Search Documents

By J. H. Zietsman, M. W. Erwee, Q. G. Reynolds

Pyrometallurgical furnaces, essential for metal extraction, operate at temperatures exceeding 1600°C and represent complex multiphase systems that challenge direct industrial research. Multiphysics models play a key role in shedding light on their intricate behaviours, supporting the refinement of design and operational strategies. Integral to the operation are the tap-holes, which facilitate the removal of molten products and are routinely opened by lancing, a process comparable to the use of a cutting torch, where high temperatures result from oxygen reacting with an iron lance. When the lance pierces the clay, oxygen gas enters the furnace, which could influence the behaviour of the molten material inside. In this work, a multiphase fluid flow model was used to investigate bulk flow dynamics, with a focus on the effects of the lancing process on the inside of the furnace, immediately behind the tap-hole. Incompressible and compressible multiphase fluid solvers were used and compared with respect their performance – the intention was to assess whether using a compressible solver would yield a different solution to the incompressible one. It was concluded that there are negligible disparities in bulk fluid flow behaviour between the solvers for the case studies examined, indicating that solver selection might be less consequential for certain aspects of oxygen lancing.

Apr 16, 2024

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001

By John F. Gamble

Paper 1?South African experience with asbestos-related environmental mesothelioma: Is fiber type important? Neil White, Gill Nelson, Jill Murray The purpose of this review was to illustrate the importance of the type of asbestos in environmental mesothelioma. South Africa is a logical place to assess fiber type. The three major types of asbestos (crocidolite, amosite and chrysotile) were mined (all asbestos mining stopped in 2002) in South Africa. The association between asbestos and mesothelioma was discovered in South Africa. The occupational literature indicates high mesotheliomagenic potential for crocidolite, less for amosite and less still for chrysotile. Since South Africa has been a major source of crocidolite, relatively high rates of mesothelioma in the mining population is not surprising. High rates of mesothelioma due to environmental exposure is surprising, except perhaps when the authors? point out potential sources for community exposures (e.g., mine tailings used for road surfacing, golf courses, brick and plaster making; insulation in residential ceilings; children playing on fiber-rich waste rock). The authors? reviewed four studies reporting on mesothelioma cases and their sources of exposure and fiber type. Overall 23% of the known cases were attributed to the environmental (not occupational) exposure and about 90% were due to crocidolite asbestos. The proportion of environmental mesothelioma is considerably higher than in Western Australia where crocidolite is also mined. There the overall rate of environmental mesothelioma is about 6% (and less than 1% from residence in a crocidolite mining area).

Jan 1, 2007

By R. G. Gürtunca, J. A. Breslin

This paper briefly describes the progress in mine safety in the United States, with emphasis on recent events that have followed since the explosion at the Sago Mine in January 2006. Legislation following the mine accidents last year and areas of work carried out by the National Institute for Occupational Safety and Health (NIOSH) related to the accidents are discussed. American coal production in 2006 was 1,150 million short tons. Most of this coal is consumed domestically, with annual exports of coal about 50 million tons. One third of annual production is produced at surface mines and the rest from underground. This coal is produced by about 82,000 miners working at 1,400 coal mines. Major improvements in coal mine safety have been made in the US since the Federal Mine Safety and Health Act of 1977. The fatal injury rate in underground coal mines between 1977 and 2004 was reduced by 47.8% to 0.036. The annual number of fatalities dropped from 112 to 14 during that period. Likewise, the non-fatal days-lost injury rate was reduced by 42.6% from 10.87 to 6.24. The improvements in mine safety during this period can be seen in the graph of underground coal mine explosion fatalities and injuries from 1980 to present, which is shown in Figure 1. Between 1984 and 1993 (9 year period) there were 5 explosions and one major mine fire, for a total of 55 fatalities. Over the seven year period from 1993 to 1999 there were no fatalities from coal mine fires and explosions. However, in the six years since 2000 there have been 5 explosions and one fire, which have caused 37 fatalities. [ ]

By Chas. F. Jackson

This bulletin is one of a series of Bureau of Mines reports dealing with mining methods, practices, and costs. A study of this subject was undertaken by the Bureau in cooperation with a large number of mining companies in 1928. This study continued for 5 years, during which engineers of the Mining Division of the Bureau visited most of the larger mines and many smaller ones in the United States, as well as several mines in Canada and Mexico. As a result of this study, 75 reports dealing with underground mining methods and costs at different mines were published as information circulars. Circulars also were issued on 6 open-pit mines and 2 gold-dredging operations. These circulars were written by the managers, superintendents, and engineers in charge of the operations, in some instances in collaboration with Bureau engineers. They were prepared according to a standard outline drawn up by the Bureau to obtain uniformity in textual treatment and in the arrangement and basis of setting up cost and operating data.

Jan 1, 1936

By Morabito J, Harrop D. W

Uranium exploration was commenced in 1973 and carried out at a regional scale over a wide area of the northern part of the Camarvon Basin of Western Australia by Minatome Australia Pty Limited and their joint-venture partners. As a result, pervasive uranium mineralization has been found in the Cretaceous sandstones near Manyingee Hills in the Onslow Region, which were probably deposited in a near-shore, fluvia deltaic palaeo-environment.Mineralization is generally found in poorly sorted argillaceous sandstones and siltstones near redox fronts formed by oxidizing waters circulating in reduced sediments. The principal minerals found in the two Manyingee deposits delineated so far are coffinite, uraninite with associated pyrite in the reduced zones, and phosphuranylite, siderite and limonite in the oxidized zones. The presence of dissolved uranium in the superficial aquifers, of secondary uranium minerals as coatings on granitic rocks, and of recent uranium-bearing calcrete sediments, suggest that the whole Cretaceous-Precambrian system has been subjected to the formation ofroll-front type uranium deposits since the Cretaceous. Continuing exploration is locating additional uranium occurrences. The deposits outlined so far are being evaluated for their amenability to in situ leaching tests planned for 1982-1983.

Jan 1, 1981

Computer applications are ideally suited to the day to day operations of grade control and short term planning on a mine site. By refining this part of the operation there is scope to increase profits by more accurately predicting ore grade and tonnage, and allowing the mining engineer more flexibility in his approach to scheduling. Large numbers of blasthole or ditchwitch samples need to be processed in a fast and efficient manner, and stored in a database for future reference. The mining engineer has to calculate tonnages and subdivide the blast or digging area into mineable areas of waste, low and high grade ore. New grade and tonnage information must be used by the mining engineer to update his short term plan. Answers must be obtained quickly and efficiently, but a high level of individual input is necessary in order that maximum use is made of the information. Geostatistical analysis of samples can be used to refine the interpolation techniques. Reconciliation between the original grade model, the newly sampled area, and the final product should be monitored continually.

Jan 1, 1989

Multilevel-multiseam hardcoal mines on the European continent usually consist of a huge network of underground openings, sometimes more than 200 km long in total, with some longwalls operating down to a depth of 1,500 m. While operating several longwalls simultaneously, these mines are making use of a number of stationary and mobile measurement- and analysis units in their main ventilation passes combined with atmospheric measurements on the surface. This paper provides an overview over the systems and technology used and describes the typical set-up of a measuring net. To detect and monitor underground fires through fire gases measurement and -analysis, a mobile underground testing laboratory collects data locally in the area of the fire. These laboratories have proven to be extremely useful not only during the actual fire fighting but also for the long-term gas measurements in critical mine areas. They have repeatedly detected starting fires and have thus given the mine the opportunity to react early and to avoid larger damage. Therefore several mobile laboratory units have now been installed for long-term testing in a number of German mines and similar units are being used in the Czech Republic and Poland.

Jan 1, 2012

Results of laboratory studies on the flotation of marmatite (zinc sulphide) with new reagents, which were developed to avoid the use of copper sulphate, are presented.Episulphides were chosen as the basis for the reagents because of their reported special chemical affinity for zinc and cadmium. Attempts were made to solubilize and introduce functional groups to episulphides with organic and inorganic acids, ammonia, phenol, aniline, diethylamine, and pyridine. As a class of reagents, the episulphide-amine combination was generally found effective in zinc sulphide flotation to a greater or lesser degree. Best results were obtained with ethylene sulphide-aniline combination. Although anilino-ethyl mercaptan is the reported reaction product of aniline and ethylene sulphide, it was concluded that the effective zinc sulphide flotation with ethylene sulphide-aniline combination is not entirely due to the formation of the mercaptan.The economics of the possible usage of ethylene sulphide-aniline reagent are discussed.

Jan 1, 1974

By Jose R. Hernandez-Aguilar

"Three models to predict the effect of bubble size (Db) on metallurgical response were tested in a pilot-scale flotation column at Teck Highland Valley Copper mine. The column was fed with slurry collected from the Cu/Mo separation circuit. The first model was the one developed by Gorain et al. (1997), which assumes that the collection zone rate constant (kc) is inversely proportional to Db. The second model was the one proposed by Hernandez-Aguilar et al. (2010), which considers kc as an inverse square function of Db. The third model was the one developed by Yoon and Luttrell (1989) which provides expressions to describe the efficiency of particle collection (E) based on first principles. The results showed a significant bias between experimental and predicted data using the model of Gorain et al. (1997), possibly reflecting the model’s inability to explain the impact of bubble size, bubble rise velocity and flow regime on E. The model of Hernandez-Aguilar et al. (2010) well described the experimental evidence. The model of Yoon and Luttrell gave accurate and unbiased predictions. However, Yoon and Luttrell’s approach calls for a criterion to determine whether the flow regime is potential or intermediate, a subject that requires more fundamental research.INTRODUCTIONParticle collection, i.e., bubble-particle collision followed by attachment, is the basis of flotation. In a quiescent environment (such as the one observed in a column, or away from the impeller in a mechanical cell), a collision event can take place as long as the “degree of turbulence” caused by the rising bubble does not prevent particle and bubble to flow in close proximity. Upon collision, the particle slides on the bubble surface for a period of time. If the particle is hydrophobic, attachment occurs when the “sliding time” is longer than the “induction time”, which is the time required to thin and rupture the intervening liquid (usually water) film forming a three-phase contact angle. While the induction time is largely influenced by the degree of hydrophobicity of the particle, the degree of turbulence is governed by the bubble size. Generally, direct control of bubble size is not exercised by most mineral processing practitioners, in spite of its obvious importance. Studies to model the effect of bubble size on particle collection using fundamental approaches have been conducted (e.g., Anfruns and Kitchener, 1977; Webber and Paddock, 1983; Yoon and Luttrell, 1989; Dai et al., 1999). However, these models have been validated under highly idealized laboratory conditions (micro-scale experiments using single minerals and uni-sized bubbles), far from resembling those existing in practical industrial applications. Fundamental studies to interpret the effect of bubble size on particle collection in industrial environments are largely absent in the literature. Partly because of this lack of practical knowledge, many mineral processing practitioners perceive laboratory “bubble size” studies to be valuable academic exercises, but not something that can be directly applied to daily production issues."

Jan 1, 2011

By J. W. Davis

In the last few years major industrial companies have begun to realize the importance of Reliability as an enterprise strategy that, properly implemented, will improve financial performance. Typical results of an effective Enterprise Reliability Strategy include a 20% -50% reduction in maintenance cost accompanied by a 5% - 10%increase in real production capacity, with no capital investment in production equipment. One factor fueling the race to acquire and implement enterprise reliability is the pressure for companies to be increasingly cost-effective and competitive in global markets. In a recent study, Asset Productivity: The Next Wave, the Boston Consulting Group (BCG)stated that, “In order to compete for funds, companies must offer investor returns that are competitive with other opportunities. Alternative investments such as dot-com and others with non-traditional business models have raised the bar.” (APDF version of the study can be downloaded at www.bcg.com). BCG views asset productivity as the most powerful mechanism for increasing shareholder return. The author believes that the most effective way to increase Fixed Asset Productivity is to maximize asset utilization by increasing the Reliability of the Assets and the associated processes. Developing and implementing an ERS requires significant effort and knowledge. Most companies have difficulty finding a sufficient supply of these valuable commodities to implement an ERS Program internally. Many companies also struggle with figuring out how to get started and what direction to proceed.

Jan 1, 2003

Recycling and Recovering Fine Particles from Auto Shredding Residue (ASR/SR) to Conserve Raw Materials and Protect Environment

Sep 13, 2010

By S. Frimpong, S. R. Dindarloo

Material handling in open pit mining accounts for about 50% of production costs. The selection and deployment of efficient, safe, and economic loading and haulage systems is thus critical to the production process. The problems of truck and shovel selection and sizing include determination of the optimal number and capacities of haulage and loading units, as well as their allocation and operational strategies. Critical survey and analysis of the literature has shown that deterministic, stochastic, and experimental approaches to these problems result in considerably different outputs. This paper presents a comprehensive simulation framework for the problem of truck and shovel selection and sizing based on the random processes underlying the network-continuous-discrete event nature of the mining operation. The framework builds on previous research in this field and attempts to address limitations of available methodologies in the form of a comprehensive algorithm. To test the validity of the framework a large open pit mine was evaluated. The stochastic processes governing the uncertainties underlying the material loading and haulage input variables were defined and built into the stochastic model. Discrete event simulation was used to simulate the stochastic model. The proposed model resulted in several modifications to the case study.

Jan 1, 2015

By Daniel Hauer

Blocking. (5) The “blocking” of boulders is a much cheaper way of breaking them up than “mud capping.” It should always be used in preference to that method except when too much time will be consumed by a crew of men waiting for the drilling to be done, as shown in example of cost No. 1, as given under “mud capping.” Under such circumstances the time consumed would be a greater cost to the contractor than the extra amount of dynamite. Then, too, on large thin boulders to drill one hole would result only in breaking the stone into such pieces as would again have to be broken; and the many holes might equal the cost of extra dynamite. Under such circumstances if method (6) cannot be used, “mud capping” will have to be resorted to, to do the work economically.

Jan 1, 2006

By S. Bargigli, S. Ulgiati, M. Raugei, F. Cherubini

Metallic magnesium is mostly used in lightweight alloys in order to decrease fuel consumption in automotive applications. Several different production processes are currently used worldwide, and the magnesium production scenario is changing rapidly, with Chinese production increasingly dominating the world market. For the purpose of this paper, a novel approach to Life Cycle Assessment was applied, in which Material Flow Accounting and energy-based methods (Embodied Energy, Exergy and Emergy Analyses) are integrated and complemented, with a detailed description of the environmental hazards associated with emissions from all the different processes.

Jan 1, 2005

SEVERAL serious accidents, which had occurred owing to the platman leaving the plat without first withdrawing the "chairs" from the shaft, set the writer scheming to devise a mechanically operated system which would obviate such accidents and be "fool-proof". It was obvious at the outset that some means of indicating to the engine-driver by the movement of the "chairs" themselves, whether they were "in" or "out" of the shaft, was necessary.An arrangement of signalling similar to railway semaphores was considered, but was rejected owing to the difficulties accruing from the large number of communicating wires which would be required down the shaft-viz., 2 for each level. After several experiments, a comparatively simple and efficient electrical system was devised, and which is covered by Commonwealth Patent TO. 10,402.One of the chief features of the apparatus is its simplicity, and its strongest point is the fact that both the engine-driver and platman receive visual indication of the position of the "chairs." The arrangement consists of a miniature coloured glow lamp, one for each level of each shaft compartment, arranged and placed beside the numbers and arrows corresponding to the various levels, on the winding engine indicators. Also a large indicating glow lamp is installed at each compartment in the various levels, in proximity to the levers for operating the "chairs." Upon operating the various levers for the "chairs," an electrical current...

Jan 1, 1909

By N. Z. Fotoyi

Keywords: MgO-MgR2O3 refractory, SO2-containing gases, chemical attack The reaction mechanisms occurring when MgO-MgR2O3 refractories are exposed to SO2-containing gas atmospheres were examined. The study examined the characteristic structures of magnesite-chrome, chrome-magnesite and magnesite refractories exposed to SO2-O2 gas mixture at temperatures of 700°C to 1350°C. The phase characterization was conducted with scanning electron microscopy (SEM) and powder X-ray diffractometry (XRD). The results show that the physical characteristics of the refractory matrix along the grain boundaries are important refractory features during chemical attack from SO2-containing gas. Upon heating in SO2-containing gas, the changes in phase-chemical compositions and accompanying grain growth causes loosening of the structure and the pore volume promotes gas diffusion. The chemical reactions that occur form stable sulfate compounds identified as MgSO4, CaSO4 and CaMg3(SO4)4, and lead to disintegration of various phase structures and consequently erosion of the refractory. In conclusion, the reaction mechanisms in MgO-MgR2O3 refractories exposed to SO2-containing gases progress through a combination of structural disintegration and chemical attack.

Jan 1, 2011

Most types of nuclear power reactors use uranium dioxide fuel. Power reactors using natural uranium dioxide fuel are of special interest to countries such as Australia that have their own uranium supplies. A wide range of uranium dioxide powders can be fabricated and the ideal one flows readily, presses without the need for binders or lubricants, sinters to the required density and gives low reject rates at all fabrication stages. Sinterable uranium dioxide is usually produced via the ammonium diuranate route.The Australian Atomic Energy Commission is aiming to demonstrate production of nuclear grade uranium dioxide from Australian concentrates, improving technology where possible. Details are given of the dissolution, solvent extraction, precipitation, filtration, drying, and· calcination-reduction steps. Solvent extraction from sulphate media is also under study with a view to developing a process to produce a nuclear grade product at the mine treatment plant site.

Jan 1, 1970

By K. Loutet, A. Guenkel, K. Nikolaisen

"The INCO SO2/air process was patented by INCO in 1985. Well over 80 mining operations worldwide are using this process to oxidize cyanides to cyanates in the tailings from gold, silver and copper mining operations. The sulphur dioxide (SO2) for this process can be supplied either as liquid SO2, SO2 gas or as a sulphite-based salt. The majority of SO2/air operations have used sulphite-based salts as the ‘SO2’ equivalent probably due to low capital cost. Liquid SO2 has also been used frequently, but due to concerns with safety and availability, this option is often not preferred. The solid salt sodium meta-bisulphite (SMBS) is commonly employed, but its cost is an order of magnitude higher than that of sulphur. Due to the high cost of SMBS, the increased capital cost for a sulphur-burning SO2 gas plant (green field or retrofit) usually has a pay-back of less than three years. In addition, a SO2 gas plant offers potential for significant heat recovery from the sulphur burning process. In terms of safety, the SO2 gas plant only requires the storage of relatively benign sulphur and the site inventory of SO2 will be limited to the plant gas volume. Therefore, a SO2 gas plant will not trigger the Canadian Environmental Protection Act (CEPA) E2 Regulations or the US Clean Air Act Section 112(r) accident prevention regulations, as may be the case for liquid SO2.Most existing mining operations using ‘SO2’ are gold operations, but in recent years there has been an increased interest in larger sulphur dioxide gas plants for hydrometallurgical facilities that employ leaching of cobalt/manganese minerals or precipitation of manganese/iron (e.g. Tenke Fungurume and El Boleo).This paper focuses on the production of sulphur dioxide gas generated on site and on demand for the use in hydrometallurgical processes. The capital and operational costs of a SO2 gas plant is compared to conventional process alternatives using sulphite-based salts or liquid SO2."

Jan 1, 2016

Located in Timmins, Ontario the Porcupine Joint Venture, a pooling of assets between two existing operations (the Dome Operation of Placer Dome (CLA) and the Hoyle Pond Operation of Kinross Gold Corporation) came about on July 1st, 2002; Placer being the manager of the Joint Venture with 51% ownership and Kinross with 49%. The formation of the Joint Venture was the realization of the dream of many who could envision the benefits of the whole area being operated as one entity ? the combination of the majority of assets in the Porcupine Camp into one venture containing tremendous synergistic potential of manpower, infrastructure, land tenure and exploration development. The name Porcupine in the gold mining industry brings with it the legacy of world class gold mines; the Hollinger, McIntyre and Dome with a proud tradition of excellence. The name Porcupine brings with it the legacy of over twenty individual mining companies in operation at any one time, producing over 65 million ounces of gold.

May 1, 2003