Search Documents

By Erkan Bayrak, Serkan Erkara, Ozkan Duzgun, Ekin Gungor

This paper presents part of the outcomes of the drill and blast optimization project carried out at Kisladag Gold Mine in Turkey. Kisladag Gold Mine is the largest gold mine in Turkey with a low-grade, bulk-tonnage, open pit operation that uses heap leaching for gold recovery. After blasting, the ore is fed to a three-stage crushing circuit which prepares crushed ore approximately -10 mm (0.39 in) for heap leaching. Crusher downtime analysis showed that blocky material and insufficient feed are causing significant downtimes with the primary crusher. This was supported by the fragmentation data collected to date. It was decided to initiate a fragmentation project to understand the variation in the run-of-mine (ROM) size with a view to provide a consistent feed to the crushing circuit. The study includes the analyses of the ore strength and structure, image analysis of the fragmentation pictures acquired from blasts, blast auditing and quality assurance and quality control (QA/QC) analyses. During this project, over 200 fragmentation pictures were acquired from 47 blasts to optimize ore and waste blasts. Ore strength varies between 30 and 120 MPa and rock quality designation (RQD) ranges between 30 and 100. A site-specific fragmentation model was used to calibrate the fragmentation for blast domains formed. In addition, alternative cases were simulated to achieve blasts designs with consistent ROM fragmentation size distribution. Alternative blast designs that include stemming length and powder factor changes were suggested. Long stemming length, drill cuttings use, free faced blasts, small shot sizes and poor stemming length control were some of the key issues causing coarse fragmentation.

Jan 1, 2015

By A Bagchi, Nabiullah, Jagdieh

"A number of coal mines in India are affected by fire. Most of coking coal reserves in the country are located in Jharia coalfield where more than 18 sq. km is in the grip of fire. Generally such fires are confined in areas near to our crops. About 37 million tonnes of coking coal are lost in recent yearsdue to fire and another 48 million tonnes are blocked in fire areas. Preventive measures adopted to control fires were only partially successful and the cost of such measures was exorbitant I Temperature of blast holes in fire area varies between 60 and 300° C or even more. Even after thorough quenching of holes with water, it become difficult to bring down the temperature below SO"" C. For blasting hot holes primary need is to select safe and suitable commercial explosives and detonating fuse and to measure hot hole temperatures. VWiOUs types of commercially available explosives including Nitro Glycerine bare, slurries, site mixed slurries (SMS), emulsion5 ,detonating fuses and detonators were tested to determine their thermal behaviour at elevated temperatures under field simulated conditions in the Copyright © 2000 International Society of Explosives Engineers 1993g - Studies on Safe Blasting Technique in Fire Area of Coal Mines laboratory and in hot blast holes in field . More than 50 round of blast were conducted in fire areas. NG base compositions and detonators were found unsafe at temperature above SO0 C andtherefore, they are not permitted to be used in hot holes. Slurries and emulsion are stable upto 1200 c. For blasting at temperature exceeding SO0 C a heat resistant gel/ solution was developed by the authors and is being used in number of fire areas."

Jan 1, 1993

By Francisco Sena Leite, Pedro Brito, Gean Frank, PhD Soeiro de Carvalho, Jose, Vinicius Miranda

The consequences of rock blasting with explosives are directly related to the accuracy of drilling and, because they have an effect on fragmentation and ground level, they should be controlled to ensure a problem free production, increase work safety and reduce environment impact. Safety control is one of the most important processes in detonation, since it can compromise the worker security on site and, eventually, neighboring communities. Due to the technology advancements, it is possible to build a hole deviation control device with “of the shelf” parts, and for that reason the authors decided to evaluate the possibility of measuring hole deviation by creating a portable prototype using an electronic sensor capable of measuring the acceleration on objects, that is, to measure the own acceleration of a system, known as "accelerometer" and a micro-controller to handle and treat data. The main idea behind this paper is to validate the power of the Euler method, given the stepping limitations of the sensor and micro controller in order to reproduce of the hole shape. A case study was carried out, comparing the measurements of borehole deviations made by a traditional equipment and the prototype. A mobile application was also created in order to recover and treat and display the data to the user. For validation of the prototype, several holes were measured using the two devices. A residue analysis was used to validate the data obtained. After analyzing and confirming the effectiveness of the new equipment, the normality tests prove a symmetric distribution with null expected residual mean and minimum variance. Consequently, the accuracy of the prototype is evidenced. Thus, the authors aspire to emphasize the potential of using these sensors allied to a traditional numerical method for analysis of hole deviation.

Jan 1, 2019

By Douglas Rudenko

Have you ever had a neighbor complain about a blast one day, but says the next day’s blast was better, even though the Peak Particle Velocity (PPV) increased? How about neighbors that complain about a small trimming shot, but don’t complain about a big production shot? Have you ever reduced the pounds/delay and gotten more complaints ? Mine operators are often bewildered when trying to correlate blast design parameters to homeowner complaints. When complaints come, standard practice is to set up a seismograph in the neighbor’s yard to monitor the blast. Immediately after the blast, the neighbor usually reappears from the house wanting to know the seismograph reading. When told that the PPV was 0.1 in/set, well below damage levels, the homeowner explodes saying “Your machine is wrong”. Perhaps he is right. Understanding why people complain about blasting is not about PPV, it’s all about structural response. People could care less about how much the ground vibrates; they only care about how much their house vibrates. In this paper we will examine the primary factors that control structural response. Through the use of a large array of digital seismographs, the effects of two production blasts on a community surrounding a quarry are studied. The predicted structural response resulting from each blast is calculated at 175 seismograph locations. The predicted response is then correlated to previous research on human perceptibility to vibrations. The results of this analysis and correlation give a better understanding of what the residents actually feel in their homes. The detonations of two single-hole signature blasts are also recorded by the array of seismographs revealing the dynamic characteristics of the geology ‘surrounding the quarry. Once the influence of the geology was understood, blasts were configured to disrupt the natural rhythm of the site through the use of millisecond delays.

Jan 1, 2000

By Thierry Bernard, Pierre M. Vuillaume, Michel Kiszlo

"In the context of its studies for the trench ministry of the environment and for the French national coal board, INERIS (the French institute for the industrial environment and hazards, formerly CERCHAR) has made a complete critical survey of the methods generally used to reduce the levels of blastingvibrations."

Jan 1, 1996

By Robert Boehnke, Bernd Mueller

Despite enormous efforts over the last decades there are still many unanswered questions with respect to calculation and modeling of the blast process using appropriate physical laws. Most calculations of explosive charges of a blast design are based on experience, empirical observations or blasting theories with serious shortcomings. This paper presents a new theory for the design and calculation of a rock blast that is based on the momentum. It offers a clear-cut method for the calculation of blast processes. The theoretical results will be compared with on-site measurements by means of a newly developed strain sensor and further measuring equipment. The momentum theory helps better to explain physically the processes of a blast. On the basis of long-term statistical investigations a momentum balance can be carried out with the volume-based blasting momentum and the measurable momentum associated with the muckpile and the remaining rock mass. This type of consideration requires a complex procedure which includes the blastability of the rock masses. Realis tic strain measurements open a new interpretation possibility and judgment criteria for the most probable building damage, the dynamic impact on general types of buildings and also for the blast process itself. The blast-induced stress and the momentum generated could be back-calculated using a geophone profile and the strain sensor. The strain owing to a dynamic impact can be influenced by the changing of the drill-, blast- and shotfiring technique like the until now measured vibration velocity. In this way it is possible today to make a complex preparation, calculation and evaluation of blasts. The new techniques of measuring in connection with the momentum theory bring about an increase of the safety and a clearcut method of improving the blast processes. This procedure offers new possibilities for the precise calculation, simulation and modelling of blasts and resulting vibrations and leads to an increase of the safety as well as economic adaptation of the drill-, blast- and shotfiring techniques to a pre-determined blasting result.

Jan 1, 2003

By Sushil Bhandari, Amit Bhandari

Drilling and Blasting are core operations in a mine. They impact all the downstream operations and their costs. Digital technologies exist for optimizing both drilling and blasting for many years. However, these technologies have largely been non-integrated and non-real time. This gap results in sub-optimal drilling and blasting operations. Also traditionally focus has been on optimizing individual areas (drilling or blasting and subsequent subsystems). Industry has largely lacked real time or near real time integration available to the user in the field and in the office. In this paper, a case study is presented of a large global cement company using a cloud and mobile based platform across 17 of their mines consistently over a large number of users over a period of over two years. The use of a blast platform is detailed which include blast designs, blast data collection and the trends in terms of results. On the drilling side, this paper describes the ability to capture drill logs, plod reports etc. Also actual drilling information in the field using a mobile device and its real time synchronization with a blast designer to provide visibility of expected fragmentation and vibration levels based on the drilling done. Key parameters such as hole ID, design depth, actual depth, hole status, designed and actual charge (length and weight), designed and actual stemming length are captured. The case study also highlights the challenges in technology adoption and implementation in mining in drilling and blasting. Making drill and blast results predictable should be the desired direction. Also digital technology tool adoption has been seen at the biggest miners – not so much in mid-sized miners or drill and blast contractors. Benefits of this platform on the safety side are highlighted including predictions on safety parameters and appropriate alerts if blast safety parameter / clearance zones are not met. The safety parameters are made available visually to the operator using maps and / or on drone images. Future possible improvements in the digital technology platform at the site are also highlighted including greater possible automation.

By Jason Ryan, Stephen Harria

Q.E.D. (QED) is a blast design and evaluation model that allows full three-dimensional design specification including the development of unique “live” terrains and an unlimited variety of complex charge configurations. QED’s analysis package allows the examination of likely outcomes resulting from changing various design variables in terms of vibration, fragmentation, rock-mass damage and muck-pile profile. Especially applicable to use cautious blasting applications, QED’s damage model uses vibration to estimate rock damage beyond excavation boundaries. This relates directly to operations such as Yucca Mountain Nuclear Waste Repository in Nevada, where damage beyond the excavation perimeter must be tightly controlled. The U.S. Department of Energy (DOE) h as b een studying a site at Yucca Mountain, NV to determine its suitability for long term storage of nuclear waste. The main mechanism of waste isolation will be the natural barrier of the host rock Total Systems Performance Assessment (ISPA) is used to model the excavation design and its behavior over time. Of importance to TSPA is quantifying the condition of the rock-mass before and after excavation. Ideally, there should be no excavation-induced changes to the rock-mass’ structure (removing the requirement to model the effects). At the least it may be possible to keep excavation-induced damage far enough away from waste packages so that modeling of these effects will not be required. QED can calculate a prediction of the extents of blast induced damage to the rock-mass. By using this metric as a design parameter, it may be possible to complete excavation of the repository more rapidly and inexpensively than previously thought, without jeopardizing the structural integrity of the waste containment areas or requiring blast damage to be modeled by the TSPA. This paper will explain the structure of the QED blast modeling system and show the analysis of historical data from Yucca Mountain. Processing of the historical data and the subsequent results will demonstrate how blast modeling can be used on an ongoing basis to assist the excavation process at Yucca Mountain.

Jan 1, 2000

By R. F. Favreau, Patrice Favreau

"A blast with explosives creates vibration waves in the zone around the blast.The prediction of the intensity of vibrations is important because people in the cinity demand that the vibrations do not disturb them, and society imposes limits on the vibrations. The U. S. Bureau of Mines (USBM) showed that the easurement of the particle velocity U predicts the risk of damage from vibrations. A currentapproach of blasters to monitor vibrations is to measure them with a seismograph at several distances S, and create a graph of U vs. S and the explosive charge “W” according to the equation U = K / (S / W)N where K and N are constants that depend on the blast method and the nature of the ground over the distance S. Though useful, this equation is empirical, and the results predicted from it are very variable, as shown by figure 1 which indicates that a prediction of U can deviate significantly from the actual value. Moreover, a minimum of two seismograph measurements at two values of S are required to establish the curve. However, here now exists another very convenient method to predict U; it is with the simulator Vibmas, which is based on the fundamental principles of how a blast reates vibrations. This simulator takes into account not only W but rather all the blast parameters, the type of explosive and the properties of the rock. Moreover, to establish the calculation of U as a function of S, only one seismograph measurement is required rather than two as for the USBM method. This last difference is important because it makes it easy to predict U not only as a function of S, but also as a function of the orientation of S. On the site this allows much safer control of the vibrations, and the use of larger explosive charges which reduce excavation costs. The article presents results from a field case at a hydroelectric project in Canada, where the deviation was very moderate. Use of this vibration simulator on the Web is very easy."

Jan 1, 2015

By W. J. Birch, D. Leckenby, R. Farnfield

The use of electronic detonators to improve fragmentation is becoming universally accepted. However their use in limiting peak particle vibrations levels is still in its infancy. Most of which is anecdotal, in that few actual scientific studies have been carried and published. This paper details the research work carried out at a limestone quarry in the County of North Yorkshire in Northern England. Here a series of blasts were carried out some used non-electric detonators whilst others used electronic detonators. The majority of blasts were carried out at the same burden, spacing and deck charge weight loadings. Initially, the key variable was the difference in detonator type and then leading on to using the electronic detonators at specific exact different detonator timing intervals. Later the study was extended to include double row as well as single row blasts.

Jan 1, 2007

By Hans Perlid

In the handling of emulsion explosives pumping is a key operation. A number of serious accidents has shown that pumping can be a risky operation and should be carefully considered and investigated. This is the background behind a series of pump tests carried out by NITRO NOBEL.

Jan 1, 1996

By Robert Lee, Jeff Corace, Rob Cyr

Blasting in the heart of the historic Byward Market District of Canada’s capital, Ottawa, presents a unique set of challenges. The obvious difficulties arising on projects requiring blasting within 3 m (10 ft) of 125 year old buildings in various states of disrepair have been encountered and successfully dealt with countless times before. The complexities increase exponentially when tenuous property boundaries, unknown structural details, litigious histories and the need for encroachment agreements lead to individuals with competing interests all able to impact the same operation. Blasting on three projects in the Market was started in early 2005 after months of negotiation. Ultimately, the potential for the projects to proceed hinged on the ability to successfully disseminate blast data to the various stakeholders. As part of the agreements drawn up, property owners demanded immediate notification of the measured vibration levels with contract provisions including clauses such that any exceedance of the USBM criteria immediately triggered project shut down and complete blasting program redesign, and approval by all parties. With stakeholders located in various cities and, in some instances, on various continents, a conventional attended monitoring strategy would not satisfy the requirements. In response to the critical reporting need, Explotech Engineering Ltd. installed unattended monitoring stations around the sites, all incorporating wireless telemetry. After each blast, data was automatically transferred from the monitoring stations to a web-linked server via the wireless network, where it was immediately available to project stakeholders through a password protected website. The solution required a unique blend of data acquisition, telemetry, database, and security technologies, all married to produce a reliable system that was easy to maintain and use. While these types of systems were originally developed for use as permanent monitoring networks in operating mines and quarries, monitoring professionals are increasingly benefiting from the technology on temporary building projects that have typically been the realm of attended monitoring strategies. Globally, this has emerged as a solution to provide more timely access to data for stakeholders, and to minimize the legal exposure from multiple violations of vibration limits. As this trend is likely to continue, the regulated vibration control industry is likely to see a continued shift in technology development to leverage wireless networks and the Internet to continue to improve data transfer, archiving and distribution.

Jan 1, 2006

By J Lyall Workman, Peter N. Calder

"Large hole rotary drilling is one of the most common methods of producing blastholes in open pitmining. Large hole drilling generally refers to diameters from 9 to 17 inch (229 to 432 mm), however aconsiderable amount of rotary drilling is done in diameters from. 6% to 9 inch (165 to 229 mm). Thesesmaller diameters are especially prevalent in gold mining and quarrying."

Jan 1, 1996

By Sarma S. Kanchibotla

In overburden cast blasting the explosive energy is used to move a significant percentage of overburden from the high wall to the spoil pile thus reducing the amount of material to be handled by machinery. However, the obvious trade-off between the extra explosive energy in the cast blast versus reduced dragline effort is complicated by an increased risk of damage to the underlying coal. This damage may not be obvious but inevitably leads to reduced coal recovery and may negate much of the benefit sought from cast blasting.

Jan 1, 1999

By Jerry Wallace

This project consisted of blasting for expansion of a major interstate natural gas transmission pipeline pump station. The pump station handled 400-500 million cubic feet (1 l- 14 million cubic meters) of gas per day.

Jan 1, 1996

By Kameron Ray, Ruilin Yang

This paper compares the modeling results obtained by using a single seed waveform (SS) versus multiple seed waveforms (MS) as inputs to the Multiple Seed Waveform (MSW) blast vibration model. The field data for the comparison was collected at a coal mine. The results of the comparison showed that the MSW model yields more accurate predictions and significantly higher correlation to field measurement when using MS as input. When using a single seed waveform as input, different seed waves result in different predictions of PPV. In contrast, using the multiple seed waveforms as an input, more consistent results are obtained.

Jan 1, 2013

By Jena Moshen

Underground Bulk Systems (UBS) technology has gained widespread application in tunneling and underground mining owing to its safety, reliability, increased Velocity of Detonation (VOD) and excellent results. However, its application in perimeter blasting is still limited and researchers are looking at ways of harnessing this technology for perimeter control. This simplifies the charging process by using one cost efficient product for charging both the perimeter and grid holes. This paper presents a case study on the application of underground bulk emulsion explosives for perimeter control blasting in underground room and pillar platinum mines. In order to achieve the required coupling ratios in the perimeter holes, the emulsion is loaded into specially formulated smaller diameter polyethylene (poly) pipes. The effectiveness of this method was evaluated using information obtained during routine blast audits and data supplied by the mines on half cast factors, over break and under break as well as analysis of data from Ground Penetrating Radar (GPR) Scans over a period of four years. This method of perimeter control, has given the platinum miners in Zimbabwe a competitive edge in cost effective perimeter charging and blasting by simplifying the previously costly deployment of traditional barrels and other decoupled cartridges. The method has been adopted by all the platinum mines in Zimbabwe as it has proven to be a cost effective alternative of controlling the perimeter walls, along with other key benefits that relate to safety, productivity and effectiveness.

Jan 1, 2018

By Ron Frye, Carl Liibbe, Wayne Curtis, Julie Pecori, Dan Leach

Test work comparing the performance of a Low Density Porous Ammonium Nitrate Prill to regular Porous Ammonium Nitrate conducted in Pennsylvania and New York showed that less ammonium nitrate was required to perform the same work and that improved sensitization of an emulsion/ammonium nitrate blend reduced “orange fumes”. Fragmentation was similar in all tests with improved heave and throw experienced.

Jan 1, 1997

By L. Trivino

Blast-induced damage criterion based on the peak particle velocity has worked reasonably well for estimating building damage. However, the same criterion cannot be used to estimate damage to rock and mine structures such as shaft and tunnel walls. It does not take into account the nature of seismic radiation pattern in the near-field, which is very different than what is obtained at far-off distances. To investigate this phenomenon, a systematic study has been carried out involving single-hole blasts and normal production blasts, with explosive source ranging from nearly point source charges to standard borehole sizes (6-7 m long explosive column), with charge weight varying from 0.5 kg to 30 kg. In the near-field, it is shown that, both P-wave and S-wave take a dominant position compared to the mainly surface waves measured in the far-field. These are shown to depend strongly not only on the length of the explosive column but also the way it is initiated in the borehole (i.e. direct vs. reverse initiation in the borehole) with respect to the target location. The seismic radiation patterns were recorded by high-frequency triaxial accelerometer stations grouted in the rock mass. This study describes the nature of seismic radiation in the near-field from long and short charges, the role of initiation direction and their effect on frequency with respect to sensor locations or target area of interest, and their implication in prediction of blast-induced damage in the near field.

Jan 1, 2009

By Jean-Sébastien Lambert, Serge Roberge

"At the end of 2014, Holcim Canada (Demix Aggregates Division) considered the possibility of drillingand blasting a big volume of rock in order to expose a high-quality limestone bench in one of their urbanarea quarries in Laval, Quebec (Canada). The project includes many challenges and has thus been qualified as a high-risk operation."

Jan 1, 2016