Search Documents

By A Bennett, A Peck

BHP has recently constructed a Hot Briquetted Iron Plant at Port Hedland in the Pilbara region of Western Australia. Supply of iron ore fines to the plant is by conveyor from the companyÆs existing Nelson Point stockyards. The conveyor passes under Port Hedland harbour in a concrete segmentally lined tunnel, approximately 1030 m long and with a 5.1 m external diameter. The tunnel was constructed by a Tunnel Boring Machine (TBM) which both excavated the ground and erected the tunnel lining. The tunnel was bored between cut and cover in situ concrete portal structures, the TBM being launched from the Finucane Island side towards Port Hedland town. The alignment required lengthy gradients of 1:6 on either side of the harbourÆs dredged channel, under which the tunnel is bored with a minimum clearance of 8 m.The tunnel is fitted-out with:1800 mm belt conveyor capable of 10 000 tph;walkway along which a specially designed inspection/ maintenance vehicle can run; andtunnel services including power, light, fire detection and suppression communications, water mains for wash down and sumps and pumps for drainage.This paper gives a general overview of the design and construct contract, important aspects of the design and the construction process itself.

Jan 1, 1999

By J Jardine

An improved ground support method for development intersections, wide spans and stope brows was implemented at Kanmantoo mine. The method uses a jumbo to simultaneously drill and install self-drilling anchors (SDAs) to depths from 4.5 m to 7.0 m. Resin is subsequently pumped into each SDA using a specially designed integrated tool carrier basket, with plating occurring within 10 mins due to rapid resin cure. This methodology means that SDAs can be installed rapidly due to reduced process steps and wait times with reduced hazards to personnel. Cablebolts are used extensively in underground mines to reinforce the ground in wide spans, such as at intersections and stope brows. The flexible cablebolt tendon allows for a long, continuous and high-capacity reinforcing element to be inserted into the rock. A common cablebolt installation practice at Australian underground mines that do not utilise a mechanised cable bolter, is for cablebolt holes to be drilled by a jumbo or longhole rig, hand installation and grouting by a service crew, then plate tensioning following a grout curing wait time of typically 12 to 24 hours. This process involves multiple separate labour-intensive work processes and results in reduced availability of priority headings. This paper discusses the development history of vertical SDA use in wide spans at Kanmantoo mine. The installation process is fully described, including aspects such as reliable in-hole coupling of SDAs, resin selection and pumping aspects. A cost benefit assessment, and a case for ground stability are presented to compare cablebolt use to SDAs in development intersections.

Mar 29, 2023

By J Moffatt, T Payten, N Spooner, L Teixeira, L A. Balzan, G Wilkie, G Tsiminis

Fluorine is a penalty element due to its reactive nature. In acidic environments many fluorine minerals dissolve to form hydrofluoric acid (HF), changing processing conditions. When smelted HF can be released, causing negative effects to nearby people and the environment, as well as potentially damaging the smelter. Sale of ore with high fluorine levels elicit a financial penalty or are banned outright. Real-time sensors create the opportunity for instantaneous decisions on ore processing due to changing conditions. A fluorine sensor would allow rises in fluorine concentration in a processing stream to be flagged, and decisions on processing conditions or diversion to stockpile before processing could be undertaken. As fluorine is a light element, it is difficult to detect with in-field XRF devices and does not work well with PGNAA. There are currently no existing sensors to quantify the presence of fluorine in real-time, and thus decisions based on fluorine grade cannot be made at minute- or even hour-scales. Sensors designed to measure the presence of minerals that contain fluorine are a possible avenue to enable the real-time detection of this element. Mineral-based sensing may also give an added advantage of additional information about how the fluorine will react under different processing steps. The authors were given a grant under CRC ORE II (project number P1–005) to search for mineralspecific signatures suitable for real-time analysis. The work focused on novel regimes and applications of fluorescence as a means to detect specific minerals. The aim was to exploit fluorescence responses unique to minerals of interest in mining systems in order to produce sensors that address gaps in existing capability. After the successful discovery of signatures specific to two major fluorine minerals an additional grant (P1–014) was funded to develop the research into a prototype on-belt sensor, in partnership with Scantech International Pty Ltd. This paper details the development of a sensor package through multiple Technology Readiness Levels (TRLs) through collaboration with government/industry grant schemes, academics from university, and a sensor-focused Mining Equipment and Technology Services (METS) company. We give a brief description of the new sensor technique and provide a case study of multi-disciplinary collaboration.

Aug 24, 2022

This paper discusses equipment replacement strategies and specifically addresses the upgrading of technologically superseded equipment. The process of equipment replacement evaluations is reviewed, and areas have been highlighted where currently accepted practice results in a bias towards retaining existing equipment longer than otherwise justified. The Discounted Average Cost Method is described and the advantages of the technique for this style of decision making discussed. Several key issues influencing the replacement evaluation are also presented together with examples from recent consulting work.

Jan 1, 1992

By L H. G McClean

Environmental, social and governance (ESG) factors have always been important to the minerals industry and is now considered one of our most important opportunities (and risks). Getting it right from the beginning is critical for the minerals industry, and that starts with mineral exploration. Exploration, or the process of investigation of an economic mineral deposit, is generally low impact and short-term. Exploration operations vary in size and scale and often shift priority, focus and location relatively quickly. Australia is a highly regulated jurisdiction with different regulatory systems and requirements in every state and territory. Most mineral exploration is undertaken by junior exploration companies or ‘explorers’. Exploration companies are lean operations with limited staffing and resources, traditionally with no income apart from funds raised or work through partnerships. Funds are tight and administrative investment is minimised so that investment into activity on the ground is maximised. All these variables mean that understanding and implementation of ESG frameworks for an exploration company can be challenging. ESG is a fast-moving sector with currently multiple frameworks and reporting standards. Interest from community and government stakeholders as well as investors and off-take partners has been growing, with mandatory reporting soon to be implemented. The upcoming changes to the JORC Code will ensure that ESG considerations will be a key component of all public reporting. Resources have been developed to support explorers implement, manage and report on ESG considerations. Due to their scale, agility and direct importance of land access and social licence, many explorers are not the ‘cowboys’ (or ‘cowpersons’) of the industry, but industry leaders in ESG. Strong interest and leadership have led to innovative practices and strongly embedded vertical frameworks that directly contribute to social licence to operate.

Sep 1, 2024

By M Barkh, F X. Spachtholz

The mining industry faces significant environmental challenges in managing tailing ponds and wastewater treatment, including the risk of contaminated water, breaches of tailing dams, and energy-intensive treatment processes. Traditional methods involve pumping water to secondary treatment facilities for neutralisation, which is costly and poses operational and environmental risks. In response to these challenges, the Professional Mine Water Action Plan (PMAP) introduces a revolutionary approach that combines cutting-edge AI technology and environmentally friendly reagents for in situ neutralisation of acidic wastewater. PMAP leverages magnesium-based slowrelease reagents and AI-driven intelligent dispensing systems to optimise treatment processes within the tailing pond itself. The unmanned smart dispensing vessel (USDV) conducts bathymetry to gather data on water quality and hydrography, allowing the system to determine the appropriate reagent quantity and injection strategy. This approach transforms the tailing pond into virtual reaction columns, enabling individual and simultaneous water treatment while optimising efficiency. PMAP’s novel reagent demonstrates exceptional efficacy in removing critical metals like cobalt, nickel, and copper, as well as reducing harmful metals such as mercury and manganese to undetectable concentrations. Unlike traditional lime-based treatments, PMAP’s reagent prevents gypsum formation and reduces waste volume significantly, improving reagent utilisation and solid waste handling. Furthermore, PMAP technology offers benefits beyond environmental stewardship. By reducing water treatment costs and improving resource management, it enhances operational efficiency and aligns with broader corporate sustainability goals. Additionally, PMAP expedites permitting processes by eliminating the need for traditional water treatment infrastructure and mitigating risks associated with hazardous reagent transportation. Integrating PMAP as a pre-treatment for existing lime facilities provides further benefits, including optimisation of treatment operations, reduced reagent consumption, and the recovery of valuable metals from generated sludges. Overall, PMAP represents a groundbreaking advancement in mining wastewater management, showcasing the transformative potential of AI and environmentally friendly solutions to foster sustainable and responsible mining practices globally. Its inaugural project in the Yukon Territory aims to demonstrate its capability to remove contaminants from mine water, paving the way for widespread adoption in the industry.

Sep 1, 2024

By D M R Stone

Failings di,posal presents many challenges at metal mines in Peru where the extreme relief yields very little useable land area. These challenges are amplified by other hazards such as the high seismic environment, high rainfall, and frequent debris torrents down the steep hillsides. As a result many mining operations have resorted to in-river disposal of mill tailings. This paper presents a case history of one underground metal mine located in the high Andes mountains of Peru where in-river disposal of tailings has been used for some 30 years. The paper outlines a comprehensive engineering study that was aimed at increasing the utilisation of tailings disposal underground. The scope of this study included modifications to the grinding and flotation circuits to produce a high sulphide and low sulphide tailings for underground and surface disposal respectively: mapping and cataloguing of abandoned stopes for hackfilling: modifications to the existing backfill system to improve icliahility and throughput, and a preliminary evaluation of alternatives Such as silicated and paste fills.

Jan 1, 1998

By D Drinkwater

In 2009, Peter Munro and Peter Tilyard examined the “human capital” in the mineral processing sector in a paper entitled Back to the Future (Munro and Tilyard, 2009). One of their major concerns was a general decline in technical skills and process knowledge, exacerbated by lack of appreciation of the impact this can have on process plant performance and, ultimately, profitability or sustainability of the industry. There are many reasons for this decline, not least of which are the work schedules of today’s metallurgists which have a very different balance between technical and non-technical responsibility than those in the past. However, a shift towards a more technical focus has potential to deliver a range of benefits for industry at large and for the individuals in it This paper discusses some options for development of core metallurgical and process engineering skills that can be used by graduates, employers and training providers.Key skills are identified and mapped against available opportunities for development, such as existing graduate programs, on-the job training and external courses. The authors also review a number of past and present high-quality graduate development programs, including the graduate development program in place at Mount Isa Mines in the 1980s and the Anglo Platinum Graduate Development Program (AGDP) currently operating in South Africa.

Aug 8, 2011

Coal mining legislation makes frequent reference to æSafety Management SystemsÆ but there is a chronic shortage of useful guidance material as to how these might be applied to hazardous exposures. Several studies have indicated that for each death that is reported as a result of an industrial æaccidentÆ, there are five deaths that caused by occupational exposures. Because the deaths from occupational exposures do not occur on site and often well after employment has ceased, they are generally unreported. Improved access to mortality data from coroners, the Australian Institute of Health and Welfare and superannuation service providers (early claims from death and total permanent disability), has given rise to some analysis of death and disability data that provides evidence that there are emerging opportunities to develop and improve safety management systems for hazardous occupational exposures. Issues explored include how safety management systems might be developed in relation to dusts and chemicals and other hazardous exposures to ensure the risk of disorders with long latency periods are reliably assessed and the exposures effectively managed. The current standards and guidelines which refer to safety management systems in general or to management of exposure related hazards are examined. Many standards are based on dose-response studies that provide for an acceptable percentage of workers to suffer adverse health outcomes. An alternative management system might be to apply dose-response relations to health surveillance to identify æat riskÆ individuals and effectively manage health and related safety risk at an early stage.

Jan 1, 2005

By J Centofanti, D Conti, R Riske, C Morley, A Cook

Why is it so difficult? Why are there differences throughout the resources industry in how reconciliation factors are reported and calculated? Why is there no standard formula to use? These are common questions asked when mining companies try to compare reconciliation results across operations or attempt to undertake internal or corporate governance reporting processes. For many mining companies the calculation of reconciliation factors is often a very time and resource intensive part of mandatory reconciliation reporting. Some major mining companies, that move millions of tonnes of material per annum, dedicate full time resources to the calculation of reconciliation factors. The willingness of these companies to set aside resources demonstrates the value that operations place on good reconciliation reporting. Reconciliation is about measuring the variance between two like measures at different points along the mining sequence. It can be undertaken between predictive models, forecast plans and actual measured performance. Calculations are used to derive a variance between two sections within the mining sequence, with the result being commonly known in the resources industry as a æfactorÆ. Mining companies use the calculation of reconciliation factors as key performance indices (KPIs) to provide a æhealth checkÆ of their operation, with variances often pointing to issues either with the accuracy of the original estimate or the quality of the measurement being used in the comparison. There are many reconciliation factors that can be calculated and reported. This paper will set out, clarify and provide a recommended standard means of calculating each specific factor that, where adopted by a company, will ensure compliance with the international reporting codes, such as JORC. Using case studies from Rio Tinto Group (Rio Tinto) and BHP Billiton Mitsubishi Alliance (æBMAÆ), and the authors experience across a wide range of mine sites, the outline of a generic solution for tracking a parcel of material from the pit through to the port along with appropriate reconciliation factors is provided. The intention of proposing standardised reconciliation factor terminology and methodology is to provide the foundations of a system to enable communication and comparison across different commodities, companies and mines sites.

Jan 1, 2009

By C Yeung, N Swa, D Gribble, R Reupana

BlastLiteÖ is a low density explosive developed by Dyno Nobel and has been in use at BHP Billiton Iron OreÆs Mt Whaleback Operation since March 2004. The Mt Whaleback Operation utilises BlastLite because it offers an attractive alternative to ANFO in soft to medium strength rock types. Its use also reduces the amount of liquid fuel oil consumed and is well aligned with BHP BillitonÆs corporate Energy Excellence initiatives to reduce greenhouse gas emissions. This paper presents the:results of characterisation work completed on-site as a fourth year mining engineering thesis, and application and benefits of the product at Mt Whaleback. One of the key features of low density products is that the detonation is non-ideal. That is, the explosive does not react fully in the detonation driving zone. This manifests itself in that the product is highly dependent on charge diameter and confinement conditions. Dyno Nobel has access to the Vixen suite of detonation codes for characterising the ideal and non-ideal behaviour of explosives. The objectives of this work were to use the Vixen_i code to characterise the detonation performance of BlastLite, in order to understand the role of the bulking agent and to allow modelling of the explosive. The detonation performance was established by detonating a series of unconfined charges at various diameters and measuring the velocity of detonation (VoD). The work program consisted of sourcing and preparing cardboard tubes of various diameters (80 mm to 305 mm). The tubes were loaded with explosive at the BHP Billiton Iron Ore Mt Whaleback test range and detonated one at a time. Over the past three years BlastLite has been used in various applications across the site. Initial findings illustrate that shovel productivity from BlastLite shots was comparable to the baseline ANFO blasts. The study results were also backed with visual inspection and feedback from shovel operators. A work program is currently in place to develop different blends of BlastLite and TITAN« BlastLite to tailor the explosives to various blasting applications. The trials at Mt Whaleback are leading to future opportunities of BHP BillitonÆs satellite orebodies.

Jan 1, 2007

By A Havenga, F, J Hough, R Grobbelaar

After the closure of mines they naturally start to fill up with water. As a result, hydraulic gradients develop between adjacent mines and different hydraulic water pressures are exerted onto peripheral areas or compartments within mines. This results in water flow between mines, or onto the surface. This flow is referred to as intermine flow. The geometry of the collieries in the central Witbank Coalfield make intermine flow possible in several areas. Since the Department of Water Affairs and Forestry declared intermine flow as one of its greatest concerns for granting closure to South African mines, much research into this phenomenon has been undertaken. The importance of the quantification lies in the DepartmentÆs goal of sustainable water management, and the possible long-term financial implications these flows could have for individual mines. The challenges of determining intermine flow are numerous, and attention is focused on the identification of areas where these flows can take place. Detailed mining plans on a regional scale are required, and detailed coal-seam floor data are combined to provide targets for possible interaction between these mines. The quantification of these flows is problematic due to the uncertainties regarding geometrical configurations and the variation in site-specific hydraulic characteristics of the coal and overlying lithilogical layers. To this end, use has been made of several analytic solutions and numerical flow modelling. Stage curves (volume versus elevation curves) for the opencast and underground workings have been calculated and first-order estimates for intermine flow or decant from these areas have been determined. The numerical modelling methodology entailed a down-scaling approach, starting with a broad regional model covering the entire area, followed by modelling the interactions between interconnected mines and finally looking in detail at the major areas of interaction. By considering different scenarios within the context of these flows, possible management options for intermine flow can be evaluated in terms of volumes and qualities that might emanate in the post-closure phases. Challenges for the future include obtaining site-specific information on the groundwater hydraulics and acceptable ranges for model parameters, and verifying model results over time.

Jan 1, 2003

By T Laurencont, C Unger

The Mount Morgan minesite, located approximately 40 km SW of Rockhampton in Central Queensland, comprises 270 ha of unrehabilitated land which is the currently the major source of acid mine drainage run-off and seepage to the adjacent Dee River. Additionally, the minesite hosts an Open Cut Pit which contains 9000 ML of acidic and metal-rich water. In the absence of active management of water in the pit, there is a 50 per cent probability of an uncontrolled spill occurring in future years. The development of a contingency plan for management of overflow from the pit in the short term, has incorporated findings from numerous studies relevant to the Open Cut Pit including, but not limited to, water balance, contaminant source identification, toxicity testing, water quality profiling and limnological modelling, and estimates of probability of overflow. Extensive stakeholder consultation and peer review were also undertaken during the formulation of the contingency plan. The medium-term goal of lowering the water level in the pit to reduce the current high probability (50 per cent) of uncontrolled overflow to acceptable levels of risk is proposed to be achieved by a campaign of chemical water treatment. The treated water will be discharged to the Dee River, and sludge returned to the pit. The methodologies used for the selection and development of the water treatment process, that is proposed to involve treatment with lime, are described. Water treatment is the short- to medium-term component of a long range rehabilitation plan for achieving a negative pit water balance, and sustainable management of acidic water across the whole site. Achieving this ultimate goal will involve: reducing the inputs of water to the Open Cut Pit such that the annual water balance is zero or net negative, thus removing the need for water treatment in perpetuity; maximising, by surface rehabilitation works, the quality of run-off reporting to the Dee River; and minimising the volume of acidic seepage reporting to the seepage interception system. Possible strategies for achieving this long range goal consistent with overall site rehabilitation objectives are currently being developed and costed.

Jan 1, 2003

By J Hutchings

An essential component to the management of any process is the measurement of key parameters, used to monitor, control, and provide the feedback necessary for improvement. This paper discusses how data collection and analysis can provide a better understanding of the blasting process, as well as additional control and improved outcomes.The drill and blast process involves the generation and use of information at a number of levels. Comparison of historical parameters and results provides a starting point for the development of ongoing blast designs and a baseline against which future results can be compared. The collection of data during implementation provides a quality assurance/quality control (QA/QC) function where potential defects (such as under-drilled or over-charged holes) can be rectified prior to firing. Actual quantities and production rates allow the development of realistic plans and schedules, rather than using inaccurate estimates and targets that lead to unscheduled changes to equipment paths. Over?the past several years there have been a number of technological advances in data collection technology. Drill monitoring instrumentation on blasthole drills provides location information and feedback on rock properties as drilling occurs. Hand held ‘data logger’ technology has also overcome the challenges of working on the bench, such that blasthole measurements can be collected and forwarded directly to the explosive truck. Mine sites are becoming wireless network-enabled allowing the seamless data transfer from the field back to the office, in near real time, as that information is collected. Great strides have also been made in the development of drill and blast software systems which are more user friendly, and yet provide far greater capability to manage the quantity of data generated. The blasting process is critical to the overall mining process and the delivery of a successful blast outcome requires that the blasting process be ‘in control’. The measurement of key parameters can provide the data with which to measure and maintain control of blasting, and allows the validation of performance improvement measures and identification of improvement opportunities.

Nov 8, 2011

By D Preedy, J K. Claflin, S R. J La Brooy

This paper summarises the lessons learned during a recent carbon reactivation kiln upgrade project at the Sukari Gold Mine in Egypt. The kiln is being replaced to ensure that the plant achieves full value from the current throughput expansion from 5 to 10 Mt/a.The suitability of the original engineering design criteria for kiln selection and the adequacy of the original kiln are reviewed in the light of the carbon chemistry, operating experience and a site inspection of the kiln. Particular aspects of the reactivation facility are discussed including: predrying, preheating, feeding, gas seals, kiln heat transfer, steam injection, counter-current sweep gas flow, carbon cooling, fines minimisation and removal.Design criteria for a carbon predryer, reactivation kiln and cooler combination for carbon heavily fouled by high molecular weight frothers and collectors are discussed and the abridged Ausenco datasheet for the combination is presented.Responses to a request for a budget price sent to most of the worldÆs suppliers of carbon regeneration kilns are summarised.CITATION:Claflin, J K, La Brooy, S R J and Preedy, D, 2013. Ausenco carbon reactivation design criteria, in Proceedings World Gold 2013 , pp 401-410 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By E Beltran, S Ngunz, F Orrante, F van Zyl, M Westcott

"The primary control objective of the project is to achieve milling optimisation by ensuring that the energy available for rock breakage is used as efficiently as possible. This is achieved by increasing the level of mill filing until a process constraint is reached. Stable operation against this limiting constraint is then maintained to ensure long-term optimised operation.Semi-autogenous grinding (SAG) mill control optimisation presents a number of challenges. SAG mills have multiple inputs that are used to control multiple outputs (MIMO process). Secondly, the SAG mill loading process is a ‘high inertia’ process that can be approximated as an integrating process. This means that it is open-loop unstable. The hybrid control strategy presented implements an advanced ‘load stabiliser’, which transforms this integrator process into a more manageable first order process, which can be steered stably against the constraints. This SGS hybrid Expert control strategy implemented on both SAG mills at the Porgera concentrator therefore consists of two integrated parts responsible for:stabilising the mill load to a targetdriving the mill load target to the maximum determined by the process constraints (eg maximum power draw) to maximise efficiency and throughput. A comparative study is done between the operation of the plant for a period of a month before and a month after the implementation of this strategy. The results indicated a significant improvement in the SAG mills’ stability and operation as well as a reduction of overload situations leading to a loss of throughput.Citation:Ngunz, S, van Zyl, F, Orrante, F, Beltran, E, Westcott, M and Wilson, S, 2016. Simplified Hybrid Semi-autogenous Grinding Mill Control - Explanation and Practical Results at the Porgera Concentrator, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 313–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

The information age has arrived. In every aspect of life, at the end of the second millennium, computers and information technology have made significant inroads. In mining there has been huge growth in the use of digitally controlled systems. From resource evaluation to mine planning to daily operations, information is being acquired, analysed, modeled and presented, using state-of-the-art information technology. Explosives, too, have moved into the information age. Computer controlled trucks and manufacturing plants have been developed and are now a regular feature on many mine benches. The next challenge for the explosives industry as a whole is to integrate blast initiation with information technology. The benefits are there, both to the supplier and to the end-user. Much has been written in the past about the potential for blast improvement but there are other significant advantages to a digital initiation system. These include security from unauthorised use, stock control and minimisation, reliability through testability and ease of use to name a few. So why is it taking so long? Surely the complexity of an electronic initiation system is far less than that of mobile phones that have been around for a long time. The answer, it seems, lies in the level of new technologies that need to be developed. There are enormous technological hurdles to be overcome in order to put into the market a cost-effective, reliable, user-friendly electronic initiation system. The most significant of these are:Safely and reliably initiating an explosive from an electronic device powered by a small capacitor. Prior to the development of electronic detonators primary initiation of explosives was by shock tube spit or by passing large currents and voltages down a pair of wires. Electronic detonators do not have that luxury. For example the energy stored in a æBeethovenÆ exploder is more than 500 times greater than that available to an electronic detonator. Communicating to a multitude of devices over very long cables installed by miners in harsh conditions. The deployment of an electronic detonator system has been likened to building a large telephone exchange in the rain and getting it to work perfectly first time! New communications protocols needed to be developed and tested. Wiring and connection systems have to be designed to survive the mining environment. In spite of these technological hurdles most of the major explosives manufacturers have persisted with electronic initiation systems and we are now, in 1999, starting to see the results of these multi-million dollar efforts. At SMI we are often asked many questions about this technology. The remainder of this paper seeks to answer those most often asked. As with any business linked to information technology todayÆs breaking news is tomorrowÆs archive and we expect the rate of development and understanding to accelerate as these technologies become accepted by the global mining industry.

Jan 1, 1999

By M Rauer

With a worldwide growing population the demand for higher living standards, food and the development of new technology is rapidly rising. To allow for a continuous growth, larger quantities of minerals and raw materials are needed at a faster pace. Different methods have been developed to access or tap ore more quickly, such as improved drill and blast operations, mechanical mining methods using equipment such as roadheaders (RH), longwall miners and other technical equipment. Another possibility to access and develop mines faster is the use of a tunnel boring machine (TBM).The historical usage of TBMs is surprisingly long, but the opportunity for technology adoption by the majority of worldwide mining companies remains largely untapped. Dozens of full face TBMs have been used by mines around the world, including two that will begin operation soon in Australia. TBMs have been used to safely and rapidly gain access to the orebody, or to expand access to the orebody to increase output by running a TBM along the edge of the orebody for several kilometres. These machines have also been used for ventilation and for conveyor tunnels for ore removal. They have been used to quickly excavate long and winding declines giving access to an orebody at several levels in a short period of time.Tunnel boring technology can be used for mine declines, mine access tunnels and all sorts of different mine designs and set-ups. TBM technology simply needs to be adapted to the mine conditions and, if manufacturers are involved early on in the planning process for mine development, the operation can be very successful. In some cases, historically typical mine designs may need to be re-thought.One mine, the Stillwater Platinum mine in Nye, Montana, is currently employing its fourth TBM in 25 years. Two were used to create tunnels running alongside the orebody, rapidly expanding access to the orebody in many locations for increased output. Two were used to create parallel access tunnels to a mine expansion at the East Boulder orebody; one tunnel is for conveyor haulage and the other for vehicular access. TBMs have been employed successfully many times to rapidly drive vehicular decline tunnels to multiple mine levels, such as at the San Manuel – Magma Copper mine in the USA. While TBM technology may not seem to be optimal for every mine, these success stories show that the method can provide vast benefits for the right projects.Early use of TBMs in extremely hard rock metal mines, in the 1960s and 1970s, had limited success since performance was low. However there have been great improvements made over the years in the strength of rock which can be excavated by TBMs with high performance. Other important improvements involve the provision of a safe work environment, safely and rapidly supporting the rock and predicting geology ahead of the TBM.This paper will briefly note the more than 20 TBM mining projects and highlight some notable successes. It will then go on to give a status report on the two active TBM mining projects in Australia and the difference between a TBM operation versus other excavation methods such as drill and blast (D&B) or RH excavation.CITATION:Rauer, M, 2014. Tunnel boring machines in mines – a?brief review of past use with a status report on use today in Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 663–670 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By J Seccatore, T Marin, M Cardu, G De Tomi, F Galvão, A Rezende, E Melo

Small-scale mining operations are characterised by a large variety of equipment availability and a high level of operational flexibility. Mine planning is usually scarce or absent in small quarries in Brazil, and mine management generally focuses on daily operations. As a result, analysis of the effects of unit operations, such as blasting, over the whole mining process is often neglected. The goal of the following project was to study the effect of production blasting on loading and hauling times, secondary breaking times and primary crushing times at the Experimental Mine of the Research Center for Responsible Mining of the University of São Paulo, Brazil. The operations analysed included blasts that performed:under the average operational standard, defined in this paper as Case 1according to quarry standards, defined in this paper as Case 2.In order to establish the effects of blasting on the downstream process, three key performance indictors were used:The time taken to load the truck, when there is the need for material selection. Due to the fact that we do not have an operational baseline, the increase in time cannot be established, meaning that we must content ourselves with comparing the mean time in each scenario.The average time used for secondary breaking machinery.The time required for the primary crusher to fully process the load of a single truck. The results obtained indicate correlations between the coarseness of the blasted material and these operational times. Solutions are suggested and evaluated for the improvement of the small-scale mining process.CITATION:Marin, T, Melo, E, Seccatore, J, Cardu, M, Galvão, F, Rezende, A, Bettencourt, J and De Tomi, G, 2015. The effect of drilling and blasting performance on fragmentation in a quarry and time for loading, secondary breakage and crushing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 355–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By S Thomas, E Grimsey

Mining education in Australia has undergone another cyclical downturn over the past five years and several departments have been discontinued while others are still teetering on the brink of destruction. During this downturn Curtin UniversityÆs WA School of Mines (WASM) has managed to stay alive and well, but this has not been by accident. This paper outlines some of the strategies and experiences that have kept WASM in a strong position and offers hope to other departments and schools elsewhere that are still experiencing difficulty. This paper is also directed at all mining departments and schools that are certainly going to see it all happen again after the next mining boom turns to bust.

Jan 1, 2004