Search Documents

By Antonio A. Cristóvão, Alexandre Pinto

"Abstract Deep foundations of buildings using driven ductile iron micropiles TRIM solutions, leads to recognized advantages, from technical, schedule and economic points of view. High production rates together with the possibility of using conventional equipment, duly adapted, confer this solution a high versatility.The aim of this paper is to describe the main design criteria adopted for the foundations of the Church ""Nossa Senhora dos Navegantes"" building in Lisbon - Portugal. In addition, results of a full scale load test carried out at site are presented, confirming the adequacy of the solution to the geological and geotechnical scenario, which is characterized by the proximity of the Tagus River Basin as well as the presence of heterogeneous landfill material and alluvial layers of soft clay (muds).1. INTRODUCTION Located on the right bank of the Tagus River, in Lisbon, the new Church building of ""Nossa Senhora dos Navegantes"", patroness of fisherman and navigators, with three or four upper floors, is surrounded by a school and by new residential buildings.The Tagus River basin is known by its alluvial soft soils, achieving, in certain areas, more than 50m meters depth, challenging the construction of new facilities due to the significant unfavorable geotechnical conditions.With a modern an unusual architecture, allusive to the ships used by the Portuguese navigators, the building has a reinforced concrete structure, with one basement and three upper floors. A bell tower with about 40m high, emerging from the structure, marks the landscape with the presence of this religious building (figure 2).For all the reasons previously described, geotechnical engineers play a crucial role on the design of valid foundation solutions, from both technical and economic point of view. Ideally, the solutions adopted should be supported by full scale load tests, performed at site, so that design assumptions could be verified and adjusted on time."

Jan 1, 2014

By Patrick Granitzki, Alicia Plinio, Janitha Batagoda, Peter Howell

The City of Newark is making a comeback with new mixed-use multi-storied Residential Development projects. The majority of developers tend to use driven H-pile deep foundation systems to support their super-structures. A different approach was recommended for one particular new development near the Passaic River. The surficial geology included glacial deposits consisting of loose to dense sand overlaying relatively soft silt and clay and a lower stratum of medium-dense sand. During a preliminary site investigation for the project, bedrock was encountered at depths ranging between approximately 168 feet to 182 feet below the ground surface. Design capacity required a single pile of 200 tons. Two different pile foundation systems were evaluated in conjunction to the typical driven H-pile system in order to review potential costs and construction schedule impacts. The two alternative pile systems evaluated were tapered tube piles and drilled displacement piles. Theoretical calculations were followed by in-situ load testing. The field testing results indicated the use of drilled displacement piles as the best option for a portion of the proposed building. This paper discusses the different piles systems considered, installation and using drilled displacement piles to minimize cost and optimize construction.

Sep 8, 2021

By Bernard Hertlein, Chia K. Tan

"The move to LRFD methods for structural design by AASHTO, ACI, AISC , ASCE, and the FHWA has been a major change for the American construction industry. The deep foundations industry has arguably been placed most at risk by this situation, because of the need for, and the difficulty of providing, reliable quality assurance.LRFD is attractive for both the owner and the engineer because it promises cost reductions, but the assumption underlying LRFD is often overlooked - that the acceptable margin of safety can be rationally reduced, thus saving costs, provided that all the factors involved are closely controlled. This means that both the quality of the materials and the quality of the construction work must be closely monitored, and held to an acceptable standard.This paper describes the type of comprehensive quality management program that is needed in deep foundation construction projects based on LRFD. Case histories are used to illustrate the importance of both adequate inspection and reliable testing to a comprehensive quality management program.IntroductionOver the last thirty years, the major organizations that set standards and practice policies for the American construction industry, such as the American Association of State Highway and Transportation officials (AASHTO), the American Concrete Institute (ACI) , The American Institute for Steel Construction (AISC), the American Society of Civil Engineers (ASCE), and the Federal Highway Administration (FHWA), have embraced Load and Resistance Factor Design (LRFD) as an alternative to, and in some cases, a complete replacement for, Allowable Stress Design (ASD). AASHTO first published a new set of LRFD-based design guidelines for bridges in 1996, with several revisions in 1997, 1998, and 1999 (AASHTO, 1996). The 1996 AASHTO Bridge Design Code was the first in the United States that required foundations to be designed using LRFD procedures. LRFD has a clear advantage over conventional ASD where variability in material strength, bias in design methodology, and degree of construction quality can be rationally accounted for to achieve an acceptable level of risk."

Jan 1, 2005

By Rick Deschamps

A reoccurring problem with support of excavations in urban areas involves the placement of external support components like anchors or nails in right-a-ways, subway and utility setbacks, in areas occupied by adjacent structures, and within the property of non cooperative neighbors. Such a situation occurred for a project in Arlington, Virginia, which ultimately resulted in the preliminary design of a large footing supported cantilever retaining wall that was extremely costly and impractical to build. An innovative design alternate consisting of a series of vertical concrete elements (VCEs) supported by post tensioned tiedowns was proposed to the General Contractor and accepted by the owner. The VCEs were designed to serve as the main structural elements for both the temporary support of excavation system and the permanent wall. The VCE?s were constructed using single bite diaphragm wall panels oriented perpendicular to the excavation face including a rebar cage and tremie concrete. Threaded inserts were placed within the rebar cage to attach the cast in place exterior wall. Overall stability and lateral movement of the VCEs were controlled by high capacity vertical anchors embedded within the VCE. A detailed instrumentation program was installed to monitor the movements of the VCEs with relation to the excavation depth. The paper present the project case history by discussing the design concepts of the VCE, the construction approaches used to install them, the construction challenges encountered, and the performance of the unique system.

Jan 1, 2008

By Babu K. V., Samyukta P.

The energy demand in India is expected to show increasing growth in the next few decades. The oil companies in India are revamping the existing oil refineries as well as constructing new refineries across the country to meet the energy demands. Most of the refineries in India are located along the coastal region because of the ease of transporting crude materials. Considering the criticality of the structures as well as soil conditions in the coastal region, pile foundations are used in refinery plants. In India, non-displacement piles in the form of bored cast-in-situ piles are used to support structures. In a few circumstances, displacement piles in the form of driven cast-in-situ piles are also being used to support critical structures. This study presents the performance of non-displacement and displacement piles for similar ground conditions at the same project location. The pile load test results have shown that the settlement observed for displacement piles is lower than compared to non- displacement piles for a given loading and soil conditions. This shows that the performance of displacement piles is slightly better in comparison with that of non-displacement piles.

Sep 1, 2022

By Vijaya Bhushan Rao, Ali Semercioglu, Jason Redgers

Large diameter steel water tanks with high storage capacities impart heavy loads deep into the ground, generally requiring deep foundations to adequately support them. The use of ground improvement as a sustainable and cost effective alternative is tempting but the design of the foundations for such heavily loaded, thin-shelled structures have to meet several performance requirements such as bearing capacity, limiting the specified total settlements, typically limiting the radial differential settlement to 13mm over 10m along the circumference and dishing settlement from edge to center of 1/120 as per standard API 650 Appendix B as well as the mitigation of liquefaction induced settlement risk. Any inadequacy in the soil investigation, geotechnical design, or misrepresentation of stresses of the foundations may lead to serviceability compromise or potentially catastrophic failures. Therefore, the selection of the foundation is dependent on the availability of suitable ground report and the limitations imposed by operational requirements. Two such case studies are evaluated and compared in this paper, with tank diameters ranging from 41 to 106m in the Kingdom of Saudi Arabia, (KSA) which were founded on two types of soils and supported on deep foundations i.e., stone columns and bored cast-in-situ piles.

Oct 1, 2022

By Ian Vaz, Takefumi Takuma, Rafael Holcombe, Chris DellAringa

"This paper will discuss the successful installation of seawalls for the first phase of a project in Long Beach in California known as the Naples Island Permanent Seawall Repair – Phase 1. How an unconventional method of pile driving resulted in the reduction of the duration of the project while using less space and maintaining minimal noise impacts to accommodate neighbors will also be discussed. Included in the paper will be how non-vibratory equipment used on this project also significantly minimized the risk of disturbances as well as settlement on residential properties; which in turn greatly reduced the risk of damage to existing structures. The first phase of a 6-phase project along a section of the canals with tight clearances and proximity to residents included the installation of a 1,912 linear-foot steel sheet pile wall system in front of the existing deteriorating walls from January until March 2015.INTRODUCTIONThis project was located in the Naples Island neighborhood of Long Beach in southern Los Angeles County, California. After 80 years of the same seawall structures lining the canals of this beautiful neighborhood, the City of Long Beach Department of Public Works decided that it was time to better protect the area’s multi-million dollar homes by repairing its crumbling seawalls. The City realized that the walls will only become worse due in part to several concerns, including bending failure for the already deflecting walls. According to the City, certain sections of the walls had a significant risk of global failure if the area experienced a “moderate” near-source earthquake (City of Long Beach, CA, 2014b). Although the seawalls were in need of major repair, this would not be simple. Due to the tight clearances of the seawalls between the homes and canals, installation would be difficult with heavy, conventional construction equipment.Phase 1 of the project involved installing sheet piles on the water side in front of existing and aging vertical concrete seawalls between the Ravenna and Toledo Bridges along the Rivo Alto Canal. See Figure 1 for the General Plan for Phase 1. Financing for this project by the City’s Tidelands Capital Improvement’s Division allowed the construction to begin in a timely manner. However, the challenges for the City included regulatory restraints that further complicated the construction in terms of the duration of the project due in part to numerous regulations from several regulatory agencies."

Jan 1, 2016

By EFFC/DFI Concrete Task Group

Concrete technology continues to advance rapidly and modern mixes with five components – cement, additions, aggregates, (chemical) admixtures and water – often have characteristics which differ significantly from the older three component mixes – cement, aggregates and water. Recent trends have favoured higher strength classes and lower water/cement ratios, resulting in greater dependence on admixtures to compensate for reduced workability and to meet the (often competing) demands for workability in the fresh state and setting time. The application of testing methods which reflect the true rheological properties of the concrete has not developed at the same rate as the mixes themselves and it is still not uncommon for the slump or flow table test to be used as the only acceptance test for fresh concrete.A joint review of problems in bored piles (drilled shafts) and diaphragm walls cast using tremie methods by both the European Federation of Foundation Contractors (EFFC) and the Deep Foundations Institute in the United States (DFI) identified a common issue. The review determined that many of the problems were caused by (or in part due to) the use of inadequate concrete mixes with inadequate workability, or insufficient stability or robustness of the mixes. It further identified the primary causes as inadequate concrete specifications and inadequate testing procedures. The consequences of these problems are often significant and it has been recognised that spending more time and money on getting the concrete right is the most cost effective approach.A joint Concrete Task Group was set up by EFFC and DFI in 2014 to look at this issue and this guide is the output from that Task Group. A research and development project, funded by the Sponsors of this guide, is being carried out by the Technical University of Munich in conjunction with the Missouri University of Science and Technology. This project includes desk studies, laboratory testing, and onsite testing at worksites in Europe and the US. The research work will be completed during 2016.

Jan 1, 2016

By Brian M. Fraley

"Portions of the Catholic Total Abstinence Fountain in Fairmount Park in Philadelphia, Pa., were in “imminent danger,” according to a restoration services request for proposals (RFP) issued by the City of Philadelphia in August 2014. Open voids in the subsurface beneath the foundation were causing ongoing settlement of the fountain.The fountain was unveiled in 1876 as an ornamental drinking fountain for the Centennial International Exhibition, which celebrated the signing of the Declaration of Independence. Its creation was commissioned by the Catholic Total Abstinence Union of America, an Irish temperance organization that advocated for total abstinence from alcohol. Ironically, the fountain ran dry decades ago.The now-defunct fountain features a 100 ft (30.5 m) wide granite base with three steps in the shape of a Maltese cross. The centerpiece — enclosed by a 40 ft (12.2 m) diameter basin — is a 15 ft (4.6 m) tall statue of Moses perched atop an iglooshaped marble mound. Four subsidiary statues rise from granite pedestals at the tips of each arm of the cross, including Archbishop John Carroll, Charles Carroll of Carrollton, Father Theobald Mathew and Commodore John Barry.Natural and Man-Made DamageThe City of Philadelphia’s RFP called attention to three “high priority structural areas.” It was noted that Moses, Father Mathew and the steps surrounding the fountain had been documented as public hazards. The long-term effects of water infiltration had set in, eroding mortar joints and causing some stones to jut out. Furthermore, the stone base supporting the 16 ton (14.5 tonne) statue of Moses was in danger of collapsing. The statue of Father Mathew had been struck by lightning in 1910 and was repaired with an iron and metal pin anchor system, which had succumbed to corrosion. The city considered the statue of Father Mathew as the most threatened of the statues. Mike Miluski, P.E., vice president of Compaction Grouting Services (CGS), recalled “the fountain was in pretty bad shape” as he walked onto the site in August 2016 and immediately recognized the challenges ahead."

Jan 1, 2017

By Cassandra A. Wetzel

"Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.INTRODUCTIONRock-socketed mini-piles are a common and desirable deep foundation alternative to support loads more than 40 tons in New York City. Limited vertical clearance, accessibility, vibration control, and load capacity make this pile type attractive; it also does not require a static axial load test when socketed into rock. This added benefit makes this alternative all the more feasible.The installation of a drilled pipe extending to bedrock through a glacial till deposit presented challenges to the contractor and engineers to confirm the casing is seated sufficiently into the rock prior to drilling the rock socket. The loss of soil between the steel pipe and the till/bedrock interface can compromise the performance of the pile and soil loss can result in settlement of the ground surface.This paper presents the design and construction method changes made on one project during the installation of ten limited access rock socketed mini-piles."

Jan 1, 2017

By Peter A. Thompson, Richard E. Prust

"The Bangkok Mass Rapid Transit (MRT} Chaleom Ratchamongkhon Line project is the first underground subway to be completed in Thailand. It consists of 22 km (14 miles) of twin-bored tunnels and 18 cut and cover stations constructed within the deltaic deposits that underlie the city. This paper describes the ground conditions, site investigation, including the use of the self-boring pressuremeter and the associated design issues for the construction of deep foundations. The paper also describes a selection of the various deep foundation solutions that were adopted to address particular constraints of the project and the ground conditions, including slurry walls for the cut and cover stations and foundations used for the underpinning of existing structures.INTRODUCTIONThe MRT Chaloem Ratchamongkhon Line Mass Transit Underground Railway comprises approximately 22 km (14 miles) of tunnels and 18 stations. The route is shown in Figure 1.The project was divided into two design and build contracts. The northern section was awarded to the ION joint venture, composed of Italian-Thai Development PLC, Obayashi Corporation and Nishimatsu Construction Co Ltd. Arup were contracted by ION for the design of the northern section. The section comprises 11 km (7 miles) of twin-bored tunnels, nine cut and cover station tunnels constructed within perimeter slurry walls using top down construction methods, and two cut and cover tunnel structures.The majority of the route of the northern contract follows existing highway Rights of Way. This results in the tunnel alignment passing through the foundations of existing highway bridge structures for which a variety of deep foundation solutions were adopted to underpin these structures.An 8-story park and ride building in the Lat Phrao area was also constructed using deep foundations."

Jan 1, 2005

By Robert Bachus, Jamey Rosen, Fabio Santillan, Georgette Hlepas

"A seepage barrier of length 4,800 feet and maximum depth 144 feet is being installed at Bolivar Dam in Ohio. This project is owned by the United States Army Corps of Engineers and contracted to Treviicos South. Many data types are being collected, synthesized and analyzed on a nearly real-time basis to monitor and track dam construction using several technologies including an enterprise relational database and web-based Geographical Information Systems. These data are being collected by both the owner and contractor and managed by the data subcontractor, Geosyntec Consultants. Each of the owner and contractor brings their own list of goals and desires to the data management program, and the subcontractor’s duty is to address these goals with minimal compromise by either party. The owner requires comprehensive, transparent and timely access to data in both “executive summary” and detailed formats. The contractor requires immediate analysis of disparate data to determine (for example) if a given excavation meets the specified tolerance and continuity requirements. This paper will describe the tools and methods used to store, analyze and visualize these data and discuss how each party’s needs were met in a collaborative system.INTRODUCTIONThe 4,800 foot long seepage barrier under construction at Bolivar Dam requires the collection, organization, and sharing of several types of data. These data include drawings and borehole logs that existed prior to construction; data collected during construction (seepage barrier panel composition and verticality data, slurry quality control and quality assurance data, grouting records, etc.); and instrumentation data collected and reviewed throughout and beyond construction. Each of these data streams require input and review from the Owner (United States Army Corps of Engineers (USACE), responsible for quality assurance and the ultimate consumer of the data), the Contractor (Treviicos South, responsible for the construction of the seepage barrier, its quality control and analysis of the data per the Contract Specifications), and the Data Management Subcontractor (Geosyntec Consultants, responsible for organizing and presenting the data to meet the needs of the Owner and Contractor). While all parties work with the same common goal, i.e.: producing a high quality product in an efficient manner making dam safety paramount during construction, and require immediate and comprehensive access to these data, the needs and desires of the parties differ. The challenge presented to the Data Management Subcontractor is to synthesize these data into a series of tools and reports that meet each of these needs."

Jan 1, 2017

By Thomas G. Tavernaro, Jeffrey A. Schaefer

"The $106 million Olmsted Approach Walls Project, completed in the spring of 2004 by Massman Construction Co., Kansas City, MO, is one phase of a new $1.4 billion Corps of Engineers locks and dam facility located at Mile 964 on the Ohio River, approximately 17 miles (27.4 km) upstream of its mouth at the Mississippi River. When completed, the Olmsted Locks and Dam (Figure 1) facility will replace two aging locks and dams (Locks and Dams 52 & 53) built in the 1920’s, and produce an estimated $600 million annual economic benefit to the nation through reduced lockage time and operation and maintenance costs. PROJECT OVERVIEWThe Olmsted Approach Walls Project consisted of “in-the- wet” construction of four fixed nose pier structures, four floating concrete approach walls, one fixed wall and related underwater excavation, grading and stone placement. Over 12,000 tons (11,000 tonnes) of structural steel and pre-cast concrete elements, up to 335 tons (304 tonnes) in weight, were safely erected during the project.To support these massive structures, the Louisville District of the U.S. Army Corps of Engineers teamed with INCA Engineers, Inc., Bellevue, WA to design thirty seven 10’ (3m) diameter shafts (cast-in-place steel-shell piles) capable of maintaining elastic behavior below ground while resisting barge impact loads, extreme head-on collisions from runaway tows, and environmental forces from river current, wind, and seismic events.The shafts (typically 150’ (45.7m) in length) were founded 100’ (30m) into the riverbed through alluvium, a very consolidated fine sand and clay Cretaceous soil, and finally into a hydrothermally altered rock. Thirty seven shafts were installed under open river conditions at the site, a group of four shafts at each nose pier-pylon location (Figure 2), and 21 at the fixed land wall. Due to difficulty in achieving the required casing tip elevation the team developed a design modification that was successfully implemented for 27 of the shafts.Concurrent with the work at Olmsted, eleven pontoon segments for the four floating approach walls were constructed at a graving yard in Paducah, KY, developed by Massman Construction Company specifically for the project. While the pontoon geometry varied, the pontoons averaged 350’ (107m) in length, 40’ (12.2m) in width and weighed 4,500 tons (4,082 tonnes). The longest of the four walls, at 1,700’ (518m) was comprised of five interconnected pontoons."

Jan 1, 2006

By Reinaldo J. Villa, Joshua C. Adams

The I-395/SR-836/I-95 reconstruction project is an $818-million design-build construction effort that includes construction of viaduct, segmental and signature bridges in Miami leading into Miami Beach in Florida. Based on the load testing performed during the design phase, the design-build team determined that conventional driven pile and drilled shaft foundations were not feasible for support of segmental and signature bridges. Due to the weak limestone formation and successful use of auger cast-in-place (ACIP) piles in the Downtown Miami area on commercial developments, ACIP piles were selected as a foundation system to support bridges. This is the first time in history where the bridges will be supported by ACIP pile foundations in an interstate highway in the State of Florida. The design build-team worked closely with the Florida Department of Transportation to develop requirements for the load test program. The paper will provide an overview of the geotechnical data collected, results of dynamic/bi-directional load testing performed on test piles, data collected, installation of piles, and lessons learned. The load test program included a total of fifteen test piles with dynamic, bi-directional, and lateral load testing on 30 and 36-inch diameter ACIP piles and instrumented with thermal integrity profiling wires.

Sep 8, 2021

By Sunil S. Basarkar, Vinothkumar S

Ground Improvement Techniques serves to improve various engineering properties for supporting various foundations. These may be undertaken either by conventional or advanced methods. The Controlled Modulus Column (CMC), also known as Rigid Inclusion is a soil improvement technique to reduce the total and differential settlement by using semi-rigid soil reinforcement columns. The CMC technique can be executed by displacement or non-displacement methods. It does not aim to bypass the compressive layer or to install a pile that will directly support the entire load from the structure. Principle of the technique is to introduce a load transfer platform between the head of the column and structure and transform a uniform load into soil. Initially, the structural load transmitted into the soil generate the settlement greater than CMC piles. When the settlement between the soil and column became equal at neutral point, maximum structural load shall be balanced by the positive friction and tip resistance to stabilize the foundation without exceeding the allowable settlement limit. This paper describes the behaviour of soil reinforcement with CMC column and their installation process with reference to a project at the Dry Bulk Terminal Port, San Pedro- Abidjan (Western Africa). Methodology of CMC, requirements of Ground Improvement, arrangements and outcome of this method are presented in this paper.

Sep 1, 2022

By M. Krzaninski, Y. Zou, A. Frost

The foundation solution for a data centre building in Sydney, Australia comprised two alternatives, the first of which incorporated the use of CFA piles founded in rock at approx. 27m depth to support column working loadings of approx. 7.5MN, and the second utilising rapid impact compaction with a raft foundation of 1.0m thick concrete slab. Soil conditions comprised 1m of fill over 3 to 4m of sands varying from loose to dense consistency, underlain by very stiff clays overlying the rock. A creative solution incorporating Rapid Impact Compaction to improve the loose soils in conjunction with a piled raft solution was proposed. Piles proposed under the raft were Atlas Drilled Displacement piles which offered advantages of displacement pile performance and savings in time and material costs. The piled raft solution was developed in consultation with the consulting structural engineer, combining the skills of the piling contractor and consulting engineer to the benefit of the project. This paper describes the development and design aspects of the piled raft solution adopted for the project.

Nov 1, 2022

By N. Aarthi, G. R. Dodagoudar

The improvement of soft clay deposits using stone columns is a well-established ground improvement technique in the western world. This technique has been well documented and has proper design codes for precise execution in the field. The sand compaction pile (SCP) method is a contemporary technique to stone columns and has limited literature related to the strength characteristics of the loose to medium dense sand deposits treated with SCP. The available studies on the SCPs installed in cohesionless deposits focused on the improvement by indirectly assessing the SPT-N values pre- and post-installation of the SCPs. The widespread implementation of the SCP technique in recent years has increased the need for a more direct evaluation of the improvement. Earlier studies in this regard have revealed that the available design solutions are based on the type of installation equipment, their working efficiency, and accumulated field data. However, it is found that there are no generic design codes for the direct estimation of the ultimate bearing capacity of the SCP improved cohesionless deposits. To meet the design requirement for the SCP treated ground, a series of experimental and numerical investigations are performed in the present study to arrive at a direct framework in the form of design charts based on the pressure-settlement response of the treated ground. The developed design charts give the ultimate bearing capacity (UBC) of the treated sand deposit for the known initial relative density (RD) of the deposit, spacing and diameter of the SCPs, size of the footing, and for the specified target unit weight required for the intended application. It is concluded that the design charts will be of preliminary use to the design engineers to directly evaluate the UBC of the SCP improved loose to medium dense cohesionless deposits as part of the SCP method of ground improvement. It is expected to have more field-scale experiments and in-depth analysis before implementing these charts for actual field execution.

Nov 1, 2022

By Michael Arnold

"BAUER Foundation Corp. was one of three contractors awarded with the installation of a cut-off wall at the Herbert Hoover Dike Rehabilitation project. The cut-off wall was constructed up to 84 feet deep and 25 inches thick. It extended from the crest through the middle of the existing dike into the underlying peat, sand, and rock layers. BAUER used the cement deep soil mixing method of Cutter Soil Mixing (CSM) to install the wall. Soil mixing was facilitated by first removing the peat layer in the wall alignment using Kelly drilling and replacing it with suitable backfill, resulting in a secant pile wall arrangement of replacement columns. BAUER successfully finished four task orders with a total length of just over 10 miles. Up to six rigs of the types BAUER BG 28, BAUER BG 40 and RTG RG 25 were concurrently used to perform the replacement columns and the cut-off wall installation.The paper introduces the project, the geotechnical site conditions, and the requirements specified by USACE. It focuses on the specific adaptation of the CSM method to the site conditions and on the equipment used. Strength and permeability results obtained from an extensive testing program are presented. The impact of the curing conditions on lab and in-situ test results is studied, and test results are related to soil conditions.PROJECTThe Herbert Hoover Dike is a 143-mile-long dike encircling Lake Okeechobee in south central Florida. When it was constructed in the 1930s and 1960s, the purpose of Herbert Hoover Dike was flood protection from hurricanes. However, during the 1970s a higher lake level was maintained permanently to provide local agriculture with water. Later, damage became apparent during two nearly back-to-back high water events in the 1990s, when numerous sink holes, seeps, pipes, and boils were observed (Fig. 1). In 2000, the Congress approved USACE to propose rehabilitation measures. The installation of a cut-off wall into the existing dike was chosen during the initial design process as the preferred measure to improve the safety of the dike (Davis et al. 2009).The first section of the dike to be rehabilitated was Reach 1 located along the southeast side of the lake between the towns of Port Mayaca and Belle Glade. An indefinite delivery indefinite quantity (IDIQ) multiple award task order contract (MATOC) was issued for this 22.4-mile-long stretch by USACE in 2007. BAUER Foundation Corp. (BAUER) was one of the three contractors that succeeded in the qualification process. Each of the three successful contractors had their own novel construction techniques. In the years 2008 to 2012 BAUER executed four task orders totaling over 10.0 lineal miles of cut-off wall with 3.3 million square feet of design surface area."

Jan 1, 2015

By Dan A. Brown

The foundations at the Huey P. Long Bridge in New Orleans presented special challenges for construction due to the requirements for very deep drilled shafts in the Mississippi River beneath the existing bridge structure. Drilled shafts were constructed to depths of approximately 200ft in alluvial soils using a rotator system with full-length segmental casing, and base grouted to improve axial resistance. This paper describes the design and construction of the work platform to provide access to the restricted-access site beneath the existing bridge, the approach used to construct the drilled shafts, and the results of a load test program to verify the axial resistance.

Jan 1, 2010

By Filippo Mira-Cattò, Andrea M. R. Pettinaroli, Elena Rovetto

"The construction of Powisle station of Metro Warsaw Line 2, in Poland, required the execution of two shafts next to an urban road tunnel adjacent to the Vistula River. The shafts were linked by three conventionally mined tunnels to be excavated 10 m below the water table level, into an upper sandy and sandy silty layer and a lower stiff clayey stratum. After a failed dig attempt under the protection of jet grouting and forepoling, it was decided to deal with the tunnels excavation problem by using the ground freezing technique as a temporary, non-polluting geotechnical treatment, keeping in service the upper road tunnel. The planning of the activities and the executive phases had a significant importance for the success of the work. For work scheduling reasons the mixed system was adopted, i.e. using both the liquid nitrogen system and the brine freezing method. The freezing process management, with a real time evaluation of the soil temperature measured by thermometric strings and an accurate monitoring of the overlying road tunnel structure, allowed the tunnel excavation and lining stages to be performed under difficult conditions, without water leaking from the frozen ground shell, within the expected times and saving extra costs.INTRODUCTIONThe new Underground Line 2 in Warsaw connects the eastern and western part of the town. One of the most critical interferences was the under passing of the Vistula river and of the Wislostrada motorway tunnel, a very congested motorway along the western bank of the river, with the construction of the new station Powisle. The construction of the station required the excavation of two shafts, using the top-down system with the creation of intermediate slabs while deepening the excavation.The shafts were used for the extraction of four Tunnel Boring Machines (TBMs), two approaching from the Vistula river side (east-side) and two approaching from downtown (west-side); in order to connect the two shafts was foreseen the realization of three tunnels, two for the underground lines and the central one for the exchanging passenger platform. These tunnels were underpassing the “Wislostrada Road Tunnel” and interfered with this tunnel foundation, which consisted of diaphragm walls (DW), the “barrettes” (Figure 1).Due to the variable geological conditions at the site, the first excavation stage, with a temporary underground support constructed of horizontal jet grouting columns and forepoling, caused the North tunnel face failure, that required an immediate filling of the empty cavities with lean mix concrete under the Wislostrada tunnel slabs. Thereafter, the recovering attempt with the grout injections could not be completed because of the development of heaves induced on the tunnel structures (Bringiotti et al. 2016). In those conditions the tunnel excavation with traditional technologies appeared to be very problematic, with high risk for the structural safety of the Wislostrada tunnel. This would have meant longer duration for the works and higher costs for the General Contractor as well as for the city Council."

Jan 1, 2015