces, such as the introduction of permissible electric equipment, the prohibition of smoking and open lights, and the development of safer explosives. The sparks created when mining-machine picks contact sandstone or iron pyrites2/ constitute one source of ignition, always recognized as a possibility but never greatly emphasized in the United States until recently, when ignitions began occurring with rather alarming frequency and in widely scattered coal-producing areas.

Jan 1, 1956

By G. W. Grove, H. R. Burdelsky, F. E. Griffith

"INTRODUCTION The work of using a system of air locks in unsealing a mine in Ohio following a fire probably was one of the outstanding jobs of its kind in a medium-thick coal bed.The fire in this mine, thought to have been of electrical origin, was discovered at about 1:30 a.m. on December 11, 1941. Forty-four men were working in the affected section at the time; 5 escaped unassisted, and 37, who had barricaded themselves, were rescued. The bodies of two men, who had succumbed after breathing fumes given off by the fire, were brought part way out of the mine before it became necessary to seal the mine.Direct attempts to extinguish the fire with water were abandoned when hazardous amounts of 'carbon monoxide, methane, and other inflammable gases were detected in return air passing through the main haulageway and escape-way of the mine.The mine was completely sealed on the surface at about 8 p.m. on December 12, 1941, with the two bodies remaining in the mine. Sixteen days after the mine had been sealed, the two bodies were recovered. This was accomplished by air-locking through a partitioned-off stairs compartment of a ventilation shaft. This work was done under adverse barometric and atmospheric conditions.A method for collecting representative air samples from the immediate fire area was used successfully by utilizing a vacuum pump on about 10,000 feet of existing water line that had been broken near the fire area.The immediate fire region was sealed, and confined to a relatively small area; the remainder of the mine was recovered, and operations were resumed February 9, 1942, or 59, days from the time of sealing the mine on the surface. This recovery was made by air-locking the main entries inby from the shaft and No. 2 right-face entries.The distance between air locks averaged about 500 feet, and as each new set of seal stoppings and air locks was completed, the old or outby seals were taken out and the area between was ventilated. In ventilating this area, it was often necessary to use line curtains to direct the air into dead-end places."

Oct 1, 1947

By Paris V. Brough

This paper, which describes the practice of milling custom ore, in addition to that produced under company and lease operations in the Tom Reed mines, is one of a series 'being prepared by the Bureau of Mines. ACKNOWLEDGMENT Acknowledgment is made to W. B. Phelps, managing director, and Jack Zwinge, superintendent, far permission to publish, a-ad to G. E. Jarpe, the present mill superintendent, for his assistance in preparing the paper. LOCATION The mill is in Oatman, adjacent to the Benjamin Harrison shaft of the Tom Reed Gold Mines Co., in the foothills on the western slope of the Black Mountains, western Mohave County. The railroad shipping point is Kingman, Ariz., 25 miles northeast of Oatman. Paved highway U. S. 66 passes by the mill. The altitude is approximately 2,700 feet.

Jan 1, 1937

By B. D. Hanson

An interactive computer program has been developed by the Bureau of Mines which enables the user to identify the effect of cutting system changes on relative dust generation for longwall shearer drums. The program simultaneously evaluates machine and coal seam parameters, and those parameters which the user can control. The user can change one or more of these parameters at a time to determine their effect on relative dust generation, cutting forces, and/or cost. The program is written in the BASIC programming language. A complete program listing is included along with user instructions and sample outputs. This program is a more comprehensive version of the relative dustiness index (REDI) program described in Bureau Report of Investigations 8979.

Jan 1, 1988

By J. P. May

This U.S. Bureau of Mines report identifies and evaluates factors responsible for dump-point accidents involving mobile mining equipment. Information regarding the occurrence and severity of the accidents, the industries affected, the types of equipment involved, the primary and contributing causes, and pertinent Federal regulations is included. The aim of this report is to provide information that will aid mine operators in the recognition of hazards associated with mobile equipment operation near the dump points of stockpiles and waste dumps.

Jan 1, 1990

By Henry E. Hilliard

The production, use, and emission of vanadium in the United States has been traced for the year 1991. Consumption was 3,300 tons2, exports 1,285 tons, and imports 2,013 tons. About 98% of production was used in metallurgy; the remainder was consumed in chemicals, including catalysts. Total emissions to the environment in 1991 were estimated at about 3,100 tons, including emissions due to the combustion of coal and petroleum products. Emissions resulting from the production of ferrovanadium were 130 tons, and emissions from the production of steel about 6 tons. Dissipative losses, defined as losses that occurred during use or as a result of wear, were estimated to be no more than 3 tons. Disposal losses were estimated to be about 4,600 tons. Most of these losses were steel products that contained 0.1% or less vanadium and mayor may not have been recycled. When these products are recycled by the steel industry, vanadium ends up in the steelmaking slag and does not return to vanadium use cycle. Worldwide emissions due to anthropogenic and natural sources were briefly reviewed. It was concluded that industrial emissions were about three times greater than emissions from natural sources.

Jan 1, 1994

By John L. Nieber

This information circular describes a computer program called VARSAT2D, a comprehensive unsaturated fluid flow simulator developed by the U.S. Bureau of Mines. VARSAT2D solves for either a vertical or horizontal, transient or steady-state solution in variably saturated, heterogeneous, anisotropic porous media using the Galerkin finite-element approach. Simplex triangular elements are used. Moisture retention characteristics are described by specifying either the Brooks and Corey, Brutsaert, or Van Genuchten power functions, with hysteresis described using the Maulem independent domain model. Boundary conditions may include any combination of time-varying seepage, pressure along solution domain, boundaries and/or at internal node points, unit hydraulic gradient at the lower boundary, and a uniform source and/or sink. This program should be a welcome addition for mining and environmental hydrologists, researchers, and engineers interested in modeling unsaturated fluid flow.

Jan 1, 1994

By R. S. Dean

The possibility of cheap electric power for a number of mining areas in this country has suggested to many the idea of electric smelting of nonferrous ores in small units at or near the mines. The electric smelting of nonferrous ores was tested fairly thoroughly 20 years ago by United States Bureau of Mines and by others, and the fact that it did not achieve continuing workable success in any instance is sufficient proof that it offered no advantages at that time.

Jan 1, 1937

By Lowell L. Patten

The Federal Bureau of Mines participated with the National Aeronautics and Space Administration and Martin Marietta Aerospace in developing, building, and testing a portable X-ray fluorescence spectrometer for use as an analyzer in mineral-resource investigative work. The prototype battery-powered spectrometer, measuring I1 by 12 by 5 inches and weighing only about 15 pounds, was designed specifically for field use. The spectrometer has two gas-proportional counters and two radioactive sources, 109Cd and 55Fe. Preliminary field and laboratory tests on rock specimens and rock pulps have demonstrated the capability of the spectrometer to detect 33 elements, to date. Characteristics of the system present some limitations, however, and further improvements are recommended.

Jan 1, 1982

By D. Randolph Berry

The U.S. Bureau of Mines awarded a contract to Foster-Miller Associates, Inc. (FMA) to provide recommendations on the safest, most practical methods for complying with new regulations requiring that all underground coal miners have a self-contained, self-rescuer (SCSR) -a device capable of supplying, in an emergency, 1 hr of self-contained oxygen (no breathing of mine air). This report develops information and recommendations which could be used during the early stages of nationwide compliance, especially in the areas of inspection, testing, and underground storage of SCSRs. Volume I contains an Executive Summary, Introduction, Definitions, Recommended Guidelines for District Managers and Mine Operators, and a Storage Plan Checklist and Sample Form.

Jan 1, 1981

By Richard L. Unger

The Bureau of Mines entered into a cooperative agreement with an eastern Kentucky coal mining company to comprehensively redesign the flow of equipment and supplies throughout its underground mines. Items were tracked from delivery to the warehouse and from surface storage areas to their final usage locations underground. Three underground mines were visited, and a great variety of tasks were videotaped for subsequent laboratory analysis. Of particular interest were tasks that required manual handling of the supplies or equipment components. Activities such as handling daily supplies (concrete blocks, rock dust, and cross- beams) and handling or lifting the continuous miner power cable were determined to be the most hazardous. Recommendations to the company included redesigned surface storage areas to facilitate the use of forklift vehicles to load the underground supply cars. Designs were also developed for different mechanical- assist devices to help in unloading the supply cars underground and to handle equipment maintenance tasks underground. Additionally, the videotapes of the underground manual handling tasks became the basis for simulating those activities in controlled laboratory conditions. This testing will contribute to developing guidelines for proper lifting techniques for low-seam coal mines.

Jan 1, 1986

By F. E. Block

The reaction between calcined dolomite and ferrosilicon has been studies with the aim of developing a continuous process for magnesium production. Small-scale tests were made in vacuum retorts similar to those used in the vacuum retort process as developed by Pidgeon (1)2/ and operated during the period of World War II in several Government-owned plants. Factors investigated with respect to the silicon efficiency were the reaction temperature, reaction time, amount of excess dolomite in the charge, and effect of adding sodium silicate to the charge to serve as a binder. Additional laboratory tests were made to study the reaction at elevated temperature but at atmospheric pressure. Silicon efficiencies exceeding 80 percent were found to result when operating in the temperature range from 1,750° to 1,800° C. for periods of 20 to 30 minutes.

Jan 1, 1956