Search Documents

By R. P. D. Graham

It is almost exactly two hundred years since the foundations of the mining and metallurgical industries in Canada were laid. There '."'as nothing spectacular about this early start. It had to do with the most basic phases of these industries-the mining of coal and iron ore, and the manufacture of cast and wrought iron. At several points along the coast of Cape Breton island, coal seams may be seen outcropping quite conspicuously, and it is probable that they had been observed, and possibly worked in a small way, in very early times. However that may be, these coal seams have the distinction of being the first in North America of which there is any printed record, reference to them appearing in a volume by Nicolas Denys which was published in Paris in 1672. Regular coal mining in the district did not commence until about fifty years later, however. The metallurgists started their operations along the north shore of the St. Lawrence river. Here, at many points between Montreal and Quebec, are to be found deposits of bog iron ore, and in 1 730 a furnace for smelting such ore was established on the St. Maurice river. The St. Maurice forges continued in operation until 1880, and throughout that long period they were famed for the fine quality of castings produced, and also for a-superior wrought iron.

Jan 1, 1924

By P. P. Sinha, D. N. Bhatia, B. R. Ghosh, R. K. Gupta

Medium carbon, low alloy, high-strength steels containing Ni, Cr, and Mo are used for the fabrication of various types of high-strength fasteners required for launch vehicle structures. Cold heading properties and response to hardening and tempering are the essential requirements of the material for fabrication and application, respectively. Combining these two requirements is essentially warranted in high-strength fastener-grade steels. Cold heading properties require ductility, which can be achieved through spheroidizing treatments. In the absence of a suitable spheroidizing cycle for medium carbon 3.8 Ni, 1.8 Cr, 0.3 Mo steel, experiments were carried out with a theoretical understanding of the alloy system. This paper presents the experiments and results obtained after a spheroidizing treatment, which was carried out to optimize the process. Hardness measurements were carried out and microstructural studies were conducted to assess the spheroidization process and to determine the optimal spheroidization parameters.

Jan 1, 2007

By Glenn Norris, Tyler Buckingham

"Gold recovery gains in the order of one to two percent have been realized in 2009 due to changes in the operation of the grinding circuits at Barrick Gold Corporation’s Hemlo - Williams Mill. The initiative known as “split milling” involves milling low grade open pit ore in one grinding circuit and higher grade underground ore in the other grinding circuit under different conditions.The philosophy of split milling involves processing higher grade underground ore at a lower throughput rate and a finer grind while milling lower grade open pit ore at a higher throughput rate and a coarser grind. Bench scale tests showed that the recovery relationship for underground ore sources was much more grind sensitive than that of open pit ore. This relationship proved to hold in the plant. The gold recovery gain due to finer grinding of the higher grade ore is much greater than the recovery loss due to coarser grinding on the lower grade ore. Since the majority of gold is being recovered at a higher rate, this results in higher overall plant gold recovery when compared to the traditional operation philosophy of blending the ore sources.The challenges for achieving the maximum benefits of split milling were two fold; the need to increase throughput on the open pit ore milling circuit and a means of grinding finer on the underground circuit. The former was met with an increase in SAG (Semi-Autogenous Grinding) mill ball charge, a basic “drill to mill” blasting campaign and changes to the primary gyratory crusher. The latter was met with a reduced SAG mill ball charge and a higher milling density. The resulting benefits in additional gold recovered are in the order of $3-5 million per annum.INTRODUCTIONThe Williams Mill processes ore from three different ore sources, the David Bell Mine (DB), the Williams Underground Mine (WUG) and the Williams Open Pit (OP). All three ore sources are located within the Hemlo camp in Northwestern Ontario adjacent to the Trans-Canada Highway. The Williams Mill was built in the mid 1980’s at which time it was designed to process 3,000 dry metric tonnes per day through a 22’ SAG mill in series with a 16’ ball mill. In 1988 a Mill expansion doubled the mill capacity by adding a second identical grinding circuit. A photo of the current grinding circuit can be seen in Figure 1. Today the Williams Mill processes an average of 8,000 tonnes per day of which approximately 60% is from the Williams Open Pit."

Jan 1, 2010

By Mohamed Ourriban, Stéphanie Somot, Éric Proulx, Jean-Sébastien Marois, Marjolaine Drouin, Paul Blatter, Ahmed Bouajila, Claude Gagnon

"The mining industry has to face increasing restrictions concerning the use of fresh water in Québec and throughout the world. Increasing recirculated water usage could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have a negative impact on mineral processing operations, thereby limiting the incentive for sustainable development initiatives. As a first step into selecting and testing remediation strategies, one of which being blending local waters, a mapping of process water quality (inorganic and organic fractions) allowed to locate zones in an industrial case study where fresh water is introduced into the circuit and to detect dissolution and precipitation zones. A complementary hydro-geochemical modeling study on water blends was also performed showing encouraging results towards the objectives of the project.INTRODUCTION The industry has to face increasing restrictions on the use of fresh water in Québec (Quebec Government, 2009) and throughout the world (Brown, 2003; UNESCO, 2006). The cost for the use of fresh water and for water management is highly variable and case-dependent (from 0.2 to up to 7 million dollars/year according to available private estimations, excluding the capital expenditure). It may be, or may become, significant for any plant; thus, risk assessment is of concern here. Using recirculated water could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have some positive and negative impacts on mineral processing operations (Janssen, 2003; Johnson, 2003; Rao and Finch, 1989). Negative impacts could limit the incentive for sustainable development initiatives. Water management strategies at mineral processing sites are supported both by a strategic plan and a water management plan. The strategic plan includes legal aspects, investment costs, potential benefits and various risk levels (Corder and Moran, 2006; Côte et al, 2006; Evans et al., 2006; MacIntosh and Merritt, 2003; McLellan et al., 2008; Merritt and MacIntosh, 2006; Robinson and Keddie, 2006; van Beers et al., 2007a; van Beers et al., 2007b; van Berkel, 2007). In practice, the strategic plan evaluates technical possibilities and costs of various scenarios, such as for example: bringing fresh water to the plant or recirculating waters, or using blends of both. Two important factors to consider in order to enhance the future production efficiency and to minimise risks are: the durability and the stability of the resource, both from quality and quantity points of view."

Jan 1, 2012

By D. Imeson, T. Grammatikopoulos, G. Pearse, M. Aghamirian, C. Mohns

"Spodumene mineral is a source of lithium for lithium ion batteries. Thus, the production of a spodumene concentrate with an approximate grade of 6% Li2O is targeted. Traditionally, spodumene is concentrated by froth flotation using fatty acid as the collector. Amine collector can also be used to float mica ahead of spodumene as required or feldspar from the spodumene tailings. Slimes have a negative effect on spodumene flotation and they are commonly separated by scrubbing and de-sliming prior to spodumene flotation. The main losses in spodumene flotation typically occur in cyclone overflow, scrubbing slimes, spodumene flotation tailings and mica concentrate. In recent years, dense media separation (DMS) is the main concentrating process in Australian spodumene operations. In these operations, DMS is efficient at generating coarse grain concentrates and rejecting large portions of silicate gangue, thereby directly reducing the milling cost. The ore should be crushed to 3/8” or coarser while further crushing is possibly necessary on the middling particles to scalp further spodumene. The DMS feed should be classified to remove fines (typically -0.5 mm particles). The final middlings and undersize fractions could then be processed by flotation. The main requirement in DMS operations is to have good spodumene liberation at relatively large grain size. This paper reviews the most significant DMS and flotation parameters in spodumene beneficiation. The treatments of different minerals in the spodumene ore are also addressed.INTRODUCTION A number of laboratory/pilot plant programs have been recently conducted at the SGS Lakefield site, sponsored by different clients. The main objective has been to develop a process flowsheet to generate a spodumene concentrate containing 6.0% or higher Li2O (~75% spodumene) suitable for producing lithium carbonate by a hydrometallurgical process. Depending on spodumene liberation size, dense media separation (DMS) can be an attractive option to produce a final high grade concentrate and to reduce the mass to be treated in the flotation circuit. In such a case, crushing would typically be performed in stages, with DMS separation to recover a spodumene concentrate and reject gangue minerals following each stage. DMS middlings and -0.5 mm fines can be processed by flotation to further recover spodumene. In the flotation process, coarse stage grinding minimizes the grinding cost and formation of slimes. In the majority of cases, a grind size (K80) of approximately 200 microns is sufficient for flotation. After primary grinding, mica, if present in an appreciable amount, should be floated to minimize interference with spodumene flotation. Desliming after scrubbing and high density conditioning are the key process operations prior to spodumene flotation. Spodumene can then be floated from silicate gangue minerals with a fatty acid or a mixture of fatty acid and petroleum sulfonate at slightly alkaline pH. Subsequently, feldspars can then be floated from the spodumene tailings."

Jan 1, 2012

By David Whalen

Mobile equipment in oil sand mining operations experience more maintenance problems than similar equipment in other surface mines, due to soft underfoot conditions. Oil sand properties are known to vary with temperature, bitumen content and previous loading cycles. One of the challenges is the widely variable underfoot pressure which supports shovels and trucks. In the case of a heavy hauler driving on in-pit roads, each tire is supported by a different ground stiffness resulting in an apparent uneven surface. Driving over uneven ground causes twist in the truck frame, which is transmitted to the dump body. Through a finite element analysis of a haul truck dump body, it was shown that slight frame twists produce localized stresses in the intersections of the floor stiffeners. These stresses are at times greater than those resulting from the maximum ore weight and are primarily responsible for cracking in these intersections. Syncrude maintains high quality haul roads, which are constructed of gravel, and makes every effort to keep the shovel pit roads as smooth as possible. This problem cannot be avoided through operational practices only and must also be accounted for in the design of haul truck bodies.

May 1, 2003

By L. Nichols, H. Keele, K. Czajewski

"The oil sands industry in northern Alberta disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called consolidated tailings or composite tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long-term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long-term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities.Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are longterm stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface.The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process."

Jan 1, 2008

By James A. Brown, Marius Botha, Christopher A. Fleming

"The technical and economic feasibility or re-processing hundreds of millions of tons of tailings in a number of historic gold tailings dams in the Witwatersrand area of South Africa is being investigated. The objective is to recover uranium and residual gold from the tailings, as well as to oxidize the sulphides to eliminate long term environmental liabilities associated with acid mine drainage. The tailings from the re-processing plant will be re-deposited in a new area far from urbanization, allowing for the rehabilitation of the real estate currently occupied by these historic tailings.The first step in the process involves a mild-regrind and mild acid leach of the tailings (pH 2.5 to 3.0) to dissolve up to 40% of the uranium. This uranium is recovered directly from the pulp by resin in pulp (RIP) with a strong base resin. The RIP tails are then treated by flotation to recover a rougher pyrite concentrate, and flotation tailings that are discarded. The rougher concentrate is cleaned to produce a final pyrite concentrate and cleaner scavenger tailings, and the pyrite concentrate is oxidized in an autoclave to leach uranium and generate acid. The autoclave discharge is combined with the cleaner scavenger tails, and the acid and ferric ions generated in the autoclave are used to leach more uranium and oxidize more sulphide in the cleaner tails. The product from the concentrate leach circuit is processed by resin in pulp for uranium recovery, followed by neutralization, cyanidation and carbon in pulp for gold recovery.The rougher float tails may be further treated to recover gold that was not recovered in flotation, but which had been liberated from the old dumps by natural oxidation of some of the pyrite over many decades. The float tails would be neutralized and treated by cyanidation and CIL to recover this liberated gold.All parts of the flowsheet have been extensively tested in the laboratory, and the critical elements of flotation, pressure oxidation and resin in pulp have been demonstrated in pilot plants. The results of the hydrometallurgical investigations are presented here."

Jan 1, 2010

By Norman O. Lotter

Drill core is preferred as the sample material for metallurgical and mineralogical characterisation and flowsheeting of an orebody. The question arises as to how to do this at the economic optimum, since geologists have several other strategic uses for their drill core. The limiting factors are the cost of extra drilling for the metallurgical testwork and the need to preserve the drill core record. In this study, the representative sampling of drill core at an economic optimum for metallurgical testing is addressed. This phase of the drill core work is preceded by earlier drill core characterisation - for which other appropriate sampling protocols are used - that has provisionally categorised the orebody into geometallurgical units. In stratified sampling of drill core, use is made of a version of the stratified approach to compound distributions proposed by Cochran in 1946. Use is made of Gy’s 50-piece minimum sample mass model to estimate minimum requisite sample mass. In the case where sampling and testwork are required on a Lifeof- Mine blend of a given ore deposit, whereby defined ore types or geometallurgical units are present, the sample mass requirement is significantly reduced by working from drill-core at the geometallurgical unit level. A case study using Raglan drill core is discussed. Using nickel as an indicator paymetal, and sampling at a fundamental variance level of 8%, the minimum sample masses for disseminated sulphides, net-textured sulphides, and massive sulphides are 3.80, 7.37 and 4.39 kg respectively. When the same drill-core is sampled as a Life-of-Mine mixture without knowledge of the geometallurgical units, the minimum sample mass increases to 84.28 kg. It is thus possible to assemble a representative Life-of-Mine sample of drill-core more economically, at the same time validating its representativity. Equivalent calculations for copper, platinum and palladium are discussed, with outcomes consistent with this finding. When all four paymetals are considered, one selects the largest minimum mass out of all four cases. This results in minimum sample masses of 11.67, 74.90 and 175.16 kg for disseminated sulphides, net-textured sulphides and massive sulphides respectively. The simulated Life-of- Mine blend would require a minimum sample mass of 377.33 kg to cover all four paymetals.

Jan 1, 2010

By Joey Hoang, Robert Johansson, Tapani Keronen, Mikael Jåfs, Jani Jansson, Mikko Korpi

At the Copper 2016 conference in Kobe, Japan, Outotec introduced a vision for the year 2020, wherein smelting would make use of four digital cornerstones: intelligent instruments, advanced process control, improved information management and transparency of and access to data. Since then, this vision coined the phrase “Fully Automated Smelter” with the mission promising a concept where no manual actions from human operators would be needed during normal smelter operations. Replacing repetitive physical work, collection and analysis of everyday production data has a great potential for further automation and will provide productive ways to improve efficiency and safety of smelters in the future. Therefore, a lot of emphasis has been put into developing solutions to automate these tasks and to move people out of harm’s way. A lot of new equipment, systems and optimization tools are under development. In addition, a lot of effort is going into developing dynamic process models and advanced control systems to interface with the plant automation systems. The goal is to integrate all these concepts to meet Outotec’s Fully Automated Smelter vision. This paper will cover these latest achievements toward this vision and introduce the near-future of digital smelting. INTRODUCTION As is well known already, the humankind is currently experiencing a change, extent of which is broadly studied by the governmental, educational and industrial institutions and parties. The wellbeing and quality of life have traditionally been improved alongside the developments in industrial production, which is now about to enter its fourth revolution. Therefore, the current change is often described as fourth industrial revolution, or industry 4.0 (or industrie 4.0, as named by Acatech, 2013) and can be considered anything from small incremental development to a ground-breaking global reset that will affect everyone’s lives. Many seem to agree, that the scale of change will indeed be big, even significantly bigger than the three industrial revolutions before it (Pellini, Weyrauch, Malho & Carden, 2019; Geissbauer, Vedso & Schrauf, 2016; Jansson, Bjorklund, Lahtinen, Heinonen, Jafs & Fagerlund, 2016).

Jan 1, 2019

By J. E. Nesset

"Significant progress has been made over the past few years on characterizing and understanding the hydrodynamic properties of frothers and collectors and their effect on flotation performance. This new understanding of the relationship between chemistry and hydrodynamics has dramatic implications for how flotation circuits should be controlled and optimized. Previous work has shown that choosing a frother of the right ‘strength’ is critical to the optimization process, and the work and discussion presented here serve to strengthen the argument. In addition, we know that collector chemistry will also influence hydrodynamic properties and needs to be taken into consideration. To achieve the desired outcome, the overall system of reagents and operating parameters must be considered. This paper describes and discusses some of the findings from recent research on frother and collector chemistry effects (on hydrodynamics), and how this knowledge can be used to improve flotation performance. Examples from plant experience are discussed.INTRODUCTIONFrothers perform various functions in flotation but the primary ones are control of bubble size in the pulp zone and stabilization of the froth zone. Laskowski (2003) was among the first to try to capture both roles in characterizing frothers in order to provide a basis for frother selection for a given duty, as well as to explore the link between function and frother chemistry (structure). The method he used requires bubble size data and a frothing index; the procedure has been simplified by Cappuccitti and Finch (2008) using gas hold-up to substitute for bubble size, and froth height (without overflow) as the froth stability metric. The gas hold-up/froth height relationship will be referred to as ‘hydrodynamic characterization’. Essentially, the gas hold-up parameter reflects the sum of the hydrodynamic conditions in the pulp phase (water in this case), i.e. the effect of bubble size plus the apparent impact of the water surrounding the bubble due to the frother (Finch, Nesset and Acuna, 2008). Similarly, the stable froth height parameter reflects the sum of hydrodynamic conditions in the froth, i.e. the effect of bubble size undergoing coalescence plus the influence of the water in the lamellae and Plateau borders between bubbles. It could be argued that the gas hold-up/froth height relationship is a superior one to simple bubble size/froth index for discerning differences in frother behaviour"

Jan 1, 2010

By Terry Keough

Contents for discussion ?Current liner technology ?Innovation of magnetic products ?Development of magnetic wear liners ?Installation and change out method ?Uses and capabilities ?Internal wear liners ?Summary Vulcanized rubber ?Many of you are familiar with using vulcanized rubber to provide wear protection on mining equipment. For years, this was the standard for most mining equipment, and mines spent a lot of money fabricating and lining steel equipment.

May 1, 2010

By Chris Fleming, John R. Goode, James Brown

"Data will be produced from two uranium feasibility studies that were conducted in 2008, both involving uranium recovery from leached slurry by resin-in-pulp (RIP) with strong base resins. Excellent metallurgical results were produced in RIP pilot plants in both studies, and the loaded resins were eluted with strong sulphuric acid and recycled to RIP in an integrated process. Resin losses by either abrasion or mechanical breakage were immeasurably low.Metallurgical results from these two campaigns will be presented, along with an economic analysis of RIP versus the alternative process of CCD or filtration and solvent extraction.INTRODUCTIONThe recovery of uranium directly from pulp with strong base resins in RIP contactors was practiced commercially in the USA in the 1960s, but the process never established itself as a viable alternative to solid/liquid separation and solvent extraction. This was due mainly to the necessity to do a sand-slime separation partially resulting from the unavailability of coarse resin beads, inadequacies in the design of the RIP contactors and screens to separate resin from pulp, as well as problems with the strength and durability of resins in agitated pulps.There have been significant advances in the last 30 years in each of these areas. All the commercial resin manufacturers are now producing very tough, durable, strong base resins, and are manufacturing them in a large bead size that is better suited to RIP applications. In addition, with the emergence and wide spread implementation of the carbon in pulp process in the gold industry in the 1980s, many innovative techniques for preparing leached slurries and separating carbon from pulp have become firmly established. These techniques have proven to be equally applicable to resin separation from pulps in RIP contactors."

Jan 1, 2010

By Paul Staples, Chris Morley

"The development of the Cerro Verde, Amplats Mogalakwena and Boddington projects over the last few years has helped to establish the use of high pressure grinding rolls (HPGR) in comminution circuit designs in large-scale hard-rock applications. The increasing acceptance of this innovative and sometimes controversial technology has had the natural effect of prompting many other new projects to examine HPGR as an alternative to the established, usually SAG-based, comminution circuit design approach.At the current stage of development of the technology, HPGR-based circuit capital costs are generally higher than for the equivalent SAG-based circuit, so that HPGR must offer sufficient operating cost benefits to offset the additional capital costs over an acceptable pay-back period. It is usually necessary to undertake comprehensive project-specific trade-off studies to quantify this effect.This paper describes the processes involved in the execution of a typical SAG-HPGR trade-off study, from the preliminary assessment of ore characteristics and project criteria, through testwork, circuit modelling, equipment selection and cost estimates, to a project-economics comparative assessment of the options. The trade-off study determines both the technical feasibility of the respective technologies and their commercial viability in the given project setting.The paper concludes with a cautionary note to the effect that, while HPGR has many potential benefits, it is not a panacea, and that, for some ore types and project conditions, the more established conventional technologies are often more appropriate."

Jan 1, 2010

By K. Swedburg, M. Samuels

"The New Afton concentrator was commissioned in June 2012, reaching the design milling rate in September 2012. By late 2013, through a campaign of optimization and de-bottlenecking, it was recognized that the installed plant was capable of greatly exceeding the design throughput of 11,700 tpd. Because the value of the metal contained (by increasing the plant feed rate) exceeded the offsetting losses of copper and gold recovery (as the operation moved to a coarser grind), the concentrator feed rate was strategically increased with support of New Gold, while the operations team was given a mandate to evaluate, and then implement, flow sheet options that could re-establish the original design criterion grind target and achieve the corresponding improved recovery. Broadly, the two options implemented were the addition of a tertiary grinding stage consisting of Metso Vertimill® prior to rougher flotation (in order to address the grinding required at increasing throughput by increasing the power), and the addition of three Woodgrove Staged Flotation Reactors (SFR) added to the cleaner circuit after regrind of the rougher concentrate (to address the increased mineral loading to the cleaner circuit). Through test work, it was anticipated that the SFRs would be capable of achieving final concentrate grade in a single pass without the integration of recirculating loads, a strategy sometimes referred to pre-cleaning. This paper describes the expectations generated for the Woodgrove SFR unit operation through pilot plant testing on site, and compares those results with the performance of the expanded circuit that exceeded the original design criterion of P80 160 µm, which was commissioned in the second quarter of 2015.INTRODUCTIONThe New Afton concentrator, located near Kamloops, BC Canada, commenced operation in June 2012. The mill achieved the design throughput of 11,000 tonnes per day average during the month of September 2012 and, following various operational optimization efforts (O’Hara et al, 2015), achieved the design p80 grind size of 160 µm at the design milling rate in July 2013.During August 2013, trials were carried out to determine the throughput rate limits of the mill circuits and to evaluate mill metallurgical performance at higher rates. Milling rates up to 15,500 dmt per 24 hours were achieved during this trial, demonstrating potential capability for sustained milling rates exceeding the nominal design capacity. As was expected, the higher milling rates resulted in a coarsening of the grinding circuit product size, and resulted in marginally lower recoveries in the rougher flotation circuit. Despite the lower recoveries, the higher milling rates resulted in higher metal production and the financial analysis favored running at rates of at least 13,000 tonnes per operating day, with the higher cash flow in the near term offsetting the value of metal production loss at the end of the mine life (due to the short term increase in the rate of reserve depletion). Milling rates were sustained above 13,000 tonnes per day through the second half of 2013, and increased above 14,000 tonnes per day by mid-2014 (Figure 1)."

Jan 1, 2016

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

By Gavin A. Hunt

In order for mines to operate profitably throughout their life it is important to monitor and maximise ore recovery. A common problem facing many mines is the underestimation of clay type and its distribution in ore at the mine face, blast hole or in the ore stockpile. Too much clay entering the heap leach ore stream for example causes a dramatic reduction in heap leach efficacy and or increased leaching times. The end result is poor leaching performance and much reduced metal production. Poor clay identification and quantification is attributable to many factors, including costly and slow off-site mineral analysis techniques, such as XRD, XRF and petrology, the visual and subjective limitations of the core logging geologist and a lack of suitable low cost, high throughput mineral logging instruments. To get round these problems a new, non-contact, imaging spectrometer - the SpecCam - was developed by Spectra-Map Ltd, to allow high throughput identification and quantification of minerals from mineable material. Its novel imaging design can collect millions of data points (pixels) per day; each pixel contains spectral information that allows a wide variety of mineral types, including the smectite and illite clays, and phyllosilicates such as talc and kaolin, to be identified. Because all the ore can be imaged a much more reliable mineral log can be made. Hence, mapping changes in mineral composition - related to variations in phenocrysts, macrocrysts, veining or wall rock - is possible. Examples of SpecCam data from Goldfields Cerro Corona Porphyry stockpile and from Rio Tinto?s Argyle Diamond mine illustrate the mineral identification and quantification capabilities of the SpecCam. More importantly, for the first time very accurate % abundances for the different minerals can be obtained using an image-based modal count technique. The modular design of the camera, plus its extremely flexible high speed filter, mean that the SpecCam can be easily installed on different equipment, each one suited to different ore recovery problems. For example the SpecCam can be used on an automated portable logging frame to measure drill core, RC chips, hand samples or powder, or alternatively installed on a Geotek multi-sensor core logger for high-throughput, automated logging of drill or blast hole core using co-registered multi-sensor data. An exciting recent development has been the installation of the SpecCam on CommoDas ore sorting equipment, used around the world for 24 hour mill-feed monitoring and automatic ore sorting. Real-time ore sorting decisions can be made as material is monitored on a conveyor belt running at 3m s-1, from which the ore can be automatically sorted into high-grade, low-grade or waste streams for example. The three installation options for the SpecCam mean that most mineral analysis and automated core logging or ore monitoring needs can be met at the mine. For the first time rapid and automatic mineral identification and accurate quantification can be made. All of which allow the mine geologist or metallurgist to make important decisions about maximising the metal recovery process.

May 1, 2007

By Michel Fontaine, Bruno St-Cyr

"The mission of the CENTRE DE RECHERCHE INDUSTRIELLE DU QUEBEC (CRIQ) is to stimulate economic development by guiding businesses in their pursuit of innovation.With a comprehensive approach to their needs, CRIQ provides businesses with expertise based on the most recent developments and insights in the fields of:Research and Development ServicesAutomation and production processesDevelopment of industrial equipmentEnvironmental biotechnologiesTesting and Product Qualification Services Industrial and Technological Information ServicesConsultancy and competitive intelligence servicesIndustrial information bankStandardization ServicesElaboration of standards and product certificationSystems registrationEXPERTISE COMPETENCE, INNOVATIONSince its founding in 1969, CRIQ has been involved in over 100,000 projects. The results of its research and development services have enabled it to build over one hundred pieces of equipment, almost all still in operation today. CRIQ has been and remains the driving force of innovation and expertise on the industrial scene, offering highly competitive solutions to a clientele from numerous industrial sectors.CRIQ became a crown corporation operating on a commercial basis on June 30, 1997. This change in its corporate structure has enabled it to put a marked emphasis on trade and implement an array of new operational practices.The formation of marketing companies with private partners, the opening up to corporate business and international markets, the new directions for internal research and the strengthening of its marketing component are among the activities CRIQ has initiated over the last fiscal year to finally reach its cruising speed."

Jan 1, 2000

By G. Lipsett, S. Dessureault

Information technology (IT) initiatives in the past have tended to be sold on their ability to maximize resource output and return on capital by allowing assets to be used more effectively and efficiently. Many IT projects fail, not delivering return on their investment. This is known in the IT industry as the “productivity paradox,” where increasing investments in IT do not result in comparable increases in productivity. Experiences and studies of most business sectors reveal that this paradox is rooted in the false assumption that more IT spending automatically results in financial benefit, whereas the benefits are in how effectively IT is used. Most business sectors have accepted that re-engineering of processes is required to gain the full benefits promised of IT. A mining operation has organizational processes similar to most business sectors, but unique operational processes. The lessons of changing business practice in more common business processes, such as inventory control and customer-supplier relationships, can be adequately transposed into a mine setting. The unique operational processes in mines, in turn, require unique redesign efforts. Several enabling information technology opportunities have recently become available, such as more integrated mine production management systems and tactical manager training simulators. This paper reviews some of the latest IT products and outlines the processes and kinds of change that will be required in order to benefit from these new investment options.

Jan 1, 2009

By Anil K. Beersing

Effective drainage systems are required for reclamation of mine-disturbed areas to control surface water runoff and avoid excessive erosion. For the conventional structural design approach, armouring material necessary to satisfy the design criteria should not move during the design flood event since displacement would uncover the erodible underlying materials. This paper discusses an alternative geomorphic approach for designing drainage channels and watershed landscape. The approach is based on quantitative studies of geomorphic processes operating in a watershed. A design based on the geomorphic approach replicates the configuration, channel regime, sediment volume and hydrology of natural and mature drainage systems. Movement of some armouring material is acceptable in such an approach because the channels are allowed to mature by natural degradation and aggradation, with erosion rates comparable to the natural environment. The key advantages of a geomorphic approach over a purely structural approach include reduced sizes of armouring material, geomorphologically sustainable landscapes, ?walk-away? or maintenance-free design and reduced liability in the future. The geomorphic approach is illustrated using the example of a coal mining operation in northwest U.S.A. The paper discusses field data collection, design criteria, typical design details, and construction methods.

Apr 1, 2005