Search Documents

By J Tien, J Huang, N Haque, M O’Brien

Coal preparation is an integral part of producing coal for thermal powerplants and metallurgical processing plants. Coal processing plants use various unit processes to separate gangue and ash content from mineral coal, thus increasing the specific energy content.A flow sheet and a simulation model was established for a typical coal processing plant using Microsoft Excel. This model used the mass balance and split factors for run-of-mine (ROM) coal, tailings and water usage from a typical, generic coalmine.The common method of coal preparation initially involves several stages of crushing to reduce the size of coal. It is then sent to the processing plant for further washing. The typical method in Australia for coarse coal material processing is the use of dense medium cyclone (DMC) (Kininmonth and Baafi, 2009). Flotation cells are used for processing of fine coal. The fine products are utilised for coking coal only. In our case study, the intended coal product is for thermal powerplants. Therefore, the fine coal processing utilised spirals instead of flotation, which is typical for the industry.CITATION:Huang, J, Haque, N, O'Brien, M, O'Brien G and Tien, J, 2016. Development, simulation, economic and environmental evaluation of a coal processing flow sheet, in Proceedings Life-of-Mine 2016 Conference , pp 48–51 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By T W. C Stambolie

Coalmines, like any other mine, generally involve the classic three-staged approach to mining studies; namely concept, pre-feasibility study (PFS) and feasibility studies (Cusworth, 2012). Subsequent to these studies, and in instances parallel to these studies, the commitment to an environmental impact statement (EIS) is made in order to secure both state and federal development consent. In recent times, the sentiment to both mining and coal is changing whereby the traditional approaches to mine planning and economic evaluation is complicated by evolving environmental legislation, expectations and time frames. It is all too common to take shortcuts in the development of projects in order to create the perception of cost savings and expediting the delivery timeline. Atkins (2016) points out that: boards of so many small to mid-tier mining companies, and a few majors, focus on relentless project delivery too early in the project process, with so little time and effort applied to risk analysis and option development. Unforeseen risks can cost any timeline or budget far more than the effort required assessing and mitigating these. The ultimate risk to any feasible coal project is that of environmental approval and achieving development consent.CITATION:Stambolie, T W C, 2016. A black canvas – planning a greenfield coalmine in New South Wales, in Proceedings Life-of-Mine 2016 Conference , pp 31–35 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By D W. Stevens

Mechanical sampling provides a definitive value for the product sampled but the results are not instantaneous, meaning that decisions on process control can only be made hours after the sample is taken. Chemicals are added, tailings are sent to waste, stockyards are laid and the data for the decision-making is historical. Online analysers provide instantaneous information, allowing operators to make immediate and cost-saving decisions on the process. However, pending the specific online analysis application, there is a need for reference sampling for dynamic calibration/bias updating of the analysers so that they can deliver the desired precision and accuracy. What would be the economic justification for combining mechanical sampling with online analysis to reduce laboratory costs and provide immediate process control with certainty of accuracy? Approved sampling according to the Theory of Sampling, with immediate process control information.CITATION:Stevens, D W, 2014. Justification for integrating mechanical sampling with online analysis, in Proceedings Sampling 2014 , pp 135–138 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By N Meadows, M Rodriguez

A 200 000 tpa heap leach demonstration plant was approved by the Murrin Murrin Joint Venture (MMJV) in December 2005 and engineering commenced in January 2006. The demonstration plant will utilise stockpiled ore reject material (æscatsÆ) and extract nickel and cobalt. Limited production from the demonstration plant is expected by the end of 2006. The demonstration plant will enable the company to fully investigate and understand all associated technical issues over the next 12 to 18 months, including the potential to expand the heap leaching operation to a commercial scale. In parallel, the MMJV will continue a research and development program to improve and expand the application of its heap leaching technology.

Jan 1, 2006

Mining the Carpathia orebody at the Ardlethan tin mine in the late 1970s involved an innovative approach to underground mining which stretched the limits of drilling and blasting techniques. Holes of up to 95 m in length were drilled and blasted from the surface to extract an orebody which extended from 45 m to approximately 95 m below surface. This approach resulted in the elimination of an underground drilling sublevel, thus minimising the costs and hazards associated with underground drilling and blasting. Now, almost 30 years on, this method would probably still be the most appropriate choice.

Jan 1, 2008

By Rokot M

In a little over three years, Chevron Niugini has built up a team of relatively young, hard working men and women, mostly Papua New Guineans, who spend most of their working days out among people in the Southern Highlands and Gulf Provinces who are directly affected by the Kutubu Petroleum Development Project. These are Land and Community Relations officers, or LACROs. They take on a huge responsibility, not only representing Chevron but also being friend, advisor and negotiator, frequently dispensers of medicines, and agricultural advice and more. When things go well, others get the praise, when things go wrong, LACROs are the martyrs. Just as the geologists who locate the oil, the drillers who find it, the engineers who design the facilities, the construction gangs who build them, the landowners who claim it, and the Government who monitor it, so are the LACROs part of a team.

Jan 1, 1991

By A Atkins

Six recent case studies were selected based on the eight main causes of mine disasters (Table 1; Quinlan, 2014) and where credible information sources, such as Royal Commission Reports, Coronial Investigations and textbooks, were available. The six case studies are listed below. Details are available via this link or the conference PowerPoint accompanying this paper. 1. Beaconsfield, Tasmania – 2006 Fall of Ground/Seismic Event (Chandler, 2009; Melick, 2007; Wright, 2012). 2. Bingham Canyon, USA – 2013 Manefay Slide (Ross, 2017). 3. Bronzewing, WA – 2000 Hydraulic Fill Inrush (Hope, 2002). 4. Brumadinho and Samarco, Brazil – 2015 and 2019 Tailings Storage Facility (TSF) failures (Bowker, 2019; Darlington et al, 2019; Demajorovic, Lopes and Santiago, 2019; Morgenstern, 2016). 5. Northparkes, NSW – 1999 Cave Air-blast (Bailey, 2003; Hebblewhite, 2003). 6. Pike River, NZ – 2010 Methane Gas Explosion (Macfie, 2013; Panckhurst, Bell and Henry, 2012.

May 5, 2022

By J M. Menacho, L Zhang, A Hoadley, L Verdugo, B Etschmann, W Bruckard

Since the introduction of Lithium-Ion Batteries (LIBs) in 1991, the market for lithium-ion cells has been driven by the high demand for portable electronic devices and more recently for batteries for the electric car industry. It is expected to grow rapidly to reach 2600 GWh globally by 2030 (US Government, Office of Energy Efficiency and Renewable Energy, 2021). However, there is a desperate need to recycle LIBs to recover valuable cathode materials and graphite. For this reason, several physical and chemical recycling technologies have been proposed to recover these materials from spent batteries. Amongst these, froth flotation technology is a potential cost-effective technology for separation of the graphite fraction from the lithium oxide components due to the natural hydrophobicity of graphite and density difference between graphite and cathode materials (Folayan et al, 2021).

Aug 24, 2022

By F Faraj, M Pal, M Haest, M Bradshaw, H Lang, K Hume

MineSense Technologies Ltd. is revolutionising grade control at mining operations by installing ShovelSense® sensors on buckets that measure the grade of every load before it is dumped in the truck. This allows the mine to exploit grade variations at a resolution that was not available before, reducing the amount of ore loss to the waste stream and removing waste from material destined for processing. These changes dramatically improve the profitability and sustainability of mining operations. ShovelSense relies on X-ray fluorescence analysis of the rocks as they flow in the bucket and is integrated with fleet management to direct the trucks to the right destination. Lab simulations of ShovelSense measurements on porphyry copper ores show correlations between predictions and lab measurements at 0.98 r-squared with a coefficient of variation of 10 per cent. Visualisation of copper grade predictions in three dimensions shows a reasonable match with the dig plan, but with local changes in the ore-waste contact due to more accurate contact identification, related to blast movement and other mining factors. Correct delineation of these contacts ensures ore trucks are not sent to the waste dump and waste trucks are diverted from the crusher, creating enormous value for the operation and the environment.

Mar 22, 2022

By T A. J Hopper, S Mukkisa, K-O Ott, D Palmer

RIG Technologies has developed new technology that can successfully acquire high quality natural gamma ray (GR) and hole deviations, downhole while drilling, on reverse circulation drills. This technology survives the hostile downhole environment with shocks of between 400–2500 g for 7– 10 days at a time. The Logging While Drilling (LWD) service eliminates the need to run in-rod surveys, either by the driller or by wireline trucks and crews. This time saving is in the middle of the drilling process, thus enabling drills to keep drilling and increase their productivity. Additional to the natural GR and directional survey, the downhole tool is equipped with sensors to measure the downhole dynamic response of the drilling system providing insights into rock hardness, density and potentially clay types. These parameters have never been acquired behind the hammer before and coupled with surface measurements from the drills themselves, form a rich data set for trainable machine learning algorithms shortening the time to receive advanced geophysical answer products from sometimes months, to live feeds directly from drills (Hopper, 2019). Alive, high speed, two-way data link between surface data acquisition systems and downhole geophysics tools has been established and incorporates calibrated surface measurements of dynamic forces directly on the drill string to match up with those measured downhole. Receiving live streams of natural GR and hole deviation surveys as the drill is drilling allows true remote decisionmaking with live data available anywhere in the world. The combined data from surface and downhole dynamics builds a data set that could begin to enable true optimisation of autonomous drilling processes.

Nov 8, 2021

The Golden Cross mine is situated in a sensitive environmental setting on the North Island of New Zealand, about 150 kilometres south-east of Auckland and about 8 kilometres NW of Waihi. The mine is situated in dipping topography, with volcanic ashes making up soils, fault zones running through the area, and rainfall of about 3 m per year on average. Water management is the most demanding environmental challenge on site, and a comprehensive programme has been put in place to address tailings deposition, long term tailings storage, and water treatment during and after operations.   The tailings impoundment is built with an underdrainage system that collects groundwaters and waters that seep through the impoundment. The embankment and impoundment are both built to withstand the Maximum Credible Earthquake and the Probable Maximum Flood. Tailings are treated to remove cyanide and to decrease metal solubility to reduce long term risk to water quality after mining. A state-of-the-art water treatment plant is utilised to treat water from the underdrainage system and water decanted from the top of the tailings pond and stormwaters to remove residual cyanide and metals to extremely high standards with a great deal of reliability and at reasonable cost. Closure of the facility addresses long term post mining water quality issues, and rehabilitation of the area with wildlife habitat as a priority.

Jan 1, 1995

By P E. H Gregg, R B. Stewart

Reclamation field trials commenced in 1985, two years before the granting of the Mining Licence. The level of pasture production on varying soil depths (0 cm, 5 cm, 15 cm and 25 cm) overlying both tailings and oxidised waste overburden was assessed.   After seven years, the rate of increase of N, C, P and S, losses of Sand P and pH changes were investigated on the plots where grass seed was sown into bare tailings. It was determined that on these plots it would take approximately 24 years to reach the original carbon and nitrogen levels at the mine site. Further tailings trials have been initiated to investigate alternative land use options for the tailings dam. Growth increases of 73% occurred in native species growing directly in tailings, and growth increases of 78% occurred in tailings amended with compost over the first six months. Pasture trials on tailings with and without a compost amendment have also been initiated. Research has commenced to investigate the restoration options for acid producing pit slopes. The early field trials have been put into practice with the restoration of oxidised waste on the tailings embankment. This is progressive with approximately 16 ha restored to productive pasture at present. Yields compare well with those of the most versatile and productive soils types investigated in baseline studies of the area before the tailings dam was constructed.

Jan 1, 1995

By J Heyes, G A. Maddocks, R J. Stewart, G D. Corder

Mining is an international business and vital contributor to national and global economies. It depends on the trust and confidence of investors and stakeholders for its financial and operational well-being (Committee for Mineral Reserves International Reporting Standards (CRIRSCO), 2016). The Social Licence to Operate (SLTO) is an increasingly multifaceted and multistakeholder risk that can impact investment decisions. Community challenges to broader political and economic decisions have given rise to protest delaying or stopping projects or closing mines and has led to loss of life (Ernst and Young, 2016). Some governments are now giving greater powers to stakeholders to make the final decision on approving mining and metals activities (EY, 2016). With billions of dollars in project investment at stake, ongoing engagement, collaboration and effective communication with stakeholders is crucial and mutually beneficial solutions are increasingly expected (EY, 2016). It is therefore essential that the industry communicates the risks (and opportunities) associated with investment effectively and transparently in order to earn the necessary level of trust with investors and stakeholders to underpin its activities (CRIRSCO, 2016). Despite this need, investor and stakeholder trust in the sector has eroded in recent years.CITATION:Maddocks, G A, Corder, G D, Heyes, J and Stewart, R J, 2016. The social licence to operate and drivers for change – resource reporting and mine material characterisation, in Proceedings Life-of-Mine 2016 Conference, pp 183–187 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By A Roudnev, P Loderer

Mineral froth pumping utilising centrifugal slurry pumps is a major engineering challenge for both the end users and pump manufacturers. The traditional approach has been to oversize the pump for pumping mineral froth. New horizontal slurry froth pump designs offer opportunities to improve froth pumping capability of mineral froth with challenging (high) Froth Volume Factor while maintaining high efficiency, long wear life and stable pumping performance.CITATION:Loderer, P and Roudnev, A, 2018. A reliable solution for pumping mineral froth with challenging froth volume, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 291–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By L Brodie-Hally

In the early-1990s, Tad Golosinski, the former the head of mining department at WASM participated in a review mining engineering courses in Australia. The review team asked various industry executives what subjects they thought graduates needed to be taught. Tad made the comment to me that the more senior executives thought that history and ethics were very important. The outcome was that the mining engineering courses were required to contain at least five per cent content dealing in ethics. The course was to be modified to reflect this. Tad thought at the time the students would think that subjects dealing in history and ethics came from retirees and professionals that were over the hill. So let me talk to you today about ethics.

Jan 1, 2002

By T Baumgartl, J Burgess, B Emmerton, P D. Erskine

Large-scale open cut mining in the Bowen Basin has been undertaken for over 40 years. During this period, improved mechanical capability and economics have allowed extraction to greater depths, resulting in post-mining landforms of increasing height. Rehabilitation practitioners face significant challenges in stabilising these landforms and require a comprehensive understanding of the Bowen Basin Coal Measures strata likely to be disposed of during mining. Knowledge regarding the potential behaviour of differing spoil materials (following disturbance) provides a rationale to maximise short- to medium-term surface stability of constructed landforms by identification, salvage and advantageous reuse of cladding resources as a means to minimise erosional risks.CITATION:Emmerton, B, Burgess, J, Baumgartl, T and Erskine, P, 2016. Bowen Basin coalmine spoil classification for improved mine rehabilitation outcomes, in Proceedings Life-of-Mine 2016 Conference , pp 142–147 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By J Walshe, G Duclaux, L A. Fisher, R Hough, J S. Cleverley, M F. Gazley

Characterisation of hydrothermal gold systems across multiple scales is increasingly important for our understanding of ore deposit genesis and for targeting new mineralisation. Published work on multiscale mineral system exploration focuses either on applying a single technique across scales or on incorporating a series of techniques across a limited scale range. Typically, these studiesÆ spatial scales vary from crustal to deposit-scale and have successfully linked the distribution and shape of major orebodies to fault systems or varying lithostratigraphy. But, is this scale small enough to answer fundamental questions about the relative timing, processes interactions and mechanisms involved in the formation of ore deposits? We illustrate the potential of a deposit to microscale study, using the Plutonic Gold Mine in Western Australia as an example, to better understand hydrothermal gold systems. Using an integrated approach combining lithological and alteration logs, various geochemical data set, meso- to microscale structural and textural observations and spatial data assimilation, we have revisited the fundamental processes involved in the formation of this significant gold deposit.CITATION:Duclaux, G, Hough, R, Gazley, M F, Fisher, L A, Walshe, J and Cleverley, J S, 2013. A multiscale approach to hydrothermal gold systems - unravelling mineralisation processes at the Plutonic Gold Mine, in Proceedings World Gold 2013 , pp 95-98 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

The old Trekelano mining area is situated in the Cloncurry Gold and Mineral Field 14 km east-south-east of Duchess. It connected with the main Cloncurry-Dajarra railway line by a private line from Juenburra, a distance of 10 km. The distance by rail from Townsville is 561 km. The area was first mentioned circa 1902 - 1903 when a very short report said, that a Tony Allis had taken a parcel of copper ore out of a mine which, he called æThe InheritedÆ. After that report, nothing further was printed until about 1906, when traces of copper were noticed on a wagon track going to Kiama Well. The Trekelano deposit did not outcrop, with the cap covered by about two metres of soil. The deposit was named after an early pastoral holding. The early prospectors were however disappointed by TrekelanoÆs low copper grades, approximately five per cent Cu. This is understandable when, in those days, about 25 per cent was the cut-off grade for mines in the district. Meanwhile, The Hampden Mining and Smelting Company were constructing a smelter to treat their sulphide ores at Kuradala that was replacing their high grade oxides ore. By about 1910, the Hampden Mining and Smelting Company was experiencing smelting problems, and needed suitable oxidised copper ore to blend with the Kuradala pyritic ore. Someone must have remembered the Trekelano low-grade oxides, resulting in agreement to mine and cart the ore to Duchess, from where it was railed to Hampden, as Kuradala was known at that time.

Jan 1, 1998

By D Caffrey

To demonstrate the advantages of using electronic delay detonators over pyrotechnic detonators, a trial using the DNES Dynatronic System was conducted at the KCGM Mount Charlotte operation in 1998. The trial clearly demonstrated that accurate control over the firing delay time between blastholes can lead to fragmentation improvement and ground vibration energy control which are two important issues for the Mt Charlotte underground operation. Excellent fragmentation was achieved by employing a 12 ms delay sequence. Detailed fragmentation analysis has shown a 10 to 20 per cent passing increase for the rock fragment size from 0.1 to 0.4 m compared with the pyrotechnic detonator firing. There was no increase in ground vibration level on the surface with the electronic detonator firing even though the electronic detonator firing had a much shorter blast duration than the pyrotechnic detonator firing. In fact, our energy calculation has clearly shown that much less energy had been propagated to the surface from the blast using electronic detonator firing.

Jan 1, 1999

By G N. Musafer, M H. Thompson, R C. Wolff, E Kozan

The most important aspect of modelling a geological variable, such as metal grade, is the spatial correlation. Spatial correlation describes the relationship between realisations of a geological variable sampled at different locations. Any method for spatially modelling such a variable should be capable of accurately estimating the true spatial correlation. Conventional kriged models are the most commonly used in mining for estimating grade or other variables at unsampled locations, and these models use the variogram or covariance function to model the spatial correlations in the process of estimation. However, this usage assumes the relationships of the observations of the variable of interest at nearby locations are only influenced by the vector distance between the locations. This means that these models assume linear spatial correlation of grade. In reality, the relationship with an observation of grade at a nearby location may be influenced by both distance between the locations and the value of the observations (ie non-linear spatial correlation, such as may exist for variables of interest in geometallurgy). Hence this may lead to inaccurate estimation of the ore reserve if a kriged model is used for estimating grade of unsampled locations when non-linear spatial correlation is present. Copula-based methods, which are widely used in financial and actuarial modelling to quantify the non-linear dependence structures, may offer a solution. This method was introduced by Bßrdossy and Li (2008) to geostatistical modelling to quantify the non-linear spatial dependence structure in a groundwater quality measurement network. Their copula-based spatial modelling is applied in this research paper to estimate the grade of 3D blocks. Furthermore, real-world mining data is used to validate this model. These copula-based grade estimates are compared with the results of conventional ordinary and lognormal kriging to present the reliability of this method.CITATION:Musafer, G N, Thompson, M H, Kozan, E and Wolff, R C, 2013. Copula-based spatial modelling of geometallurgical variables, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 239-246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013