Search Documents

By Patrick Rennkamp, Wolf-Dieter Trodel, Andy Fearn

"The Jansen shafts are completed using purely mechanical excavation. This paper summarises the geology, a description of the shafts, the method used for excavation and the results achieved along with the challenges encountered and the solutions developed during the project. This experience is now being applied in the next generation machines and shaft sinking processes. This pioneering approach is changing shaft sinking in soft and medium to hard rock. INTRODUCTION The Jansen Mining project located approximately 150 km east of the city Saskatoon is the location of the BHP owned potash mine with an expected mining output of eight million tonnes annually upon completion. Mining contractors DMC Mining Services have used two Herrenknecht Shaft Boring Roadheaders (SBRs) to excavate the two blind shafts with an approximate excavation diameter of ten metres (inner diameter approximately 8.3 m) to depths of -975 and -1005 metres, respectively. The SBRs excavate the rock by a partial-face cutting method, using a transverse cutting drum mounted on a telescopic boom. The excavated rock is then conveyed away from the bench by an innovative pneumatic system and transferred into muck buckets to be hoisted to the surface. No drilling and blasting was done to keep to the BHP philosophy of using only mechanical excavation for this reference project. BHP VISION – MECHANICAL EXCAVATION BHP focused on mechanical excavation at Jansen due to the following perceived benefits: 1.No workers in the excavation chamber (shaft bottom), minimizing the exposure to traditional shaftsinking hazards associated with working in the shaft bottom. 2. Minimal damage to the rock fabric reducing the need for ground support and avoiding potential impact damage to freeze tubes located around the shaft. 3. Accurate excavation diameters with no overbreak, reducing volumes of rock to be removed and replaced with concrete lining."

Jan 1, 2019

By A. McGrath, M. Trovant, M. Haque

Minimizing energy consumption is a priority for many industrial facilities. Metallurgical and gasification processes produce dirty syngas (CO and H2), which offers the potential for energy recovery. However, syngas handling can pose an explosion risk and even minor leaks can result in poor workplace hygiene. Furthermore, many jurisdictions around the world now discourage wet syngas handling due to limited water availability and secondary pollution. Hatch has developed a 100% positive pressure gas handling system that targets these safety hazards without using fresh water. The implementation of a system for calcium carbide smelters at Qinghai Salt Lake Industry Co. (QSLIC) in China is profiled as a case study.

Jan 1, 2015

By A. H. Lang

"IntroductionMUCH PROSPECTING, exploration, and development work was done for uranium in Canada in 1952, chiefly in northern Saskatchewan and in the Great Bear Lake region of the northwest Territories. The outstanding feature of the year was the great amount of work done in preparing for production at the Ace mine of Eldorado Mining and Refining, Limited, in the Goldfields region . of Saskatchewan. Many private companies and prospectors were also active in this region. Most of the other parts of Canada where uranium has been found received less attention than during the last few years, partly because so much interest was taken in the Goldfields region.In presenting this short summary of the year's activities now, the writer is handicapped because the season is not yet over; some discoveries have probably not yet been announced, and there has not yet been time to digest the numerous reports that have been sent in by companies and prospectors. In any case it would be impossible to give details for most of the discoveries and properties, because that would require a long report, and because that information is classed as confidential until released by the discoverers and companies concerned. It is only possible, therefore, to give a few generalizations, a brief out-line of the activities in northern Saskatchewan, even briefer ,accounts of the work in other parts of the country, and a few details that property owners have informed the writer he may publish or that have already been published by the owners."

Jan 1, 1953

By R. F. Coulter

THE Flin Flon concentrating and metallurgical plants (Figure 1) of the Hudson Bay Mining and Smelting Co., Limited, lie adjacent to the town of Flin Flon, on the Manitoba-Saskatchewan border, 400 miles northwest of Winnipeg. Since the start of milling operations in 1930, over 50 million tons of ore from the Flin Flon mine have been treated in the concentrator. During the past few years, newly discovered orebodies have been brought into production and their ores processed at the company's main metallurgical plants. All these properties are within a 75-mile radius of Flin Flon and have aided substantially in augmenting plant metal production as well as retarding depletion of ore reserves in the Flin Flon mine. •Current satellite producers are the Schist Lake, Coronation, and Chisel Lake mines. The Schist Lake mine, located 3 ½ miles southeast of the main plant, is a copper-zinc producer. It was brought into production in 1954. The

Jan 1, 1962

"The outlook for Eastern Canada is decreased coal production and for Western Canada increased production. The market for Western coal is expected to reach 40 million tons per year in metallurgical and thermal-power markets.Technical developments in Eastern Canada include successful methane drainage experiments, modifications to the shearer-loader to improve cutting rates, mechanized mining of a tail-gate stable and mechanical stowage of level brushing. In Western Canada, the most modern equipment is used in mining, beneficiating and shipping coal. Underground hydraulic experiments were started in 1969. The importance of reclamation was recognized and plans have been made to re-vegetate disturbed areas and mine dumps.The Mining Research Centre closed the field office in Nova Scotia and is preparing to open a new field office in Calgary, Alberta."

Jan 1, 1970

By B. W. Steele

"Dofasco began operations in 1912 as a steel foundry located in Hamilton, Ontario. Today, Dofasco is a fully integrated mill that manufactures hot rolled, cold rolled, galvanized and tinplate steels. Customers include the automotive, construction, tubular, manufacturing, appliance, packaging and steel ser-vice centre industries. Raw steel production and purchased semi-finished steel processed in1994 was 3.5 million net tonnes. Dofasco employs 7300 people at its Hamilton facility.Environmental management at Dofasco is guided by its environment policy and associated commitments. This paper discusses Dofasco’s responsibility for its products as it relates to these commitments. Dofasco is com-mitted to:n the principles of sustainable development that require that activities be conducted in a manner that provides for the present without compromising the ability of future generations to meet their needs. These principles will be integrated into product design, manufacturing and business planning;n managing renewable and non-renewable resources through the responsible application of reduce, reuse, and recycle principles;n minimizing any potential impact of its operations and products on the environment, employees, customers and the community;n continuous improvement of the effectiveness and integrity of our environmental management systems;n developing understanding among all employees about their responsibilities, and assigning the necessary authority; andn meeting the standards set by relevant legislation and international agreements through participation with governments and the diligent application of economically feasible and scientifically sound methods and technologies."

Jan 1, 1996

By H. L. Noblitt, Pauline Moyd, Louis Moyd

The deposit, which forms a ridge -adjacent to the York river, in Mont-eagle township, is held by Monteagle Minerals Limited, of Toronto. The ore is in a Precambrian gneiss which is composed of nepheline, scapolite, andesine and microcline feldspars, muscovite and biotite micas, and -corundum. The major orebody is tabular and is exposed for 1,200 feet along the crest of the ridge. It aver-ages about 90 feet in thickness, dips at about 70°, and was intersected by drilling at a vertical depth of 600 feet. The deposit was prospected for corundum in the early 1900's. Recent exploration was undertaken to deter-mine its potential as a source of high-alumina ceramic material, with by-product corundum and white mica. The program included prospecting, mapping, trenching, diamond drilling, bulk sampling, beneficiation research, a large-scale beneficiation test, product evaluation, market investigations, and plant design. Reserves, to a depth of about 300 feet, are estimated at about 3 million tons.

Jan 1, 1962

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to maximise health and safety performance in the mining industry through implementing continual improvement in management of major unwanted events. A comprehensive knowledge base has been captured for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This will be extended to outburst, coal burst and bumps, interface displays and controls, tailings dams and inrush in 2013. RISKGATE presents substantive and leading edge controls to assist industry stakeholders in the design, management and reporting of organisational and regulatory compliance requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry. All major Australian mining companies are contributing topic experts to this broad industry initiative. In the first 24 months, nine coal mining companies nominated over 80 different experts who contributed over 400 days of individual time to the knowledge capture workshops. RISKGATE is the largest single Australian Coal Association Research Program (ACARP) occupational health and safety (OHS) initiative to date.

Aug 1, 2013

By John L. Hatton

The author will introduce and describe the nature of Fiberglas-Reinforced Plastics. Successful applications of corrosion-resistant structures will be shown and described, including pipe, ducts, tanks and other equipment. These structures are generally designed to handle corrosive liquids and gases and have proved both satisfactory and economical in service in various industries in Canada. The specification of structures will be discussed in relation to materials, construction and workmanship, physical properties and methods of testing.

Jan 1, 1970

By A. Henk, C. M. Aruffo, K. Fischer

"Geomechanical reservoir modeling offers a valuable tool to predict tectonic stresses, in particular the local perturbations in orientation and/or magnitude which occur at lithological boundaries and faults. The paper presents a workflow for building and calibrating such geomechanical models. The numerical simulations are based on the Finite Element method and can range from field-scale models to smaller, highly detailed submodels of specific fault blocks. The approach considers the reservoir-specific characteristics with respect to subsurface geometry (lithostratigraphic boundaries, faults), mechanical properties and ambient stress field. During the subsequent calibration stage calculated stresses are compared to stress data actually observed in borehole data. Poorly constrained input parameters are iteratively modified within reasonable limits until a satisfactory fit between calculated and measured stresses is achieved. This validated model can then be used for stress predictions between wells and in undrilled parts of the reservoir, respectively. The workflow is applied to two case studies - a large gas field in Northern Germany and a CO2 sequestration project in Australia – to test and illustrate its practical value. INTRODUCTIONDetailed knowledge of the tectonic stress field is crucial for the optimal exploration and use not only of conventional and unconventional hydrocarbon reservoirs, but also for deep geothermal reservoirs, carbon capture and storage (CCS) projects as well as underground mining and nuclear waste repositories. Any reliable stress prediction is hindered by the observation that the magnitude and orientation of the stress field can vary significantly – not only in time, but also in space. Such spatial stress variations comprise all scales, i.e., from the scale of lithospheric plates down to the grain-scale. On the reservoir- and fault blockscale, the local stress field can be influenced by faults and different mechanical properties of lithologies (Sassi & Faure, 1997). The resulting variations in stress magnitude and/or stress orientation are commonly referred to as stress perturbations and give rise to a unique, reservoir-specific stress pattern (Yale, 2003). Thereby, local stress fields can deviate by up to 90° in orientation and several tenth of Megapascal (MPa) in magnitude from regional trends."

Jan 1, 2015

Originally developed as a step change in ultrafine grinding efficiency, the IsaMill? has made inroads into conventional ball mill and tower mill mainstream grinding duties during the last 5 years - beginning with the Anglo Platinum mainstream grinding projects in South Africa. At the 2006 SAG Conference, plant testwork on the incorporation of IsaMill? technology into the McArthur River (Northern Territory, Australia) Pb/Zn primary grinding circuit was reported. The IsaMill? has now become an integral component of that circuit, treating up to 1mm top size feed and directly producing P80 45 µm rougher flotation feed. Two 1.1 MW IsaMills? are now used in this duty contributing to a 27% increase in overall plant throughput and a reduction in rougher feed size distribution. In this paper, we report on the current state of development and performance of the IsaMill? in the primary grinding duty at McArthur River and also consider future directions.

Jan 1, 2012

By M. H. Pettibone

Sohio Petroleum Company's new L-Bar uranium mill near Grants, New Mexico. refines 2722 kilograms of yellowcake daily from 1360 metric tons of ore produced at Sohio 's J.J. No. 1 mine and other nearby mines. This paper follows the ore from the mine through the various processing steps - semi-autogenous grinding, acid leaching , countercurrent decantation, solvent extraction , ammonium diuranate precipitation, washing and drying, and tailings disposal.

Jan 1, 1978

By A. R. Farkoosh, K. Korgiopoulos, McGill University, O. Rodop, L. A. Villegas Armenta

"New generation of Al-Mg-Si alloys with thermally stable dispersoids that prevent recrystallization and grain growth during hot deformation are currently used in automotive components requiring good formability. Alloy chemistry controls the phase formation especially age-hardening precipitates, dispersoids, and primary intermetallic which have pronounced effect on grain structure, strength and formability. In this work, thermodynamic calculations have been used to predict the effects of varying levels of Si (0.5-1.5wt%), Mg (0.5-1.5wt%) and Mn (0.1-2.5wt%) on phase selection. Thermodynamic calculations have been performed in equilibrium and non-equilibrium conditions via the FactSage™ software using the FTlite database. Selected compositions have been cast, heat treated, extruded and characterized through scanning electron microscopy with energy dispersive spectroscopy and electron channeling contrast imaging techniques. The calculations showed that at the hot deformation temperature of ~540 oC, exceeding certain Mg and Si levels would lead to retained *-Mg2Si intermetallics and Si particles at the grain boundaries in addition to a-Al-(Mn,Fe)-Si. It was found that retained *-Mg2Si phase which adversely affects formability can be avoided for Si+2Mg levels lower than 2.3wt%. FactSage calculations also showed that increasing Mn from 0.5wt% to 1wt% leads to an increase in the amount of dispersoids (from 1wt% to 2wt%) that can potentially slow down recrystallization and grain growth during hot deformation and improve formability. Calculations at room temperature also show that for an alloy with 0.7wt% Mg, excess Si beyond 0.7 wt% promotes the precipitation of Si clusters in the Al matrix that accelerate natural age-hardening. Results were confirmed by experimental investigation.INTRODUCTIONAluminum alloy 6082 (Al-Mg-Si) is used in the automotive industry because of its high strength, and good weldability (I. J. Polmear, 2006). The alloy is age-hardenable through the precipitation of ß-Mg2Si and its precursors, and the recrystallization is usually inhibited by Mn- and Cr-containing dispersoids formed through high temperature heat treatments (I. Polmear & Couper, 1988). However, it is known that minor changes in alloy chemistry (Mg/Si ratio) can have significant influences on the ductility and formability of these alloys by altering phase selection and the resultant microstructure (Gupta, Lloyd, & Court, 2001; McQueen & Celliers, 1997; Zajac, Hutchinson, Johansson, & Gullman, 1994). For automotive applications where wrought alloys (usually extrusions) are cold-formed to produce suspension components, the chemistry of the alloys and the extruded structure are of crucial importance as they determine the formability at room temperature (Asensio-Lozano, Suárez-Peña, & Vander Voort, 2014). In this study, thermodynamic calculations along with experimental investigations were carried out on the Al-Mg-Si system to understand their phase formation and precipitation hardening as a function of alloy composition."

Jan 1, 2016

By C. S. R. Rondestvedt

In February 2010, Teck?s newest Concentrator at Mina Carmen de Andacollo (CDA), Andacollo, Chile was commissioned. The Concentrator is a single line configuration, comprising of one 36 ft diameter x 20 ft long SAG mill driven by an 18,000 hp gearless drive. The SAG mill feeds two ball mills each 25 ft in diameter x 40.5 ft long, each driven by a total of 19,000 hp through dual pinion drives. A series of four phases will be reviewed from operational readiness, mechanical completion, commissioning, and ramp-up. Also, now after 6 months of operation, this paper will review the significant steps taken during ramp-up enabling the announcement of commercial production, in October 2010.

Jan 1, 2012

By D. S. Flett, A. V. Tolstov, M. A. Mulagaleeva, N. V. Gudkova, A. M. Zhizhaev, V. I. Kuzmin, Institute of Chemistry and Chemical Technology SB RAS, O. A. Logutenko, V. N. Kuzmina

The complex niobium-rare earth pyrochlore-monazite-crandallite ores of the Tomtor deposit, located in the Siberian Arctic, should be considered as a new type of rare metal materials. The major valuable components of the ore are niobium, rare earth elements, yttrium, and scandium; associated components are titanium, vanadium, aluminum, and phosphorus. Because of the irregular distribution of the rare earth metals and niobium according to grain-size, the extremely finely dispersed nature of the minerals and their close interpenetration to each other, ore processing by gravitation and flotation is not successful. The processes studied for the treatment of the Tomtor ores use direct alkaline-acid leaching to open the ore. A problem in the first stage of alkaline leaching is the high aluminum content, which decreases the activity of sodium hydroxide and alkaline-earth metals, which are bound to phosphorus. Ore processing using alkaline-nitrate and alkaline-chloride leaching was proposed and investigated. The first variant was used to obtain rare earth and scandium materials and a niobium-titanium concentrate, which can be a stock material for processors who use chlorination for the processing of ores and concentrates. The second variant is a complex advanced ore processing scheme with electrochemical regeneration of the waste chloride solutions obtaining sodium hydroxide, hydrochloric acid, and chloridizing agents. Moreover trisodium phosphate is used for purification of the waste mother liquors from metal cations. The complex salt, NaAlCl4, is proposed as the chloridizing agent for the decomposition of the niobium-titanium concentrate.

Jan 1, 2016

By K. Soldenhoff, M. Fainerman-Melnikova

The use of strong base resins for uranium recovery is severely affected by the presence of chloride ions in solution. In areas where high-quality process water is not readily available, the use of saline water would extend the potential application for ion exchange in uranium processing. This study presents measurements of uranium uptake, using a wide range of commercially available weak base anionic exchangers, from solutions with chloride concentrations ranging from 2.5 to 22 g/L Cl. Out of 14 weak base anionic resins tested, 3 were identified that were not severely impacted by the presence of chloride and significantly outperformed a gel strong base resin typically used for uranium recovery in high-chloride environments. The uranium loading was sufficiently high for the consideration of development of the application of uranium recovery from uranium ores leached with seawater.

Jan 1, 2012

By The Staff

"THE property of Red Mountain Mines Limited is located 11/2 miles north and west of the town of Rossland, in southern British Columbia. The mine is situated on the flank of Red mountain, famous in pioneer days as the site of a number of profitable gold-copper producers. Mining and milling commenced in May, 1966, and by the first of July the concentrator was treating close to its average design capacity of 400 tons per day. The following description of the property and its operations is divided into three parts, dealing respectively with geology, mining and milling.GeologyAll the known ore reserves of Red Mountain Mines occur on the Coxey claim, on the west slope of Red mountain. Although there are indications of molybdenite mineralization elsewhere on the Company's property, these have not been developed.The Coxey and adjoining areas are underlain by the Mount Roberts formation of the Rossland volca-nics. This formation consists of an interbedded series of volcanic and sedimentary rocks, mostly brecciated and silicified near the ore zone, and all intruded by igneous rocks which occur in various forms, and vary in composition from basic to acid. The country rock in the vicinity of the mineralization seems to be mostly a volcanic, approximately andesitic in composition, and possibly a surface flow. There is much banding, some of which is undoubtedly due to tuff and agglomerate layers, and some to narrow, siliceous, sedimentary horizons such as the surface exposure of the main ""A"" orebody, much of which was a thin capping of greyish banded rock that looked like quartzite. The drill holes also intersected occasional layers of black, argillaceous quartzite, sometimes altered to a greenish colour. The whole assemblage has been silicified with varied intensity, sometimes to such an extent as to have obscured or obliterated the original characteristics. The mineralized zone has also been strongly brecciated, the fragments varying in size from less than an inch up to large masses, best described as a mega-breccia. Anomalous results obtained in drilling, such as sedimentary sections that do not appear in adjoining holes, may sometimes be due to the presence of these large blocks, no longer in their original position. The whole volcanic unit is thus very complex and confusing. For practical purposes, the ore may be said to occur in a greenstone formation with minor sedimentary interbeds and considerable later igneous material."

Jan 1, 1967

By S. Nikolic, G. M. Stieper, D. P. Mallah, B. J. Hogg, P. B. Voigt

Copper feed materials processing is becoming more challenging, due to an incremental increase in the mineralogical and compositional complexity of these feeds. These complex and polymetallic feeds are now becoming more common and many sites have been forced to re-evaluate their operating strategies to process these materials at cost competitive rates, whilst meeting ever more stringent environmental regulations. Most operations must first evaluate the merits of pyrometallurgical and hydrometallurgical treatment routes. Although there are multiple copper smelting technologies available, only top-submerged lance (TSL) technology, supplied by Glencore Technology as ISASMELT™, has been applied in the real world to consistently and successfully smelt complex materials in integrated metallurgical facilities such as Glencore’s Kazzinc Ltd. operation in Kazakhstan, Umicore Precious Metals Refining in Belgium and Aurubis AG in Germany. Glencore Technology also offers hydrometallurgical processing, through the Albion Process™ technology, opening up viable flowsheet options previously not possible for these complex feeds. This paper describes a number of real world process flowsheets at global operations and Glencore’s own operations at Mount Isa and Kazzinc Ltd., which process complex feeds. These flowsheets integrate the ISASMELT™, Albion Process™, ISACONVERT™, ISAKIDD™ Tank house, and bottom blown oxygen cupel (BBOC™) technologies to provide an effective process solution for the treatment of complex polymetallic feeds to produce metallic copper and associated by-products. INTRODUCTION Traditional smelters and those built in recent times within the bulk smelting hubs of the world have been designed to treat standard/clean concentrates. In recent years the processing of complex polymetallic sulfide concentrates and the recycling of secondary copper and derivatives of waste electrical and electronic equipment, such as e-scrap, have become a focus for numerous companies (Alvear & Nikolic, 2013). Processing of these complex feeds, characterized by relatively high levels of minor elements (over 5% of elements such as arsenic, antimony, bismuth, lead and zinc) is more challenging. Facilities not designed for these types of materials may require significant modifications or a change in smelting technology to treat them. Often operations find themselves re-evaluating the merits of pyrometallurgical and hydrometallurgical treatment routes for their sites through a number of factors:

Jan 1, 2019

By Michael P. Amsden

"THE ECSTALL CONCENTRATOR is situated adjacent to Highway 101 and the Ontario Northland Railroad, 15 miles east of Timmins, Ontario. Ore is delivered to the concentrator by rail from the mine, which is 17 miles northwest of the plant. Power and fuel are obtained from the hydro and natural gas lines which pass close to the plant site. Water is obtained from the Frederickhouse River, 6 miles east of the concentrator. The main concentrator building is a large structure 500 by 640 feet by 90 feet high and contains facilities for fine crushing, crushed ore storage, grinding, flotation, tin recovery, concentrate handling and reagent handling. Located in the same building are the machine shop, warehouse, metallurgical laboratory, pilot plant, men's change room, sample preparation area and an assay laboratory. The general concentrator layout is shown in Figure 47. Originally designed to handle 9,000 tons per day, the concentrator now treats 10,000 tons per day. Two different ore types are processed by selective flotation in three individual circuits to recover copper, lead and zinc concentrates. In 1973, another circuit was added to recover pyrite and tin concentrates from the combined zinc tailings of the three main circuits."

Jan 1, 1974

By L. D. Snyder, J. K. Russell

"The Lower Jurassic Iron Mask batholith intrudes Upper Triassic Nicola Group volcanic rocks in the Quesnellia terrane of southcentral British Columbia and hosts Cu-Au mineralization. The batholith comprises three mappable intrusive phases, including: Pothook gabbro to diorite, Cherry Creek monzodiorite to monzonite and Sugarloaf diorite. The Iron Mask hybrid forms a fourth mappable unit that makes up to 45% of the areal exposure in the batholith. It is highly variable in texture and composition and subdivided into three types; Type I and II have abundant (partially digested) xenoliths, many of which are derived from the Nicola Group, whereas Type III is xenolith-poor and shows extreme outcrop-scale textural diversity.Pothook and Cherry Creek rocks are similar in texture, mineralogy, whole rock and mineral composition and style of alteration. Contacts between the two can be intrusive or gradational. Rocks collected from these two suites have compositions that are permissive of a single magma batch, although simple crystal fractionation does not explain all chemical variations within and between the two suites. The Sugarloaf unit comprises a diverse group of amphibole-phyric rock types and is texturally and mineralogically distinct from Pothook and Cherry Creek suites.The Iron Mask hybrid represents progressive stages of physical and chemical interaction between Nicola Group country rocks and Pothook magma. Magmatic assimilation (selective or partial) is supparted on the basis of field relationships, petrographic observations, and REB compositional data. Thermal dehydration and partial assimilation of Nicola Group rocks by Pothook magma is shown to be a valid means of promoting early and extensive volatile saturation in the Iron Mask batholith."

Jan 1, 1995