Search Documents

By P. R. Tisot

Structural response and/or deformation was determined for each of four different grade Green River oil shales (27.0-, 34.5-, 45.5-, and 63.5-gal/ton) as they were heated in an inert atmosphere, under constant compressive stress, from ambient to subretorting temperatures; that is, below those required for rapid pyrolysis of the organic matter. Small cores and small columns of confined fragments comprised the test specimens, which were heated, in a specially designed microunit, at a uniform rate either to 725° or to 825° F under three different stress levels, 80, 200, and 325 psi. Structural response of some cores was observed as they were heated in a stress-free environment. The obtained stress-strain-time-temperature relationships provide information regarding the oil shale's yield temperature, yield stress, rate of compressive strain, loss of mechanical strength, and nature of structural deformation. Effects of structural deformation on induced permeability in small columns of fragments are presented. Results indicate that underground retorting of Green River oil shale may be seriously impaired through loss of induced permeability brought about by structural deformation of rich oil shale under the influence of heat and compressive stress.

Jan 1, 1971

By G. J. Hundman

Control of respirable dust produced by auger type continuous mining machines is normally attempted by water sprays from fixed nozzles mounted on the frame of the machine. In tests conducted under this contract, a 'wet auger' system was used, where the spray nozzles were mounted on the rotating auger itself. The tests were conducted at the Hunter mine of Smith and Stover Coal Company using a Jeffrey 1.00L auger miner. Operating the mining machine in the wet auger mode, it was found to produce 47 pct less respirable dust than when the fixed conventional sprays were used. On section dust levels were reduced too 3.5 mg/m3 which is equivalent to approximately 2.0 mg/m3 for a full shift portal to portal sample. The major difficulty that had to be overcome was the development of a simple reliable water transfer mechanism to get the water into the rotating augers. This was successfully achieved by the development of a water-through-the-shaft water system. This system can be retrofitted to existing machines and is available in kit form.

Jan 1, 1977

By Steve Kral

Commodity price down cycles are a fact of life in the mining industry. And companies pre-pare for them as best they can. Evenso, operations are still curtailed or closed during those cycles, profits shrink, layoffs are inevitable and many companies do not survive. However, one of the few good things that occurs during down cycles is the new, innovative exploration, mining and processing technologies that come about during hard times. To survive the lean times, the mining industry turns to improved technology to decrease costs and hold the bottom line. And, because mining is a cyclical business, each down cycle brings about technology improvements that carry over into the good times.

Jan 1, 2004

By W. J. Birch, R. Farnfield

The use of electronic detonators to control blast vibrations has been previously established by many authors. This is performed by determining the optimum delay period between the blast holes for a particular pattern that can accurately control the firing frequency of the blast, which in turn has a direct bearing on the frequency composition of the ground vibrations recorded at a particular location. This was established by Pedgen, Birch, Hosein & Farnfield (2006) whereby like-for-like comparison tests between non-electric and electronic blasts were carried out in a limestone quarry in northern England. They demonstrated that resulting peak particle velocity values recorded at near and mid-field distances were primarily a product of the firing frequency of the electronically initiated blasts.

Jan 1, 2009

By M. A. Reyes, L. Yan

Heat and humidity buildup within refuge alternatives (RAs) may expose occupants to physiological hazards such as heat stress. The Mine Safety and Health Administration (MSHA) regulations require RAs in underground coal mines to provide a life-sustaining environment for miners trapped underground when escape is impossible. RAs are required to sustain life for 96 h while maintaining an apparent temperature (AT) below 95 °F (35 °C). The National Institute for Occupational Safety and Health (NIOSH) tested a 10-person tent-type RA, a 23-person tent-type RA, and a 6-person metal-type RA in its underground coal mine facilities to investigate the thermal environment over a 96-h period. The test results showed that mine air and mine strata temperatures surrounding an RA occupied by simulated miners (SMs) increased over the 96-h test period. The test results suggest that RA manufacturers should consider this increase in temperatures when calculating and evaluating RA components during surface and laboratory tests. The findings can equip stakeholders with additional considerations for calculating the interior heat and humidity temperature profiles for occupied RAs not tested in situ

Nov 22, 2019

By David Winter

The geotechnical design, construction, and monitoring aspects of a tied back excavation 85 feet deep in Seattle, Washington are presented. The excavation was completed in overconsolidated deposits of sand, silt, and clay. Lateral soil pressures used in shoring wall design were the lowest to date for an excavation of this size in Seattle. Instrumentation data collected from hydraulic load cells and inclinometers were analyzed and are discussed. The data suggest the actual soil pressures felt by the wall were lower than the design values. Recommendations for future study, as well as future design modifications are given.

Jan 1, 1987

By R. L. Wiegel

Several mineral process modeling and simulation packages are currently available for use in evaluating the performance of alternative process flowschemes. A critical link that has been missing from these packages is the ability to quantitatively model the effect of size reduction on the liberation of the valuable and waste minerals in the ore being processed. Although there have been several approaches taken to this problem over the past 25 years, none has led to a satisfactory conclusion. A technique has been developed for measuring the effective liberation characteristics of magnetic taconite ores, and a program has been constructed which makes use of these liberation characteristics in simultaneously simulating both size reduction and mineral liberation as it occurs in tumbling mills. This is an especially important step in the modeling of magnetic taconite processes, where magnetic rejection of low grade wastes between grinding stages mandates that a predictive capability be available. The current application is specific to magnetic taconite, but it is possible that a similar approach could be used for other types of mineral systems.

Jan 1, 2002

By A. C. Johnson

This circular is one of a series published by the Bureau of Mines describing mining and beneficiation methods and costs at various mining operations throughout the United States. Inclusion of the Abbott mine in this series is of particular interest, as the complex geology and the character of the deposits make their exploitation a unique operation. The mine operates on a high-cost, comparatively small-scale basis, and only the persistence of an aggressive management has enabled it to maintain its rank among the major mercury producers of California. Rising costs and decreasing metal prices, which continuously threaten the low profit margin, are reflected in increased efficiency of operation. This report summarizes past operations and describes, in detail, the geology and ore deposits; exploration and mining methods; and furnacing and condensing operations. It covers the entire operation from initial exploration to the actual production of mercury. Comparative production costs for 1944 and 1958 are of special interest.

Jan 1, 1962

By David G. Winter

The Olive 8 excavation site in Seattle was surrounded on three sides by conditions requiring innovation, careful modeling, and extensive instrumentation to support use of a first-of-its-kind shoring system. The solution combined heavy soldier piles, long and steeply angled tieback anchors, and tightly spaced soil nails to support surcharge loads from a 33-story adjacent tower separated by a narrow alley housing critical utility lines. Land restrictions on two other sides of the site also required innovative applications of traditional methods. The Olive 8 project has won three state and local awards for innovation and has been reported on in Engineering News-Record and has been the subject of two feature articles in the Seattle Daily Journal of Commerce. This paper presents the conditions and site challenges, reviews the design analysis, discusses the shoring performance, and looks at other potential applications.

Jan 1, 2009

By S. C. Tadolini

Roof support systems have evolved from standing posts and timbers to a generation termed ?big nails? where steel bars are inserted into boreholes and anchored with expansion shells and/or resin cartridges. These systems have been effective but are limited to mining height. Additionally, the properties of steel do not resists shear forces or have the flexibility being required in difficult ground conditions. The next generation of roof support systems is coupling the best parts of the ?big nail? and resin grouted cable bolt systems. This paper will present the advanced technical solutions of the next generation of cable systems that includes an indented high-capacity PC-strand used with a variety of fixtures. Case histories of support applications will be presented.

Jan 1, 2012

Particles of a complex nickel sulphide concentrate (containing pyrite, pyrrhotite, pentIandite, and violarite as the major mineralogical constituents) were entrained in a stream of hot gas the temperature of which was varied from 500 to -1000°C. Chemical analysis of the particulates collected from the furnace was used to detect the rapid change in sulphur content which accompanied the ignition temperature jump. X-ray diffraction analysis was used to characterize the oxidized material.These techniques showed that ignition was dependent on the mineralogical composition and occurred over the temperature range 500-900°C. Pyrite ignited first in the range 500-600°C; pyrrhotite was the least reactivemineral and required temperatures in excess of 800°C for ignition. The nickel minerals <pentIandite and violarite decomposed before ignition and ignited at temperatures intermediate to those required for the pyrite and pyrrhotite. The ignition temperature for the pyrite was found to be independent of particle size and concentration of oxygen in the atmosphere.Ignition temperatures determined by the simulated flash smelting method were compared with the results of differential thermal analysis (DTA) measurements performed on the same concentrate. Temperaturesdetermined in the DTA test as corresponding to the start of exothermic activity were shown to be at least 100°C below those determined by the simulation test.

Jan 1, 1978

By Karl A. H iggins, James P. Racine

"Displacement Cast-in-Place (DCIP) piles are not a common deep foundation type in the Washington, DC Metro Area market. As a result, less regional data is available for these foundations compared to other alternate deep foundation types. Displacement cast-in-place piles (DCIP) differ from traditional Auger Cast-In-Place (ACIP) piles in that the pile annulus is formed by pushing a partially-flighted, auger bit to depth via a large mandrel. The auger bit includes a displacing body near the bottom of the tooling. Therefore, little to no spoils are generated during installation and the soil around the annulus is largely densified in-place due to the displacing body being slightly larger than the mandrel it is attached to.Due to this densification, one would expect that the theoretical DCIP capacities (compression or tension) would be greater than an ACIP pile (assuming a pile of similar length and diameter). After 20 static load tests and the installation of over 6,000+ piles on the MGM National Harbor Casino Project, the differences in pile support characteristics between DCIP and ACIP piles of same size and depth was small. The performance of both pile types depended on the density and type of soil within the bearing stratum. In some early cases of DCIP use, the performance exceeded expectations and appeared to be more in line (or better) than typical capacities obtained from driven displacement piles. Other times, the tip elevations could not be achieved or were so difficult to achieve that installation delays occurred and/or significant additional engineering effort was required to address piles short of their requirement embedment.This paper will discuss the limitations of DCIP pile installation in dense Coastal Plain soils and will present the lessons learned during this project. The paper will also compare the DCIP pile type to both conventional ACIP and driven displacement piles utilizing regional and site-specific load test and installation data."

Jan 1, 2017

The production of sulphuric acid at Port Pirie by the contact process began in March 1924 with the commissioning of the Electrolytic Zinc Co.'s roasting and acid plant. This plant, operated by B.H.A.S. Pty. Ltd. on behalf of the E.Z. Co., continued to produce sulphuric acid from the gases evolved when roasting Broken Hill zinc concentrate in mechanically rabbled furnaces until September 1954, when the plant was closed down.In this peri9d of approximately 30 years some 600,000 mono tons of 98·5 per cent sulphuric acid was produced, most of which was used for fertilizer production at Wallaroo and Port Adelaide. During World War II 14,400 mono tons of the above was produced in the form of 20 per cent Oleum and railed to the Salisbury Munitions Factory for use in the production of nitro-glycerine, gun-cotton and T.N.T.In the early post-war period various ways of converting at least some of the sulphur in the gases' discharged to atmosphere from the lead sintering plant were considered until, in 1949, it was decided to erect a modern contact acid plant. Much work remained to be done on the roasting plant to produce a gas of suitable grade for the contact process and also on the design of a purification section suitable for the treatment of D.L. gases.The acid section itself, however, was largely of conventional design and it was therefore decided that this would be erected first. To it was then attached a sulphur-burning section to allow it to operate as a "hot gas" brimstone acid plant until the roasting and gas purification plants had been designed and erected. In this way the urgent need for sulphuric acid in the fertilizer industry would be relieved, to some extent at least, as soon as, possible.

Jan 1, 1956

Barrick Gold plans to have four new gold mines in production by 2006. Together, the mines would increase the company’s output by 40 percent. The projects include Veladero in Argentina, Alto Chicama in Peru, Cowal in Australia and Tulawaka in Tanzania. All of them are scheduled to begin production between the first quarter of 2005 and the first quarter of 2006. They are expected to drive Barrick Gold’s growth profile to a target of 211.5 to 217.7 t (6.8 million to 7 mil-lion oz) of gold production in 2007. The company’s projected output for 2004 is 152.4 to 155.5 t (4.9 million to 5million oz) in 2004. Overall, higher production and lower costs are expected in the early years from the new mines.

Jan 1, 2004

By R. L. Fullman, J. W. Cahn

A method is derived for obtaining the distribution of sphere diameters and plate thicknesses (or pearlite spacings) from size distribution functions obtained along randomly oriented lines. The method described offers several advantages over existing methods. IT is often of interest to measure not only the average particle size but also the distribution in sizes of particles dispersed in an opaque material, such as an alloy. Particles of a single size will exhibit a range of apparent sizes on the plane of polish. If the sample contains a distribution of particle sizes, the distribution of observed sizes on the plane of polish is related to the distribution of actual particle sizes by an integral equation, For example, a distribution of sphere sizes, N(r),

Jan 1, 1957

By C. Keefe, O&apos

Measurements of the quantity of entrained air within processes have challenged instrumentation developers for years. This is particularly true in the unique and demanding operating environment and applications seen in minerals processing. In minerals processing applications, entrained air plays a role in errors seen within nuclear density gauge measurements and in pumping efficiency. It is also the major component of flotation processes. The measurement of the quantity of entrained air, known as the gas void fraction, can now be performed from the outside of a process pipe through CiDRA?s patented passive sonar array-based technology. Within column cells, the need for a robust, no maintenance, accurate means of measuring the entrained air, known as gas holdup, has resulted in a submersible version of this technology. CiDRA?s meter technology calculates the gas void fraction by first measuring the speed at which naturally occurring sound in the process slurry propagates past an axial array of sensors. These sensors are incorporated in a band that is wrapped around the outside of the pipe, resulting in no process downtimes for installation and unprecedented reliability. A known relationship between this speed of sound and the entrained air captured in the form of bubbles within the slurry is then applied in CiDRA?s meter to calculate the gas void fraction. This paper will present the measurement technology, its operation, its calibration and its application in a variety of gas void fraction and gas holdup measurement situations such as pumping efficiencies, hydrocyclone operation, external sparging, and column cells.

Jan 1, 2008

It is easy to demonstrate the importance of aggregates in any conversation about infrastructure and other engineering artefacts. Peoples around the world have made use of stone to enrich and enhance their lives since the earliest days of civilisation. In New Zealand, Maori used hard durable rocks for weapons, tools, and basic structures. European settlement accelerated the use of quarried materials and formed the basis for development of our society as we see it today. Logic might suggest that the quarrying sector would be recognised positively for, and encouraged to continue to contribute to, this underpinning of the way we are. The reality is æNot In Most Back YardsÆ. Why? The rock is where it's always been (often overlooked) and our æsocialÆ environment is today's hard place. For a resource-based business in New Zealand, that environment is principally the Resource Management Act, with the widespread power it has distributed to anyone prepared to invest their time. This coupled with a lack of leadership and direction in the implementation of the Act has created a climate that stifles development and diverts energy and resources to æplaying the gameÆ rather than ælifting the gameÆ. Perhaps the real costs of this are not yet widely recognised. The paper will draw mainly on the experience of endeavouring to consent a ægreenfieldÆ quarry in the Waikato region. This is supported by commentary based on nearly 10 years of ælivingÆ with the RMA at sites across much of New Zealand. RMA Scorecard Summary: Effects based? Rarely. Level playing field? No. Maori Consultation? Could do better. Efficient use of resources? No. Timely? No. Is it working for other sectors? Certainly not the quarrying industry's customers and end users.

Jan 1, 2000

By H. J. de Haan, J. van Lookeren

In view of their size and favorable characteristics, Shell's heavy-oil fields on the eastern coast of Lake Maracaibo, Venezuela — known as the "Bolivar Coast" — are obvious candidates for the application of thermal recovery methods. During the last decade various methods have been tested, such as steam drive,', steam soak and in-situ combustion.3 Steam soak was discovered as a promising production method rather accidentally in 1969, during early steam drive testing in the Mene Grande Tar Sands1 When steam erupted at the surface due to breakdown of the overburden, the injection wells were back-flowed to relieve the reservoir pressure. This resulted in high oil production rates, all the more impressive because the reservoir is unproducible by primary means. It was concluded that injection of limited amounts of steam might be a very effective method for stimulation of heavy-oil wells. To obtain information that would be more widely applicable, testing of the process was continued in the eastern part of the Tia Juana field (Fig. 1). Here even more favorable results were obtained than in Mene Grande. This created sufficient confidence to prompt a large-scale project, which was considered essential for an adequate evaluation of ultimate recovery, steam requirements, mechanical problems and economic prospects. To obtain an early answer on the ultimate recovery a fairly depleted area was selected in the western part of the same field ("A" in Fig. 1). The first steam was injected in March, 1964. This paper describes the performance until the end of 1966. The production mechanism and well inflow performance are discussed in some detail. In view of the favorable results obtained so far, steam soak operations have expanded considerably since the start of this project. Presently, five other projects are under way, of which two are about the same size as the one under discussion, with further extensions being programmed. Description of the Project Reservoir Data Shell's part of the Main Tia Juana reservoir has a proven area of 8,800 acres and an average net oil sand thickness of 130 ft. It contained an initial quantity of 2,750 million bbl of stock tank oil (STOIIP), with an API gravity ranging from 10 to 15 API and a viscosity of 100 to 10,000 cp (at 122F). As a geological unit it is known locally as the Lower Lagun-illas member of the Lagunillas formation, which is early Miocene in age. The sand bodies are believed to be distributary channel sands deposited in a lower coastal plain. Most of the channel sands have lateral and some vertical communication. The field was developed mainly in the period from 1936 to 1950. The ultimate primary recovery is estimated at 18.1 percent of STOIIP, of which 12.5 percent STOIIP had been produced by the end of 1963 from some 540 wells. By then the average pressure had decreased from an initial value of 960 to 550

Jan 1, 1970

Neutralization with lime is a simple, cheap, and effective means of treating acid raffinates from uranium processing to' raise the pH, reduce the concentrations of dissolved salts (including heavy metal impurities), and remove amine by adsorption. Two-stage neutralization, using limestone in the first stage at approximately pH 4 and lime in the second, lIlay be advantageous.Lime neutralization of mffinates in the pH range 7 to 8· 5 generally reduced the radium ·concentration to 10 to 200 pCi 1-1, but ·there was considerable scatter in the experimental data. The radium concentration was further reduced to less than 3 pCi 1-1 by co-precipitation of barium (radium) sulphate with 10 mg Ba (as barium chloride) per litre of raffinate. Adsorption of radium on barytes was -also effective in reducing the radium concentration in neutralized raffinate to less than 3 pCi 1-1.The radium concentration of pit water was readily reduced to less than 3 pCi 1-1 when pit water containing 0·01 M sulphate as ammonium, calcium, or sodium sulphate was treated with 20 mg Ba per litre of pit water.Adsorption on barytes was also effective in removing radium from pit water containing 0·03 M sulphate.

Jan 1, 1975

By Michael J. Beus

This Bureau of Mines report describes a tunnel stress relaxation gage (TSR) developed to measure initial radial displacement around full-sized underground openings. The TSR technique was shown to be a valid concept in previous field verification tests. Sensitivity has been improved by employing a titanium alloy cantilever in the transducer head, which also permits a deeper sensor location. Use of improved fabrication methods such as stainless steel bellows and sputtering techniques and use of an environmental chamber for testing greatly increased overall reliability. A miniature data acquisition system (DAS) was interfaced directly to the transducer for increased versatility and containment entirely within a borehole. The present TSR system is suitable for use around full-size underground excavations, particularly machine-bored openings. Field evaluation of the improved instrumentation verified the design goals.

Jan 1, 1978