Search Documents

By Robert Vergie

Like most of you, I would rather work on a job than talk about it. But it is fruitful to spend some time taking stock of important developments in the heavy construction field. One of the strongest recent movements affecting the industry has been the push for safety. I regret that it is a recent development. Not that builders were against safety. Too often though, it was easier to continue with dangerous old work methods than to try something new. Too often, it was easier for equipment manufacturers to build production tools with little consideration for worker safety. And too often, accidents and gruesome disasters occurred. The ultimate result of on-the-job injuries in construction and other industries was the Federal Government's Occupational Safety and Health Act of 1970. Individual states were required either to accept OSHA or pass updated regulations at least as stringent as the Federal requirements. These new rules must be strictly obeyed -- not just because they carry civil and criminal sanctions -- but because they correct unsafe conditions and reduce hazardous acts. Though some OSHA measures have been criticized as superfluous, most of them do in fact save lives and limbs. Equally important, the tunneler who follows the new safety regulations can be fairly certain of an efficient, uninterrupted operation. Regulations do sometimes bring rewards.

Jan 1, 1974

By J. Moore, D. Gault, R. V. Lugn

Impact of small projectiles with velocities between 0.9 and 7.3 km per sec on basalt produce craters chiefly by the ejection of fragments. Weight-size distributions of the ejecta are linear for part of the size range of the fragments. Cumulative weight-size distributions of the ejecta from different craters vary because of erratic formation of large fragments and a large percentage of ejecta below 0.1 mm. In the range of velocities studied, the crater depth is approximately proportional to the 0.75 power of velocity of the projectile. This relationship may represent a transition regime between the fluid impact regime and the undeformed projectile impact regime. The volumes per unit of projectile energy of the craters produced are comparable to those reported for lower speed projectile impact and drill bits. An experimental investigation of projectile impact on rock is being conducted jointly by the Ames Research Center of the National Aeronautics and Space Administration and the U.S. Geological Survey. Projectiles are launched with light-gas guns at the Ballistics Range of the Ames Research Center. The craters and ejecta produced in these experiments are being studied by the U.S. Geological Survey. Steel, aluminum and polyethylene projectiles weighing from 0.25 to 0.015 g were accelerated to velocities of 0.88 km per sec (2,900 fps) to 7.3 km per sec (24,000 fps) with a light-gas gun, using hydrogen as the propellant medium. Projectiles impacted the targets normal to plane rock surfaces in an atmosphere of air with a nominal pressure of 25 to 50 mm of mercury. The metal projectiles were mounted in supporting four-piece nylon sabots, which guided the projectiles down the launching tube. After launch, aerodynamic drag acted to separate the sabots from the projectiles. Impact velocities were determined with time measurements and spark photographs of the projectiles in flight. Ejecta were collected in lucite and aluminum containers placed around the target block. A small hole in the containers permitted projectile entry. Impact of projectiles of the size employed produced craters in the rock targets chiefly by ejection of fragments. The craters are small, roughly conical depressions with crushed and intensely fractured rock at the bottoms of the depressions. The ejecta are composed of pieces of the projectile and rock fragments ranging in size from a few tenths of a micron or less to several centimeters in maximum dimension. In this paper, the structural features of the craters, the weight-size distributions of the recovered ejecta, and crater depth and crater volume relationships are described. DESCRIPTION OF CRATERS Typical craters (Fig. 1) produced by experimental projectile impact in basalt are shallow, wide base

Jan 1, 1963

By A R. Heath, I Arbuthnot

Feed slurries are typically flocculated in a thickenerÆs feedwell to increase the settling rate, underflow density and overflow clarity. High molecular weight polymeric flocculants are normally used, but present a number of challenges in terms of make up, dilution, delivery and mixing with the feed slurry.Various aspects of the flocculant dilution and delivery system have been studied with a combination of flow visualisation and computational fluid dynamics (CFD). An open topped flocculant dilution/mixing box has been developed to replace a conventional flocculant manifold, with improvements to the mixing, fault diagnosis and ease of determining the flow split to the various dosing points. The addition points to the feedwell have also been studied, both in terms of where the flocculant is added, and how. While conventional multi-hole spargers are effective in dispersing flocculant, they are prone to blocking and have been replaced by open-ended pipes. The required dispersion is provided by an efficient mixing element placed in the dilution port. Adding the flocculant into the feedwell dilution stream prior to mixing with the slurry also provides super-dilution of the flocculant that can further improve the flocculation process and reduce flocculant consumption.CITATION:Heath, A R and Arbuthnot, I, 2013. Advances in thickener flocculant delivery, in Proceedings MetPlant 2013 , pp 86-92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Dale Preece, Ayman Tawadrous

This paper presents a number of examples of three-dimensional blast modeling in both surface and underground environments that include time-delay explosive decking. These examples include: 1) quarry blasting, 2) coal seam protection blasting, 3) mineral mine blasting with high energy time delayed decks, and, 4) underground single-level/single-shot drawbell blasting.

Jan 1, 2014

The notes from which this paper has been prepared were set down at the time of the author's departure from Australia in 1935. Mr. Frank Forman, Government Geologist of Western Australia, who has very kindly read the paper in manuscript, affirms that the views here set forth are now accepted by most geologists. Thus, Forman's recent presidential address before the Royal Society of Western Australia (1937) mentions sediments in the Kalgoorlie Series "including banded jaspers and jaspilites."While it may, therefore, be superfluous to belabour the question further at this time, Mr. Forman has encouraged the author to publish this paper as a summary or both past and present views.To those specially interested in the subject of the paper, a study of pertinent Plates attached to Western Australian Geological Survey Bulletin No. 71, 1917, is suggested.The type of rock which is variously called "jasper bar," jaspilite, or "ferruginous quartzite" is familiar to all mining men who have worked in the West Australian goldfields.In its typical form it is a "striped" rock consisting of alternate layers of white or pinkish silica with red to brown bands of iron-bearing silica.In the course of geological work in many parts of Western Australia I studied exposures of jasper bar and was repeatedly impressed with the similarity of much of the material to the sedimentary "banded iron formation" of Canada. It was, therefore, a surprise to learn that the jasper bars were not generally regarded in Australia as sedimentary horizons. It is true that Honman offered convincing evidence of the sedimentary origin of the jaspers...

Jan 1, 1939

By William Paxton Hewitt

In the Santa Eulalia mining district, Chihuahua, Mexico, the main mineral zone occurs in a gently warped dome with simple associated structures and contains orebodies distributed through a vertical range of over 900 m. The stratigraphy of 1945 m of geologic column is described and an abrupt shrinkage is documented in the volume of limestones immediately associated with large orebodies. Termed collapse, this shrinkage occurred during the course of mineralization. Contacts of limestone with igneous sills, and 366 m of fossiliferous limestone beds, particularly the main fossil bed, have been important localizers of ore-bodies. Up-dip gravitational controls may have been important. Fractures have exerted only local controls and over short distances. Thrust zones have displaced diabase sills and in turn have been intruded by upper members of a group of rhyolite porphyry sills. Mineralizers were related to the rhyolite porphyry, and ore has been introduced to the limestone where certain sills lie between the displaced segments of diabase and have been cut by north-south fissures. Speculations are raised that fields of unreleased strain may have influenced orebody locations; the district's zoning pattern may be a reflection of the filtering effects of large volumes of limestone; and that metal-rich brines mobilized by or incorporated within the invading porphyry might be the source of the mineralizers. PRODUCTION AND LOCATION The Santa Eulalia district has a production record approaching or exceeding 35 million tons of silver-lead-zinc ore from replacement bodies in limestone. In operation since the first years of the 17001s, production has been confined to two intensely mineralized areas separated by 2 km of barren limestone, the West Camp and the East Camp. Probably 50% has been mined since 1908, with over 90% from the West Camp. The West Camp, exploited through a vertical depth of 1945 m and now approaching exhaustion, is the subject of this paper. The district lies in the northern part of the Santa Eulalia Mountains in central Chihuahua in northern Mexico, 400 km south of El Paso, Texas, and 22 km southeast of Chihuahua City. Dominating the northern part of the range is the Cerro de Santa Eulalia, a broad rolling upland which contains the district's West and East Camps. The West Camp, on the west side of the range, centers around the village of Santo Domingo, which is 2 km northeast of the Real de Santa Eulalia (Fig. 1). REGIONAL GEOLOGY Thick-bedded middle Cretaceous limestones, probably Aurora, form the great bulk of the Cerro de Santa Eulalia. These beds, warped into a gentle dome, are severed on the west by a faultline scarp and truncated on the north by the Dolores Pass, a wind gap that

Jan 1, 1969

Brunswick Mine employs an ore and waste pass system for material transfer. This paper reviews the evolution and performance ore pass systems at the mine. It presents the range of selected configurations, inclination, dimensions etc. Select case studies are used to address the influence of structure, stress and materials handling on the longevity of the employed ore passes.

Feb 1, 2008

By John P. Davis

The use of conventional, circulatory air rotary and fluid rotary, cased and uncased drilling methods in the vicinity of sensitive infrastructure can have deleterious effects on the ground conditions surrounding and supporting structures and the structure itself. Furthermore, the use of these conventional methods offers the engineer or contractor little information about the condition of the subsurface during geotechnical applications. Conversely, sonic drilling measurements and samples can be used to evaluate actual conditions during the progress of exploration and construction across a given site. This paper will discuss the history and properties of sonic drilling and explore case histories of geotechnical applications for the advancement of boreholes within vulnerable structures and on sensitive sites for several recent infrastructure projects ? a tunnel and railroad project, a dam grout curtain project, a bridge micropile exploration project and a tunnel instrumentation project. Project summaries will discuss the advantages realized when the application of sonic drilling techniques demonstrated superior accuracy, quality control, efficiency, productivity, penetrability, waste minimization and adaptability when drilling adjacent to or within existing infrastructure. Finally, the discussion will address the current testing and application of sonic drilling to the installation of micropiles, earth retention anchors, grout injection and instrumentation installation where the quality control benefits provided by the inherent soil cores, measurement while drilling systems, accuracy and non-destructive production drilling features will be advantageous.

Jan 1, 2006

By S L. Garwin

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Since the Eocene, New Guinea tectonics have been driven largely by the south-westerly-directed collision of accreted arc terranes with the northern margin of the Australian Craton, and subsequent westerly-directed transport of these exotic terranes by left-lateral strike-slip fault systems. The subduction of the Solomon Sea plate beneath north-eastern New Guinea in the mid- to late-Miocene led to magmatism and related gold-copper porphyry and epithermal mineralisation in the Maramuni arc and the formation of the Frieda River, Nena, Wafi-Golpu and other deposits.The development of the world-class porphyry and epithermal deposits in the Medial New Guinea magmatic belt, including Grasberg, Ok Tedi and Porgera, is localised by dilational zones formed about the intersections of north-easterly-trending, reactivated basement faults and north-dipping reverse faults related to the southward progression of the Papuan fold belt during the Late Miocene to Pleistocene. These deposits probably formed during short mantle-derived magmatic episodes in zones of regional isostatic uplift, which are attributed to the delamination of the lithospheric mantle beneath New Guinea.CITATION:Garwin, S L, 2015. The tectonics, geology and gold-copper metallogeny of New Guinea, in Proceedings PACRIM 2015 Congress, pp 151–164 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By G. Belzil, F. Robichaud, M. Fullam

"The Goldex mining and milling complex is operated by Agnico-Eagle Mines Ltd. and is located in the Abitibi greenstone belt of Northwest Quebec, Canada. The mill operates presently at a throughput of 8,250 tpd with gold grade varying between 1.8 and 2.2 g/t. The ore is very high in gravity recoverable gold (GRG) at about 92% and as such a significant emphasis was placed on the gravity circuit. Commercial production started in 2008. Average gold recovery is 93.5% with about 68% of gold recovery coming from the gravity circuit. Over the course of the first several years of production, several gravity audits were carried out. In 2009, a complete gravity audit was completed, including ore, classification, Knelson Concentrators, and the gold room. In 2011, an audit was undertaken of the flotation circuit to determine the efficiency by which GRG is floated. Large samples of flotation feed and tails were collected and process for GRG content. This allowed a link between gravity and overall recovery to be made. This paper presents results of the audits and the development of a model linking gravity and overall gold"

Jan 1, 2012

By Kumar A, Mishra N. C

For each tonne of chromite ore mined in Sukinda, approximately ten tonnes of fine overburden material is generated. The overburden typically contains about 30 - 60 per cent Fe2O3, 0.3 - 1.1 per cent Ni, four to nine per cent Cr2O3 and 0.04 - 0.2 per cent cobalt and is being discarded leading to loss of valuable metals and creating environmental pollution. In order to take the advantage of presence of iron, nickel and chromium, the present studies advocate the utilisation of nickel lateritic chromite overburden for production of Ni bearing pig iron through blast furnace extracting maximum iron and nickel from the chromite overburden. The present paper deals mainly with the beneficiation of chromite overburden, sintering characteristics and thermodynamic studies. The beneficiation study shows that a beneficiated concentrate having Fe - 50 per cent and Ni -- 1.1 per cent can be achieved from chromite overburden having Fe - 30 per cent and Ni -- 0.7 per cent. Sintering studies have been carried out with bed height of 300 and 450 mm at a suction of 600 and 900 WG respectively. The results reveal that good quality sinter can be produced from chromite overburden concentrate with a basicity of about 1.0 and coke breeze consumption rate about 16 per cent. In all the experiments, Tumbler Index, Abrasion Index and Shatter Index was found to be in the range of 65 - 70, 4.5 - 5.5 and 85 - 90 respectively. The other parameters namely softening temperature, melt down temperature, reduction degradation test and relative reducibility have also been determined. A thermodynamic analysis has also been carried out to make a technological assessment of the process for the production of alloyed pig iron from chromite overburden in blast furnace which shows that it is possible to produce nickel bearing pig iron in blast furnace using the sinter up to 80 per cent. Techno-economic analysis reveals that this route will yield a substantial profit even after accounting for cost of beneficiation, extra coke, raw materials and extra slag produced.

Jan 1, 1999

By Sun Shao Xian

The Port of Shekou is situated at Shenzhen Bay on the east side of the Pearl River estuary. Geological condition of the site is quite complicated. On top of the sea bed, there is a layer of soft silt 8 - 14 m thick. Under the soft silt, there are intercalated layers of sand, silt and clay. Average surface elevation of the underlying undulatory weathered bed rock is about - 20 m, with a variation of about 10 m. In certain locations, the weathered bed rock is covered with a layer of silt 3 - 4 m thick. This paper gives brief account of three types of wharf structures which are of particular interest, constructed in the last few years: (A) Platform type wharf structure with frontal sheet piling and steel raking pile in the rear; (B) Relieving Platform type structure with steel sheet piling and inclined anchoring HP pile ; (C) Steel pipe pile row supported apron added to a marginal quay. Average construction time of a deepwater berth is about six months.

Jan 1, 1991

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

By Gunderson C. T

The use of carbide tipped integral drill steels and detachable bits is discussed in relation to the means of drilling or cutting employed. It is stressed that only by correct use can the full value of these tools be realised.Factors affecting carbide quality, the design of shanking steels and the requirements and techniques of brazing in inserts are considered.It is essential that the brazed jointing between carbide and steel be strong but ductile. The methods used for the manufacture of carbide tipped tools are briefly outlined.INTRODUCTIONIn recent years the application of tungsten carbide to various mining tools in the mining industry, has developed to the stage where it is now regarded as an essential item in the production of coal and metal ores. In fact it is claimed that certain mining operations would not be possible if it were not for the benefits obtainable from the characteristic properties of tungsten carbide. The advantages of this hardmetal have, to some extent, influenced manufacturers to revise design specifiations of some machines, while againsome machines have actually been designed with tungsten carbide as their basic medium for operation.In general the applications fall into the following three categories:(a) Drilling hard rock by percussive means.(b) Drilling soft rock and coal by rotary means.(c) Coal cuttingThis paper is concerned with tungsten carbide tools associated with these three activities in Australia, the effectiveness of their application and significant points in their design and manufacture.

Jan 1, 1958

By N. Q. Huy

This paper describes the application of finite element analysis to simulate the static and quasi-static pile load tests in different drainage conditions. The possible effect of excess pore water pressure will be studied from the simulations results. The results show that the drainage condition has effect on the bearing capacity of a pile derived from the quasi-static pile load test. The excess of pore pressure reduces the pile toe resistance while it increases the pile shaft resistance. The factors which influence the effect of excess pore pressure are also discussed.

Jan 1, 2006

By Erle C. Donaldson

A study of subsurface waste disposal in the United States shows that in eight States a wide variety of industrial wastes are being injected into formations ranging in age from Precambrian to Recent. More than 30 wells ranging in depth from 300 to 12,000 feet are used for waste disposal into subsurface formations which include unconsolidated sand, sandstone, vugular limestone, and fractured gneiss.

Jan 1, 1964

By J. Kendall Hales

Jan 1, 2005

By M I. Pownceby, C M. MacRae, A Torpy

Electron probe microanalysis (EPMA) and quantitative X-ray diffraction (QXRD) techniques are capable of providing high-quality quantitative information regarding the phase mineralogy and distribution of alumina within iron ore samples. The techniques, however, use different methodologies in determining the mineralogical information (ie structural versus chemical), which introduces some limitations. In this study, EPMA was used to identify and quantify the deportment of alumina within mineral phases in iron ore samples (-1 mm crushed) sourced from different suppliers. Results were directly compared with quantitative mineralogical data derived from QXRD to provide an evaluation of the relative merits of both techniques. The four ores studied contained alumina either in the form of gibbsite, aluminosilicates (eg kaolinite), or associated with goethite.For minor phases, gibbsite and kaolinite, the abundance trends measured via QXRD were generally reflected in the EPMA data. Agreement was less satisfactory for the more abundant goethite phase (both low- and high-Al forms). The discrepancy may be the result of sampling issues arising from textural features such as grain size, and also a systematic overestimate in the amount of Al-rich goethite when hematite and Al-bearing phases are finely intermixed and the EPMA step size is coarse. A second difference in the EPMA results compared to the QXRD data was in regard to quantification of low-Al and high-Al goethite phases. The sensitivity of the chemical-based EPMA was better for distinguishing between high- and low-Al goethite although the results remain overprinted by potential errors introduced via sampling.Care should be taken when directly comparing results from each method, although in general the data should be considered complementary, as each approach provides slightly different results and interpretations regarding the overall mineralogy.CITATION:Pownceby, M I, MacRae, C M and Torpy, A, 2017. A comparison of X-ray and electron-based analysis techniques for characterising the mineralogy and alumina distribution in iron ores, in Proceedings Iron Ore 2017, pp 593–598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Onur Kacar

A numerical approach has been implemented to assess the settlements of pile groups bearing in clay. A three-dimensional finite element program has been utilized to model a vertically loaded spread footing, a single pile and a pile group. The soil-pile interaction was modeled with elastoplastic soil and interface elements. The model has been calibrated using a full scale load test results of the spread footing. The load transfer between the pile cap and the piles was assessed and compared with the measured load transfer. The predicted settlements for the pile group were compared with the settlements measured in the load test. Two analytical methods were adopted to predict the pile group settlements and they were compared with the measured values. The group effect determined from the analysis and load tests was compared with the interaction factor approach. It was shown that three-dimensional finite element approach can be successfully utilized to assess the soil-structure interaction and hence the load transfer between the piles and pile cap. Also, it was shown that the interaction factors method and equivalent footing method work well in the working stress range, however they underpredict the settlements at larger loads. INTRODUCTION The settlement and stress distribution of pile groups have been traditionally estimated based on load test results of single piles and accounting for the group effect using various approaches. The most widely used approaches are group interaction factor method, equivalent footing method and equivalent pier method. These approximate solutions are used very commonly in practice as full-scale load tests on pile groups are very expensive and time consuming. These approximate solutions are also adopted in design guidelines such as AASHTO LRFD Bridge Design Guidelines (2014) and FHWA Design and Construction of Driven Pile Foundations (2016). In this paper, a full-scale foundation load tests performed by Nagai et al. (1961) and reported by Koizumi and Ito (1967) is modelled using a three-dimensional numerical method. The settlements and the stress distribution on foundations were then compared with the traditional equivalent footing method and interaction factor methods.

Jan 1, 2018

By ROLLIN THOMAS CHAMBERLIN

The studies herein reported were begun as a part of researches undertaken by the United States Geologü;al Survey looking to the more effcient utilization of the coal in the United States through the reduction of waste in its extnidion, and were continued as part of further researches having regard to the conservation of the fuel resources of this country and to the lessening of injuries and fatalities in coal mining. Among other phases of the general problem to be studied were the origin of the gas whidi escapes into coal mines, its modes of occurrence in the coal and rock strata, and the conditions governing its outflow into the mines. The subject of relative danger from destructive explosions due to gas and coal dust in different mines belonging to different coal fields was to be one of the principal lines of investigation. But this work was barely under way when the series of unusually disastrous explosions in the Naomi, .Monongah, and Darr mines of Pennsylvania and West Virginia, in December, 1907, afforded an exceptional occasion to observe the behavior of explosions on a large scale. Because of the opportunities for study afforded by these terrific explosions, the inquiry originally planned was d ¡verted to the more specific investigation of the conditions in tl10SC mines, and the examinations have been directed toward finding those qualities of gas and dust which were concerned in these explosions. The following discussion, therefore, consists essentially of a report on that subject; but it is far from being exhaustive, and is to be regarded as a preliminary outline of investigations which are still in progress. The first of the three mine explosions mentioned occurred in the Naomi mine of the United Coal Company, near Bellevernon, Pa., on Sunday, December 1, at 7.40 p. m. All the men who were within the mine at the time, fortunately only 34, were killed. Less than a week later there occurred in mines Nos. fì and 8 of the Fairmont Coal Company at Monongah, W. Va., the most disastrous mine explosion yet recorded in the annals of American mining. The mines were comparatively new and well laid out. Mine No.8 had been in operation only about two years and was the pride of the Fairmont Coal Company. Mine No.6 was first opened ahout four years earlier. In order to make it possible, in case of emergency, for either mine to be ventilated by the ventilating system of the other, the two sets of workings were connected underground. The F face heading of mine K o. 6 led direetly into No.2 north heading of No.8 mine. On Friday, Dcccmber 6, at about 10.30 in the morning, an explosion of unusual violcnce swept completely through both mines, pursuing its course throughout the numerous ramifications and bursting out of the two pit mouths, located It miles apart, nearly simultaneously. The slope of mine No.6 was only slightly damaged, but at the mouth of No.8 the destruction was very great. The fan was wrecked, the engine house was demolished, and mine timbers were blown across Monongahela River: As nearly as can be determined, 361 men were killed in the two mines by the explosion. .While the inspection of the Monongah mines was still in progress, on Thursday morning, December 19, at about 11.20, a similar explosion wrecked the Darr mine of the Pittsburgh Coal Company ut Jacobs Creek, Pu.; 238 men lost their lives in this explosion, which in number of casualties is second only to the :Monongah disustcr in the history of American mining. Of ull thc men in the mine at the , time of the explosion, only one mun, who happened to be within 100 feet of the ~iUrface on an old manway in a wet, unexploded portion of the mine, succeeded in escaping alive. The underground investigation of these mines was made in cooperation with Clarence Hall and ""Valter O. Snelling, of the United States Geological Survey, and James ""V. Paul, now of the Survey but at that time chief of the department of mines for vVest Virginia, to all of whom the author is greatly indebted for valuable assistance, suggestions, and advice. Mr. Paul will rcport on the nature of these explosions, the precipitating causes, their destructiveness, and the general cüliditions in these mines following the disasters. The present report is confined essentially to the laboratory examination of some of the explosive materials collected from these mines directly ufter the explosions.

Jan 1, 1911