Search Documents

By M. F. Smith

BELOW the nose of the bainitic C curves in isothermal transformation diagrams, the rate of the austenite-to-bainite transformation usually decreases with decreasing temperature. However, in some steels and iron-carbon alloys, there is a noticeable acceleration in the initial reaction rate at temperatures just above Ms. Such speeding-up of the bainitic transformation would be understandable at temperatures just below Ms because of the catalytic effect of the martensite formed,' but the reversal in isothermal kinetics just above Ms seems quite anomalous. This behavior was observed by Howard and Cohen' in a 1.35 pct C steel and, on the basis of metallo-graphic examination, it was attributed to the formation of a thin plate-like product not belonging in the bainitic sequence. More recently, schaaber2 found two-stage reactions occurring in the vicinity of Ms in a number of steels, and suggested that the first stage might be the isothermal formation of marten-site, preceding the isothermal formation of bainite in the second stage. A decrease in the bainitic incu-

Jan 1, 1960

By M. A. Meyers, P. P. Meyers

The analysis of the phenomena involved in determining the compressive strength of iron-ore agglomerates leads to the identification of important parameters. It is shown mathematically that the pellet rupture strength is proportional to the cross-sectional area. Fracture is initiated at the center of the pellets by the tensile stresses developed by the compressive loads normally to the compressive axis. The variation in strength between individual pellets of identical composition and subjected to identical treatments u due to internal voids of varying sixes that act as stress-concentration sites. Two novel testing procedures are proposed. The first consults of testing the pellets between two plates having three steel spheres each. This configuration simulates much better the environment actually encountered by the pellets. The second procedure consists of a thick-walled cylinder in which a piston penetrates; a large group of pellets is tested simultaneously, as the stress versus strain plot is being recorded. This latter test presents vacant advantages over the conventional testing procedure; the main one is that one single test is sufficient to characterize the mechanical response of the pellets.

Jan 1, 1984

By J. A. Ede

THE object of the writer is to call attention to a rather unique aggregation of economic products distributed over a line of succeeding formations about 3 mi. long, to be seen within a few miles of La Salle, Ill. Fig. 1 is an ideal section of the stratification exposed and exploited along a distance of 3 1/5 mi. in a southwesterly direction from the quarry of the Utica Hydraulic Cement Co. located near the historic site of Kaskaskia village to the Oglesby, shaft at Oglesby. No attempt has been made to cover the whole field, special mention only being made (with the exception of two places) of the operations found along the course or parallel to the direction assumed in the ideal section. I have used Fig. 2, after J. H. Bent and De Witt Kelly, to locate the relation of the La Salle anticline to the coal mines of this district and to show the operation of No. 1 and 3 mines of the Illinois Zinc Co.

Jan 9, 1919

By G. M. Ritcey

Sulphuric acid leaching has been up to the present, the most popular of the leaching routes. Oxide ores are usually leached with sulphuric acid directly by dump leaching, as practiced at the Bagdad or Bluebird Mines in Arizona, or by vat leaching as done at Inspiration Mining in Arizona. Upgrading of the low-grade oxide ores by dump leaching followed by cementation of the copper from solution by scrap iron has been replaced by the leaching-solvent extraction-electrowinning route which results in a high purity product at the mill site at reduced production costs compared to previous practice. High-grade oxide ores, vat leached with H2SO4, can contain, for example, 25 g Cu/l and 25 g H2S04/,l, or higher concentrations of both, and are presently fed directly to electrorefining plants. Advantages of coupling solvent extraction-electrowinning with the low cost dump leaching instead of using cementation, are as follows (1): a) the production of high purity electrolytic copper rather than cement copper;

Jan 1, 1978

By Robert Glass Cleland

THE THIRD and most important item on the Phelps Dodge agenda for the development of new ore supplies involved the site of the company's initial venture into Arizona, the old mining camp of Morenci. By the purchase of the Arizona Copper Company's holdings in 1921, Phelps Dodge had obtained control of virtually the entire Morenci district, including town, public utilities, and, above all, the huge mineralized area that had once been divided between numerous competing companies. Because of this rigid concentration of ownership in the hands of one organization, Phelps Dodge was able to plan and successfully carry out a program of greater magnitude than any Arizona mining company had previously under- taken. The immense deposit of low-grade ore, usually referred to as the Clay Orebody, had been known to the mining companies of Morenci for many years. Pioneer exploratory work, both by the Arizona Copper Company and later by Phelps Dodge, revealed that the deposit, mostly of light-gray porphyry rock, lay under a hard capping from two hundred to five hundred feet thick. An intensive drilling

Jan 1, 1952

By E. N. Harshman

Uranium mining and milling are rather new industries in Wyoming and South Dakota, but, in the past 15 years, ore valued at more than $400,000,000 has been mined and milled in the region. The major uranium deposits are in structural and/ or erosional basins or on the flanks of uplifts. The principal host rocks are medium- to coarse-grained sandstones that were deposited in continental or brackish-water environments and were derived in large part from the granitic cores of the uplifts and the sedimentary rocks that flank the cores. The ages of the host rocks range from Cretaceous to Miocene, but more than 95 per cent of the known reserves in the region are in rocks of early Eocene age. The bulk of the ore in the region is unoxidized and lies below the water table; some oxidized ore has been mined in the Powder River Basin and Black Hills districts. The unoxidized ore comprises pyrite, uraninite and/ or coffinite, marcasite, hematite, jordisite(?), and selenium. Minerals in the oxidized ore include hydrous uranium carbonates, phosphates, and sulfates and hydrous uranium and/ or vanadium silicates. The deposits are in the form of ore rolls that contain from a few hundred to a few hundred thousand tons of ore, ranging in grade from 0.1 per cent to 1.0 per cent U3O8. The rolls are at the margins of large tabular bodies of sandstone that has been altered by the orebearing solutions. The deposits are believed to have resulted from the interaction of an alkaline; oxidizing, ore-bearing ground water and a reducing environment. Exploration guides include the spatial relations of ore to altered sandstone, favorable lithology in the host rock, the content of certain elements and/ or compounds in ground water, and the relation of deposits to major paleodrainages.

Jan 1, 1968

By J. C. Detweiler

THE Jacksonville plant of Humphreys Gold Corp., operating under leases from National Lead Co. and Rutile Mining Co. of Florida, recovers rutile, ilmenite, zircon, and monazite from an ancient beach deposit containing about 2.5 pct of these minerals in combination. The location of the plant is unique, being situated about ten miles from the center of Jacksonville, Fla., surrounded by a thriving suburb. Two four-lane highways pass within 1 ½ miles of the plant. An expressway now under construction will pass over the tailing pile, within 500 ft of the mine office. The elevation at the plant site is approximately 50 ft above sea level. This is one of two mines producing titanium minerals and zircon in Florida. Another mine is also operated by Humphreys at Starke, about 50 miles southeast of Jacksonville. The Jacksonville deposit extends about six miles in a north-south direction, averaging approximately one half mile wide and twenty ft thick. Values begin at the surface over most of its length and ter-

Jan 1, 1952

By T. B. Nolan, R. N. Hunt

In terms of present metal prices, analysis of extant records of the Eureka district indicate past production of the magnitude of $200,000,000 in recovered silver, lead, and gold. Production to date has been thoroughly oxidized ore from massive replacements, fissures, manta, and pipe-like bodies-in large part from the massive Eldorado (middle Cambrian) and Hamburg (middle to late Cambrian) dolomite horizons. In the productive area of about 6 square miles carbonate rocks comprise 80 per cent of the section, which includes early Cambrian to late Ordovician horizons. Four-fifths or more of the district's production came from a block of Eldorado dolomite in Ruby Hill that was moved in over younger horizons on strands of a regional thrust fault. The lower 500 to 600 feet of the block was much fractured and brecciated and became host to the ores. The Ruby Hill fault, a late normal fault, limits the Ruby Hill block of dolomite on the north for its entire length of nearly a mile and terminates the downward extent and exploitation of its ores. It introduced an hiatus of some 40 years in the district's development. Drilling of the past 20-odd years, followed by underground work, has now exposed the down-faulted extension of the Ruby Hill block of Eldorado dolomite and its contained ores, dropped 1800 feet in a dip shift to depths beneath the surface of 2000 to 3000 feet. The ores at depth are the sulfide counterpart of those mined in early years on the footwall side of the fault. The ores of the district may be attributed to the same source as the intrusive quartz diorite outcropping in a limited way south of Ruby Hill but found at depth elsewhere in drill holes. The long north-south axis of the district, its anticlinal structure, its major faults, and the distribution of the intrusives and, in their relation to the surface, the ores themselves, all suggest that erosion has not cut deep enough to expose the extent of intrusives and the ores consequent upon them.

Jan 1, 1968

By William R. Jones, Robert M. Hernon

This report on the Central mining district of New Mexico is the partial culmination of an intensive U.S. Geological Survey effort dating back some 30 years. Robert M. Hernon went to Silver City in 1948 to finish a detailed restudy of the district that had been started in the thirties by Samuel G. Lasky. He was joined by William R. Jones in 1951, and Jones took over as project chief when Hernon resigned to do consulting work in 1953; it was under Jones' guidance that most of the work was brought to completion or nearly so ( 17, 22-24, 26-30). Hernon returned to the Survey in 1958 to work in .the southern Appalachians. Early in 1965 Jones urged that Hernon be reassigned to the Silver City project to help complete the Professional Paper report on the ore deposits of the Santa Rita quadrangle as well as to take over preparation of the report on the Central district for the Graton-Sales volume. This reassignment was approved, and Hernon began work on the present report. By late June he had completed most of it in draft form, and on June 28 Jones and Hernon left Denver for a short trip to Silver City to fill in a few gaps and to reacquaint Hernon with activities in the district, which he had not visited for 12 years. Late in the afternoon of June 29, 1965, as Bob and Bill were 85 miles short of their destination, their jeep collided head-on with a truck that was attempting to pass another vehicle in a cloud of dust. They both died instantly. As the most recent surviving member of the Silver City project (1958-1962), I was given the honorable though rather sorrowful task of putting the Hernon-Jones report "in shape" for publication. Fortunately the manuscript was already in good shape, so that the task has consisted of little more than minor reorganization and editing, and of preparation of the illustrations, abstract, and bibliography. The sections on wall-rock alteration had been left for Jones to complete in the light of his recently intensified interest in alteration geochemistry (25), and it is in these sections only that. the report may fall short, for they have been filled in from a 1958 manuscript by Jones on the ore deposits of the Santa Rita quadrangle that he intended to revise considerably. The shortcomings, however, are largely in the interpretation, not in the field data. As a brief but accurate summary of what was known about the geology of the Central mining district in 1965, this report stands as a fitting testimonial to the scientific dedication of two exceptional men.

Jan 1, 1968

By Edward L. Beutner, Robert M. Crump

Benson Mines low-grade iron ore reserve is a replacement deposit within the Grenville gneisses of the Adirondacks. The average grade of the crude ore is about 23 per cent iron. The iron minerals are principally magnetite and hematite disseminated throughout the gneisses as discrete grains about 1 mm in size. Both the ores that are beneficiated by magnetic means and the non-magnetic ores that are treated by a gravity method of concentration are found in stratigraphically different positions but are mined from one open pit, which is about 2.5 miles long and 800 feet wide and are treated separately. The gneisses are described and named according to the distinctive mineralogy of each. Recognition of the gneissic types permits the interpretation of the structure as a northward-plunging syncline overturned to the west. A large subsidiary anticline-syncline complex occurs on the east limb of the major syncline. Iron minerals in sufficient quantity to be considered ore are confined to areas where the footwall rock has been overturned to become the hanging wall.

Jan 1, 1968

By Paul E. Melancon, Vincent C. Kelley, Dale F. Kittel

Uranium of the Grants region occurs predominantly in continental sandstones of the upper part of the Jurassic Morrison Formation, but significant lesser deposits are found in limestone of the Jurassic Todilto Formation and in black shale of the Cretaceous Dakota Formation. The deposits are disseminations that form runs ranging from a few hundred tons to several million tons. The ore consists mainly of uraninite, uraniferous carbonaceous material, coffinite, and such secondary oxidized minerals at tyuyamunite, carnotite, and uranophane. In sandstone, the ore runs were locallized by mudstone, interstitial carbonaceous material, and primary sand channel trends. In limestone, ore deposition was related to folds and fracture zones. The great bulk of production has come from the Ambrosia Lake mines in the Grants district and the Jackpile and Paguate mines in the Laguna district. The ores, which generally have been 0.20 to 0.30 per cent U3O8, are treated at mills operated by Kerr-McGee Corporation, Homestake-Sapin Partners, and The Anaconda Company, all in the Grants district. In 14·years after discovery in 1950, the deposits had yielded concentrates valued in excess of $800,000,000. Since deposition of the Jurassic host rocks, a geologic history involving tilting, faulting, erosion, changing ground-water environments, and oxidation has considerably influenced the existence and character of the deposits. It is evident that their ongm is not simple. However, a degree of agreement appears probable for a pre-Dakota age for the original ore runs, and, at Ambrosia Lake, two principal stages of ore formation, separated by Laramide faulting, are recognized. All earlier ores have been modified by Quaternary oxidation, solution, and enrichment during which time much secondary tyuyamunite, metatyuyamunite, carnotite were formed.

Jan 1, 1968

By AIME AIME

QUALITY and size do not ordinarily go hand in hand, but there is good evidence that both these attributes reached a new peak at the Annual Meeting of the Institute in New York just concluded. Certainly, the total attendance of 2500 was far above any yet attained, as might be expected with the recent rapid growth of Institute member- ship. General comment indicates that the quality of the papers also was notable, though not measurable by so definite a yardstick as attendance. During the meeting 49 technical sessions were held, at which more than 250 formal papers were presented. In addition, there were some thirty special meetings of committees, Divisions, and other Institute groups. In reporting the Annual Meeting eleven years ago the statement was made that "unless the Engineering Societies should build for themselves a new building it is probable that no meeting can be larger," and "the fifth floor, where a buffet lunch is served each day, has reached its full capacity and it seems quite evident that any future development of Institute meetings must be along the lines of quality, not size." Unfortunately the angel to succeed Andrew Carnegie, who financed the building of the present home of the Institute 35 years ago, has not yet ' appeared. Even if some one would merely build another elevator or two in the present building it would help. Fortunately, the modern auditorium of the American Radiator & Standard

Jan 1, 1940

By David White

Jan 1, 1925

By Dean S. Rogers

The conventional role of exploration, development and grade control is examined in this paper within the context of the many and varied types of gold occurrences which are found at the Dome Mine. The account endeavours to trace the development of the total ore evaluation process, from diamond drilling through the exploration and drifting stage, to the stope development and planning phase of the operation, with an emphasis on sampling techniques and assaying procedure. The concept of ore reserve calculations is developed and the practice of grade control is described. In summary, the role of the geological, the engineering and the mining department is presented in relation to the contribution each has to make in the evaluation and exploitation of ore from one of the world's classic Archean gold deposits.

Jan 1, 1985

By Roger L. Beals, George A. Tweedy

I. INTRODUCTION. THE results of the cyanide-operations, given in detail in the following paper, show the progress that is being made at the Minas del Tajo. The old pan-amalgamation process, in operation up to and including 1905, while paying a profit on high-grade ores, was no longer able to treat profitably the ores in sight at that time, hence an alteration in the process was imperative. The success of this alteration is eloquently expressed by the following data Pan- Amalgamation. Cyanidation. 1905. 1907. 1903. Tons treated, . . 51,387 53,983 69,300 Value per ton (U. S. currency),. $10.75 $8.39 $8.28 Extraction, per cent., 65.00 88.50 S7.45 Extraction, per ton. .- $7.00 $7.4.; $7.24 Total cost, per ton treated, 6.50 4.311 4.01 Profit, per ton treated, . . 0.50 3.07 3.23.;

Feb 1, 1910

By Walter S. White

The Michigan native-copper district has produced about 5,400,000 tons of copper since mining began in 1845. The copper occurs primarily as open-space fillings and replacements in amygdaloidal flow tops and conglomerate beds of the Portage Lake Lava Series, of middle Keweenawan age. Secondary minerals with which the copper is associated include microcline, chlorite, epidote, pumpellyite, prehnite, quartz, and calcite; zeolites, other than laumontite, are not abundant. A zonal pattern of the secondary minerals transects bedding and suggests regional metamorphism mainly to the grade of the prehnite-pumpellyite graywacke facies of Coombs. Most of the major copper deposits are near the upper limit of abundant quartz in this zonal pattern. The distribution of copper in both amygdaloid and conglomerate deposits is controlled partly by primary permeability of the rocks and partly by later tectonic fracturing that was concentrated in the mechanically weak flow tops and sedimentary beds. Ore shoots and deposits are therefore controlled partly by primary structural features, such as areas of thick and thin fragmental amygdaloid or the boundaries of conglomerate lenses, and partly by regional structure: a number of ore deposits are in synclinal downwarps. The copper-bearing solutions that formed the deposits were ascending. They may have come from a large concealed intrusive, or may have been driven out of the porous tops of lava flows when the rocks were compacted and metamorphosed at great depth in the central part of the Lake Superior syncline. The second hypothesis seems more consistent with the widespread distribution of the copper, its relation to mineral zoning that represents truly regional metamorphism, its native state, and the likelihood that copper deposition was later than most or all of Keweenawan volcanism.

Jan 1, 1968

Prof. A. Ledebur, Freiberg, Saxony :* Mr. Sauveur has presented and enriched with original observations a valuable summary of the theories advanced hitherto concerning the hardening of steel; but in one particular, it seems to me, his statements call for correction. He says:

Jan 1, 1898

By Paul F. Kerr, Donald M. Hausen

Fine colloidal gold near Carlin, Nevada is disseminated in leached carbonate strata of the Roberts Mountains Formation in the Lynn "window" of the Roberts Mountains thrust fault. The ore body is generally stratiform and is more or less conformable to altered beds near the top of the formation, underlying Devonian limestones. Two sequences of mineralization are recognized: ( 1) an earlier base metal-barite assemblage related to early Cretaceous intrusives (121 ± 5 m.y.), and (2) a later low temperature Au-As-Hg-Sb assemblage of near surface emplacement. The earlier sequence consisting of sparse galena and sphalerite in barite with anomalous amounts of zinc, lead, nickel and copper, associated with dikes of dacitic composition, is of little economic importance. The later sequence of gold, realgar, cinnabar, and stibnite associated with extensive silicification and argillic alteration of limestone beds, has resulted in important deposits of gold. Argillic alteration of hydrothermally leached carbonate strata has provided the environment in which the most prominent gold deposition took place. Carbonate minerals in the limestone host rock have been replaced by microcrystalline quartz and chalcedony to form stratiform silica masses and recrystallized lenses of euhedral quartz. Zones of porous silicification are light gray to white, elliptical in shape, and more or less follow bedding. Silicification is bordered by argillic alteration and pyritization. Deposition of gold usually lies in a zonal pattern that encircles chimney areas of silicification.

Jan 1, 1968

By Hal T. Morris

The main Tintic mining district in central Utah has produced approximately 13,500,000 tons of ore, containing silver, lead, gold, copper, zinc, and other metals, valued at more than $315,000,000. More than 90 per cent of this ore has come from large, irregular ore bodies that have replaced folded and faulted limestone and dolomite strata. Of lesser importance are replacement veins that chiefly cut contact-pyrometasomatized carbonate rocks and fissure veins that cut altered intrμsive bodies and volcanic rocks. The district is in the west-central part of the East Tintic Mountains, a north-trending fault-block range near the eastern margin of the Great Basin. The consolidated sedimentary rocks exposed at the surface and in mine workings are miogeosynclinal deposits more than 10,000 feet thick that range in age from late Precambrian to Late Mississippian. They are folded and strongly faulted and are partly overlain by volcanic tuffs and agglomerates and by extensive flows of porphyritic and vitrophyric quartz latite, latite, and trachyandesite of Eocene age. All of these rocks are locally concealed beneath thick alluvial deposits of Pliocene and Quaternary age. The Eocene and older rocks are cut by dikes, sills, and small stocks of porphyritic quartz monzonite, monzonite, and latite, which are genetically related to the ore deposits. The district is inactive except for the production of halloysite clay and for minor leasing activity and exploration ventures. Several exploration targets remain untested.

Jan 1, 1968

By E. F. Jr. Young, H. E. Steinman, G. C. Smith

Through a progressive laboratory and pilot-plant program Jones & Laughlin Steel Corp has analyzed and corrected mine drainage pollution problems at all of its coal mines. In conducting this program, the company found no "typical" drainage discharge. Each discharge point at each mine was unique, so that varied approaches were needed to eliminate stream pollution. To illustrate the variety of these approaches, the treatment of drainage from foul, discharge points at three mines in Pennsylvania will be considered here. The flows and critical analyses of the drainage sources and treated effluents arc shown in Table I. Hydrated Lime Works at Thompson Borehole The discharge stream from the Thompson bore- hole at the Vesta No. 5 mine flowed into a small branch creek where it created a "yellowboy" deposit and affected aquatic life. Investigation indicated that hydrated lime would neutralize the acid and precipitate ferric iron without aeration. Treatment of the 150.000-gpd flow, however, created about 4000 gpd of wet sludge for which there was no nearby accumulation site. With State approval, this sludge was deposited through an unused borehole into an abandoned section of the Vesta No. 6 mine several miles away.

Jan 1, 1970