Search Documents

Pillars are used in various forms in underground mining. For several decades pillar design has been an issue in both soft and hard rock underground mining. The major use of pillars is in room-and-pillar type mining. Pillars are critical structures in the production levels of block cave mines. With most mines leaning towards the use of block caving for ore extraction today, pillar design has become even more important. Empirical pillar design is popular. The use of numerical modeling is becoming more common in the design of underground mine pillars. A critical review of both the empirical and numerical modeling approaches to the design of underground mine pillars reveal some fundamental flaws. In general, pillar design approaches often assume the pillars are vertical, and are subjected to pure compression. Pillar failure criteria are then based on this assumption. Most papers on numerical modeling for pillar stability assessment use vertical pillars. This paper shows that where pillars are not subjected to pure compression the empirical pillar design approaches are inadequate, and that when using numerical models for the assessment of pillar performance, more care is needed in the determination of the average pillar stresses. The practice of relating field scale pillar strength to laboratory scale intact rock strength determined from conventional laboratory compression tests in empirical design equations is misleading when pillars are inclined or subjected to compressive and shear stresses. New data is added to the hard rock empirical pillar stability chart, and it is shown that it is misleading to conclude that failure of pillars with width to height ratios greater than 2.3 should not be anticipated. New empirical pillar design charts are presented for pillars at various degrees of inclination for different ko-ratios.

Aug 1, 2013

By G. M. Ritcey

The recovery of copper from low-grade solutions res ulting from dump leaching is well known, whereas the recovery from highly concentrated copper solutions has not been practiced. This paper discusses the use of Ashland Chemical's Kelex 100, a substituted quinoline, for the recovery of copper from solutions resulting from leaching copper-nickel concentrates. A flow sheet is described, and an economic comparison shows Kelex 100 to be superior to either the LIX 64N or LIX 70 reagents of General Mills for the recovery of copper.

Jan 1, 1973

By A. G. Darnley

"The Geological Survey of Canada is devoting consider-able effort to finding ways to make airborne radiometric measurements both quantitative and reproducible. Equipment has been designed by Atomic Energy of Canada Ltd. to provide high count rates in order to minimize statistical uncertainty, this being essential to justify applying terrain clearance and Compton scattering corrections to the data. Correction factors have been determined experimentally and can be applied automatically. Considerable ground work has been undertaken in parallel with equip-ment development in order to determine field parameters.Two airborne gamma-ray spectrometers are described. One is based on three 5-by 5-inch Nal(Tl) detector crystals and is used in a helicopter; the other employs twelve 9-by 9-inch detectors and is used from a Skyvan aircraft. The former is being used to investigate the range of radiometric response from specific rock types, and for the correlation of ground and air measurements; the latter has completed initial trials and will be commencing experimental surveys during 1969.Results are given to show the comparative sensitivities of the various detector sizes, and operational requirements for a gamma-ray spectrometer survey are discussed briefly."

Jan 1, 1970

By I. C. Brown, J. F. Henderson

"IntroductionThe Yellowknife greenstone belt lies along the west side of Yellowknife bay on the north shore of Great Slave lake, some 600 miles north of Edmonton, Alberta. The producing gold mines along the belt include the Con-Rycon and Negus which came into production in 1938 and 1939, and the Giant Yellowknife, which followed in 1948. In addition to these, the Akaitcho and Crestaurum mines are potential producers and there are several promising prospects.Early geological work along the belt was done by A. W. Jolliffe who first recognized a number of great faults, the largest of which is the West Bay fault with a horizontal movement of more than 3 miles. In 1943, A. S. Dadson, following an examination of the Giant-Yellowknife property, advanced the hypothesis that Baker Creek valley was underlain by a series of major gold-bearing shear zones. Subsequent diamond drilling in 1944 bore out the correctness of this view and outlined the great ore-bearing shear zones that are now being developed and mined by Giant Yellowknife Gold Mines. Near the south boundary of the Giant property, the shear zones are cut off by the West Bay fault. This prompted Neil Campbell, District Geologist for the Consolidated Mining and Smelting Company, to make a detailed study of the geology along the West Bay fault in the hope of finding the faulted extension of the Giant shear-zone system on the west side of this fault. In this he was entirely successful. By careful geological mapping he matched several faulted diabase dykes on both sides of the fault and, knowing their dip, determined the horizontal and vertical components of movement along the fault. Subsequent •diamond drilling based on Campbell's work located the presumed correlative of the Giant shear-zone system on the Con-Rycon and Negus properties, where it has been named the Campbell zone or system. At the present time, all production at the Negus Mines property is coming from orebodies along the Campbell zone."

Jan 1, 1950

By J. D. Clucas, D. B. Dreisinger

"The Starved Acid Leach Technology (SALT) has been developed by Search Minerals to extract nickel and cobalt VALUES (from nickel laterite ores (saprolites) and Caron plant residues. The technology consists of sulfuric acid atmospheric leaching of the ores or residues followed by neutralization and recovery of nickel and cobalt. The acid addition is carefully controlled to maximize nickel and cobalt extraction while minimizing overall consumption of acid by various gangue reactions. The final recovery processes can be tailored for maximum economic benefit. The use of resin-in-pulp processing is advocated as the most cost effective method for initial recovery of nickel and cobalt from lower grade materials. INTRODUCTIONCommercial processes for laterite ore treatment vary according to laterite type and local conditions. The two general categories of laterite ore are saprolites and limonites.Saprolites are generally treated by pyrometallurgical processes for reduction of nickel to matte or ferro nickel alloys. The high cost of drying, chemical reduction and electric furnace smelting requires that the saprolite grade for economic processing is of the order of 1.8% nickel or higher. There are of course large amounts of saprolite that fall below this “cut-off” grade that are not currently economic.Limonites can be treated by the Caron Process which involves drying of the ore, a reduction roast of the whole ore to reduce nickel and cobalt (and some iron) to the metallic state followed by ammonium – ammonium carbonate solution to leach nickel and cobalt. Nickel and cobalt recovery are low (70-85% for Ni and 20-50% for Co). The Caron plant tailings therefore contain high levels of unrecovered nickel and cobalt. Relatively few plants have used the Caron Process and new installations are not anticipated due to the high energy cost of drying and reduction roasting. Nevertheless, plants in Brazil (Niquelandia), Australia (Yabulu) and Cuba continue to operate.The high pressure acid leach (HPAL) process was pioneered at Moa Bay in Cuba in the 1960’s in the treatment of limonites. In the 1990’s the HPAL process was touted to revolutionize the nickel industry with low capital and operating costs for new installations. Murrin Murrin, Cawse and Bulong in Australia were started and in each case the technical difficulties of operating at extreme temperature and pressure conditions and the challenges in “ramping up” a complex hydrometallurgical facility conspired to cause these plants to fail economically. At present, Cawse and Bulong are closed and Murrin Murrin continues to operate after undergoing a financial restructuring."

Jan 1, 2012

"An unparalleled growth in the Canadian coal industry in 1970 coincided with increasing awareness by Canadians of their environment and their geography with its accompanying transportation factors. R and D on coal moved with greater emphasis toward solving problems in these areas as well as continuing with strong interest in coal preparation, carbonization, combustion, ""weathering'', spontaneous ignition, storage, exploration and geology. Long-range ""basic"" research was not forgotten in that work continued on coal-based carbons, coal chemistry and agrobiological uses for coal. This paper reviews the status of these many areas of coal research at the beginning of the seventies and takes note of some of the more significant legislation and projects brought to the author's attention. No attempt is made to itemize or to describe in detail all the worthwhile projects, many of which are reported elsewhere."

Jan 1, 1971

By C. George Miller

"As the influence of governments has become more widely felt, the use of research techniques to analyze policy has increased. Mineral economics, as one of the foundations of mineral policy research, has grown accordingly. Policy research and analysis has been carried out within governments, university departments and the private sector. Each of these institutional environments has characteristics which influence the topics of study, the approach, the methodology and the output of the research. A brief survey of recent research activities provides illustrations of trends and developments occurring within this organizational framework.A radically different organization, the independent research institute, has begun to make an impact on policy research in recent years, and will have an increasing importance in the future. Combining certain features of the traditional research organizations, it nevertheless has important differences which are essential to its effective functioning. An overview of the formation, goals, organization and operation of one such institute is presented."

Jan 1, 1976

By G. M. Scamans

In the past ten years there has been considerable penetration of aluminum automotive body sheet (ABS) into automotive structures. The exponential increase in demand is resulting in major investments in heat treatment and finishing capacity across the globe. Line speed and tonnage throughput is limited by the continuous heat treatment (CHT) floater furnace rather than the cleaning and pretreatment section where electrolytic treatments that offer higher line speeds should come into favour and roll coating of pretreatment should predominate. The capacity limiting surface texturing pass will either be eliminated or moved to the finishing line or a dedicated mill. The key to making aluminum both embedded carbon and cost competitive with steel for more and more affordable classes of vehicles lies in recycling of both prompt scrap and, in the longer term, end of life vehicle scrap. For the first time scrap separation technology is available that can compete effectively with hand sorting and can sort aluminum shredded vehicle scrap into wrought and cast alloys and then into individual alloy groups. The challenge is to use more end of life scrap in alloy formulation whilst at the same time extending the property range in terms of both strength and formability.

Jan 1, 2015

By M. A. F. Fedikow, D. A. Baldwin, C. Taylor

The Agassiz Metallotect and the Johnson Shear Zone represent two metallogenetic fea tures located within the northern and outhern belts, respectively. of the Aphebian-aged Lynn Lake greenstone belt in northern Manitoba . Numerous gold occu rrences are associated with these two regional features . The tratabound Agas iz Au-Ag deposit with 2.9 million tonnes of 5.2 g/tonne Au and 11.8 g/tonne Ag. occurs within the Agassiz Metallotect. The stratigraphic sequence characterizing the Agassiz Metallotect comprises interlayered ox ide. silicate and sulphide facies iron formations, biotite-rich and siliceous siltstones. and a high Mg- i-Cr basaltic rock that ha previou ly been identified as tholei itic picrite. These rocks can be traced in outcrop and by their INPUT and gradiometric signature for 65 km. The Johnson Shear Zone is an ill-defined 35 km long zone of strucwral disruption that crosscuts volcanic. sedimentary and intrusive rocks and contains numerous vein-type gold occurrences. Both of these metallotects are characterized by their low level of exploration activity and as a result offer excellent residual exploration potential. Rock, basal till and vegetation geochemical techniques applied in the vicinity of the Agassiz deposit indicate the presence of trace element dispersion halos associated with the mineralization. The halos define an exploration target larger than the mineralized zone. Gold occurrences within the two metallotects are described with emphasis on the Agassiz Au-Ag deposit . A wide range of gold occurrence-types is documented including syngencticstratabound , epigenetic-replacement and epigenetic-quartz vein .

Jan 1, 1986

By R. J. Enright

Eight mines in canada and three in Australia were visited between September 1987 and Februacy 1988. All mines had encountered problems with sulphide dust explosions and had introduced defence mechanisms to prevent or limit the extent of these explosions. Techniques included dispersion of limestone by various methods, use of water foggers, placing of water and inert stenuning in blast holes, and removal of settled dust to prevent secondary explosions. The techniques were evaluated and it was concluded that certain practices should be modified or discontinued as they were of little value in preventing dust explosions.

May 11, 1988

By M. Cai

"It is well known that Peak Particle Velocity (PPV) plays a critical role in triggering rockburst damage in burst-prone underground mines. To estimate the PPV distribution around excavations, advanced numerical modeling can be used. In wave propagation numerical modeling, velocity field is often assumed to be uniform around an excavation. However, it is observed that wave velocities near mine openings are not constant, but rather non-uniform. Wave velocity in a rock mass depends on many factors such as rock quality and confinement. In particular, confinement has a large influence on wave velocity. The confinement around an excavation is low at the wall boundary and increases gradually and reaches a constant value far away from the excavation boundary. Hence, stress redistribution due to excavation will have a profound influence on wave propagation in underground mines. A better understanding of the influence of excavation effect on wave propagation helps to interpret the field observation of rockburst damage and improve mine safety. For this purpose, a non-uniform velocity model need to be constructed and the influence excavation effect should be taken into account in numerical wave propagation modeling.In the present study, a non-linear velocity model is developed firstly by considering the influence of confinement on wave velocity. This model links wave velocity to confinement explicitly. A coupled numerical method is then developed and used to study the seismic wave pattern around excavations in underground mines. Two codes, FLAC and SPECFEM2D, are coupled in the analysis. The motivation of developing the FLAC/SPECFEM2D coupled approach is to take merit of each code, such as the stress analysis capability in FLAC and the powerful wave propagation analysis capability in SPECFEM2D. The coupling process is realized through three steps: (1) static stress redistribution around an excavation is analyzed in FLAC; (2) data for coupling analysis, such as non-uniform velocity field (based on the new developed velocity model), mesh, absorbing boundaries, etc., are generated by FISH functions in FLAC and passed to SPECFEM2D; and (3) wave propagation modeling is performed in the SPECFEM2D considering a fault-slip seismic source. Because stress redistribution around the excavation is considered, non-uniform velocity field for the SPECFEM2D model can be obtained and this is a notable feature of this study. Very large difference in the S-wave response in these two modeling approaches with uniform and non-uniform velocity fields can be seen from the modeling results.Using the FLAC/SPECFEM2D coupled modeling approach, accurate velocity models can be constructed and this in turn will help to produce accurate PPV distribution around the excavations. Accurate PPV contours can be used to identify high rockburst risk zones for improved dynamic ground support strategy."

Jan 1, 2015

By James Kear, Romain Prioul, Robert G. Jeffrey, Andrew P. Bunger, Dimitry Chuprakov

"Unconventional gas and geothermal reservoirs are typically naturally fractured and therefore the challenging problem of hydraulic fracture (HF) growth through naturally fractured rocks is an important issue especially for the development of accurate predictive HF models. This paper presents results from laboratory experiments in which HFs have been created in both sandstone and crystalline (gabbronorite) rock specimens such that they impinge either orthogonally or at an oblique angle on an unbonded, machined frictional interface. Depending on the conditions of each experiment, the fractures either cross or are blunted at the interface. The growth behavior was ascertained for these experiments based on a synthesis of the injection pressure record, active ultrasound monitoring, and direct post-experiment inspection of fractured specimens. From these experiments we observe: 1) A contrast between direct crossing and crossing with an offset for orthogonal and oblique intersection, respectively, 2) Apparent independence of crossing/blunting behavior on the friction coefficient for orthogonal intersection, 3) Dependence of the stresses required to promote crossing on the intersection angle between the HF and NF, 4) Existence of cases in which the hydraulic fracture crosses but then essentially ceases propagation such that all fluid is diverted to the interface. INTRODUCTIONHydraulic fracturing is a vital technology used to increase the productivity of oil, gas, and geothermal wells. Predicting hydraulic fracture (HF) growth is, in turn, critical to design of hydraulic fractures that grow to the desired length, accept the desired amount of proppant, and remain contained in the reservoir without unwanted height growth into surrounding layers (e.g. Economides and Nolte, 2000). The importance of HF modeling has prompted 6 decades of research during which simulators have become more efficient, more accurate, and have addressed a growing range of complexities (see review of e.g. Adachi et al., 2007).One of these complexities is the interaction between HFs and mechanical discontinuities such as natural fractures (NFs). Efforts in this area have been mainly driven by development of unconventional (i.e. low permeability) oil and gas resources because essentially all viable low permeability reservoirs, including shale gas/oil reservoirs, are naturally fractured to some degree (King, 2010). One of the most important questions for developing effective HF stimulation strategies in these reservoirs is whether the hydraulic fracture(s) is/are expected to be single-stranded or whether interaction with the NFs will lead to network-like growth. The basic building block for numerical simulators that can address this question (such as Kresse et al., 2013 and Weng et al., 2014) is whether an HF that intersects an NF will cross the NF or whether its growth will be captured by the NF so that additional fluid injection pressurizes the NF but does not generate ongoing growth of a new HF. These scenarios, including subcategories such as crossing with an offset, have been recognized for several decades (Daneshy, 1974; Warpinski and Teufel, 1987, and as recently reviewed and expanded by Chuprakov et al., 2013)."

Jan 1, 2015

By P. Groleau, O. Tavchandjian, D. Marcotte

In open pit mining, each small mining unit (SMU) is selected for mill processing based on an estimate of its true grade. The estimation is usually done using analyses of cuttings from blast holes within that SMU. One common estimator used for selection is the arithmetic average of within-SMU samples. This estimator is conditionally biased. The effect of a conditional bias is to overestimate the profit really recovered from the deposit. For this reason, a conditionally unbiased estimator is preferable. Increasing the number of samples generally improves the accuracy of the estimation (and diminishes the conditional bias, if present, of most estimators). However, there exists a practical limit where an additional sample does not improve the estimation sufficiently to cover the expense of making the analysis. This limit is specific to each deposit and depends on geostatistical parameters, economic factors, and mining parameters. This study examines how the number of samples affects the recovered reserves and the resulting profit. Also, the effects on optimal profit of varying the different factors are examined. Globally, the number of samples required increases with the selectivity of the operation. For a given ore deposit, the greater the number of SMUs selected for processing, the fewer samples are required and vice-versa.

Jan 1, 1998

By J. M. Rios

Without conscious effort and understanding, a number of factors peculiar to mineral exploration campaigns conspire against building sustainability in host communities. These include the episodic and transitory presence of an exploration team in the community and the inherent uncertainty of outcomes; most projects fail. Given these circumstances, there is a strong tendency to apply a simple formula of providing employment, pragmatic philanthropy and supporting infrastructure improvements (roads, schools and clinics) to demonstrate that mining provides benefits. Experience in rural native communities of Mesoamerica has shown that it is possible to create positive, sustainable outcomes quite rapidly within communities, which build capacity, improve quality of life and support a strong social license to operate. Success comes from an understanding of community structure and dynamics; engaging with all segments of the community; creating healthy, transparent and accountable relationships based on clearly defined roles and responsibilities; and supporting and strengthening the role of women in a culturally appropriate way. To this are added innovative and culturally appropriate ways of incorporating sustainability through genuine social investment in areas more typically addressed by exploration companies; health, education, and environmental management.

Aug 1, 2013

By V. J. Southey

HOLLINGER mining operations have required development by 24 vertical shafts having a total length of 28,160 feet. Seventeen of these are sunk from surface and seven are interior shafts. Four surface shafts and three interior shafts are now active and, excepting the recently completed new main ore-hoisting shaft, the remainder are either abandoned, or are used for passes or for ventilation. The new shaft bottoms 60 feet below the 3,050 level, but there is much work to be done before it is placed in service. The term 'shaft practice' is intended to include shaft construction and a general treatment o typical equipment. It is a large subject for an organization the size of Hollinger and this paper is intended only to present the salient features. The writer wishes to thank the management for permission to publish this information and to acknowledge the advice and criticism o A. G. Irving, chief engineer, and the willing co-operation of other members of the Hollinger staff.

Jan 1, 1939

By B. Hewitt

Murrin Murrin Operations has not had a successful beginning. Numerous reliability and operability issues many of which are the result of design decisions have been addressed through mechanical and operational changes and the CCD circuit is no exception. The decision to install, the installation and the results of the CCD1 rake-lift mechanism and feedw ell dilution system are discussed in this paper. The installation was justified on improved operational robustness and an increase in the in the underflow density of 1% (per cent w/w). At approximately the same time process modifications in the solution neutralisation circuit were implemented and these changes altered the rheology of the slurry reporting to CCD1. Since the modifications to CCD1 and the solution neutralisation circuit, the CCD circuit has averaged a 2% improvement in the circuit underflow density. The CCD1 modification was completed on time and mechanically has performed well. From a risk point of view, the central rake-lift and Turbodil® dilution system add a degree of freedom and robustness to CCD1 operation that has extended the range of operational confidence. In this respect, the modification has been a success and is complementary to solution neutralisation improvements.

Jan 1, 2004

By G. A. Sutton

"At the San Manuel mine (Arizona, USA), in-situ copper leaching of a copper porphyry deposit was carried out from 1986 to 1999 during underground and open-pit mining. In 1993–1994, well¬field testing of the supergene zone, composed primarily of chrysocolla and copper-rich clay minerals, led to estimates that 52% of the acid-soluble copper (ASCu) could be recovered during in-situ leaching; however, the actual recovery from zone 6, which had the longest leach history, was approximately 42%. Comparing drillcore assay data from holes drilled before and after leaching also indicated an approximate recovery of 42%. The discrepancy between the predicted (52%) and actual (42%) recovery is probably related to several factors, including difficulty maintaining fluid saturation, channelling effects, and gypsum precipitation. ¦ KEYWORDS Copper oxides, in-situ leaching, Modelling, Porphyry, Solvent extraction and electrowinning (SXEW), Well-to-well RÉSUMÉ À la mine San Manuel (Arizona, États-Unis), on a procédé de 1986 à 1999 à la lixiviation in-situ de cuivre d’un gisement porphyre cuprifère pendant l’exploitation minière souterraine et à ciel ouvert. En 1993 et 1994, des essais effectués dans des champs de captage de la zone supergène, composée principalement de chrysocolle et de minéraux argileux cuprifères, ont abouti à des estimations selon lesquelles on peut récupérer 52 % de cuivre soluble dans l’acide (ASCu) pendant la lixiviation in-situ ; toutefois, la récupération réelle dans la zone 6, qui affiche l’histoire la plus ancienne en matière de lixiviation, était d’environ 42 %. La comparaison des données d’analyses de forage obtenues à partir de trous forés avant et après la lixiviation indiquait également une récupération approximative de 42 %. La différence entre la récupération prévue (52 %) et réelle (42 %) réside probablement dans plusieurs facteurs, notamment la difficulté à maintenir la saturation des fluides, les effets de canalisation et la précipitation du gypse. ¦ MOTS CLÉS d’un puits à l’autre, extraction par solvant et extraction électrolytique (SXEW), lixiviation in-situ, modélisation, oxydes de cuivre, porphyreINTRODUCTION in-situ copper leaching at the San Manuel mine, Arizona, USA (Figure 1), began in 1986. It was recognized that some of the copper oxide resource was not economically recoverable by conventional open-pit and heap leach methods using solvent extraction and electrowinning (SXEW) and a high stripping ratio would be required to access part of the resource. At the time, in-situ leaching was becoming popular in the uranium industry, but the approach was virtually unknown in the copper industry, especially at a large scale."

Jan 1, 2019

By J. M. Cummings

CONSIPERABLE information on the industrial or non-metallic mineral resources of British Columbia has been published. For a general resume of the subject, reference may be made to a paper presented by A. M. Richmond before the Annual General Meeting of the Institute in 1935 (1). To avoid duplication, the present paper is confined to a discussion of the existing industrial mineral industry of the Province and of the factors governing its present and future development. British Columbia's mineral production in 1936 had a value approximately 15 per cent of that for the whole of Canada. Preliminary estimates for 1937 indicate that this proportion has been maintained, although the totals have increased about 25 per cent. The following table presents comparative figures, for the year 1936, illustrating the relative importance of the major divisions of the mineral industry in British Columbia and in Canada as a whole.

Jan 1, 1938

By A. Ingelson

Conflict over mineral development and its impacts on indigenous peoples occurs in many countries around the world. Canada, Bolivia and Peru have experienced mine development for centuries in areas where indigenous communities have been and continue to be affected by the mining industry. On a global basis the mining industry continues to face the challenge of implementing meaningful consultation programs with indigenous peoples. Many governments around the world have adopted sustainable development as a policy and one important element of sustainable development is minimizing social conflict. John Moffet and Francois Bregha (Moffet & Bregha, 1996), in their analysis of the role of law reform in promoting sustainable development, noted that stakeholder participation can reduce this type of conflict. Social conflict can result in expensive litigation and costly project delays for mine developers. Meaningful consultation with indigenous peoples in areas where mine development is proposed can be a critical factor in securing a social licence to operate. A report released by the United Nations in 2005, outlined the elements of a concept called ?free, prior informed consent? (FPIC) that promotes more sustainable development. FPIC provides that mineral exploration and mining should not proceed unless the mining company has secured the consent of the relevant indigenous group(s). This paper employs a comparative approach to evaluate the extent to which three active mining nations, Canada, Bolivia and Peru, require consultation with indigenous residents and adhere to the principle of FPIC. The comparative approach assists in the identification of those consultation elements in the legal regimes of each country that can minimize social conflict in mineral exploration and mine development and therefore contribute to more sustainable development. First, we examine the legal requirements to consult with and accommodate indigenous communities in Canada, a country with a long history of mineral development over a large geographic area that has entrenched in its Constitution the protection of indigenous peoples? rights. We then turn to an analysis of Bolivia, one of the most indigenously conscious mining jurisdictions that has followed the Canadian lead in entrenching constitutional protection for indigenous peoples. Third, the approach to consultation with indigenous peoples in Peru, a nation that has not adopted the Canadian and Bolivian approaches to constitutional protection of indigenous peoples rights, is considered.

Aug 1, 2013

By George E. Cole

Introduction In view of the fact that, during the past year, two Manitoba mines-Flin Fion and Sherritt Gordon-have entered the list of producers and have materially increased that Province's contribution to the metal production of the Dominion, it would seem appropriate at this time to review the progress of the industry in the Province, with particular reference to the out-standing metal-mining developments of the past decade. That these two mines have been able to continue their operations in spite of the low prices of copper and zinc adds a touch of brightness to the industrial life of the Province. Depression in metal prices is not encouraging to the mining industry, but it does stimulate efficiency in methods and costs of production. As two thriving towns have grown around the two mines, the will of the management to carry-on is of great consequence to Manitoba, this year so hard hit by the .agricultural depression. And, much as it is a pleasant feature in the mining situation that these mines have been able to continue operations, nevertheless it must be noted, in reviewing the mining developments of the past few years in Manitoba, that the Province was fortunate enough to profit by good times, in that an industry was established which gives evidence of permanency. In the metallic field, the section of Manitoba that first received attention from prospectors was the boundary district, west of the Lake of the Woods. Several claims were staked here at the time of the gold boom in the neighbouring Ontario area. But the first real interest in metalliferous deposits dates from the discovery of gold in March, 1911, in quartz veins on the shores of Rice lake, some twenty miles east of lake Winnipeg. Systematic and organized prospecting of the pre-Cambrian areas of the Province may be said to have commenced with that discovery. The first gold discovery in northern Manitoba was made at Wekusko (Herb) lake in 1914. This was followed by the discovery of the Flin Flan and Mandy copper ore-bodies in 1915 on Flin Fion and Schist lakes, respectively.

Jan 1, 1932