Search Documents

By Ron Zevenhoven

In Finland one opportunity for large-scale CO2 capture, utilisation and storage (CCUS) is CO2 mineralisation, i.e. mineral carbonation. A process route under development towards industrial application involves production of magnesium hydroxide or sulphate from serpentinite rock (serpentine = 3MgO·2SiO2·2H2O), followed by conversion either in a pressurised fluidised bed (PFB) reactor, giving magnesium carbonate, or in an aqueous solution process giving magnesium hydro-magnesites. Iron present in the rock is typically obtained FeO(OH). Results obtained with these process routes and progress towards industrial demonstration is addressed, process heat integration and operation on flue gases (without CO2 pre-separation!) being key features for economic viability. A process route utilizing calcium-containing slag by-product from iron- and steelmaking under development towards large-scale application is the so-called slag2pcc concept. It converts an industrial by-product into valuable material, reduces use of natural material and streams to landfills while binding CO2 produced by the process generating the slag. Using ammonium salts, calcium is extracted from steel converter (BOF) slags and subsequently carbonated in a two-stage aqueous process (at ambient temperatures and pressures). Precipitated calcium carbonate (PCC) is produced while regenerating the ammonium salt. Process performance and scale-up while guaranteeing a certain PCC quality are presented.

Jan 1, 2015

By J. Marks

The measurement of greenhouse gas (GHG) emissions from primary aluminium production and inventory of these emissions of carbon dioxide and PF Cs have become an important issue for primary aluminium producers. Most global producers have either voluntary emission goals or emissions limits established through national regulatory requirements. International good practices for inventory of these emissions for national governments are established through the Intergovernmental Panel on Climate Change (IPCC). The current good practices, last updated in 2000, are being revised and are expected to be adopted by governments in the spring of 2006. There are a number of changes expected in the guidance that will impact how facilities account for their GHG emissions. This paper describes the changes to the guidance and the implications of these changes for aluminium producers.

Jan 1, 2006

By C. Doyle, D. M. Hoffman, C. Díaz, J. Hrepic, W. J. Koshut, R. H. Hanewald

"Recently, lining life of the INMETCO submerged arc furnace has been dramatically extended from an average of eleven months in the 1980s to a current record of 34 months. This paper summarizes test work and operating results describing the development and establishment of slag parameters that reduce corrosion of the magnesite-chrome refractory lining.The desired slag parameters are now maintained by utilizing waste streams as slag additives. This paper also discusses the successful evaluation of a rebonded-fused-grain magnesite- chrome refractory as a lower cost, more thermo-mechanically forgiving alternative to a fused-cast magnesite-chrome refractory that had been the refractory of choice in previous years at INMETCO.IntroductionSince 1978, INMETCO, a wholly owned subsidiary of INCO Limited, has been well known for recycling by-products from the production of stainless steel, namely, EAF bag- house dust, mill scale and grinding swarf. INMETCO operates the only smelter in North America dedicated to the recovery of nickel, chromium, and iron from hazardous and nonhazardous waste. The process was developed in the research laboratories of INCO. In recent years, the process has been successfully modified to accept a wider variety of other specialty steel waste streams including: spent pickling solutions, pickling and waste water treatment filter cakes, acid scale, carbon brick, spent bag-house bags, torch cutter dust, spent dolomitic and chromium-bearing refractories, and rechargeable nickel-cadmium batteries."

Jan 1, 1997

By E A. Mitchell

In the fall of 1961, Cominco dis-carded its long-established system of feeding the lead blast furnaces by narrow-gauge tram and V-cars, and installed an elevated monorail bucket system. This system automatically loads buckets of sinter, along with the correct proportion of coke, and delivers them to any of several designated furnaces. Direct labour usage has been reduced by nine men per day; improved coke proportioning has been achieved; and a major safety hazard has been eliminated. Introduction I N THE fall months of l 961. the system of feeding the lead blast furnaces at the Trail, B.C., smelter of The Consolidated Mining and Smelting Company of Canada Limited was altered from the tradition-al narrow-gauge railway and V-car method to one employing mono-rail carriers. The change was in keeping with a recent trend at Trail to replace narrow-gauge tramming with alternative methods of materials handling. In the case of the blast furnace feeding, the

Jan 1, 1963

By L. D. Roper

"This paper introduces novel comminution flowsheet concepts involving a novel apparatus, eccentric-high-pressure-centrifugal-comminution (eHPCC), and forthcoming advantages to the international mineral processing community. eHPCC is one-machine synergising high-pressure-rolling surfaces, high-intensity-attrition and centrifugal classification. eHPCC has demonstrated: an absorbed power- intensity of 4 MW/m3; receipt of lump feed whilst producing 80% of product particles less than (p80) 120 µm (choke-fed, dry, open circuit without grinding media; an inert comminution environment); tramp metal tolerance, and a minimum embodied-free-energy saving of 15% as compared against conventional comminution (this comparison withstanding 133-times difference in throughput). Furthermore, this paper introduces: process design and operating characteristics of eHPCC (wet, dry, with and without grinding media); reline considerations (vertical-lift without confined-space). The international mineral processing community is invited to consider eHPCC as an alternative to conventional comminution circuits and/ or complimentary so as to enhance existing process flow sheets.INTRODUCTIONEccentric-high-pressure-centrifugal-comminution (eHPCC) was conceived in 2013 (Patents pending) and has the potential to eliminate the in-efficiencies and complexity of conventional tumbling mill circuits. During the development and testing phase eHPCC demonstrated improved energy efficiency and sustainability offsets.eHPCC will compliment any upstream feed source, be it run-of-mine (ROM), primary crushed rock, or any other conventional comminution stream such as tumbling mill oversize. Another novelemerging technology, Conjugate Anvil-Hammer Mill (CAHM) (Nordell and Potapov, 2011), receiving ROM, will be a complimentary open-circuit feed to eHPCC for very high throughput flow-sheets.eHPCC may compliment downstream process requirements through selective mineral liberation. Selective mineral liberation is entirely feasible as the ore is comminuted upon itself (autogenously) in the high pressure zone caused by the synchronous rotating components."

Jan 1, 2016

By J. Ga?parík

The optimal selection of machine or machine group for building processes is very important role of building planner during the process of building planning. During this process building planner have to analyze several factors influencing the final effective decision concerning this problem. There are several factors and criteria for effective selection of building machines. In our contribution there are analyzed: ability of machines to realize designed building process (quality aspect), duration of mechanized process (time aspect) and minimizing of energy consumption (cost and environmental aspect). Selected scientific methods and theories of problem solution can be divided into these groups: theory of system (creation of building machine selection method), multi-criteria optimizing method (analysis of mechanized building process from the point of more optimal criteria), queuing theory (application during the mathematical modeling of mechanized soil processes), method of scientific analysis (analysis of factors influencing final decisions), method of scientific synthesis (creation of optimizing method implemented into building processes and possible application in construction sector). Multi-criteria optimizing method were during our research work implemented into soil processes and selected building group machines (excavators and trucks), which are very often used in construction and mining processes. This method can be considered as a multi-level decision making process based on multiple parameters. In our contribution is presented key mathematical models for model example solution and software built in Java, which has been created as a support for method described in this contribution. Application of this method and software will increase the effectiveness of building machine selection from the point of key criteria of optimizing: quality, time and energy consumption.

Aug 1, 2013

By D. Janney

Kennecott's Utah Smelter commenced operations in June 1995 utilizing Outokumpu Flash Smelting (FSF) and Kennecott-Outokumpu Flash Converting (FCF) technology. After some initial teething and equipment problems the smelter achieved its design capacity in mid-1997 and now processes over 1.0 million tonnes of copper concentrate per year with exceptional environmental performance. The smelting furnace has operated for 11 years and the converting furnace for 5 years without major shutdowns. The first major smelter shutdown commenced in September 2006 after extensive planning. The FSF was completely re-bricked and the latest above and below bath containment systems installed. The FCF was inspected and re-bricked with some improvements made to the above bath containment system. The FCF life is now anticipated to be the same as the FSF. Numerous improvements and modifications were made to the rest of smelter facility including extensive upgrades to the dry electrostatic precipitators. Production ramp-up was smooth with the smelter now frequently operating at acid plant capacity.

Jan 1, 2007

By Michael W. Hinds

X-ray Fluorescence Spectrometry (XRF) is used at various stages of gold refining. Initially, incoming impure gold is analysed for deleterious elements such as As, Cd, Hg, Se, and Te. Based on the levels of these impurities the material can be returned to the client or accepted for refining. XRF is also used to determine the metal concentrations after the impure gold has been melted and sampled. This information is used to assist the final Fire Assay determination of gold and silver. An energy dispersive XRF is used to determine the end point of chlorination refining step.

Jan 1, 2011

By G. Riveros

A new, continuous fire refining process for copper has been developed and tested at the 5 tph pilot scale. During oxidation, the blister copper flows through a packed bed of crushed refractory bricks counter-current to a hot oxygen containing gas. The resulting desulphurized copper flows then directly into a packed bed of charcoal for deoxidation. By controlling the air to natural gas ratio, both temperature and reducing conditions can be controlled. Based on extensive laboratory scale measurements of the rate of copper oxidation and reduction, the process concept was developed aided by process modeling and simulation. The industrial-pilot scale installation built at the ENAMI Paipote smelter in Chile, consists of two cylindrical, compact reactors, operating in line, with a designed capacity of 5 t/h of blister copper. The results of the industrial-pilot tests confirmed the feasibility of the new process. The blister copper processing capacity was increased to 10 t/h with satisfactory sulphur removal. The degree of oxidation as well the copper temperature was controlled with relative ease. The specially designed siphon block allowed for smooth tapping of the oxidized copper and separation of refining slag. The reduction of oxidized copper in the packed bed of charcoal appeared to be very effective while control of the degree of reduction according to the height of the bed ensured control of the oxygen content in the refined copper at the required level.

Jan 1, 2007

By Ralph L. Rutherford

Introduction During the past twenty-five years we have seen considerable exploration for oil on the plains of southern and east-central Alberta. This exploration has to some extent gone on in cycles, with periodic starts, stops, and occasionally some reversals. Each major attempt is usually supplemented by the application of some new method of exploration and, following each period of exploration, drilling tests are made. Whereas oil-bearing horizons are the ultimate objective of these explorations, the preliminary investigation frequently aims at a discovery of structure based on the long accepted belief that accumulations of oil and gas are to a marked degree structurally controlled. At the inception of this general exploration for oil, it was natural that attention should be directed to areas where there was surface evidence of deformation of the underlying strata, but, as the programme progressed, it was found that these surface manifestations of structure were often deceptive when attempts were made to project them to depth, to involve the deeper strata. Drilling of test wells was the only satisfactory method of obtaining exact information.

Jan 1, 1946

By A. N. Shen

Fe3A1 intermetallics are potential inexpensive candidate for hot applications. In this project, torsion tests on hot-rolled and annealed Fe3A1 (Fe-15.5A1-5.8Cr-1.0Nb¬0.05C) were carried out over the ranges 750-950°C and 0.01~1s-1 . The experimental results showed that when peak stress op>90MPa (LogZ>16s-1 , Z: temperature-compensated strain rate), specimens cracked at randomly low strains. Optical microscopy exhibited original elongated grains and many grain boundary cracks associated with segregation. With op<40MPa (LogZ<16s-&apos;), specimens deformed with low random op but considerably high fracture strains; slowly propagating cracks may explain the reduced flow stress. Optical microscopy showed both elongated grains and equiaxed subgrains with some indications of geometric dynamic recrystallization (gDRX) and of static recrystallization (SRX). Compression tests gave higher stress with little effect of the preexisting cracks. The activation energy Quw of current material in satisfactory torsion and compression tests is about 10% higher than previously published. Fe3A1 has body-centered cubic structure in the experimental range, so it was compared with ferritic stainless steel 434C (Fe- 16.55Cr-0.96Mo-0.21Ni). Constitutive constants and restoration mechanism are compared between these materials. While Fe3A1 is hardly a light metal, it is considerably lighter than most steels. Furthermore, like the other body centered cubic metals (BCC) (a-Fe, ß-Ti, ß-Zr and ß-brass), it exhibits a high degree of dynamic recovery (DRV) like Al alloys, producing easier hot workability than that of austentic stainless steels.

Jan 1, 2007

By P. Momni, D. Ersenkal

Equator Principles (EPs) are a set of guidelines developed and adopted by a series of financial institutions for assessing and managing social and environmental issues in project financing. Established in 2003, EPs are now adopted by some 68 financial institutions from 27 countries. As more and more financial institutions join this global initiative, it is important for project owners to have a logical framework embedded into the project lifecycle to reduce the risk of non-compliance which could result in costly delays. This paper outlines a proactive approach for project developers in order to integrate environmental and social aspects into entire project lifecycle.

Jan 1, 2010

By B. Tougas

Recycling of titanium represents an important economic activity due to high cost of the material and the amount of returns of machined parts which represent the bulk of finished titanium products (typical "buy to fly" of 10 in the aeronautic industry). In the present work, the metallurgical quality of 76 mm in diameter and 20 cm ingots poured in coated graphite mold will be assessed against the nature and condition of application of 4 coatings namely aluminum oxide, yttrium oxide, zirconium oxide and zirconium oxide with 4% aluminum oxide. The metallurgical quality has been evaluated in terms of alpha case thickness, microstructure and composition. Microhardness from surface will be assessed against casting conditions. Least square regression analysis have been use to optimize casting conditions.

Jan 1, 2011

By P. M. Pearson

This paper describes the principles ()f systems engineering and their application to the various transport problems confronting the mining industry. The organization of mining operations into sub-system design problems is explained.

Jan 1, 1970

By Richard Simon

This paper presents an ongoing study on the use of borehole breakouts to estimate in situ stresses at depth in a Canadian underground mine. Breakouts were identified using an acoustic televiewer (ATV) probe. Rock samples were tested in a laboratory to determine their failure curve. Breakout analyses were performed using a 2D failure criterion and a multiaxial failure criterion. Analyses were carried out using both short-term (peak) and long-term strengths (the latter considered here as being represented by the damage initiation threshold DIT). The analyses have shown that the use of the longterm strength and a multiaxial failure criterion leads to results that are more consistent with stress measurements performed in the field, in the vicinity of the mine.

Jun 1, 2012

By G. Tairova, M. Murchie, B. Esford, E. Lam

"The objective of this project is to investigate methods to lower the sulphate concentrations in the mill effluent. Currently, the concentration of sulphate in mill effluent is approximately 2 g/L. The high concentration of sulphate ion in the effluent has the potential to become a regulatory issue. The target sulphate concentration in mill effluent for this work was less than 500 mg/L. The pilot studies, using sulphate precipitation, were carried out at the mill. The results of the sulphate precipitation pilot study, using calcium hydroxide and sodium aluminate, indicated that:• The sulphate concentrations in effluent could be reduced to less than 500 mg/L.• The concentrations of most other elements of concern, such as selenium, arsenic, cobalt, nickel and vanadium, were also reduced.INTRODUCTIONHistorically, the concentration of sulphate, SO4 2-, in water has not generally been subject to regulation. However, with the increasing global consumption of water, stricter regulations on sulphate quantity may be imposed. Sulphate is a concern in process waters as it forms scale on process equipment and leads to operational problems. High sulphate concentrations may result in adverse health effects. The taste theshhold for the most sulphate salts in drinking water ranges from 250 to 500 mg/L.A literature search and review to identify methods to reduce sulphate concentration in the mill effluent was carried out. A number of methods were selected and tested in the lab. The experimental results indicated that the precipitation methods, using calcium hydroxide and aluminum compounds, barium compounds, as well as the ion exchange and the membrane methods, were effective for the removal of sulphate to below the required limits. Some other elements, such as vanadium, nickel, cobalt, selenium and molybdenum, were also removed.The process, using calcium hydroxide and aluminum compound for sulphate precipitation, similar to the Cost Effective Sulphate Removal (CESR), also known as “Walhalla” process, described in the Montana Tech report (“Demonstration Of Sulfate Removal” 1999), was selected for further consideration [1]. In the CESR process, the water is treated with lime for precipitation of gypsum, followed by the reaction with a proprietary aluminum compound for removal of a residual sulphate. The final pH adjustment is carried out using carbon dioxide. Results of a preliminary cost estimate indicated that the removal of sulphate using calcium hydroxide and aluminum compound was the preferred method of treatment, considering its low cost, availability of chemicals and minimal changes to the existing plant circuit."

Jan 1, 2012

By James E. Wennen

The through-put and energy efficiency of an autogenous (AG) grinding mill are adversely affected by variability in rock size and rock competency. This applies to both fully autogenous and semi-autogenous (SAG) grinding circuits. In this paper we focus on an approach to overcome the problem of inconsistent mill through-put related to variability in mill feed size and rock competency. The focus is on ores containing hard, competent rock. This approach consists of preparing feed to an autogenous mill that contains 20% coarse media rock and 80% of material crushed to pass 37 mm. Results of pilot-scale testing for two iron-ores will be presented to show that a 10% to 12% reduction in unit energy consumption is possible with prepared feed, compared with feeding the mill with conventional primary crusher discharge.

Jan 1, 2012

By Jonathan Ruiz Lizardo, Met-Chem Canada Inc., Flavio Ccuno, Constante Umipig, Ewald Pengel, José Ruiz

"Cerro de Maimón is located in the Dominican Republic on the island of Hispaniola approximately 75 kilometers northwest of the capital city, Santo Domingo. The processing facility consisted of two separate processing plants for oxide and sulphide ores. The oxide plant processed oxide ore bearing gold and silver ore using cyanide leaching and Merrill Crowe processes, while the sulphide plant produced a copper concentrate using conventional flotation. Cormidom is a commendatory example how mineral processing facilities can co-exist in balance with the environment. In 2014, natural occurring copper oxide contamination with finer grained copper-zinc sulphide mineralisation was expected to dominate the sulphide ore body. In anticipation Cormidom contacted the original plant designer Met-Chem to assist in overcoming this challenge. Test work indicated that increased flotation time and subsequent very fine grinding were required. Met-Chem provided the detailed engineering and Cormidom proceeded with the expansion project internally. Currently Cormidom has processed the sulphide ore successfully by implementing flotation modifications. This paper describes the history of Cormidom, test work on the “new” ore body, modification in process design in the Cu-Zn sulphide flotation circuit, construction and implementation.INTRODUCTIONCorporación Minera Dominicana (CORMIDOM) was a wholly owned subsidiary of GlobeStar Mining Corporation (a Canadian based minerals exploration company) with extensive exploration of base and precious metals in the Dominican Republic. In 2007-2008 CORMIDOM constructed the Cerro de Maimom project. The company was subsequently sold and purchased by Perilya Limited from Australia in 2013. Cerro de Maimón is located in the Dominican Republic on the island of Hispaniola approximately 75 kilometers northwest of the capital city, Santo Domingo. It is near the town of Maimón in Monsenor, Nouel Province (see Figure 1)."

Jan 1, 2016

The reliability of mining systems is generally low due to their harsh working conditions. Currently, efforts for improving mining system reliability are often made in isolation. This practice could substantially limit the effectiveness of the efforts on overall reliability improvement of the mining system. To enhance the overall reliability of mining systems, an integrated improvement approach is necessary. In this paper, we developed a framework for integrated mining system reliability improvement to address this issue. In this framework, there are five major components including data integration, business process integration, hardware integration, software integration, and analysis/decision integration, but we only focus on the integrated reliability analysis which is important to the analysis/decision integration. The reliability analysis considers the interactions between machines, and the impacts of design, operation, maintenance, automation and working environment on the overall system reliability. These multiple interactions present a big challenge to accurate reliability prediction. In this paper, we for the first time systematically investigated integrated reliability analysis approaches for dealing with this challenge using novel models and methods, including covariate hazard models, intelligent reliability prediction approach, and complex system modeling methods. While these models and methods have found some successful applications in other industries, they in general have not been effectively used for the reliability analysis of mining systems. Our study results show that the system integration approach is applicable to mining systems and can be used for developing a computer aided integration system for the implementation of the integrated reliability improvement approach.

Aug 1, 2013

By J. McCreedy

"The addition of Portland cement to hydraulic sand fill has resulted in the production of stable and self-supporting cemented sand fill. The use of cemented fill in the mines of The International Nickel Company has resulted in substantial economies in timber requirements, de-creased dilution of ore and greater flexibility in mining methods.Coupled with special mining techniques, it has permit-ted mining by both cut-and-fill and shrinkage stoping methods to much greater depths than heretofore. The use of cemented sand fill has permitted revisions to undercut-and-fill mining which have significantly improved the efficiency of this method.Automated mixing systems have been developed for preparing cemented sand fill in surface sand plants on a continuous throughput basis. Control of cement-sand mixtures is obtained by the use of a mass flow measuring system and weighing cement feeders."

Jan 1, 1966