Search Documents

By J. -F. Lagueux

Goldex Mine is an underground mine located near the town of Val-d?Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long hole stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23 Mt of ore, large blasts up to 1.8 Mt are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km radius of the mine site. In addition to managing mass blasts, means must also be found to mitigate the vibrations produced by the blast to diminish the disturbance to the neighbourhood. Therefore, the mine used numerous tools to properly plan the blasts and reduce the impacts. A program to control vibrations was one of the first tools put in place. The program?s aim was to draw up an action plan to ensure a follow-up of the homes by inspecting them. The second tool was to develop a methodology to plot a reliable attenuation curve and to adequately determine the maximum charge weight for each blast. Finally, effective communication tools were developed to inform the neighbourhood. There was a huge amount of work to be done in relation to the bench. Reliable and fast loading techniques had to be found to load large blasts in a very short period of time. Adequate logistics had to be developed to send underground more than 20,000 kg of emulsion per day while performing the daily underground operations. Technology had to be developed to adapt the i-kon electronic blasting system to large blasts. Since the control of the charges was the major factor to reduce surface vibrations, it was important to employ loading techniques that would permit decking of the long holes to reduce the charge weight per delays without adversely affecting the loading. All of this work requires an enormous amount of energy but also close collaboration between the different stakeholders (various departments, suppliers and consultants).

Jan 1, 2011

By Chris D. Thompson

In Southern Ontario, Canada, piles are frequently driven through competent clayey soils to obtain end bearing on extremely dense till or bedrock. One reason for this is the difficulty at assessing the adhesion of the clayey soils. This is illustrated by texts, such as the Canadian Foundation Engineering Manual, which is the standard of practice in Canada, that indicate that theoretical analysis of the adhesion values of such soils are unreliable. In this paper, the results of high strain dynamic testing have been used to estimate the shaft resistance of 11 closed end pipe piles driven in overconsolidated very stiff to hard clayey tills at four sites by means of the CAPWAP wave equation analysis. More than twenty-five years of experience with bearing capacity predictions by such means have developed considerable confidence in its accuracy. The results were found to correlate reasonably with the average Standard Penetration Resistances of the clays at the sites. There was a linear relationship between an adhesion of 64 kPa at 20 blows per 300 mm and 192 kPa at 60 blows per 300 mm. At one site, 6 piles were tested and found to have a wide range of Standard Penetration Resistance and estimated adhesion in the same stratum. While there was significant scatter of the results, piles would have been safe at design loads obtained from the relationships established by the analysis carried out for this paper after applying appropriate factors of safety.

Jan 1, 2002

By Paul Headland

The Washington Suburban Sanitary Commission (WSSC) has recently completed design for the Bi-County Water Tunnel Project. The project will include a 10-foot diameter, 5.3-mile long hard rock tunnel located within the Piedmont Physiographic Province in Montgomery County, Maryland. The rock formations present along the alignment are comprised of igneous and metamorphic lithologies. This paper presents the steps taken to characterize the complex geology along the tunnel alignment into a single ?Engineering Unit? based upon the intact rock and rock mass properties. The Rock Mass Rating (RMR) system is planned to be used as the basis for dividing the ground into three ?Excavation and Support? classes. This RMR approach was selected to establish contractual baselines as presented in the Geotechnical Baseline Report (GBR) and is intended to facilitate management of the ground support characterization during construction.

Jan 1, 2008

By D. E. Pollock, Andrew B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker’s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillars is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to pre-failure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25 to 40 percent higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Pre-failure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to improved designs as mines become deeper.

Jan 1, 2001

By D Brooks, S Gunn, T Perkins, J Siliezar

Ernest Henry Mining (EHM) is a copper, gold and magnetite mining and processing operation located 38km north east of Cloncurry. The EHM ore body has an average grade of 0.9% copper (chalcopyrite), 0.5g/t gold and 22% magnetite.Open pit mining commenced in March 1998, but EHM transitioned to underground mining in December 2012, extending the life of operations beyond 2024. The underground mine currently produces up to 3Mt/year of ore, hauled up a decline by truck. This figure shall double in 2014 with the completion of a 1000m shaft. The EHM Concentrator has a nameplate capacity of 10Mt/year. In June 2011, Xstrata Copper acquired the Mount Margaret resource to supplement underground production and utilise the full capacity of the Concentrator. The Mount Margaret Mining (MMM) operation was established to develop the five deposits making up the resource by way of open pit mining.Copper concentrate is produced by the EHM Concentrator via grinding, flotation and dewatering circuits. The grinding circuit comprises a SAG and ball mill in a closed AB configuration. Flotation consists of a rougher train, regrind and three stages of cleaning, with the tail from the first stage reporting to the tailings thickener.The mineralogy of the MMM ores is complex, comprising fine textures of active pyrite, copper oxides, native copper, clay and secondary copper sulphides. This paper provides an overview of the metallurgical test work completed to forecast the performance of the MMM ores through the EHM Concentrator and identify flow sheet modifications for maximising copper recovery and producing a saleable concentrate. A discussion of the challenges experienced in the plant to date follows.CITATION:Gunn, S, Siliezar, J, Brooks, D and Perkins, T, 2013. Adapting the Ernest Henry Mining concentrator to process the Mount Margaret ores, in Proceedings MetPlant 2013 , pp 347-370 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By J. T. Hollow

The Fort Knox Mine is located in Alaska?s interior, where the average ambient air temperatures range from -24°C (-11°F) in January to 16°C (61°F) in July. The mill processes a free-milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leaching, carbon adsorption and cyanide destruction kinetics. Additionally, an energy-balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy-balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy-balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post-project plant performance that validates the model and shows that the mine produced an additional 596 kg (19,155 oz) of gold while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By Sharpe E. J

The Triton lode is a schistose feldspar biotite chlorite rock with quartz, carbonate, pyrite and some pyrrhotite. Its more chloritic sections strongly resemble the enclosing greenstones, its more feldspathic portions are indistinguishable from the flne-grained phases of the porphyry dyke into which the southern extremity of the ore body merges. The ore body' has a length of 880 ft. and an average width of I2t ft.; in places this widens to as much as 30 ft.The average dip is 85° west and pitch of the ore shoot 75° south.METHOD OF SAMPLING.With the exception of a limited amount of channel sampling (a reference to which is made elsewhere in this paper) all the sampling is by chip sample.The samplers use a hammer weighing approximately 11 lb. and chip directly into the sample bags. Sampling is generally carried out over 3-ft. sections and portions thereof to the nearest half foot-thus a face 8t ft. wide is divided up into two sections of 3 ft. each and one section of 2 ft.-no measurements of less than 4 ft. are used and calculations are all in feet and dwt. per long ton.In the oxidised stopes wp.ere the lode is much narrower, .i.e., 6 ft., sampling is over 2-ft. sections. All borehole samples are over 2-ft. sections, this corresponding approximately to steel changes.(a) DEVELOPMENT SAMPLING.Driving.-This is done by following the east wall and each face is sampled-this corresponding to an advance of 5 ft. If the full width o,f the lode is not exposed boreholes...

Jan 1, 1938

By C. F. Weinaug, R. W. Farley, J. F. Wolfe

A rapid, accurate method for predicting the dew points of gas condensate systems and their subsequent normal and retrograde phase behavior with pressure decline has been developed. The method predicts dewpoint pressure, volume percent liquid, condensate content of produced gas, and the liquid and gas compositions at pressures below the dewpoint pressure. Use of a modified form of the BWR equation of state, which was established by regression calculations on experimental data from several gas condensates, provides depletion behavior predictions that are significantly improved over predictions using K-values based on convergence pressures and Standing's correlation for density. INTRODUCTION Prediction of complex hydrocarbon-mixture thermodynamics is fundamental to reservoir and gas process engineering. In particular, accurate descriptions of phase behavior are needed to plan production operations for gas-condensate reservoirs. Although analysis of reservoir behavior during producing and cycling operations can be made for simple reservoir models, extensions of these studies to more complex reservoir systems are still difficult, both with regard to numerical techniques and the phase behavior of the fluids. This report presents a mathematical method for handling the complex phase relationships encountered in retrograde condensates; it represents an advance in reservoir behavior technology in that it will aid the development of closed-form mathematical representations of total production systems. A typical phase diagram for a complex hydrocarbon mixture is shown in Fig. 1. When the reservoir temperature T, is higher than the critical temperature Tc, and lower than the critical-condensation temperature Tct' the mixture is a gas condensate. Decreasing the pressure on a condensate while maintaining nearly constant temperature will result in two phases forming at the dew point. Further decrease in pressure will cause additional liquids to be formed. This phenomenon is called retrograde condensation. As pressure continues to decrease, normal phase behavior regions are encountered (liquid vaporizes as the pressure decreases) until the low-pressure dew point is encountered. When a gas-condensate reservoir is produced, gas is withdrawn and the volume of fluids in the reservoir remains nearly constant as the pressure declines. Heavier components tend to accumulate in the liquid phase as a result of retrograde condensation, while lighter components tend to concentrate in the vapor phase. Thus, as the gas is produced the composition of the gas and the condensate

Jan 1, 1970

By G. L. Dollinger, J. P. Kindsvater, J. A. Gibson

DESIGN AND DEVELOPMENT OF A MOBILE MINING MACHINE INTRODUCTION Until recently, developing tunnels in hard rock has been accomplished either by the drill and blast method or by using large tunnel boring machines. Combining the flexibility of drill and blast with the safety, efficiency and productivity of a TBM has been the objective of mining machinery producers for many years. In 1979 The Robbins Company began developing a new type of tunnel boring machine called the Mobile Miner to meet these objectives. The development and testing of the Mobile Miner is the subject of this paper. CURRENT MINE DEVELOPMENT METHODS Both the drill and blast method and the use of a TBM have notable advantages and disadvantages. The drill and blast method, for example, allows much more flexibility, requires less setup time and has a lower initial cost than a TBM; however it requires the use of high explosives and blasting has a disrupting effect on the rock surrounding the development. A TBM, on the other hand, is safer to operate, more efficient, more productive and produces smooth tunnel walls without disturbing the surrounding rock. In longer straight drifts it will easily out distance the drill and blast method. The TBM, however, is limited to boring a circular cross section tunnel which must then be modified if a flat floor is required. It also has a higher initial cost and an extended setup period.

Jan 1, 1985

By U. Dillon, G. Blackwell

"Geographic information systems (GIS) provide an efficient means for the recording, manipulation, revision, display and analysis of spatially referenced data. GIS are widely used at the exploration stage of mine development, and are increasingly used for reclamation planning. The ability of a GIS to perform spatial searches and query spatially referenced data make it a powerful tool for use at all stages of mine development. As the amount of data available for analysis increases, so does the power and flexibility of GIS as a planning tool.Starting from the exploration database, this paper describes how a GIS can be used for the development of mining plans based on topography, geology and mineralization information stored in a relational database. Planning decisions approaching the optimal can then be made for a wide range of parameters, including stockpile and waste dump locations, the location of potentially acid generating and neutralizing material for dump design, profitable and risk-controlled mine extraction sequencing, and haul road locations. This is made possible by the overlay and buffer analysis capabilities of a GIS which are explored and exploited to produce a continuous mine production planning program, as well as site remediation and reclamation using a successful case study. IntroductionGeographic information systems (GIS) are a relatively new tool in the mining industry. Although they have existed for a number of years, the potential of GIS for mine management and planning is only beginning to be investigated and exploited. The unique spatial capabilities of GIS make them particularly wellsuited for use in mining, where spatial information is fundamental to the processes of mineral exploration, mine development, and environmental reclamation. A number of potential applications for GIS in the mining industry have been identified, and they are widely used for exploration and reclamation. The use of a GIS as a platform for the development of mine planning routines and software remains an interesting, but as of yet unexplored, application of this technology."

Jan 1, 2003

By S. Asokan, D. Rathod, Ch. V. G. K. Murty

Tata Steel, a steel arm of Tata Group, is Asia's first and India's largest integrated private sector steel company. Tata Steel’s turnover in fiscal 2004-05 was nearly US$ 3.25 billion. As part of its vision to grow in related industries, Tata Steel is poised to enter the Titania businesses in the Indian state of Tamil Nadu. The Titania project will involve mining, separation of ilmenite & other co-minerals, beneficiation of ilmenite to synthetic Rutile and further maximum value addition to Titanium metal. This paper outlines the journey from the concept to current findings of the Bankable Feasibility Study in developing Sattankulam Heavy Mineral Sands Deposits in the State of Tamil Nadu, India by Tata Steel.

Jan 1, 2005

By B. Leong, H. Joubert

Keywords: Pyrometallurgy, furnace, auxiliary equipment, copper slag launders Pyromet has designed copper launders for tapping slag. What makes Pyromet?s launder design innovative and safe is that it does not have any cooling water channels underneath the launder runner, whilst achieving effective cooling of the runner. If matte burn-throughs were to occur through the launder runner, the risk of damaging water channels and the risk of explosions are reduced. In addition, since the cooling water channels are not harmed, the launder is easily repairable and reusable. Pyromet makes use of Finite Element Analysis to optimize the launder geometry to ensure that sufficient energy is removed from the centre of the launder. Factors considered during the launder design include the suitability of the geometry to the client?s needs, experience from existing installations, and ease of fabrication. Pyromet goes so far as to develop procedures for fabricators to ensure that fabrication issues do not compromise the functionality of the launder. When launder orders are received by Pyromet, the entire fabrication process and the functioning of the launders during operations are monitored to ensure that the launder designs are continuously improving with every installation.

Jan 1, 2006

By Geoffrey Fosbrook, Donald Phillips, Anil Parikh

The Second Avenue Subway is a $16.8 billion project planned by the Metropolitan Transportation Authority (MTA) in New York City. It will reduce overcrowding and delays on the Lexington Avenue Line, improving travel for both city and suburban commuters, and improving access to mass transit for residents of the East Side of Manhattan. The project is a new, two-track, 13.5 km (8.5 mile) subway extending from Lexington Avenue at 125th Street in Harlem on the north end of Manhattan, to Water Street at Hanover Square in Lower Manhattan. The first phase of construction includes rock tunnels from 92nd Street to 62nd Street and connection to the existing 63rd Street station, three new stations, and track and systems from 105th Street to 63rd Street, allowing service between 96th Street and Brooklyn via an existing Broadway Line. The following describes the Project in detail, discusses the construction challenges addressed in the design, and the initial design/build contract to be awarded in 2005. A discussion of the planned mined construction of two rock caverns and a cut-and-cover station construction are also included.

Jan 1, 2005

By Ed D. Thimons, Douglas E. Pollock, Andrew B. Cecala, Gregory J. Chekan, Jay F. Colinet, John A. Organiscak

Researchers at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) work to reduce respirable dust exposures in mining operations. One focus of this research is silica dust control for surface and underground operations in the metal/nonmetal mining industry. PRL researchers analyze dust sampling results from the Mine Safety and Health Administration (MSHA) to identify high-risk occupations to guide research efforts. Research is then conducted in an effort to improve existing technologies and/or develop new controls for reducing worker exposure to airborne silica dust. During the last few years, PRL researchers have conducted research related to the following goals: improving protection provided by enclosed cabs on mobile surface mining equipment, reducing dust generation from surface drills, reducing dust levels in iron ore operations, and developing a new method to clean dust from workers’ soiled clothes. A description of each of these controls and subsequent dust reductions quantified through site surveys will be provided.

By Clarence Karr

AN EXTENSIVE characterization was conducted on the neutral oil components in a low-temperature bituminous coal tar. A total of tai individual compounds identified with respect to individual isomers, and at least 55 other compounds were indicated to be present. The amounts were determined in all instances. A comparison of isomeric distribution in the tar with thermo-dynamic equilibrium distribution, and kinetic distributions indicated that the composition of the tar largely reflected the structure of the coal from which it was formed. Detailed descriptions are presented for the separatory and qualitative and quantitative procedures for the characterization of the neutral oil component. These include micro fractional vacuum distillation, displacement liquid chromatography, gas-liquid chromatography, countercurrent distribution, and infrared and ultraviolet spectrophotometry. Descriptions are given for the synthesis of authentic specimens of alkylindenes, The ultraviolet and infrared spectra of 134 polycyclic compounds, ranging from alkylindenes to alkylphenanthrenes, either found in the distillable neutral oil, or thought likely to be present, are also given.

Jan 1, 1967

Interest in the potential use of high-density, thickened tailings has recently increased significantly. Reasons for considering this new technology vary across projects, but commonly include the need to conserve water, perceived lower risk of catastrophic failure, potential easier closure, or even reduced overall costs. As with any new technology, there has been some tendency to overstate its potential benefits. This paper reflects on whether or not the potential benefits that have been attributed to paste and thickened tailings have been realized. Using a grading system, thirteen benefits that were ascribed to the new technology some years ago are evaluated. Data is taken from case studies, and it is suggested that the key proven benefits appear to be reduced operating costs in some cases, reduced wall-building costs, and reductions in water consumption. One key potential benefit that has not been universally achieved is a reduction in the footprint of the tailings facility. Reports in the literature highlight the sometimes confusing nature of trade-off studies. Unless full life-of-mine costs are considered, these studies can be misleading and incorrect. The need to establish a consistent basis for comparative studies is discussed.

Jan 1, 2012

By M. Jeffrey

This study investigated the elution of precious and toxic metals from activated carbon. Gold and mercury are of primary interest, due to their value and environmental impact respectively. A laboratory elution rig was commissioned to simulate industrial Zadra and AARL carbon elution conditions. Mercury was found to elute most effectively in strong caustic cyanide solutions; gold was found to elute most effectively in hot low ionic strength solutions. As cyanide decomposes on contact with activated carbon at high temperatures, optimum elution conditions for gold conflicts with those for mercury?no practical compromise in conditions was found. However, sequential elution allowed reasonable recovery of both metals. Ongoing work is looking at the deportment of other metals under elution conditions.

Jan 1, 2009

In the course of work being carried out in the Lubricants and Bearings Section of the Council lor Scientific and Industrial Research on the production of copper4ead 'bearings for 'use in aircraft, it has been found necessary to develop special metallographic methods. For proper control of the production of steel-backed copper-lead bearings it is necessary to adhere to rigidly controlled conditions, and it is essential that a method of examination be adopted which will readily detect actual defects or any variations in quality. Some defects can be observed with the naked eye, whilst others are detected by radiographic examination. This latter method is invaluable as a rapid, reliable test in the production of aircraft bearings, but it is necessary to observe the structure of the alloys under the microscope, both to be able to interpret the radiograph correctly and to determine what has occurred to the metal during and after solidification. The use of a sound metallographic technique is'particularly important in developmental work and research connected with these bearings.Polishing TechniqueCopper and lead are practically immiscible in the solid state, but whilst they are miscible only in certain limited proportions in the liquid state; consequently "alloys" of copper and lead consist of a mixture of the constituent metals. The metallographic difficulties are obvious. Copper is a relatively tough metal, although it readily scratches, whilst lead is extremely soft and easily deformed. It wouId be expected if any normal polishing technique were applied that the lead would be readily torn out of the surface being prepared, and, in addition, that the lead would tarnish very easily.Grange(2) has described a method by which these difficulties can be overcome. The method involves an etch-polish procedure using "chrome regia" as an etchant for the copper. The chrome regia was a solution of chromium trioxide and hydrochloric acid in water. This type of etchant has been adopted, but it was found necessary to make certain changes.The method now adopted in this laboratory is as follows: The specimen (which is usually mounted in bakelite) is wet ground in a series of successively finer Hydro-Durexsil emery papers down to 60.0· grit paper.The specimen is then etched in the chrome regis, etchant (the composition of this etchant will pe discussed later) for approximately five seconds.Most efficient etching is obtained by swabbing the surface of the specimen...

Jan 1, 1944

By G. E. Perry, R. D. Seba

The steam soak process is the most widely applied and most successful thermal supplemental recovery process in use today. This process, which consists of injection of steam in various quantities into a well that is subsequently used as a producer, can be repeatedly applied to the same well. The treatment, if successful, will increase the production rate of the well for a given period. For this reason, the steam soak process should be considered primarily as an acceleration method rather than as a method for producing oil that could not be recovered by primary means. However, application of this process to reservoirs containing viscous crude may produce oil that otherwise would have zero present value or would be produced at such low rates by primary methods that it would not be profitable. A major necessity for the successful application of the steam soak process is a source of natural energy. This source of energy may exist in one or more of the following forms: expansion of fluids, compaction, gravity drainage. This study was undertaken to determine the effect of gravity drainage on steam soak production and recovery and to develop a method for predicting production rates, ultimate recovery, and heat requirements when applying this process to a reservoir in which the primary driving mechanism is gravity drainage. (For additional discussion of some of the factors that affect recovery of viscous oils by the steam soak process, see Ref. 5.) Model The model developed for analyzing the performance of the steam soak process in gravity drainage reservoirs is a modified form of that developed by Matthews and Lefkovits.1,2 The model used in this study consists of two concentric cylindrical volumes of productive formation with cap and base rock of impermeable material. The inner cylinder, extending from the radius of the wellbore to some predetermined radius, is referred to as the hot zone; and the outer cylinder extending from the exterior boundary of the hot zone to the outer drainage boundary will be referred to as the partially heated zone. Fig. 1 is a schematic cross-section of the model, indicating its thermal properties. Horizontally the reservoir is divided into two regions, the upper region having a high gas saturation and residual liquid saturation, and the lower region containing a high liquid saturation. The boundary between these two regions is referred to as the free surface, which drops and changes shape as fluid is produced from the reservoir. The model was used to analyze the steam soak process by applying the following assumptions: 1. The horizontal formation is composed of one or more homogeneous noninterconnected layers containing incompressible fluids. Each layer is treated separately. 2. The hot zone is heated by the initial soak and is maintained at the steam temperature corresponding to atmospheric pressure by resoaking. 3. The height of the free surface at the producing well is at all times zero (producing well is pumped off). 4. The position of the free surface at the start of

Jan 1, 1970