Search Documents

By Erik C. Westman

Knowledge of the orientation and relative magnitude of in-situ stresses at the mine scale is important for safe and efficient production from an underground mine. With this knowledge, stope location and scheduling can be optimized. Passive seismic tomography was used for imaging horizontal stress distribution at the mine scale. Microseismic measurements from the Creighton mine were used as input for the tomography calculations. The double-difference tomography algorithm was used, which provides the most precise results. The results clearly show a low velocity zone in the previously mined areas bounded by two high-velocity lobes located adjacent to the mined openings at locations consistent with those expected due to the horizontal stresses at the mine. The overarching goal of the research is to provide a tool that can augment both numerical modeling results and underground geotechnical measurements to allow the mine operator to produce in the safest and most efficient manner possible.

Jun 1, 2012

By V. S. Sastri, Elboujdaini. M.

"Economics of wear in mining industry and methods by which wear cost may be reduced will be discussed.IntroductionCanada loses more than $5 billion annually due to friction and wear (Table 1). It is estimated that about $1.3 billion, or about 25% of the losses, could be saved through better application of existing technology (Table 2). It should be noted that the costs given in Table 1 and 2 refer to 1986. The losses due to friction and wear and the savings would be much higher in 1996. Tribology combines the many branches and specialties in science and technology concerned with understanding and combatting friction and wear. Specifically, tribology is concerned with the design and manufacture of sliding and rolling bearings, piston rings, gears, cutting tools and other devices in which surfaces interact, in sliding or other relative motion. Tribology is concerned with the correct use of materials for interacting solid surfaces, with the interaction of the surfaces with the lubricants, with the chemistry, physics and use of lubricants. It is concerned with the reduction of friction and wear and the avoidance of associated failures in machinery. Similar tribological components such as bearings are used in different technologies and similar tribological problems such as abrasive wear occur in different industries. Thus, tribology is in itself a generic science and technology, concerned with the generation and dissemination of knowledge on friction, wear and lubrication, and the application of the knowledge, to a wide range of industrial products and equipment, from ploughs to space equipment, from prosthesis to engines, from washing machines to railways, from computers to power stations, from paper mills to mines. Avoidable losses due to friction and"

Jan 1, 1997

The introduction consists of back-ground information, of an historical and statistical nature, relating to the Thompson mine. The geological presentation is based on illustrations that are intended to provide a progressively closer look at the ore occurrence. The illustrations consist of an index map, a geological map of a 15-by 85-mile area including the Thompson mine, a series of four maps dealing with the geophysics and geology of a 6-by 4\f.j-mile area at Thompson, a mine level plan and corresponding section, two sto11e 11lans and corresponding sections, and photo-graphs and photomicrogra11hs of the various one types. T HE Thompson mine is located about 400 miles due north of Winnipeg. The ore deposit was dis-covered in February, 1956. Five years later on March 25, 1961, the Thompson production facilities were officially dedicated with the shearing of the first nickel produced at the Thompson refinery. Full production, at an annual rate of more than 75,000,000 lbs. of refined nickel, was attained later in the year.

Jan 1, 1963

By Robert D. McKellar, Luke Frawley, Richard Okrasa

"The resource industries in Canada are facing increasing global competition and stringent environmental regulations. This has made it essential for companies to lower operating costs wherever possible. Electrical energy rep-resents one variable cost that may be better managed and utilized, providing the user with lower operating costs, improved productivity and better yields.The utility industry is also facing changes in the way it must do business. Utilities in North America are facing the prospect of deregulation that will eliminate the monopoly they have traditionally held. This will force them to strive for lower operating costs, to maintain a competitive position and to improve customer ser-vice so as to maintain their customer base.Ontario Hydro has been working with industry for several years. Many opportunities for cost savings have been identified involving energy efficiency, process improvements and the use of new electro technologies. One useful service that the utility can offer industry is to increase the awareness of potential opportunities suited to their operations. This paper will provide an overview of some of the projects that have been implemented and those that are presently being evaluated. An electronic data-base of electro technology applications that is under development will also be described."

Jan 1, 1996

By Cheowchan Leelasukseree

Mae Moh mine, operated by Electricity Generation Authority of Thailand (EGAT), is the largest open pit mine in Southeast Asia. Its production is approximately 15 million lignite tons and 90 million m3 of waste, annually. The bottom of the final pit limit is designed to be approximately 500 m in depth. Presently, the pit depth is almost 250 m below original surface. The complexity of geological structures, such as faults, has caused a number of geotechnical difficulties. In a challenging lowwall area, called Area 4.1, an inclined weak bedding plane, G1, will be daylighted along the lowwall as following by mine plans. The dimensions of Area 4.1 are nearly 300 m wide and 90 m high. The friction and dip angles of the G1 interface are reportedly 12° and 15°, respectively. A three million m3 claystone block, resting above G1, would potentially slide down, and possibly cause a massive failure. EGAT engineers are acutely aware of the potential gigantic sliding failure and are modifying the mine plan in Area 4.1 to improve mine safety and minimize the displacement of the potential sliding block, reduce the possibility of failure and lower the additional mining cost as much as possible. The cut and fill mining technique was selected and studied to achieve those goals for mining in Area 4.1. With this mining technique, G1 will be partially daylighted. Therefore, an arch formation is induced with a sliding block above the mining area, which could perform as a temporary support undercutting a certain span. Initial studies of the behavior of the partially undercut slope are presented in this paper, along with a review of the similar failure history in Mae Moh mine and a 3-dimensional numerical model of the mine. The failure history review provides an estimation of undercut span without failure. The three-dimensional numerical model results, using 3DEC, gave an initial approximation of the displacement of the sliding block in Area 4.1. The next exciting study of the behavior of partially undercut slope is a trial undercut slope field experiment in Area 4.1. Currently, a trial undercut slope field experiment in Area 4.1 is under construction. In the field experiment, a number of monitoring programs will be installed in Area 4.1 to monitor and obtain information to allow a better understanding of the behavior.

Jun 1, 2012

By T. L. Tanton

Introduction Sturgeon River area, on the east side of lake Nipigon, Ontario, was the scene of a gold rush in 1934. According to press reports, the active staking during the latter part of the summer spread out rapidly from the early holdings until it embraced practically all of the lower basin of Sturgeon river in a belt up to ten miles wide extending west from Kinghorn for 35 miles to lake Nipigon. And, before winter set in, active prospecting and claim staking reached beyond lake Nipigon to areas where belts of ancient schists were known, notably west of Obonga lake. The writer's familiarity in past years with the areas to which attention has been directed admits of some observations on means of access in the field, the general geology, and the progress that has been made in identifying formations favourable for the occurrence of gold. Canoe Routes From the writer's observations in Sturgeon River area in 1917 and in the Obonga Lake area in 1933, it is recalled that there is, locally, a striking dif~ ference in the accessibility of the two areas by travel along canoe routes. Sturgeon River area is easily accessible from Kinghorn or Jellicoe stations on the Canadian National railways. Many small lakes, commonly of the linear type and with elongations east and west, occur among the forested rocky ridges near Jellicoe (Figure 1) and to the east and west along, or adjacent to, Sturgeon river. This stream has long stretches with gentle current between the falls and rapids. The drainage system provides excellent canoe routes (Figure 2), and the interruptions to travel (Figure 3) are remembered .as scenic features that were passed by portages with firm footing. West of Obonga lake, the streams flowing easterly to lake Nipigon may be followed through scenic canyons to a plateau of law relief characterized by extensive muskegs and shallow, brown-water lakes; and along small streams, where beaver dams have been destroyed, there are muck ponds where the usual alternatives of paddling or portaging can be dismissed in favour of the 'moosing' method of progress with the canoe (Figure 4).

Jan 1, 1935

By E. Swartzman

"DURING 1951, experimental cleaning studies on both fines and larger sizes of certain Canadian coals were conducted on a relatively large scale in two pilot plants in the United States, large enough to be considered as small commercial units, and in one commercial plant in Canada.One of the pilot plants was a wet washer of a type which apparently has never been .used in Canada, nor has any Canadian coal been tested in it before. In the other pilot plant and in the commercial plant, dry cleaning equipment was used. The commercial plant is the first of its kind to be employed in Canada, and this type is used only to a limited extent in the United States.Fine-Coal Cleaning ExperimentsTest PlantsHydrotator and Hydrotator-Classifier combination pilot-plant with a capacity of about twenty tons per hour. This is a classifier type washer adapted for cleaning fine coal as well as certain intermediate sizes. The Hydrotator deals with that portion of a coal retained on approximately a 24-mesh Tyler sieve, whereas the Hydrotator-Classifier deals with the minus 24-mesh fines."

Jan 1, 1952

By H. F. Naldrett

"AbstractAt the end of May, 1950, Imperial Oil, Limited, had completed a total of 192 D-3 wells in the Leduc-Woodbend field, 62 of which lost circulation in the D-3 zone for periods ranging from two hours to fifty days. The majority of the remaining wells •lost some mud without actual loss of returns. In addition, independent operators completed 69 D-3 wells, of which 9 lost circulation. Included among the latter is the now well known Atlantic No. 3 well, which blew wild out of control for seven months. The well was finally brought under control through two directionally drilled wells, but not before the derrick fell and the well caught fire. Practically all known filler materials have been used in attempt3 to prevent or regain loss of circulation, but none has been successful, except in minor cases. Ordinary sawdust has come to be the most commonly used filler material and is added to the mud before the D-3 zone is contacted. In cases of serious loss of circulation, the on1y successful method of getting returns has been the use of a series of small cement plugs.IntroductionThe Leduc field is twenty miles southwest of Edmonton, Alberta. Geologically, it is on the east limb of the Alberta syncline, in the homoclinal belt. The main productive zones are in the Upper Devonian formation and are known locally as the D-2 zone and D-3 zone, respectively (see Figure 1).The D-3 zone is a dolomitized reef with fair average porosity and permeability, and shows considerable evidence of vertical fracturing. Porosity is mainly due to moderately uniform development of vugs which are interconnected by small crevices. However, the formation is known to be, locally, extremely vuggy and in places cavernous. These latter conditions create very serious drilling problems due to the hazard of loss of circulation, particularly in the gas cap, which has a maximum thickness of 200 feet. The D-3 zone is contacted at an average depth of 5,300 feet."

Jan 1, 1950

By H. G. Harper, R. C. Hart

"The Mississagi quartzite is the basal formation of the Quirke Lake trough. As it is traced around the rim, a gradual change in dip is observed, as follows:Northwest corner 50 degrees south.Algom Quirke mine 34 degrees south.Quirke Lake 25 degrees south.Whiskey Lake 22 degrees west.Pecors Lake 25 degrees north.Algom Nordic mine 18 degrees north.Elliot Lake 11 degrees north.Pistol Lake 5-7 degrees west.Thus the apparent synclinal axis is a curving east-west line lying closer to the north limb than to the south. The axis appears to plunge west at about 5 degrees.The Huronian sediments lie on a basement of granites, gabbros, and volcanics. Diamond drill evidence indicates that this basement has a surface of peneplanation, and that the areas of soft basic rock have a smoother topography than the granite. For the most part the orebodies at the Quirke and Nordic mines overlie a basement of soft basic rock.The Mississagi formation is the host rock of the deposits, and its primary structures are suggestive of the conditions under which the conglomerate beds were deposited. Cross-bedding is common, although normal bedding varies from thick to thin to essentially lacking. Grain gradation is not common. Where coarse and fine grains occur together, the coarse tend to be more rounded than the fine. These features are characteristic of shallow-water deposits, laid down above the lower limit of wave action. Therefore, the quartz-pebble conglomerates probably represent ancient water courses, bays, beaches, and bars.The causes governing the creation of the trough can only be conjectured, but there is evidence that both subsidence and compressive stresses played active roles. Drag-folds in argillite beds near Whiskey Lake indicate compressive stress. On the other hand, gentle crumpling in thin-bedded limestones on Quirke Lake is probably due to pre-induration slumping and folding. If strong compression had been widespread within the trough, one would expect drag-folding and shearing of the incompetent beds to be more general. Two large-scale, fold-like structures were mapped by Collins, but their axes do not parallel the trough axis, and they are therefore not related to the major structure."

Jan 1, 1949

By E. J. Burrough

Coal Reserves The Crowsnest Pass coal fields form part of a greater area which comprises the Inner Foothills belt of the Alberta coal fields and the southeastern coal fields of British Columbia. The most valuable and most extensive reserves of the bituminous coals of Canada are concentrated in this?area, of which the Crowsnest Pass fields form an important part. The extent of these coal reserves together with those of the rest of Canada were recently studied by the Geological Survey of Canada for the Royal Commission on Coal of 1946 (1). Quotin from the report, it is of interest to note that, prior to this work, the most widely known, and in fact the only Canadian-wide estimates of, coal reserves of Canada available to the Commission were those prepared by Dr. Dowling in 1913 (2). At that time it was estimated that Canada's reserves of coal were over twelve hundred billion tons. The more recent estimates of mineable coal for the whole of Canada are of the order of 10 per cent of that figure and are reported. as 99 billion tons, which is further reduced to 40 billion tons on the basis of the estimation of recoverable coal. This considerable divergence in estimated reserves is explained in part by the big difference in the bases of measurements. For example, in the original report, seams of one foot occurring at a depth of 4,000 feet were included in the estimates.

Jan 1, 1951

By F. Daniel Rosenkranz, Peter L. Silveston

Experiments investigating the treatment of a ground wood white water waste from an Ontario pulp and paper mill by an HVCB coal are reported. Adsorption capacity for the waste, with a soluble COD contribution of 2,100 mg/I, amounted to 0.17 per cent, by weight, of the Nova Scotia coal used. Percolation of the white water waste through a coal bed indicated that soluble COD is removed. For finely ground coals, over 90 per cent of the suspended solids in the waste are retained on the coal. Plugging of the coal bed is rapid, so that any treating process using filtration would have to renew the surface of the bed frequently.

Jan 1, 1970

By J. O'Leary, R. Cannell, D. Honsberger

"The Scully Mine deposit lies within the group of metasediments that together comprise the rocks of the Labrador Trough. The ore itself still retains the bedding characteristics of the parent rocks and on this basis has been divided into three main members, namely: Upper, Middle and Lower. The Upper and Lower both show many of the bedding characteristics of the cherty taconites of the northern U.S.A.; the Middle member is a coarse-grained friable specularite rock. The ore minerals are hematite (normally present in the specular variety) and magnetite, although the latter rarely occurs in concentrations greater than 20 per cent. Gangue minerals are quartz and the hydrated iron oxides. Manganese oxides also occur as accessory minerals. The outcrop area of the orebody is in excess of 2 square miles, displaying a complex pattern of faulting and folding, which has been formed as a result of at least two orogenic periods."

Jan 1, 1972

By Boyd Davis, Brook Zaback

"Among the first published papers from Prof. Torstein Utigard was work on imaging the aluminum electrolysis process and in-situ measurements of aluminum in cryolite melts. He and Prof. Jim Toguri used an x-ray radiographic technique to measure interfacial tension of aluminum drops. Publications using this equipment for aluminum electrolysis spanned from 1985 to 2006. As well, other methods were used to better understand electrolysis in molten salts, including hot-stage microscopy, direct observations from above the bath and water modeling techniques. For chloride systems (for magnesium and lithium), it is possible to see side-on the electrolysis using a quartz cell. In honour of Prof. Utigard’s contribution to this field, this paper presents a summary of work on visualization of molten salt electrolysis, including work done at the authors’ labs and others around the world. The paper will summarize key findings and their possible impact on molten salt electrolysis."

Jan 1, 2015

By D. G. Cerigo, D. M. Bryce, P. H. Jennings

This paper summarizes the results of an experimental and economic study undertaken to evaluate the feasibility of treating an oxidized orebody of about 10 million tons, grading about 0.75 per cent copper, by agitation leaching and by percolation leaching.

Jan 1, 1968

By T. Bednarski, T. McCallum, L. Moya, L. Nsenga, B. Mbao

The accumulation of solids in solvent extraction (SX) circuits can cause problems with the physical and economic performance of the operation. These solids are responsible for the formation of crud, a solid stabilized emulsion containing organic, aqueous, air, and fine solid particles. The build-up of crud in SX settlers can limit SX operation throughput, require plant downtime, lead to higher organic losses, or result in higher aqueous in organic entrainment (all of which can have a significant, negative economic impact). Current practices for crud management are typically reactive. Crud is physically removed after it has been allowed to build to excessive levels in the circuit and processed mechanically using centrifuges or filtration. A new proactive solution has been developed to prevent crud formation and build-up. Low ppm dosage of an additive, ACORGA® CR60, into the pregnant leach solution (PLS) has resulted in reduced crud formation in pilot and commercial scale for a variety of PLS streams. This paper will review results from operations in North America and Africa, covering heap leach, concentrate leach, and agitated leach feeds. INTRODUCTION Crud formation and build-up in solvent extraction (SX) circuits has been a long time topic discussed and claimed to be crucial to the whole hydrometallurgical process (Liu, et al, 2006). Crud formation is present in all SX systems be it copper, uranium, zinc, etc., and Ritcey (1980) defined crud as a stabilized emulsion containing organic, aqueous, and fine solid particles. The ore type and feed composition is a major determining factor of crud formation and typically contains Si, Al, Fe, P, and sulfates (Ritcey, 1980). It typically builds at the interface between the organic and aqueous, but can also be observed as floating crud on the surface of the settler, or bottom crud, which is common to find in circuits treating agitated leach feeds such as in Africa. As crud formation has been unavoidable, many of the current crud management techniques are reactive, allowing crud to form and build in SX circuits. Once it does, it is removed and treated via different mechanical techniques, typically through some type of filtration or three-phase centrifuge, to remove the solids and recover the organic phase trapped within the emulsion (Ritcey, 1980). Automated pumping systems have also been designed and are frequently used in North American operations. The time and capital required to react to crud formation can be an overwhelming aspect to SX operation.

Jan 1, 2019

By L. López

Argentina reported about 40,000 tonnes of uranium (tU) as reasonably assured resources and inferred resources for the production cost category <130 US$/kgU in the OECD-NEA/IAEA classification scheme. These resources belong to the following projects: Sierra Pintada, Cerro Solo, Don Otto, Laguna Colorada, Laguna Salada, Meseta Central and Amarillo Grande. With three heavy water reactors in operation and an approximate installed capacity of 1.7 GWe, the current natural uranium requirements are about 220–250 tU per year. Based on various nuclear growth scenarios, it is estimated that by 2030 there will be a generation capacity of some 3,092 GWe for the reference case, with raw material needs of some 486 tU per year. Currently, there are no perspectives for local uranium production in the short term, and it is thought that uranium projects with identified resources must complete resource delineation and advance in technical pre-feasibility studies for the recovery of uranium. It is expected that Argentina continue meeting the uranium demand with imports in the next following years. In the Latin America region, both Brazil and Paraguay could be considered as potential uranium suppliers. In conclusion, despite the apparent growth prospects for the use of nuclear energy to generate electricity in Argentina, there are no immediate prospects for the provision of uranium oxide concentrates from domestic deposits for fuel fabrication. This has implications for supply and energy security.

Jan 1, 2020

By R. Bruce Graham

The formation, evolution and classification of peat bogs is discussed. Factors resulting in the internal and external morphological changes in a bog are described. The fibrous, absorptive and sterile properties of peat moss account for its widespread use in horticulture and related fields. These properties also account for its usefulness as a binder in pelletizing, as an insulating material in bat tons and in panel construction. Peat, the humijied product of peat moss is used in market gardening and sod growing. It is utilized in Europe as fuel. It is a source of activated carbon and gas. Potentially peat can be used to produce waxes, resins, tannins, cellulose, hemicellu/ ose, humic acids, lignin and hymatomelanic acid. At present other cheaper sources are available.

Jan 1, 1984

By J. B. McKenzie

Since connnencing underground prcxiuction in 1979, the Ruttan Mine has been prone to secon:iacy sulphide dust explosions. Al though infrequent during the early years of prcxiuction, these occurrences did result in major damage and lost time injuries. 'As the mine exparrled and developed to further depths, sulphide dust explosions occurred on a more frequent basis. Incomplete ventilation se:rvices, required to exhaust the affected areas, caused frequent delays resulting in lower prcxiuction rates due to the time required to ventilate the affected areas of the mine. CUrrent procedures to minimize the effects of secon:iacy dust explosions evolved from practical suggestions arrl examining methcx:ls other mines have developed to cope with the problem. Procedures and regulations to protect errployees from exposure to hazards of sulphur dioxide are time consuming, expensive and counter prcxiuctive in their present fonn. This paper describes the history of secon:iacy sulphide dust explosions at the Ruttan Mine and the methcx:ls and proced.ures currently in place to minimize and contain the effects of dust explosions.

May 11, 1988

By R. Harrisson, K. Esmaieli

Brunswick mine employs an ore and waste pass system for material transfer. This paper reviews the evolution and performance of ore pass systems at the mine. It presents the range of selected configurations, inclination, dimensions, etc. Select case studies are used to address the influence of structure, stress and materials handling on the longevity of the employed ore passes.

Jan 1, 2008

By Ron Zevenhoven

In Finland one opportunity for large-scale CO2 capture, utilisation and storage (CCUS) is CO2 mineralisation, i.e. mineral carbonation. A process route under development towards industrial application involves production of magnesium hydroxide or sulphate from serpentinite rock (serpentine = 3MgO·2SiO2·2H2O), followed by conversion either in a pressurised fluidised bed (PFB) reactor, giving magnesium carbonate, or in an aqueous solution process giving magnesium hydro-magnesites. Iron present in the rock is typically obtained FeO(OH). Results obtained with these process routes and progress towards industrial demonstration is addressed, process heat integration and operation on flue gases (without CO2 pre-separation!) being key features for economic viability. A process route utilizing calcium-containing slag by-product from iron- and steelmaking under development towards large-scale application is the so-called slag2pcc concept. It converts an industrial by-product into valuable material, reduces use of natural material and streams to landfills while binding CO2 produced by the process generating the slag. Using ammonium salts, calcium is extracted from steel converter (BOF) slags and subsequently carbonated in a two-stage aqueous process (at ambient temperatures and pressures). Precipitated calcium carbonate (PCC) is produced while regenerating the ammonium salt. Process performance and scale-up while guaranteeing a certain PCC quality are presented.

Jan 1, 2015