Search Documents

By Palmer DJ

Mercury is introduced into EZ's electroly tic zinc/sulphuric acid plant complex at Risdon, Tasmania, in zinc sulphide concentrate. Mercury is volatilised during the roasting operation and then distributed in the sulphuric acid plant effluents and product acid. Following an investigation of the factors determining the mercury distribution, a plan was formulated to-provide an environmentally accep- table degree of mercury containment at Risdon. This paper discusses details of the various control measures investigated and out- lines the reasons for selecting the particular procedures finally adopted for the Risdon plant.

Jan 1, 1980

By D J. Williams, C Zhang, F E. Herrera Cabrera

Farming on bauxite residue using screw propelled equipment (SPE) has been commonly practised to accelerate dewatering and as it promotes consolidation and enhances storage capacity. However, it is unclear when and how often farming should be conducted during the transition of bauxite residue from slurry to dry solids and how deep each slurry deposition should be. To address this issue, three desiccation tanks were established in the laboratory to investigate how much farming could enhance the desiccation and consolidation of tailings. The cuboid tanks, of 350 mm in height and 300 mm in width and length and with an opening on the top, were placed on load cells to monitor the water loss during desiccation and were instrumented with moisture and suction sensors designed and developed at the University of Queensland to measure the water content profile of the residue. The bauxite residue, composed of silt-size particles with low plasticity, was hydraulically deposited in the tanks as a slurry at 27% solid content, resulting in 100 mm depth of solid material settling. Evaporation was enhanced by placing two identical electrical fans above the tanks. Two phases were conducted. In the first phase, the two tanks were left untouched for evaluating non farmed conditions and for calibrating sensors, while in the second phase, three tanks were subjected to atemporal farming using purpose-built screw propelled equipment. The experiment was terminated when the residue was completely desiccated. This paper reports on the instrumented tank set-up and the results obtained to date.

Jul 1, 2021

By S K. Panda, M A. Van Ende, S Chatterjee

Tata Steel Netherlands (TSN) aims to reduce its CO2 emissions by 35–40 per cent by 2030 and become CO2 neutral by 2045. A first step to reach these targets is via the utilisation of an Electric Arc Furnace (EAF), which will run on a mixture of high proportion of Direct Reduced Iron (DRI) and scrap. For an EAF operation, optimisation of slag chemistry is important to achieve the right mix of basicity (for refining especially dephosphorisation), foaming, volume (rate) and refractory life. Slag composition and rate can vary widely depending on the process variables like charge mix, charge composition, feeding rate, oxygen lancing, external carbon injection/addition, fluxing and refractory erosion/corrosion. Moreover, it is important to note that the slag composition and rate are ‘transient’ parameters and change throughout the heat. This makes all the dependent phenomena and/or outcomes transient as well. To describe all these effects simultaneously and be able to realistically simulate the EAF operations, a validated dynamic process model is important in the absence of real plant data. In this study, a validated dynamic EAF process model based on the concept of Effective Equilibrium Reaction Zone (EERZ) has been utilised to analyse the impact of high DRI industrial scale EAF operations on the transient slag characteristics – including slag volume (rate), composition, phases, solid fraction and viscosity. Simultaneously, the model is able to predict the impact on steel and offgas characteristics. Case studies were performed with 70 per cent DRI:30 per cent scrap mix considering both low and high-grade DRI. Both melting and refining aspects of the process including continuous feeding, arcing program, carbon addition, fluxing and oxy-lancing were considered.

Jun 19, 2024

By S Nkwanyana, I Govender

Batch experiments in a 0.6 m diameter mill have shown that improvements of about 13 per cent in the efficiency of energy utilisation can be realised in ball mills by replacing 25 per cent of the ball charge by an equivalent volume of cost-free critical size pebbles from AG/SAG mills. For a mill of a given size, speed and charge filling, the rate of size reduction of ore particles depends on (i) the frequency of grinding media collisions (ii) the probability of capture of ore particles between the colliding grinding media (iii) the probability of fracture of the captured particles. The probability of fracture depends on the magnitude of collision energy. The distribution of collision energy into shear and impact events determines the relative strengths of attrition breakage and impact breakage. The efficiency of energy utilisation depends on which of the two mechanisms of breakage is more desirable in a particular milling stage. In this paper collision data from a series of DEM simulations of a mill charged with steel media and a mixture of steel media and pebbles is presented in energy spectra and spatial distribution maps. The data provides the necessary detail to elucidate the improvements in the efficiency of energy utilisation in ball mills when using a mixture of pebbles and steel media.

Aug 24, 2022

By S J. Kim, S W. Kim, L Tomas da Rocha, S Jung

Al2O3 has been regarded as a harmful gangue component in iron ore, especially causing reduction degradation in industrial sintering of iron ore. The current study aimed to utilise low-grade iron ore containing high Al2O3 content in sintering process. In order to counteract the adverse effect of Al2O3 on reduction behaviour of iron ore sinter, mill-scale and calcined dolomite were chosen as FeO- and MgO-bearing materials. Firstly, mill-scale was added to high Al2O3 sinter and addition was optimised as 10 wt per cent, then calcined dolomite was added further. Magnetite and magnesio-ferrite were identified as the major phases in iron ore sinter when adding mill-scale and calcined dolomite. As the dosage of calcined dolomite increased beyond 4 wt per cent of in sinter mix, unreacted MgO particles were observed, which is ascribed to the limitation of MgO dissolution into magnetite matrix. Both mill-scale and calcined dolomite were effective in improving compressive load and Reduction Disintegration Index (RDI) of iron ore sinter although its reduction degree was highly decreased. The addition of both FeO and MgO-bearing materials to high Al2O3 sinter has a potential to improve the sinter quality, also contribute to the recycling of industrial by-product. However, the amount should be optimised in views of phase development and deterioration of reducibility.

Jun 19, 2024

By X Tian, J Forster, A Olmsted, E R. Bobicki, M Goldbaum, D Boucher, C A. Pickles

As the global demand for metal values expands, it becomes increasingly important to create more sustainable mining operations. Consequently, considerable research and technology development is required to produce processes which are both more energy efficient and have a minimal environmental impact. One potential technology is the utilisation of microwave pre-treatment to reduce the energy requirements in comminution. Microwaves can preferentially heat the valuable mineral phases in an ore and the resulting differential thermal expansion leads to the formation of microfractures along the grain boundaries. As a result of the preferential heating, ore competency is reduced, mineral liberation is enhanced, a coarser grind size can be employed, and plant throughput can be increased. Furthermore, microwave pre-treatment can be combined with advanced ore sorting, to decrease the quantity of gangue material processed downstream and hence reduce tailings production. Previous studies on the microwave treatment of ores over the last 30 years have mainly been limited to low power bench-scale studies and there is a paucity of information on pilot and/or commercial scale studies. In the present research, the microwave heating behaviours of over 40 ores have been studied at the bench-scale. These results were used to generate a database, from which a unique classification system was developed. This system was used to rank the amenability of any given ore for microwave pre-treatment. This knowledge can be employed to predict the performance of the ores in the high-power pilot scale tests and thus can be used as a pre-screening tool. The effects of high-power microwave pre-treatment on grindability and liberation were reported. Additionally, the ore sorting potential was evaluated using a combination of X-ray transmission (XRT) and microwave infrared (MW/IR).

Aug 24, 2022

By K Verbeken, D Seveno, A Maslov, I Bellemans

Recycling and decarbonisation current metallurgical processes is key for our planet’s future and in both cases, digital twinning will play an important role. However, the various modelling techniques being used for digital twinning require a lot of input values on variables such as viscosities, diffusion coefficients and surface energies that need to be known as a function of temperature, atmosphere and composition, but which are not widely available, such as in databases, for molten slag phases. The need for more accurate data on physical slag properties is clear and will be extremely relevant for making more realistic and quantitative simulations. Some of these properties are difficult to determine, which is inherent to the very high pyrometallurgical temperatures. Therefore, this work focuses on some aspects related to determining electrical conductivities, viscosities and surface tensions of slags via a combined experimental-modelling method. Besides experimental work, molecular dynamics (MD) simulations can be used to investigate oxidic slag physical properties. With MD simulations, one can follow the time evolution of a system (consisting of atoms or molecules) by integrating Newton’s equation of motion. The input for an MD simulation mainly consists of a force field as well as initial positions, velocities and mass of each atom. The determination of the transport properties in existing literature of MD simulations in oxidic systems, is typically based on incorrect assumptions. For example, to determine the ionic conductivity, the frequently-used Einstein-Stokes equation fails to take into account all ionic types and neglects correlated motion. Furthermore, the viscosity determination via the Einstein-Stokes formula also assumes independent motion of the different ions. This paper gives a brief overview of the opportunities and challenges related to the use of MD simulations for oxidic slag systems.

Jun 19, 2024

By D Clarke, I Minniakhmetov

The Olympic Dam deposit is truly a world-class IOCG-Ag deposit, the world’s fourth largest deposit of copper and the world’s largest known single uranium deposit. Traditional and non-traditional methods have been used to accurately model the geology and mineralisation of the Olympic Dam deposit. Conditional simulation models have long been used as the most robust method for estimating risk and uncertainty in mine planning decisions at other mines around Australia and the world. There are many challenges associated with simulating the Olympic Dam deposit at a selective mining unit size sufficient for underground mine planning purposes. These include the size of the deposit, resulting in hundreds of millions of grid blocks; the disseminated nature of the zoned sulfide mineralisation. And lastly the direct relationship of the relative abundances of the sulfide mineral species that are crucial to the Olympic Dam smelter performance. Several geostatistical techniques have been utilised in the workflow for the Olympic Dam Conditional Simulation model to address these challenges. The key techniques are: • Projection Pursuit Multivariate Transform to de-correlate the main elements before simulation. • Pluri-Gaussian implicit boundary simulation method to simulate the mineralisation domains. • Spectral simulation method of de-trended and de-correlated attributes with account of local varying variance. The resulting conditional simulation models have been validated against histograms, grade-tonnage curves, cross-plots and assessed for variogram reproduction. This paper presents how the final conditional simulation models compare to benchmarking models created using alternate estimation techniques of ordinary kriging and local uniform conditioning. It also presents a validation process using historical samples to test final estimate accuracy of the simulation models.

May 24, 2023

By P Revell, G Wilkie, P Walters, L Keeney, F Faramarzi

Grade Engineering® is a value-driven strategy aiming to maximise benefits by exploiting intrinsic grade variability of ore deposits. It utilises a multitude of separation techniques to remove low grade material before being introduced to post-blast size reduction processes, i.e. crushing and grinding. At an operational scale, Grade Engineering® techniques can be implemented at the drill-and-blast stage, to control the degree of fragmentation in accordance with the spatial distribution of valuable minerals across an ore domain through differential blasting. It can also exploit intrinsic textural and breakage characteristics of a given ore type to reject uneconomical barren material at coarse sizes, which is known as Natural Deportment. Grade Engineering® can also be employed in the deliver stage of the mining value chain through sensor-based bulk and particle sorting. Each strategy is therefore highly dependent on the responsiveness of an orebody to available techniques. That is, the extent to which Grade Engineering® drivers would be capable of unlocking potential values of currently un-amenable orebodies depends on how detailed the heterogeneous nature of ore domains can be described. This paper considers exploring possible linkages between deportment characteristics of an ore and its competence when broken in a range of energy inputs at a particlebased level. Accordingly, potential opportunity may lie in exploring whether the intensity of input energy (or degree of fineness) can be used as a lever to improve or ‘unlock’ ore amenability to Grade Engineering® techniques. Implications from such a detailed approach offers new opportunities to enhance Grade Engineering® gains through engineering ore competence variability.

Nov 10, 2020

By J Rutter, J du Plessis, er, M Scott, D Alex

It is generally acknowledged that bulk ore sorting is an attractive prospect for the mining industry. However, uncertainties relating to the operational performance of sensor technologies, the grade heterogeneity present in analysed material and the physical separation performance of the coupled system complicate the evaluation and deployment of bulk ore sorting strategies at operations. To assist in the quantification of these uncertainties, the Cooperative Research Centre for Optimising Resource Extraction (CRC ORE) and Anglo American have implemented a systematic methodology to evaluate the deployment of sensor technologies for bulk ore sorting. This methodology was implemented at a bulk ore sorting demonstration plant using penetrative prompt gamma neutron activation analysis (PGNAA) and surface x-ray fluorescence (XRF) measurements of base metals, as a proxy for precious metals, at Mogalakwena PGE Mine. The methodology comprises of three phases. The initial phase involves the preliminary investigation of sensor technologies and analysis to reduce identified risks prior to commissioning of the bulk ore sorting plant. The second phase executes a series of experiments to prove the sensing technologies in the operational environment and provide confidence the sensors can drive separation. The final phase demonstrates the production scale bulk ore sorting performance of the plant and validates its performance by campaign of the sorted products at the processing plant. Throughout the operational deployment and evaluation of bulk ore sorting at Mogalakwena, several key lessons were learned. These learnings relate to the calibration requirements of the sensor technologies, the application of surface vs penetrative sensor techniques and the preservation of grade heterogeneity delivered to the sensors. This paper presents the methodology used, and lessons learned, in the operational deployment and evaluation of PGNAA and XRF sensors for bulk ore sorting at Mogalakwena PGE Mine.

Nov 10, 2020

By I M. Platten, C J. S Sangster, Y Xie

The Cononish gold-silver deposit is a steep, relatively narrow quartz-vein system, with a current total mineral resource of 154 000 oz Au and 589 000 oz Ag. The northeast-southwest trending system was emplaced into late Proterozoic metasediments, and postdates metamorphism and associated Caledonian Orogenic foliations. Assay and mineralogical data show that gold and silver is spatially associated with sulfides in quartz. The main sulfide is pyrite, but galena, chalcopyrite and sphalerite occur in small amounts. Gold occurs as electrum, with minor native gold, and silver occurs additionally as tellurides and native metal. The gold/electrum is fine-grained, generally less than 100 microns in size. The main ore shoots plunge 45¦ south-west, have a 40 m to 80 m intersection with the existing underground development and extend between 40 m and 260 m down plunge. Small-scale sulfide-bearing domains within the vein carry the highest gold grades. They collectively define the ore shoots, where one or two, and rarely three, of the domains are present at an individual site in the vein. Discontinuity of individual domains, variation in domain thickness and internal heterogeneity results in short scale variation in grade across the structure. Geological mapping along a 1.2 km exploration adit has provided critical æconditioningÆ data to support resource evaluation based on development and relatively wide spaced drilling. In addition, it has provided an indication of potential challenges that could be encountered during production.

Jan 1, 2009

By S Robinson, A Turner, R Dale, C Butler

"Sandfire Resources NL- (‘Sandfire’) DeGrussa definitive feasibility study (DFS) identified geometallurgy as a major factor in achieving optimum plant performance at the DeGrussa mine. A geometallurgical initiative was created to proactively investigate this issue, and a key initial achievement was the 2013 paper by Condon et al (2013) on developing a working geometallurgical model from first principles. Significant advancements in Sandfire’s geometallurgical understanding since that publication now shape how information is presented and communicated.The main geometallurgical parameters so far identified as critical factors affecting plant performance are Cu:S ratio, iron sulfide mineralogy, talc carbonate content and sphalerite content. Apart from specific mill strategies, geometallurgical issues have been managed through communication between departments and strategic run-of-mine (ROM) pad management.This paper uses the current theories of geological evolution of the volcanogenic massive sulfide (VMS) deposit at DeGrussa, to discuss the variability between the orebodies C1, DeGrussa (sea floor mounds) and C4, C5 (sub-sea floor replacement) to highlight the different issues each orebody is expected to encounter when processing.A zone of altered low-grade mineralisation surrounds the main orebodies at DeGrussa, referred to as a halo. Talc minerals are often patchy within this halo and often cause significant recovery issues during processing. This halo has been successfully modelled using MgO as a proxy. The ability to model the talc material assists with both identifying potentially problematic zones for processing and geological interpretation of the ore deposits evolution.Early in geometallurgy studies at DeGrussa it became apparent that it would be useful to identify processing performance prior to mining. This necessitated the incorporation of specific sulfide species into the mining block model. These attributes are interpolated from the logged sulfide estimates allowing a clear picture of the abundance of each mineral type within a defined area.In conjunction with the block model a geometallurgical factor (GMF) graph was developed, identifying sulfide mineralogy based upon mineral assays. These two recent additions to the model provide a clear picture of the nature of the ore sources that will be presented to the processing plant.The future of geometallurgy at DeGrussa will see these tools used to aid mine scheduling with a view to further improve processing recoveries.CITATION:Butler, C, Dale, R, Robinson, S and Turner, A, 2016. Geometallurgy – Bridging the Gap between Mine and Mill: a Case Study of the DeGrussa Geometallurgy Program, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 77–88 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By F Clark, J T. Carswell

Ore definition for final stope planning is often a challenging prospect in underground (UG) gold mines which exhibit high geological and grade variability. Unlike the grade control (GC) scenario in an open pit (OP), the ability for the mining geologist to plan a sampling campaign which effectively characterises the underlying mineralisation is fraught with difficulty. UG sampling patterns are strongly clustered and typically not dense enough to characterise the spatial and statistical properties. Very commonly, sample volumes are not large enough to provide a reliable grade estimate of the surrounding rock. These factors critically affect our ability to accurately map out ore positions and estimate metal quantities.At Sunrise Dam, traditional UG sampling and modelling techniques have proven to be an unreliable strategy for successful stope planning and extraction. The problem was first observed during the final cut-back in the open pit for which the mineral resource model was constructed from UG diamond drilling. Open Pit grade control reconciliations were strongly positive for both tonnage and grade compared to the resource model. Underground workings missed significant quantities of ore which was laterally defined by open pit reverse circulation (RC) GC drilling. Upon examination it was realised that the cause of the problem was one of inadequate sample density and sample support, the implications of which potentially affected the entire UG mine.As part of a broader study into underground grade control procedures, detailed reconciliation of initial stope production from the GQ domain also pointed to inadequate sampling as a major constraint to effective grade control and reserve conversion.To overcome this deficiency, dense 115 mm wet RC grade control drilling and conditional simulation modelling has been successfully implemented with the intent to replicate the grade control process in the open pit. The increase in sample density and sample volume has proven to be a very effective tool for mapping out highly complex mineralisation. A marked improvement in stope definition, reserve conversion and Mine to Mill reconciliations has been demonstrated on the back of an innovative approach to UG grade control.CITATION:Clark, F and Carswell, J T, 2014. Using reverse circulation drilling to improve sampling in a complex underground gold operation – an innovative approach to underground grade control at the Sunrise Dam Mine, Western Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 143–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By A J. Ryan

The Ernest Henry copper-gold Mineral Resource is the major asset heldby Ernest Henry Mining Pty Ltd, comprising A$6.4 billion of containedmetal. The case history presented below describing the evolution andevaluation of this resource generally observes best industry practice and is a good example of effective due diligence in the resource delineation and estimation process. Early reconciliation data from mine production confirms the accuracy and validity of the resource estimate, providing valuable assurance to the mine owners.

Jan 1, 1998

By S Coward, C Xu, P A. Dowd

"This paper provides an assessment of the current challenges in strategic mine planning and design and suggested approaches for addressing them. The specific challenges covered are: realistic quantification of downstream processes applied to orebody models to provide an integrated approach to mine design and optimisation modelling, estimation and simulation of geometallurgical variables and their integration into resource and reserve estimation and mine planning modelling, estimation and simulation of new variables for new forms of mining – deep mining, particularly block caving, and solution mining flexibility in planning and design to manage risk and minimise its impact information technology (IT) infrastructure and platforms for rapid online data collection, storage, access and processing.Most of these challenges require new types of data, variables, modelling and estimation methods. Foremost among the new types of variables and data are geometallurgical and dynamic rock mass characterisation variables. New types of data and data collection include rapid generation of very large amounts of online sensor data and the consequent need for rapid processing and modelling of these data.This paper outlines the challenges and strategies in each of these areas and uses examples of models and outputs to illustrate approaches and potential solutions.CITATION:Dowd, P A, Xu, C and Coward, S, 2014. Strategies for mine planning and design, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 41–50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By J-P Franzidis

A technique for determining the recovery of attached particles across the froth phase in flotation that relies on measuring the rate at which bubble-particle aggregates enter the froth is used to investigate the selectivity of attached particles across the froth phase. Combining these measurements with those of other techniques for determining the froth recovery of attached particles provides an insight into the different subprocesses of particle rejection in the froth phase. The results of experiments conducted in a 3 m3 Outokumpu tank cell show that the detachment of particles from aggregates in the froth phase occurs largely at the pulp-froth interface. In particular it is shown that the pulp-froth interface selectively detaches particles from aggregates according to their physical attributes.

Jan 1, 2005

By D R. Seaman, Y Peng, F Burns, D J. Bradshaw

Telfer Gold Mine is a gold-copper mine in the eastern Pilbara of Western Australia, owned and operated by Newcrest Mining Limited. TelferÆs ores are processed by a dual train, 21 Mt/a, concentrator where gold is primarily recovered by gravity concentration and the flotation of a gold-bearing copper concentrate. A minor portion of TelferÆs gold is also recovered to a pyrite concentrate that undergoes treatment via carbon-in-leach (CIL) cyanidation. The gold recovery of the CIL circuit is below the industry standard and operates with a high reagent consumption rate.With a new fine-grinding facility, the Telfer process plant will have the ability to liberate copper and gold from the pyrite concentrate and recover these by flotation prior to the existing leaching circuit. This process will improve overall gold and copper extraction, while reducing reagent consumption in the CIL circuit.This article is an overview of the development of this methodology. Size-by-size analysis and mineralogical studies of monthly composites identified factors limiting the CIL gold recovery and the causes of high reagent consumption. Laboratory studies confirmed a relationship between the regrind product size and gold leach recovery. The addition of an intermediate flotation stage ensured that the regrind circuit will improve overall recovery while at the same time reducing operating costs. Without the addition of a flotation stage, the additional reagent consumption from regrinding alone would be prohibitive towards increasing recovery. Pilot scale studies confirmed the conditions required to selectively recover gold and copper from the pyrite concentrate as well as establishing the full scale regrinding energy requirements. Construction of this facility at Telfer is currently underway.CITATION:Burns, F, Seaman, D R, Peng, Y and Bradshaw, D J, 2012. Development of a pyrite regrind circuit at Telfer Gold Mine, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 45-52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By P Joyce, D R. Cooke

The Dinkidi Cu-Au porphyry deposit is situated in the Caraballo Range of North Luzon, Philippines. Although comparatively small, Dinkidi has unusually high gold grades with drilling by Climax-Arimco Mining Corporation delineating a 110 Mt orebody at 1.2 g/t gold and 0.5 per cent copper. The magmatic-hydrothermal evolution of Dinkidi records a distinctive switch in mineralisation from an early orthoclase-dominated Au-rich assemblage, typical of alkaline porphyry systems, to a later quartz stockwork Au-Cu rich assemblage typical of most calc-alkaline to shoshonitic porphyry systems. The early orthoclase-dominated stage is associated with the intrusion and crystallisation of a variably-textured clinopyroxene-syenite dyke that contains high-grade (5 - 20 g/t) gold mineralisation. We consider this dyke to be a Cu-Au porphyry analogue to the pegmatites found in granitic systems. Dinkidi is hosted within the Early Miocene Didipio Igneous Complex. This alkaline igneous complex is comprised of early unmineralised gabbros (pyroxene-plagioclase cumulates), clinopyroxenites (pyroxene cummulates), diorites and monzodiorites that have been intruded by a large, weakly mineralised monzonite pluton. The Dinkidi deposit is located at the southern margin of the monzonite pluton. Mineralisation is hosted within a composite monzonite stock. Within the stock, an 800 metres by ~200 metres (plan section) elongate monzonite stock (Tunja Monzonite) predates and hosts the bulk of the Au-Cu mineralisation. This has been intruded by the thin (10 to 30 m wide), highly mineralised variably-textured magnetite- and clinopyroxene- phyric syenite pegmatite (the Balut Dyke). The youngest phases of the composite stock are leucocratic quartz-monzonite porphyry (Quan Porphyry) that grades texturally, in its core, into a post-mineralisation crystal-crowded quartz-syenite (Bufu Felsite). The late-stage Bufu Felsite is inferred to be the source of much of the Cu-Au mineralisation. The Didipio Igneous Complex has intruded a sequence of Late Oligocene alkaline andesitic lavas and volcaniclastics and overlying potassic dacitic lavas. Whole rock geochemical analyses indicate that the intrusions and the potassic dacite lavas in the surrounding region are co-magmatic. Five main stages of hydrothermal activity are recorded at Dinkidi. An unmineralised K-silicate (biotite-magnetite) alteration assemblage formed during the intrusion of the Tunja Monzonite stock. The diorites surrounding the stock display intense selectively pervasive biotite and magnetite alteration and are cut by an extensive network of orthoclase veins and monzonite dykes. The orthoclase-dominated assemblages of Stage Two carry substantial high-grade Au mineralisation and are associated with the intrusion of the Balut Dyke. The emplacement of this unusual dyke is associated with emplacement of pegmatitic clinopyroxene-orthoclase-magnetite¦sulphide dykes, localised orthoclase flooding along the margins of the dyke, and subsequent emplacement of an extensive orthoclase-actinolite-bornite¦chalcopyrite-fluorite stock-work, and development of widespread selectively pervasive actinolite alteration. The main stage of Au-Cu mineralisation at Dinkidi is intimately associated with the intrusion and initial crystallisation of the leuco-monzonite porphyry (Quan Porphyry) and emplacement of a quartz stockwork followed by carbonate-sulphide deposition and intense vein-related sericite and carbonate alteration assemblages. The quartz stockwork formed synchronous with the deposition of the æBugoy QuartzoliteÆ, a very coarse grained mosaic of quartz-orthoclase-perthite along the walls and top of the crystallising intrusion. Stage 3 was terminated by crystallisation of the distinctively vuggy Bufu quartz-syenite phase in the core of the intrusive, with associated antiperthite veins, and the subsequent explosive brecciation of the roof of the intrusion, forming a quartz-fragment breccia from the Bugoy Quartzolite. Retrograde metasomatism during Stage Four was intimately associated with the emplacement of extensive, late-stage carbonate, silica and zeolite veins and widespread selectively pervasive carbonate alteration. The last hydrothermal stage at Dinkidi, Stage 5, is comprised of strong selectively pervasive clay alteration and is associated with fault-related brecciation of the Dinkidi stock.

Jan 1, 1999

By I Gray

This paper examines the practical limitations that affect the measurement of stress in rock. As most rock stress measurement is conducted through the invasive process of drilling a hole in a rock mass, the nature of the rock and its response to being drilled form the basis of the stress measurement process. The prime techniques to measure stress down a borehole are to conduct hydraulic fracturing and its variant hydrojacking, overcoring, and the examination of the borehole wall for breakout or tensile fracture. It is also possible in some circumstances to use the sonic velocity within the rock mass as an indicator of the stress situation. Other structural indicators of stress such as joints, faulting and intrusions are useful but may not reflect the current stress situation within the rock mass. The variability of stress within the rock mass also needs to be considered as it is quite unusual to have a monotonic stress situation throughout any rock mass. The outdated concept of measuring the far field stress in a few measurement for use in a numerical model is quite dangerous. It is essential to make multiple measurements and to generate an understanding of its distribution in some form of model before stress can sensibly be incorporated into underground design. CITATION:Gray, I, 2018. The practicalities of effective stress measurement in rock, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 360–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By S Dorrington, J Olsen, N Kinkaid

Several studies have been conducted on the economic analysis of mining near-Earth asteroids for resources for use in Earth orbit. While these studies use detailed economic figures of merit, they often use many invalid assumptions in the trajectory design. Factors such as the energy and propellant requirements are estimated with analytic methods, however, the stay-time at the asteroid and the spacing of repeated launch opportunities are not taken into account. The work outlined in this paper attempts to combine detailed trajectory design methods with newly defined economic figures of merit to improve the economic assessment of asteroid mining missions. The study focuses on asteroid 2014 EK24, a near-Earth asteroid with very Earth-similar orbital properties.CITATION:Dorrington, S, Kinkaid, N and Olsen, J, 2015. Trajectory design and economic analysis of asteroid mining missions to asteroid 2014 EK24, in Proceedings Third International Future Mining Conference, pp 281–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015