Search Documents

By P Clark

This paper discusses the challenges, solutions and lessons learnt as tunnelling work continues on the Melbourne Main Sewer Replacement (MMSR) project.The MMSR project is a $220 million dollar project for the Melbourne Water Corporation. It involves the construction of approximately 4.2 km of new sewer from the southern fringe of the CBD through the inner metropolitan suburbs of Port Melbourne and South Melbourne.Of the 4.2 km of sewer currently in construction approximately 2.2 km will be constructed using a 2.95 m diameter Lovat EPB tunnel boring machine (TBM) with approximately 1.9 km of small diameter (300 to 600 mm) reticulation sewers constructed using trenchless techniques.These sewers are being constructed in a dense urban environment, which means that the tunnels and shafts are often in close proximity to buildings and structures. The underground constructionof the sewer is further complicated by the variable geology of the ancient Yarra River delta which includes weathered basalts, the infamous Coode island silt formation and fine loose sands.Some of the key challenges and lessons learnt so far during construction include:· steering and alignment control of the TBM through very soft silt with little residual strength,· development and refinement of a monitoring and alarm system for leaving the machine dormant on a day works only project,· control and measurement of tunnel lining defl ection during ring build and grouting,· prediction and monitoring of surface settlements during tunnel excavation,· improved understanding of the geology and hydrogeology at this previously unchartered area of Melbourne,· consolidation settlement due to dewatering at shafts required careful construction controls, and· ground support and excavation in close proximity to the existing 110 year old sewer which requiredvery detailed risk control measures.

Mar 8, 2011

By C K. McKenzie

As more and more mining operations around the world either switch to, or trial, electronic initiation systems, the breadth of knowledge and experience regarding their effective application has widened considerably.In South America, for example, there is a strong perception that in order to achieve the finest possible fragmentation, very short electronic delays must be used between successive holes within a row. Limited field studies involving measurement of fragmentation have been conducted to support that paradigm and there are few long term studies which have been strongly supported by measurements of productivity either in the pit, in the plant, or in the leaching pads.On the other hand, some well documented studies have been conducted in North America, showing not only the impact of delay timing on fragmentation but also the effect on semi-autogenous grinding (SAG) mill productivity over extended periods of in excess of 12 months. To date, those studies suggest that optimum timing is considerably longer than the times commonly used in South America.This paper explores the current knowledge of the effects of delay timing on issues ranging from size distribution to vibration impacts in pit walls, to vibration and overpressure impacts in surrounding communities. It also explores how fragmentation modelling can be adapted to reflect fragmentation trends that have been reported in various technical conferences around the world.

Nov 8, 2011

By White A. H, Gillies A. D S

In recent years the Australian gold industry has gone through a major expansion phase. The need for finance has led to adoption of different approaches such as the well known gold loan, forward selling, equity participation by suppliers and equipment leasing. During early periods of the expansion, significant new equity was raised chiefly for high risk exploration ventures. The major form of new equity finance was ordinary shares, often in 'No Liability' companies. The increasing capital requirement of the huge new development projects of the 1980s also spurred the use of debt finance. This trend was accelerated as high inflation and the taxation advantages of debt finance made borrowing attractive. This paper reviews major financing techniques used by the Australian gold industry with particular emphasis on the innovative financing techniques initiated recently. An analysis has been undertaken of the effects on the industry of issues such gold loans, forward selling, equity participation by suppliers, fly-in fly-out operations, contractor mining and equipment leasing. In order to achieve a better understanding of the innovative financing techniques, a survey of already published financial data from well known Australian gold mines was carried out. Data was collected from various published financial reports of gold mining companies. In addition, a questionnaire survey was sent to gold mining companies to assist the collection of further information. The results of this study show that there are a significant number of gold mines variously using gold loans, forward sales, contractor mining and fly-in and fly-out arrangements to finance their projects. Only four operations have vendor suppliers investing capital funds in their projects. Based on the findings of this study, conclusions and recommendations are drawn that these approaches are likely to be with Australian gold industry for some time in the future and will continue to be intensively applied to finance gold projects.

Jan 1, 1994

By T A. Short, P L. Brown

Kestrel Mine co-disposes around 1.5 Mt of fine (2SO4/t and to date around 9 Mt has been deposited. The mine plans to co-dispose of approximately 39 Mt of material, creating a dump with a maximum height of 35 m and a disturbance footprint of 260 ha. Benign materials suitable for rehabilitation are severely limited and no successful rehabilitation strategy has yet been demonstrated. A rigorous measurement and modelling program is resolving outstanding issues associated with acid rock drainage (ARD). The objective of the program is to develop and validate a strategy for dump rehabilitation that will control ARD and allow for mine closure. The strategy includes using a soil cover to reduce water flux into the dump to control the overall oxidation rate and to control effluent release. Monitoring of the oxygen distribution and water flux in the uncovered material commenced in February 2001 and monitoring in waste under a trial cover commenced in February 2002. Carbonaceous and sulfidic oxidation rates have been measured. Initial modelling indicates that the carbonaceous material has the general effect of slowing the rate of pyrite oxidation, lowering the maximum sulfate production rate and extending the time to oxidise all the sulfides. The combined approach of measurement and modelling provides a sound basis for assessing the performance of the trial cover and predicting the long-term quality and quantity of effluent at the base of the rehabilitated waste dump.

Jan 1, 2003

Societal expectations about how the industry operates and treats its people will be a key driver in the development of the Australian mining industry over the next 20 - 30 years (Moffat, Mason and Littleboy, 2009). Understanding these expectations will be critical in maintaining what much of the minerals industry calls its 'social licence to operate', or its public acceptance or approval. Yet what constitutes this social licence is poorly articulated, with little published research exploring the concept at a local operational level or at the national level in Australia or internationally. This research aimed to explore the societal expectations of the mining industry in Australia and test a participatory methodology to articulate them. Three workshops were conducted with a sample of 24 members of the 'Australian voting public' to explore community objectives for the onshore exploration and mining industry, and the underlying expectations for how the industry should operate in the future. Qualitative analysis of this data revealed three overarching objectives for the onshore mining industry held by participants. They thought that the industry should: advance Australia's national interests (including social well-being); minimise environmental impact, and; act in a socially responsible manner. Within each of these three key themes, or objectives, a number of tensions were evident in the views of participants regarding the trade-offs they are willing to make to secure economic benefit from mining, as well as the basic conditions for socially acceptable mining. These data provide an insight into the conditions for a national social licence in Australia for the mining industry, and the means for its realisation.

Jun 1, 2010

By M Watson, A V. Engelbrecht, E Murray-Hayden

Whereas mine reconciliation is a well-established month-end process for most modern mining operations, the resource sector has yet to endorse uniform reporting factors against which model accuracy and metal recovery can be formally assessed. Logically, any comprehensive reconciliation framework should facilitate comparison between period reserve, mine and mill and production figures. Historically, Parker’s F Series ratios (Parker, 2012) are often used in some form by mine operators, although they are rarely shared externally, as formal definitions have yet to be accepted. This paper presents a structural extension to the reconciliation process, wherein resource ratios (R Series factors) are used to quantify the long-term impact of the information effect, together with dilution and ore loss. A case study from the El Limón Guajes (ELG) Mine Complex in Mexico is used to demonstrate how an R Factor Series can be implemented to facilitate operation optimisation, over and above conventional F Series reconciliation treatments. This approach is applicable to any mining operation.

Mar 22, 2022

By J Leem, S Mehrishal, J Kim, A Fereshtenejad, J Song

Rock mass discontinuity mapping plays a crucial role in developing a reliable Discrete Fracture Network (DFN), providing insights into the distribution of geometrical and mechanical properties of discontinuities. This enables an accurate assessment of geotechnical infrastructure and mining excavations. Data obtained through conventional mapping approaches are substantially limited by factors such as accessibility and subjectivity. Moreover, these conventional methods may pose inherent risks due to manual techniques, exposing practitioners to potential dangers. Recent digital developments in remote surveying techniques offer opportunities for safer and more reliable rock mass discontinuity surveys. These technologies allow extensive three-dimensional surveying and the production of high-resolution 3D surface models, applicable at any time. This paper presents a workflow for digital discontinuity mapping employing drone technology and photogrammetry. Additionally, the capabilities and challenges of applying artificial intelligence (AI) algorithms in the rock mass discontinuity characterisation process are discussed.

Sep 1, 2024

By G J. Wilkie, P A. Revell

The R&D landscape for ore pre-concentration technologies within mining is characterised by the development of individual technologies and point solutions. This presents METS and mining companies with the combined challenge of understanding how to apply pre-concentration technologies to create maximum value, and how to sustainably integrate the technologies into their businesses to maintain the value. The paper will consider the requirements of an integrated pre-concentration system and presents a portfolio of R&D projects that have co-developed and integrated a suite of new precencentration technologies and methodologies across the mining value chain. Focus areas include in-situ orebody characterisation, blast design, real time cross belt mineral sensing, and consideration of how much data needs to be acquired in order to make value based decisions between ore pre-concentration options. An ore pre-concentration workflow is presented to demonstrate how additional optimisation opportunities are enabled both by moving decision points further upstream in the value chain, and by integrating the concepts of pre-concentration into the design of mineral processing equipment. Additionally, several research projects examine the non-technical factors that present barriers to uptake of new technologies within mining companies. Organisational culture, risk management and socio-political factors are discussed and a set of management tools are presented that allow organisations to self-assess their readiness for new technology uptake, along with process models to assist management with identifying and navigating the ecosystem of stakeholders that are decision makers in the use of pre-concentration technologies.

Nov 10, 2020

By C Garrido, J Barrera, H Alvarez, L Perez, S Ramirez

In recent years, there has had a greater recurrence of studies and projects that consider tailings filtration followed by dry stacking to reduce the consumption of fresh water, the space required for disposal, and, eventually, to reduce the costs of the project. In addition, this technique could be required to meet new environmental restrictions to extend the life-of-mine of existing plants or to enable the development of new projects, especially in areas of high social interest. This article is intended to describe the most relevant technical aspects of the design and implementation of an iron ore tailings filtering system and its final overland disposal as well as physical and metallurgical surveys, and laboratory and pilot testing. Furthermore, it is presented how these activities are inserted in the project development to rationalise the resources. The case under study considers an iron mineral wet magnetic concentration processing plant. The outcome tailings are dewatered by means of thickeners, where the overflow water is recycled back to the plant. The underflow slurry is pumped into intermediate storage tanks before proceeding with further dewatering and final disposal. The project consists of a tailings filtration plant, belt conveying systems, a temporary stockpiling system, trucking loading and transportation system, moisture-conditioning facilities (spreading and airing), and final disposal facilities (compacting). Due to the stickiness of the filtered tailings that governs the belt conveying system design, the operating moisture range must be established. Besides, proper technical aspects such as planning, executing, and analysing both the laboratory and the pilot testing data to validate process design parameters; selecting filters; defining spare filtering capacity; handling the out-of-range filtrated moisture; sizing the belt conveying system; configuring the equipment involved, must be considered.

Nov 8, 2021

Rope guides, consisting of ropes spanning between anchor points at the top and bottom of shafts, have frequently been considered as a viable alternative to fixed guides, comprising buntons and guides. However, their design has generally been based on empirically derived rules, arising from European hoisting practice of 50 to 100 years ago. This paper describes a recent technology development project aimed at defining and quantifying the important forces acting on rope guided conveyances, calculating the resulting displacement of the conveyances and assessing whether the displacements are acceptable or not. The paper describes the derivation of aerodynamic force coefficients based on CFD analyses and other significant forces acting on the conveyance and rope system. The conveyance displacements may be calculated using computer simulation of the mechanical system, or approximately using simplified equations given in the paper. Measurements taken to confirm the suitability of the proposed formulation are described. The combination of displacements and assessment of the rope guide system design are proposed, based on the ratio of design clearances and the predicted displacements.

Jan 1, 2005

By G K. N Subasinghe

Metallurgists operating Knelson Concentrators (KC) often rely on manufacturerÆs recommendations for selecting operating parameters, such as fluidising water flow rate and cycle time. Recent studies have shown that these parameters are not only dependent on the machine parameters but also on the feed characteristics, such as size distribution of the gold and gangue particles and the composition of its constituent minerals. It is known that a particle entering a KC initially traverses a circular path within the bowl. For a particle to maintain a given orbit, the required centripetal force must be supplied by external means. It has been argued that this centripetal force, which is dependent on the mass of the particle, its radial position and the rotational speed of the bowl, is provided by the fluid drag force created by inwardly moving fluidising water and the BagnoldÆs force created by the particle/particle collisions. Depending on the fluidising water flow rate, one of two situations can occur where the porosity of the bed increases or decreases, which influences the amount of material retained within the bowl. The amount of material of a given size and density retained in the bowl is thus dependent on the extent of the centripetal force provided. Based on the above concept, a criterion that can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It may also be construed that this criterion demarcates the transition of the bed from a packed-bed state to a fluidised state. By identifying the transition values for the different constituent mineral particles in the feed, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. In addition, the kinetics of gangue displacement by incoming heavy mineral particles were also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build-up of heavy mineral reaches a maximum. A model has been proposed to predict the optimal batch cycle time for a KC in terms of the feed characteristics and machine operating parameters.

Jan 1, 2006

By H W. Wu

Occupational exposure limits for diesel particular matter (DPM) are progressively being adopted in a number of countries. Many of these follow the lead of the US Mine Safety and Health Administration initiated in 2008. In line with adoption of best practice it is accepted that all exposures should be reduced to as low as reasonably achievable. The management of diesel emissions and occupational exposures to those emissions requires an integrated strategy incorporating efforts from all key departments on a mine, including management, production, maintenance, supply and occupational health and safety.Australian coalmine longwall moves rely on the use of high-powered diesel equipment such as chariots and other machines that produce exhaust pollutants of gases and DPM. To reduce mine personnel’s exposure levels to DPM a hierarchy of controls can be followed. Minimising the use of diesel equipment, better operator positioning in relation to exposure source, using efficient engineering methods and adopting better ventilation to reduce concentrations through dilution are some of the controls that can eliminate exposures. Approaches generally adopted in Australian longwall mines currently rely on a combination of strategies such as optimisation of ventilation, use of diesel particulate filters and use of diesel tag boards that minimise the number of vehicles through recording entry and exit into working panels.A study has been undertaken into the mine ventilation systems currently in use during longwall moves within Australian modern longwall extraction mines. This paper reviews current longwall section ventilation systems and discusses evolving changes being adopted to address the more complex problems in dealing with section DPM during phases of the operational moves. The effects of DPM on crew members as well as the diesel equipment operators within a longwall section are examined. Issues that should be considered in designing the longwall section ventilation during the moves are discussed.CITATION:Wu, H W and Gillies, A D S, 2015. Review of ventilation optimisation strategies during longwall moves, in Proceedings The Australian Mine Ventilation Conference, pp 133–140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J Seppelt, B Akerstrom, J Bubnich, D Seaman, T Waters

The Cadia Hill concentrator at Newcrest’s Cadia Operations has undergone several modifications and upgrades to treat an increased throughput rate of harder ore from the Cadia East block cave mine.Subsequent to the commissioning of the expanded circuit, the flotation cleaner block has undergone a systematic optimisation programme tackling all facets of circuit operation. This included debottlenecking circuit constraints and installation of Jameson cell technology to enhance copper and gold recovery while rejecting fluorine and gangue from the concentrate.This paper outlines the improvements over the course of the project and results obtained from the implemented actions.CITATION:Akerstrom, B, Seppelt, J, Waters, T, Bubnich, J and Seaman, D, 2018. Cleaner circuit optimisation at Cadia Operations, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 457–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By T Huynh, K Tungpalan, E Wightman, M Edraki, S Palaniandy

Most preventive environmental management practices promote proactive integrated approaches to waste management. For example, life cycle assessment is often used to find the ‘hot spots’ of environmental burdens. This kind of approach is often based on generic data and has rarely been used for tailings. Besides, life cycle assessments are less useful for designing operations or simulating changes in the process and consequent environmental outcomes. It is evident that an integrated approach for tailings research linked to better processing options is needed.The aim of this Nextmine™ project is to develop new tailings management models by streamlining orebody characterisation, process optimisation and rehabilitation. We present an integrated tailings management approach and preliminary results from a case study. Combined grinding and flotation models were developed using geometallurgical data from the orebody, to predict the properties of tailings produced under various processing conditions. The modelling scenarios based on the case study data provide the capacity to predict the composition of tailings and the resulting environmental management implications. For example, the type and content of clay minerals in tailings will affect the geotechnical stability and water recovery. Clay content will also influence decisions made for paste or thickened tailings and underground backfilling.CITATION:Edraki, M, Huynh, T, Wightman, E, Tungpalan, K and Palaniandy, S, 2015. An integrated approach to proactive tailings management, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By I Basson, J A. Miller, M Becker, F C. de Beer, L C. Bam

"Geometallurgy brings together geologists, mine planners and process engineers to extract meaningful mineralogical and textural information from an orebody, with a view to predicting its metallurgical response. Preferably, automated analytical techniques, which provide mineralogical and textural information, should process a large number of samples quickly, relatively inexpensively and reliably. Microfocus X-ray computed tomography (µXCT) is capable of producing 3D volumetric information on texture and mineralogy that satisfies some of these criteria. µXCT has been used extensively to study the porosity and internal pore structure of iron ore pellets as part of downstream processing. It has not been widely applied to earlier mineralogical and textural analysis of unprocessed ore, due to the limited ability of X-rays to penetrate high-density samples. In this contribution, we propose scanning methods to overcome this limitation, thereby facilitating a broader application of µXCT to iron ore resource management.CITATION:Bam, L C, Miller, J A, Becker, M, De Beer, F C and Basson, I, 2016. X-ray Computed Tomography – Determination of Rapid Scanning Parameters for Geometallurgical Analysis of Iron Ore, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 209–220 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By S Girard, L Rowland, V Lawson, Y Shields

Since 1948, ValeÆs Matte Separation Plant has been successfully using magnetic separation and froth flotation to separate the copper sulfide, nickel sulfide and Ni-Cu metallic alloy contained in Bessemer matte for downstream processing. Though some equipment upgrades have been performed over the years, the flow sheet has generally remained unchanged since the early 1970s. The need to improve metallurgical performance led to the trial of a scalping flotation column to produce a final copper concentrate ahead of the cleaner circuit feed to take advantage of a high degree of copper mineral liberation, reduce cleaner-recleaner circulating loads and decrease the associated loss of selectivity. Plant results indicated that 50 per cent of copper contained in the rougher concentrate could be recovered at final grade target. Results indicate that up to a 1.5 per cent increase in copper recovery to copper concentrate was achieved during the scalper trial due to a reduction in the generation of fine chalcocite which has historically been observed to report to flotation tailings due to surface contamination. Deficiencies are currently being addressed and a long-term trial is scheduled to confirm the benefits of copper scalping.CITATION:Girard, S, Rowland, L, Shields, Y and Lawson, V, 2012. Copper scalping at ValeÆs matte separation plant, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 299-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By J L. Stacey

The diverse priorities, drivers and concerns of multiple stakeholders in the minerals industry complicate the integration of sustainable development considerations into mine design, as well as operational and strategic decisions. The ability of the industry to address all role-playersÆ needs, or indeed, to achieve consensus among all role players on the plethora of sustainable development issues seems a noble yet unattainable goal. One of the difficulties in assessing the relative importance of sustainable development issues across many stakeholders is the inevitable lack of impartiality in valuing these issues. Starting from a premise that transparency and fairness of the process are absolute prerequisites for progress, but that consensus is not, an approach has been developed in which all stakeholders are asked to assess the importance of all other stakeholdersÆ priorities, excluding their own. The approach recognises that stakeholders have different levels of contribution, understanding, vested interests, and perceptions of legitimacy and entitlement, across the diversity of sustainable development issues and decision criteria. Using Triangular Value Analysis, the relative weightings of each of the stakeholderÆs priorities are determined through a regression-like technique. The uniqueness of this approach is the manner in which self-assessment bias and overemphasis of stakeholdersÆ own priorities are avoided. The methodology can be used for both internal and external stakeholders, and in conjunction with other group decision making techniques, such as the nominal group or Delphi techniques. This paper will illustrate how Triangular Value Analysis may be applied in the minerals industry to determine priorities in various decisions relating to potentially conflicting sustainable development priorities within the industry.

Jan 1, 2009

By J T. Woodcock

This paper discusses characterisation techniques that can be applied to complex waste products from metal production and processing operations with the aim of devising treatment methods for upgrading the metal content for recycling. Two waste streams were selected to illustrate the role of characterisation in adapting mineral processing techniques to provide an effective recycling strategy. Waste products chosen were:aluminium dross, which contains metallic aluminium particles in a coarse matrix of many components; and steel shredder sludge that contains copper wire and other metallics in a matrix of plastic and natural fibres, iron oxides, metallic iron, and other compounds. Characterisation methods discussed include chemical analysis (XRF, ICP-AES, and selected specialised techniques), phase analysis (XRD, SEM, TEM, and optical microscopy), morphology (IFESEM), sizing analysis (screening, Cyclosizing, Infrasizing, Malvern sizing), and general techniques such as particle shape, surface area, and porosity determinations. The applicability of these techniques to the waste products is considered in relation to their advantages and disadvantages, and sampling issues.Treatment techniques considered for the two waste products included comminution, screening, air or water classification, simple water leaching, gravity separation, magnetic separation, flotation, and eddy current separation.Tentative flow sheets were developed for the two wastes. For aluminium dross, it was proposed to use fine crushing followed by water washing to remove soluble chlorides and aluminium nitride, and then desliming followed by flotation of the granular fraction to give a metallic aluminium-rich concentrate. For shredder sludge, it was proposed to use wet screening, water classification, and gravity concentration to produce a copper-rich product and magnetic separation to produce a metallic iron-rich product.

Jan 1, 2004

By A J. Weston

Block or panel caving technology is far removed from that of the top slicing and block caving of the late nineteenth or early twentieth centuries. The rapid mechanisation and expansion of these methods in the late twentieth century was as much a result of the change of the technology of the unit operations of development, ground support, drilling and blasting and transport as it was of the advances in geotechnical understanding and practice. The small footprint gravity and scraper block caving mines with boundary weakening, rail transport and shaft hoisting of the early to mid-twentieth century have been replaced by massive high lift panel caves using preconditioning of the ore, large load-haul-dump units, adjacent crushers and conveyors to surface. The technology changes in the unit operations are described and the drivers for these changes examined.CITATION:Weston, A J, 2016. The evolution of block caving technology, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 265–274 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By E Mielczarski

Determination of the adsorbed layer composition and structure at molecular and atomic levels and understanding adsorption mechanisms and dynamics are vitally important for the preparation of surface layers with specific functions. Direct information, at a molecular level, about mineral surface composition, its structure and surface distribution is crucial to perform an efficient separation process for mineral beneficiation. This information is equally important for modifying surface properties of industrial minerals for specific applications such as: fillers, composites, weathering resistance, etc. An understanding of the mechanisms and kinetics of the interaction of first adsorbed organic molecules with mineral surfaces is a fundamental requirement for the prediction and control of the macroscopic surface properties governing the efficiency of separation technologies or new material formulations. The developed infrared external reflection technique has a unique ability to study interface phenomena, at a molecular level, on heterogeneous substrates. The variety, precision and reliability of information about the interface phenomena delivered by this technique is superior to any other single technique. The experiments are fast and non-destructive. High sensitivity (starting from 20 per cent of the monolayer) in situ collected information in a multiphase system, even in the region of strong absorption of the substrate, makes this technique a very valuable experimental tool. The complexity of the recorded reflection spectra, their sensitivity to variations of the optical properties of all bulk and surface components and their spatial distribution in the system under investigation, are in fact the major strengths of this technique. A few examples of the application of this multi-diagnostic technique, for monitoring surface modifications of semi-soluble minerals for selective flotation, will be discussed in detail in this paper.

Jan 1, 2005