Search Documents

By M. Kamyab

The Deep Exploration Technology project, as part of the Australian Cooperative Research Centre, is developing technologies to drill deep boreholes for mineral exploration purposes. The aim of the initiative is to transfer drilling technologies from oil and gas into mining applications. Several modifications have to be pondered due to this technology exchange: smaller cuttings sizes because of using impregnated diamond bits; narrower annulus space; higher drilling fluid velocity and likelihood of turbulent flow regime in the annulus; and higher pressure loss. In particular the results of our lab experiments have shown that the increase in concentration of small size cuttings can significantly change the rheology of the mud when drilling in hard rocks. This, in return, could have a noticeable increase in the pressure loss encountered along the annulus space. As a continuation of the above study, numerical simulations were conducted to investigate the cuttings transport behaviour in small size annulus space. Fluid velocity, annulus size, cuttings concentration, cuttings density, and cuttings size were some of the parameters that were varied to see their effects on cuttings transportation and the pressure loss along the annulus space. The results indicate that, due to the differences between oil and gas and mining drilling, conventional oil well planning is not applicable for mineral exploration drilling and numerical simulation would help in this matter.

Aug 1, 2013

By Kai Zhang, Aijun Huang, Jeremy H. Rao, Xinhua Wu, Paul Rometsch

"As one of the most typical additive manufacturing (AM) technologies, selective laser melting (SLM) removes many of the shape restrictions that limit materials design, thereby allowing computationally optimised and high performance structures to be directly produced and tested. Due to the high reflectivity and lower absorptivity of Al alloy A357 powder during high temperature laser melting, one of the issues SLM might bring is the surface roughness and defects present on the parts. In this regard, this study investigates the surface roughness – fatigue property relationship for a heat-treated aluminium alloy A357 after SLM. Via the adjustment of SLM parameters, an ultrafine microstructure can be obtained due to the fast solidification rate. Therefore, comparable or even better mechanical properties can be achieved with respect to traditional A357 casting counterparts. Meanwhile, the surface roughness conditions of the SLMed Al alloy are also influenced by various processing parameters, raw powder properties, and sample building methods. For selective laser melted Al alloy A357 specimens, a dense part with a smoother surface would be expected to correspond with a good fatigue performance.INTRODUCTION Additive Manufacturing (AM), also known as 3D printing, is a process in which a complex part is fabricated layer by layer from a digital design package (Martin et al., 2017). AM has the potential to conserve raw materials, reduce the energy consumption, part cost, and fabrication time. Furthermore, as a typical additive manufacturing (AM) process, selective laser melting (SLM) was originally developed from selective laser sintering (SLS) based on higher quality lasers (Rao, Zhang, Fang, Chen, Wu, & Davies, 2017b). Different from conventional casting consuming valuable time and energy, SLM is now used as a cost effective method for the manufacturing of metals, such as Al-Si alloys, to produce almost full density parts using fine metallic powder and high power laser beam (Tang & Pistorius, 2017)."

Jan 1, 2018

By Vilkul Yuri

Operation of the iron ore deposits of Krivbass which has been going for 130 years, has led to serious problems related to reaching great depths in open pit and underground mining. Extraction of the huge volume of rock mass (about 9 billion m3) resulted in mass violations of the natural state of the subsurface. At present most mining operations are carried out either by combined open pit and underground mining or by open pits in areas underworked by underground mining. Now the process of movement of the strata underworked by underground mines is not completed ? work fronts of open pits approach the areas of possible funnel, terrace and fissure formation, movement continue to develop. With deepening mining operations the remaining reserves are worked off under layers of incumbent rocks of > 900 m. Significant underground voids arise from mining "blind" deposits at large depths. Heaving of voids over the mined area lasts for decades; it may result in not only unpredictable time of funnel emerging and area development of movement synclines, but also the threat of air blows in mines. Forced caving of incumbent rocks as a way of controllable backfilling is difficult to achieve for economic and technical reasons. This is much more expensive and dangerous than stoping. Furthermore, the mining practice does not know examples of enormous volume backfilling under a km thick rock layer. Currently, RMI "KNU" is conducting research and pre-design work directed at creating a specialized pilot Geoinformation System (GIS) of continuous remote monitoring of rock mass in areas of underground voids influence in Krivbass area. Implementation of this system will enable to determine promptly in time and space the areas of the beyond cut off stress condition, to inform about possible occurrence of events that may result in accidents and to improve safety of mining along with other systems of forecasting and controlling the stress condition in rock mass. RMI "KNU", with a large number of professionals from many Ukraine?s leading mining research centers, has developed a research and design work program that includes the following principal stages: 1. Analyzing geomechanical conditions of combined mining of magnetite quartzite and rich ore deposits; determining mechanisms of moving of rock strata underworked by underground mining and places of hazardous area monitoring. 2. Investigating anthropogenic factor influence on the safe state level of rock strata underworked by underground mining (laboratory studies). 3. Developing processing techniques for continuous remote monitoring of rock mass in areas of underground cavity influence. 4. Modeling the state of rock mass based on results of pilot GIS hardware measurements. 5. Developing an expert diagnostics system for rock mass state in areas underground void influence. 6. Experimental investigation and testing the GIS, its improving for efficient application. After testing the pilot GIS it is supposed to be implemented at all mining enterprises as an integral part of iron ore mining and processing technology in the Krivbass area.

Aug 1, 2013

By Paul Hammond

Abstract The Allard Lake ilmenite deposits, which are currently being developed on a large scale, occur as a series of dykes or lenticular, flat-lying bodies within the northeastern part of a large, oval shaped anorthosire mass of Precarnbrian age which lies with its long axis paralleling the gulf of St. Lawrence. The Lac Tio deposit, discovered by Kennco Explorations, Limited, in 1946, is the largest body of titanium ore of its type now known in the world. It contains upwards of 112,000,000 short tons of ilmenite ore averaging 32 per cent TiO2 and 36 per cent Fe. The ore is an aggregate of ilmenite with oriented microscopic blades of hematite. The deposits appear to be high temperature, late magmatic injections containing only a small amount of volatiles, and bear a genetic relationship to the anorthosite rocks in which they occur. * * * Introduction Recent developments on the ilmenite deposits in the Allard Lake district of Quebec indicate the probability of a major industry, and one which may make Canada the world's greatest producer of titanium pigments and, ultimately, of titanium metal. The presence of ilmenite in this district was first reported by the Quebec Department of Mines following a reconnaissance shore-line geological survey in the year 1941. The ensuing report by Retty describes the occurrence of a number of small ilmenite lenses about the shore of Allard lake and' along two smaller lakes in the vicinity. These showings were later staked by Toronto and Montreal interests who carried out a certain amount of development work, and were described in more detail by Longley for the Quebec Department of Mines. The claim groups were later optioned by Kennco Explorations, Limited, Canadian subsidiary of Kennecott Copper. None of the deposits in themselves constituted a sufficiently large body of ore to warrant the major construction expenditures necessary for their exploitation on a profitable basis. The surrounding anorthosite areas, however, were considered favourable for the possible occurrence of other ilmenite deposits

Jan 1, 1949

By D. J. MacKinnon

"The Canadian Copper Company, formed in 1885, began mining the nickel-copper ores of Sudbury in 1887 and producing nickel-copper matte from its smelter in 1888(1). Although it was quickly appreciated that the separation of nickel and copper (i.e. refining) was critical to the production of a marketable nickel product, refined nickel was not produced in Canada until about 1918. From the beginning of the industry, there was considerable political agitation to refine nickel in the Province of Ontario(2). The companies, however, claimed that the existing processes, viz. the sodium sulphide ""tops and bottoms"" process operated by the Orford Copper Company of New Jersey, U.S.A.(1,3,4) and the carbonyl process(5,6) developed by the Mond Company at Clydach, Wales, were too costly to operate in Canada. Nickel was first refined in Ontario about 1918 when the International Nickel Company opened a nickel refinery at Port Colborne, Ontario(6). Initially, however, the refinery at Port Colborne employed the Orford sodium sulphide process, and the first electrorefined nickel in Canada was produced in 1920 by the British America Nickel Corporation whose mine and smelter were located in Sudbury, Ontario, but whose electrorefinery was located at Deschenes, Quebec, near Ottawa, Ontario. The purpose of this article is to outline the early history of nickel electrorefining and to trace the significant developments which led to the first successful commercial electrolytic nickel refinery in Canada. The development of an electrolytic process for refining nickel is due largely to the efforts of four individuals, viz. Carl Hoepfner, Hans A. Frasch, D.H. Browne and ultimately N.V. Hybinette, and the contribution of each is discussed separately below."

Jan 1, 1999

By E. Peters

Roasting processes are divided into several elementary mechanisms, any of which could be significant or pre-dominant in a particular roast. The elementary processes considered in-elude beat transfer, gas-solid inter-actions with accompanying mass transfer between the bed and furnace atmosphere, vapor phase transport processes in solid-solid interactions, and solid phase diffusion processes. Examples are chosen of processes in which one of these mechanisms pre-dominates and some recently obtained data is presented to support the existence and significance of these mechanisms. Proposals are also made for future research in these areas, and for utilizing the information in the improvement of roaster capacities’ OASTING of ores as a preparative treatment for smelting or leaching has been practiced for so long that its origin has been lost in antiquity, but little has been under-stood of its basic nature until fair-ly recent times. The nominal chemistry of roasting processes is now understood; that is, the initial chemical com-pounds present in the ores or con-

Jan 1, 1961

By C. Blais, G. L’Espérance

Characterization of second phase particles is important with regard to their influence on mechanical properties of materials. Analytical electron microscopy offers the possibility to achieve complete characterization of inclusions. Complete characterization of inclusions means quantitative evaluation of their chemistry and the stereological parameters. A characterization technique based on integrated microscopy and involving scanning electron microscopy, image analysis and energy dispersive X-ray spectrometry is presented. A discussion of the use of transmission electron microscopy and electron energy loss spectroscopy is also presented for the characterization of very small particles and compounds (>100 nm).

Jan 1, 1998

By P. S. Arthur

The copper I SAS MELT? process is a submerged lance bath smelting technology. In the 20 years since the process was first demonstrated on a semicommercial scale at Mount Isa in north-west Queensland, Australia, copper ISASMELT? plants have been constructed to treat concentrates or secondary raw materials around the world. The process is operating in smelters in Australia, the USA, Belgium, India, Germany, China and Zambia. ISASMELT? plants have been installed to improve the environmental performance of operating smelters and reduce costs for smelting companies. A new copper furnace is being commissioned at Southern Peru Copper Corporation in early 2007, while more furnaces are under design for installation in Kazakhstan and Peru. Copper ISASMEL T? plants are supplied as complete technology packages including engineering design services for the furnace and key ancillaries, supply of core equipment, provision of intensive training programs in operating plant environments and commissioning assistance services. The proven technology transfer process ensures successful implementation of submerged lance bath smelting into large scale plants. This paper summarises developments at recently constructed copper ISASMELT? plants.

Jan 1, 2007

"The technical report form provides the headings to be used and content required when a completing a technical report to be filed in accordance with NI 43-101. The technical report is meant to be a summary of the scientific and technical information on the mineral property. The Instrument (NI 43-101) requires that technical reports be filed with Canadian provincial or territorial securities regulators to support certain disclosure of mineral exploration, development and production activities and results in order to permit the public and analysts to have access to information that will assist them in making investment decisions and recommendations. FORM 43-101F1 TECHNICAL REPORT INSTRUCTIONS (1) The objective of the technical report is to provide a summary of scientific and technical information concerning mineral exploration, development and production activities on a mineral property that is material to an issuer.This Form sets out specific requirements for the preparation and contents of a technical report. (2) Terms used in this Form that are defined or interpreted in National Instrument 43-101 Standards of Disclosure for Mineral Projects (the “Instrument”) will bear that definition or interpretation. In addition, a general definitioninstrument has been adopted as National Instrument 14-101 Definitions that contains definitions of certain terms used in more than one national instrument. Readers of this Form should review both these national instruments for defined terms.(3) The qualified person preparing the technical report must use all of the headings of the items in this Formandmay create sub-headings. If unique or infrequently used technical terms are required, clear and concise explanations must be included. (4) No disclosure need be given in respect of inapplicable items and, unless otherwise required by this Form,negative answers to itemsmay be omitted. Disclosure included under one heading is not required to berepeated under another heading. (5) The technical report is not required to include the information required in Items 6 through 11 of this Form tothe extent that the required information has been previously filed in a technical report for the property being reported on, the previous technical report is referred to in the technical report and there has not been any material change in the information. (6) The technical report for development properties and production properties may summarize the information required in the items of this Form, except for Item 25, provided that the summary includes the materialinformation necessary to understand the project at its current stage of development or production. (7) The technical report may only contain disclaimers that are in accordancewith section 6.4 of the Instrument and Item 5 of this Form."

Jan 1, 2003

By M. B. M. Monte, M. L. Torem, E. R. Pecanha, A. G. Merma

The recent literature has unveiled the potential use of microbial strains in mineral bioprocessing. This study presents the use of a Gram-positive bacterium (Bacillus subtilis) as bioreagent for hematite flotation. The bacterium presents the ability to modify the properties of mineral surface (electrophoretic mobility and hydrophobicity). It was studied the electrokinetic behavior of hematite particles, before and after the interaction with the bacterial cells. The results revealed a shift of the isoelectric point (IEP) of the hematite after interaction with bacterial cells, suggesting a chemical adsorption mechanism. Moreover, after bacterial conditioning, the zeta potential curve of hematite presented high values in the alkaline pH range. The hematite and the bacterial surfaces presented contact angle values around 27.4° and 41.0°, respectively. According to the results, the B. subtilis strain was capable of modifying the hematite surface, and after interaction the hematite surface presented a contact angle value around 46.0°. The flotation tests were carried out in a modified Hallimond tube. The experiments revealed a significant increase in hematite flotability using the Gram-positive strain as bioreagent. The tests pointed out a maximum recovery of hematite in the presence of 600 mg/L and pH 5. Therefore, the results from this study showed the potential use of the B. subtilis strain as a biocollector for hematite flotation, and its possible application in the mineral flotation industry.

Jan 1, 2016

By Kenta Suzuki, Toshiya Anami, Daisuke Shimosaka

"In an Al-Mn alloy heat exchanger fin stock, the effect of annealing conditions for as-cast and 0.1%Zr addition on recrystallization behavior is investigated using metallurgical analysis. Refinement of post-brazed recrystallized grains in fin stocks with Zr addition are suppressed for long-time annealing. In 0.1%Zr fin stocks, there was a decrease in the number of fine a-Al(Mn,Fe)Si dispersoids for pinning of sub grain and grain boundary. In addition, relatively homogeneous distribution of Al3Zr dispersoids was observed with increasing annealing time in as-cast. Homogeneous distribution of Al3Zr dispersoids can have a major effect on pinning of sub grain and grain boundary during brazing heat treatment. The homogenous distribution of fine dispersoids prior to brazing heat treatment is effective in causing the suppression of refinement of post-brazed recrystallized grain structure in aluminum alloy fin stocks.INTRODUCTIONAl-Mn based alloys are widely used as fin stocks in automotive heat exchangers because of their superior mechanical properties, braze ability, sagging and so on. In particular, coarsening of recrystallized grain structure is beneficial to avoid erosion, and achieve excellent sagging resistance (Lee, Yoon, Kim & Jung, 2002). For resisting grain coarsening, the alloys should contain a dense and homogeneous distribution of fine dispersoids to retarder crystallization (Humphyreys& Hatherly, 2004). It has been demonstrated that addition of Zr to Al-Mn alloys can shift recrystallization to higher temperatures because of the distribution of fine Al3Zr dispersoids in matrix(Pokoba, Cieslar& Lacaze,2012). According to Tohma, Asanoand Takeuchi (1987), coarsely recrystallized grain structure was obtained in 3003alloy with Zr addition after heat treatment. However, fine Al3Zr dispersoids are usually heterogeneously distributed because of segregation during casting and low diffusion rate of Zr in aluminum. Therefore, a homogeneous distribution of Al3Zr dispersoids can be achieved through long-time precipitation annealing(Jia, Hu, Forbord& Solberg, 2008)."

Jan 1, 2018

By K. Sakai, M. Miyaue, T. Aoki, T. Tani, S. Tanaka, N. Kudo

In the planning stage of a tunnel, due to limited available technology in the geological survey and the financial restriction, tunnel supports are often designed from unsatisfactory information, and the tunnel construction is started. Therefore, "observational construction" is carried out in the construction stage, in which the design is rationally verified and modified by observations/measurements. Moreover, the ground conditions ahead of a tunnel face must be predicted for efficient and safe tunnel construction. The authors have examined effective prediction methods to the ground conditions ahead of a tunnel face under construction of a mountain tunnel (Aoki et al., 2010) in view of the established method (Schubert et al., 1995). Though the prediction method of Schubert et al. requires the displacement in the direction of tunnel axis, it is difficult to obtain its accurate data by the electro-optical distance meter. Then, we have proposed a method that uses tilt sensors installed at the tunnel crown near the face to obtain the slight tilting information. To measure inclination of the tunnel crown, this inclinometer was originally developed as a daily management measurement, such that the geological condition and its possible change behind the face could be detected early, and a steady advance and construction safety could be ensured. This paper describes the method of forward prediction mechanism and advantages of this proposed method. It then presents the typical results of a field demonstration test at a tunnel under construction. Lastly, the predictable range from the stratum boundary at which ground stiffness changes are discussed based on the results of three-dimensional numerical analysis.

Jan 1, 2015

By R. Niechcial

As populations grow and industry expands, the limited fresh water resources available are increasingly under stress. This situation creates conflict between communities and industry; and the sustainability of both is threatened. The symbiotic relationship between community and industry highlights the need to develop innovative solutions to these water shortages. The sea may hold the key to providing the resource to permit the development of industry, the sustainability of communities, and the protection of the dwindling legacy water resources around the world. Desalination technologies have developed to where it is now economically viable to create industrial and potable water quality from seawater. Nowhere is this development more important than in the arid region of Northern Chile, where high copper prices have encouraged a boom in mine development.

Jan 1, 2007

By Siavash Zamiran, Abdolreza Osouli

"One of the most concerns of room and pillar mining system is subsidence of the ground surface due to coal mining particularly in room and pillar mines. Subsidence of ground surface is a result of floor, pillar, or roof failure of the mine. At the same, due to many difficulties associated with surface disposal facilities of coal refuse, some mining companies are trying to use underground space as a disposal storage place. In this study, stability and subsidence analyses of an underground coal mine located in the Illinois Basin are conducted. This room and pillar mine was abandoned and later on was used as a storage place to accommodate the coal fine refuse with slurry backfilling method. The geological stratigrophy and geomechanical properties of the mine floor and roof were collected. Floor and pillar stability analyses were conducted for areas with various extraction ratios. The stability of the mine was evaluated both prior and after slurry backfilling. The floor and pillar stability analyses results of the mine due to moisture exposure after slurry backfilling are discussed. The subsidence potential due to mine failure is also evaluated.INTRODUCTIONA typical lithology of coal seams in the Illinois Basin consists of weak underclay stratum. The immediate weak underclay causes frequent floor instability problems in Illinois underground coal mines. There are two different stages in assessing floor stability of the mines where slurry backfilling is planned. The first stage is during the mining operation when weak underclay layer squeezes under pillar stress and results in punching or bearing capacity failure. The second stage is after slurry backfilling. During this stage, the slurry material soaks non-durable floor layers and causes strength reduction in floor material. Pillar stability conditions should also be taken into account during both the operational period and after the slurry backfilling."

Jan 1, 2015

By W. J. D. Stone

"For several years, the existence of a deposit of barite (BaS04) near Brookfield, Nova Scotia, has been known. A very large deposit of strontium (SrS04) near Sydney, Cape Breton, is a more recent discovery. Cape Chemical Syndicate has been formed to work the deposits. A five-million-dollar integrated mineral processing and chemical plant is planned for Sydney to produce various compounds of barium and strontium. The mineral processing plant includes the Jones Wet Magnetic Separator and will produce high-purity barite and celestite. These products will be processed further in the fine grinding plant and the chemical plant. The general project is described, covering the deposits, processing and markets."

Jan 1, 1969

By D. Gagnon, B. Dubreuil, J. -M. Lalancette, D. Lemieux

"The pilot scale extraction of gold with a brine of sodium chloride and bromide at 30 ºC, in an atmosphere of halogens at atmospheric pressure, leads to gold chloride with 95% gold recovery. The use of dilute hypohalites (1 – 3%) instead of free halogens, which is strong enough to oxidize hypobromite into bromine, simplifies the recycling of halogens by electrolysis. With the recycling of water and brine, the regeneration of hypohalites and with a barren solid that is inert and stable. The Nichromet Extraction technology is a green process where the protection of the environment does not preclude profitability.INTRODUCTIONThe use of chlorides for the extraction of gold predates the discovery of chlorine by Scheele in 1774. In the Plattner chlorination process (Christy, 1888) sodium chloride and copper salt were used to promote gold recovery by amalgamation with variable results. The introduction of the cyanide technology in 1889 has led to a general use of this method for gold recovery. In the last decades, a return to chlorine in extractive processes has been noted (Ferron, Fleming, O’Kane and Dreisinger, 2002), mostly because of environmental pressure for non-cyanide technologies.This paper describes a closed circuit proprietary approach (Lalancette, 2009) developed and piloted by Nichromet Extraction Inc. for the extraction of precious metals with recycled mixed halogens; chlorine and bromine from hypohalites. DESCRIPTION OF THE PROCESSThe attack of gold by halogens can vary significantly. The rate of reaction is substantially higher with bromine (Br2) than with chlorine (Cl2), by a factor of more than five, although the oxidation potential of Cl2 is higher than Br2, as shown in Equation 1a and Equation 1b (Latimer, 1952)."

Jan 1, 2012

By Iain Sommerville, Hugh Mountford, Dawid D. Smith, Claude Dube, Brett Hixson

JW Aluminum use lean and Six Sigma techniques to continuously improve their target of reliable, repeatable and reproducible (3R) manufacturing. Six Sigma’s second stage gate, known as "Measure" involves identification and qualifying appropriate measuring systems. Metal quality (inclusions) are known in the industry to be an important element in 3R casting. The measurement of inclusions at JW Aluminum historically depended on outside vendors. In order to establish real time inclusion measurement ability within JW Aluminum, inclusion measurement systems in the marketplace were investigated. The qualification of a MetalVision MV20/20 ultrasonic inclusion analyzer are discussed as well as the subsequent application of the system in melting and casting improvement projects.

Jan 1, 2015

By W. Schubert, N. Radoncic

"The term “squeezing” is frequently used, although it is ill defined. Definitions like “large and long lasting displacements” raise the questions about the threshold values for the magnitude and duration of displacements. Large displacements during tunnelling frequently are observed in fault zones with high overburden. Whether this causes problems very much depends on the design approach used. On the one hand, the magnitude of expected displacements has to be predicted prior to excavation to provide for enough allowance for the displacements without violating the clearance profile. On the other hand, the support characteristics must be compatible with the expected imposed strains. As the magnitude of the displacements and thus the strains in the support depend on the support capacity and its characteristic (yielding potential), only well engineered systems will be successful.Experience in Alpine tunnels over the last decades has shown that closed shotcrete linings can sustain a strain of approximately 0.8% to 1% without failure. Any strain above this value inevitably leads to failure of the lining, and thus a loss of resistance, causing additional displacements. Based on a large number of simulations, a criterion for a critical overburden depth up to which closed linings can be used has been developed. Traditionally open gaps in the shotcrete linings have been used to allow for larger strains. To enhance the efficiency of the linings, yielding elements have been developed, which are integrated in the shotcrete lining, allowing large strains and controlled development of support resistance (Figure 2). When designing such yielding support systems, the development of the displacements, as well as the rheological behaviour of the supports must be considered. As the development of displacements to a large extent depends on the face advance, also the advance rate has to be considered, to be able to compare the time-dependent strength of the lining to the stresses developing as a result of the imposed strains. Another issue is the compatibility of the rock bolts with the large strains. With standard grouted bolts, there is a potential that the “fresh” grout is sheared due to the initially large strain rates. Special rib designs of the bolts allow for a higher strain tolerance.For successful tunnelling through fault zones quality monitoring and up-to-date data evaluation is of crucial importance. With advanced evaluation tools, changes in the ground conditions ahead of the face can be reliably predicted. With the help of empirical relations, the development of the displacements for different advance rates and supports can be predicted, allowing for the determination of the required overexcavation.The paper presents a review of the development of ductile elements, methods of analysis, and monitoring data interpretation."

Jan 1, 2015

By K. S. Raja, B. McNall, B. Pesic

"High-level radioactive wastes are stored in large underground storage tanks made of low-carbon steel. The wastes consist of concentrated solutions of sodium nitrate (NaNO3) and sodium hydroxide (NaOH), and the radionuclides 137Cs, 99Tc, and 90Sr. The corroding steel microenvironment may produce localized reducing or oxidizing conditions that affect the solubilities of the species such as Tc(VII) and Tc(IV), which in turn modifies the kinetics of corrosion of the storage tank. To understand the influence of technetate ions on the corrosion of steel, electrochemical polarization studies of A 537 steel samples were carried out in 1 M NaNO3 + 0 .05 M S r(NO3)2 + 0.1 M NaOH with and without addition of HReO4 at different temperatures (24 – 85 °C). The concentration of HReO4 was varied from 0.014 – 0.04 M.INTRODUCTIONAqueous processing of spent nuclear materials generates a large amount of high-level radioactive wastes. The wastes are primarily salt solutions of sodium hydroxide and sodium nitrate which also contain fission products such as 137Cs, 99Tc, and 90Sr. Among the high level radioactive fission products, Tc-99 is of great importance because of its high concentration, long half-life (2.1 x 105 years), high solubility in geologic waters as technetate, and rapid diffusivity through the geologic systems. The solubility of technetate ions varies depending on the oxidizing conditions prevailing in the storage containers. High level radioactive wastes are stored in single shell or double shell tanks made of low carbon steels such as ASTM type A15, A516-70 and A537. Most of the available literature on corrosion of steel in simulated radio active waste environments pertains to nitrate induced stress corrosion cracking (Subramanian & Mickalonis, 2005). The corroding steel microenvironment may produce localized reducing or oxidizing conditions that affect the solubilities of the species such as Tc(VII) and Tc(IV). Corrosion of steel and formation of Fe(II) and Fe(III) will affect adsorption and reduction of Tc species. The radioactive species can irreversibly be sorbed on the steel surface by oxidation of Fe(II) to more stable Fe(III) and fixed as less soluble Tc(IV)/Fe(III). The solubility of Tc species is also affected by other factors such as dissolved oxygen, local pH, temperature etc. How the corrosion behavior of steel will be affected in the presence of Tc species is not clearly understood.Cartledge (Cartledge, 1960) demonstrated that passivation of iron can be achieved in the presence of oxygen along with suitable inhibitor ions/molecules of the general formula XO4 n-, such as pertechnetate (TcO4 -). The pertechnetate ion is univalent. Since it is derived from a strong acid, no buffering action can be expected from this ion. The redox potential of the reaction (1) is 0.738 VSHE (Pourbaix, 1974)."

Jan 1, 2012

By C. Holmes, T. Holmes

Engineered-in material handling problems are responsible for significant unrealized value in mineral processing plants. At the root, is a lack of awareness and understanding of bulk material handling science and how important it is, especially in early design stages. Mineral processes add value to mined raw feedstock through physical and chemical transformations in unit operations, but only if the material can flow through them. Essentially, each unit operation receives a unique feedstock and produces a unique product to be collected, transported, and fed into the next unit operation. Such material-handling systems can only be expected to achieve design throughput if the system equipment is designed to the materials’ characteristics, over their full range of conditions. This requires quantification of flow properties to support the necessary customized equipment designs. Too often, assumptions or “library values” of a material’s properties are used as the basis for flow modelling and conceptual, and sometimes even detailed, design. This is especially true for hazardous materials like uranium ore, for which the additional precautions, costs, and time necessary for safe handling are often used to rationalize postponing or even bypassing testing. The surprises that often transpire in the wake of insufficient material handling consideration can have acute and costly effects. Fortunately, there is a better way.

Jan 1, 2020