Search Documents

By Fearnsides W. G.

The second part of the paper, presented at the Midland Institute of Mining, Civil and Mechanical Engineers' general meeting held in Doncaster on 27th May 1916, addresses the post-Carboniferous and pre-Permian movements which brought about the partition of the area and gave to the North Midland district its individuality as a separate coalfield. As earth-movements of several ages subsequent to the Carboniferous have played a part in the formation of this particular coalfield, the aim is to elucidate the effects which belong to the post-Carboniferous and pre-Permian Period and to disentangle them from those of later date. This is done by comparing the geometry of the folded surface of one of the more important horizons in the Coal-Measures with that of the surface of unconformity which divides the Permian from the Carboniferous rocks in South Yorkshire, Derbyshire, and Nottinghamshire

Dec 1, 1916

By W. R. Chambers

A wide variety of mining conditions exists within the South Midlands Area and across this range of conditions more than one half of the mines are highly susceptible to spontaneous combustion. Two thick seams in which the greatest risk exists are described and illustrated. The different heatings which take place are categorized by the locations at which they occur in the mines: additional special cases not easily categorized by location are discussed separately. The discussion for each category of heating follows the pattern of: (i) the reasons why it occurs; (ii) when it arises the means by which it is fought, and (iii) the preventive measures taken in an attempt to avoid its occurrence. Relatively new factors which may affect the incidence of heatings are highlighted and suggestions are made which may assist in reducing the number of incidents in the Area. A new method of continuous sampling, analysis and recording is described and mention made of an original method of interpreting carbon monoxide results with the aid of the computer. The first results from this work show that an early warning is given of an adverse change in trend several weeks earlier than with the present methods. Lastly, suggestions are made about the direction in which research might proceed to assist in reducing the special hazards created by several features inherent in the present methods of mining.

May 23, 1905

By I. R. Hanby

A simple but comprehensive method has been developed for the simulation of a mechanical-drive dump truck that enables various parameters to be predicted as a function of time throughout its whole cycle. Uses of the simulation results are indicated with specific attention to environmental and operational or economic planning. The output of a sample run is presented. The method can be easily adapted for the investigation of a wide variety of mobile plants.

Jan 4, 1992

By J. C. Loretto

The philosophy and detail of mill design in developing countries, where it is frequently difficult to obtain experienced, qualified supervision to operate the plant, are discussed. The resulting design suggests the desirability of simple units, with maximum visibility of equipment operation and material movement, which allow the minimal technical supervision to see the plant conditions prevailing. Information on plant conditions during periods of lesser supervision can be provided by the use of simple, low-maintenance recorders. Where the mill is intended for operation in a developing country, it is insufficient for the flowsheets and plant layouts merely to be drawn: the process metallurgist must pay meticulous attention to details that could ordinarily be left to the design detailing group. The design of this type of mill requires a knowledge of human engineering—of the type of individual who will operate and supervise the plant; probable changes in personnel should be taken into account. Details are suggested for coarse-ore handling, screens, feeders, secondary and tertiary crushers, conveyors, dust collecting, fine-ore feeding, grinding mills, conditioners, flotation, thickeners, filters, reagent systems, sand pumping, sampling, instrumentation, safety and construction

Dec 1, 1971

By C. J. V. Wheatley

Recent studies of the mineralisation at Avoca in southeast Ireland, Parys Mountain in Anglesey, and Coniston in the Lake District result in the proposal of a new metallogenetic model for mineral deposits in the Southern Caledonides. A regional pattern of metal zoning exists, an axial belt, including the major copper deposits, being bordered by areas with lead-zinc deposits. Conformable lenticular pyritic zones occur in the central belt, closely associated with acid volcanic sequences and, often, post-dating them. These zones are thought to have been formed in a marine environment, mineral growth taking place below the sediment-water interface, whereas magnetite-rich zones developed under different Eh and pH conditions. Stockworks containing appreciable copper and, in some cases, lead and zinc were developed at a later date, stratigraphically below the pyritic zones, by migrating hydrothermal chloride and metal-rich fluids. Complex lead-zinc-pyrite mineralisation resulted from the reaction between pyritic zones and the final fraction of the hydrothermal fluids. Crosscutting vein-type fissure infilling mineralisation occurs in every mineral field. These deposits apparently comprise a pulsatory metasomatic sequence, closely related to tectono-stratigraphic controls, ore localisation being influenced by the coincidence of suitable structures and pyritic shale horizons. The implications for mineral exploration are considered and it is concluded that the model offers an explanation for the existing pattern of metal zoning; and it may have wide applicability to mineral deposition in geosynclinal sequences.

Dec 1, 1971

By S. Vardy

The paper notes that the extraction of 22% of the remaining workable reserves in the north western area involves a risk of spontaneous combustion higher than is normal in Britain. Mining systems have been tailor made in order to minimize the risk of spontaneous heatings, and these systems are described. Well-proved methods of combating spontaneous combustion are referred to, as well as the limitations which now apply to them as the result of the introduction of modern mining techniques. A substantial part of the paper is devoted to the circumstances in which spontaneous combustion occurs underground in the north western area. Several actual incidents which have occurred in the last few years, along with the practical application of the lessons learned, are described. Of particular note are: a) the procedure adopted in the north western area to equalize pressure differences across stoppings using pressure chambers, and b) a retreat mining system, primarily designed to deal with high methane emission and steep gradients, which also affords some protection against spontaneous combustion.

May 23, 1905

By T. F. Bamber

The South Nottinghamshire Area has not been greatly troubled by spontaneous combustion until the last few years, during which the Blackshale Seam has been developed and exploited. The problem was first encountered at a colliery which was heavily preoccupied with a major reconstruction scheme, and with the sudden appearance of a completely new hazard both men and management had to adapt themselves very quickly to meet the situation. The paper contributed to the Symposium by the South Nottinghamshire Area illustrates the problems by reference to actual incidents, and shows how the lessons learned from them have been applied to the shaping of future policy on the avoidance and treatment of spontaneous combustion.

May 23, 1905

By A. Z. Lang, D. A. Hall

After a brief description of the causes of spontaneous heating and of general preventative methods, a detailed account is given of occurrences of spontaneous heating in the Main Seam (locally known as the 5/4 Seam) at Westoe Colliery. This seam is about 12 feet thick consisting of hands of coal and shale, but only 4 feet 6 inches is worked because of the thickness os strata in water-bearing rocks and the worked section is selected on quality considerations. An advancing longwall face in this seam (2nd South) began to heat after working for six months and ultimately had to be abandoned. By adopting retreating methods and mining narrow panels it has been possible to extract this coal at an excellent rate of productivity. The system of goaf ventilation is important, because the use of a bleed road would have given rise to dangerous conditions in a goaf which of necessity would have contained fallen coal. Preparatory seals were prepared at selected sites so that, if necessary, a panel could be sealed off quickly; these seals are completed as soon as possible (within three weeks) of finishing a panel. A gas sampling system has been instituted which includes daily sampling on the face and in the goaf, and weekly sampling at the stoppings of all completed panels. The coal has now been extracted from this seam for three years without any further difficulties from spontaneous heating.

May 23, 1905

By C. J. Kirkland

25th Julius Wernher memorial lecture given at Tunnelling '91, sixth international tunnelling symposium held in London, 14-18 April 1991. The title gives the lecturer a chance to share some of the lessons he has learnt in a lifetime of tunnelling and particularly in the last six years of his involvement with the Channel Tunnel and the International Tunnelling Association. These included: the difficulties of split contracts but the problems arising with Eurotunnel over the need to create a single owner to whom the banks could lend; the peripatetic nature of tunnellers who built London's underground in the 1960s and returned to build the Channel Tunnel from Egypt, Singapore, Hong Kong and Australia; the increasing requirement for strategic planning resulting in tunnels between European countries and the need for engineers to deal with decision-makers; EU work on harmonising regulations so that there need no longer be, for example, arguments over which regulations should be followed for temporary electrical equipment in the section of the UK tunnel that is technically in France; the huge improvements in safety standards and attitudes; the enormous increase in the scale of undertakings and individual contracts, with an accompanying change in attitudes to logistics; technological advances to cater for the high performance now required of equipment; and the rising importance of environmental issues. The lecturer also briefly touches on the work of the International Tunnelling Association

Jun 13, 1905

By NA NA

Reports of discussion at sessions held in Keyworth, UK, on 22-23 April 1992.

Jan 12, 1992

By International geochemical

During the production of the Geochemical Atlas of Finland till samples were collected throughout Finland at a density of one sample per 300 km2. The material studied was the fine fraction of till (less than 0.06 mm). The geochemical mapping has shown that elements that are locally enriched in bedrock in the form of ore mineralisation are also enriched in a wide area of the surrounding till. These anomalous enrichments of ore elements take the form of rectangular or curvilinear zones that are some tens of kilometres wide and hundreds of kilometres long. The mineralised zones host ore deposits of different genetic types and can be termed "ore provinces". They stand out prominently on the geochemical maps and can be divided into sub-units of different chemical composition.

Jan 12, 1992

By W. R. Donaghue, R. L. Robinson, C. Scott

Whilst spontaneous combustion has never been considered a major problem in south Durham, certain collieries in the area have a history of heatings and precautions are essential. Three collieries are affected - Shotton, Vane Tempest and Seaham - and in the case of the last two, there are huge areas of high quality coal to work under conditions where spontaneous combustion is a real hazard. The seam being extracted has an immediate roof in goaf left by the incomplete extraction of a contiguous seam worked before the turn of the century. The presence of residual coal stocks and old roadways and cavities adds to the difficulty of preventing unwanted air movement. The main preventive measures adopted are the construction of airtight gateside packs and the use of sprayed surface coatings in the gate. Sampling systems and sampling points are described and, in particular the field of continuous monitoring from the surface is examined. The resulting possibility of a quantitative as well as qualitative assessment of the preventative measures required is discussed.

May 23, 1905

By M. Riddell

This paper describes the incipient heatings that occurred below ground in the High Main and Main seams at the mine between the years 1963 and 1966. The possible causes, effects and activities associated with such heatings are discussed in an attempt to establish the precautions necessary to minimize such occurrences. The assessment of as many "norms" as possible is made to enable the earliest detection and level of activity to be determined.

May 23, 1905

By R. R. Hart, R. A. Evans

This paper outlines the the methods currently being used in the West Wales Area for preventing the occurrence of any outbreak of spontaneous combustion. Stress is placed on the importance of correlating the position of a Rider Seam which is prone to spontaneous combustion. The recent introduction of the UNOR Recorder has contributed to the ability to monitor the CO content of the general body of the air during any incident. The use of modern sealants and improved methods of applying them have enabled the few instances of spontaneous combustion in South Wales to be treated promptly and efficiently. The authors describe the current spontaneous combustion problems at two collieries.

May 23, 1905

By T R. Marrero, J W. Wilson

This paper presents costs for a coal log pipeline that can transport coal over distances from 50 km to 1500 km. The coal log pipeline (CLP) concept is a new technology in w hich coal is compacted into water impermeable circular cylinders that can be suspended in water flowing through an underground pipe. CLP includes processes to prepare the run-of-mine coal for compaction, the injection of coal logs into a pressurised water-lilled pipeline, the conveyance of the coal through a pipe including special pumping stations, and the treatment of the coal logs and water at the pipeline outlet. An 8 inch (203 mm) pipeline can transport more than 2 Ml of coal per year. CLP components have been extensively tested in bench-scale facilities where these tests have included start up/shutdown steady state flow behaviour, end of pipeline treatment of water and coal log handling, water hammer effects, abrasion of logs and pipeline, coal log manufacture, and other engineering operations. Several sites are being considered in the United States (US) for the first commercial demonstration that will probably take place in 1998. The cost calculations are based on realistic values for all the components of a CLP. including a return on investment. For pipelines of different diameter, values for coal transportation are presented in terms of $(USVtonne as a function of distance.

Jan 10, 1996

By J. D. G. Groom

The introduction to a selection of papers from the Minerals '98 professionals' conference, held in London, 24 June 1998 as part of a week of activities supported by 13 professional and trade associations to promote the industry, highlights enthusiastic visitor comments on quarry visits around the UK and outlines the Foresight programme whose key issues were addressed at the conference

Jun 21, 1905

By R. D. Stewart

Paper presented at the conference: Risk assessment in the extractive industries, held in Exeter, UK, 23-24 March 1994, and first published London: IMM, 1994, preprint volume, 18pp., 5 refs. A seismic risk assessment method has been developed for application to rockburst prone deep-level mining sites which have sufficient seismic coverage. The technique utilises several seismic hazard parameters simultaneously and assesses the seismic risk on a daily basis according to the individual levels of these parameters. Critical levels are determined from investigation of the long-term behaviour of the parameters in relation to recorded potentially damaging seismic events. The method has been applied to a data set comprising 15 months' worth of seismic data, with encouraging results

Aug 1, 1995

By J A. Hacked

This paper explores the potential to exploit controls over the outputs of the primary blasting operation, arising from the performance consistency benefits gained in using modern bulk emulsion explosives technology. The former, allied with the latest powerful blast predictive software and measuring tools, offers the user the opportunity to apply control over both cost and performance, which has not been possible in the past.

Jan 12, 1997

By R. N. Pryor, S. H. Shaw, D. L. Dowie, S. H. U. Bowie, M. J. Cahalan, S. F. Gandar

It is concluded that land-based mineral resources will be adequate for most minerals in the immediate future, but in the long term more minerals will come from offshore locations. Because the oceans are international and can transport pollution, international control of offshore workings will be necessary. In the UK and similarly highly developed areas, the working of low-value bulk minerals will create increasing problems in urban development and countryside preservation. Much more information should be published on standards to be adopted and their costs, if emotional social pressures founded on ignorance are to be avoided. The Town and Country Planning Acts have greatly improved the environmental quality in Britain in relation to mineral working. In the long term conservation of some minerals in short supply may be necessary on a national or international basis. Much research is required for the determination of adequate criteria and standards for the preservation of environmental quality in the mineral industry. New local, national and international legislation will be required and the adoption of voluntary standards by trade associations should be encouraged wherever appropriate

Dec 1, 1971

The following procedure was used to determine cut-off grades: define the orebody profile; plan the stope layout and quantify the work involved; formulate equipment-performance norms; calculate unit costs; input process recoveries and metal prices; and calculate the cut-off grade. Use of the method is illustrated using data from a copper mining complex in India. Results from the study led to the following conclusions for underground mines in general. Cut-off dependent costs vary significantly with the stoping method employed, orebody thickness, the degree of mechanisation and the working efficiencies of the workforce and equipment. This applies even within the same deposit. Sub-level stoping and its variants can be operated at a lower cut-off grade than cut-and-fill and its variants. Thinner orebodies affect cut-off grades adversely, but with thinner orebodies very little further reduction in cut-off grade can be achieved once a certain minimum width has been exceeded. For the same stoping method and in the same mine the cut-off grade varies with the degree of mechanisation. Labour-intensive methods require higher cut-off grades. An allowance for working efficiency should be made when calculating cut-off grades. Higher process recoveries allow a significant lowering of cut-off grades

Jul 1, 1996