Search Documents

By Peter Klaver

Deep tunnels have been used for decades for the temporary storage of large volumes of urban runoff, both storm water and combined sewer overflow (CSO). Tunnels are attractive because they reduce surface disruption and do double duty as storage and conveyance systems, collecting overflows from multiple locations and transporting them for treatment to various facilities. Like any hydraulic system, however, there are dynamic effects that must be fully understood during the design phase so that the final constructed product does not have unintended negative consequences. Preliminary sizing of storage tunnels is typically based on the total volume required. For example, if studies have determined that a volume of 56.8 ML (15 million gal) will provide the intended level of control, then that figure can be used, along with a preliminary idea of the desired tunnel length, to compute the required diameter. Of course, filling a long tube with water from various points along the way is not at all the same as pouring water into a bucket, and these dynamic effects require additional attention from design engineers. The rapid filling of storage tunnels can lead to the formation of bores, which are essentially moving walls of water. An open channel bore can build in height until it reaches the crown of the tunnel, at which point it becomes a pipe-filling bore. Figure 1 depicts both kinds of bores moving upwards in a rapidly filling tunnel. Bores can strike the ends of tun-nels with tremendous force, driving water and entrained air upwards into dropshafts and creating strong pressure surges in portions of the tunnel that are already filled. If the hydraulic surges are high enough to reach grade, they can cause overflows and/or damage structures at the surface. Trapped air pockets can occur through several phenomena, including the reflection of bores off dropshaft structures and the occurrence of ?premature pressurization.? The latter refers to the situation where the inflow to a tunnel is increasing more rapidly than the tunnel can convey it, such that the pipe becomes surcharged at an upstream point while points downstream are still flowing as an open channel. These air pockets are a great nuisance as they migrate toward points in the tunnel where they can rise to the surface, which are often shafts that are already filled with water (Fig. 2). The ?geyersing? that results can be hazardous and costly.

Jan 3, 2010

By C. Laughton

The Deep Underground Science and Engineering Laboratory (DUSEL) is to be constructed at the defunct Homestake Mine, in South Dakota. As a cornerstone of DUSEL?s research program, it is intended to conduct experiments into the fundamental nature of neutrino and proton particles. The experimental apparatus required to con-duct these experiments will be housed in large rock cavern(s) sited at depths of over a kilometer. As conceived, these cavern(s) are planned to have mined volumes of up to half a million cubic meters, and spans of approximately 50 meters. The paper will describe key end-user requirements, and outline the in situ rock conditions and mine site constraints that are likely to play determinant roles in identifying candidate sites and developing cost-effective design options(s).

By Marko Lampi, Marc Nicolle, Janne Karonen, Kari Valkama

"In the ten years from 2003 to 2013 global mine production of copper has increased by over 23% to meet demand while the weighted average head grade has dropped from 0.9 to 0.7% Cu. These divergent trends of increasing demand and declining economic grades will extend the life of many existing mines and improve the viability of marginal and/or complex copper deposits. Against that context this paper outlines hydrometallurgical copper sulphide leaching options as alternatives to the more conventional pyrometallurgical processing route of copper sulphides. Three copper sulphide leaching and refining processes are discussed: total pressure oxidation, ferric sulphate leaching and copper chloride leaching. The effect of mineralogy on the choice of processing technology is discussed as well as some of the unit processes used. Additionally, possible benefits that a hydrometallurgical process may offer over an existing pyrometallurgical route are discussed. Subsequently, two very important aspects to the development of projects involving the leaching of copper sulphides are discussed. Finally, a number of conclusions are presented that will be useful to keep in mind when considering projects involving the leaching of copper sulphides. INTRODUCTION In the ten years from 2003 to 2013 global mine production of copper has increased by over 23% to meet demand while the weighted average head grade has dropped from 0.9 to 0.73% Cu (Murphy, 2014). If these divergent trends of increasing demand and declining economic grades continue, they will contribute to the extension in life of many existing mines and improve the viability of marginal and/or complex copper deposits. Against that context, this paper outlines hydrometallurgical copper sulphide leaching options as alternatives to the more conventional pyrometallurgical processing route for copper sulphides. Three copper sulphide leaching and refining processes are discussed: total pressure oxidation, ferric sulphate leaching and copper chloride leaching. Ferric sulphate leaching and copper chloride leaching are carried out at atmospheric pressure while total pressure oxidation takes place at elevated pressures."

Jan 1, 2015

By Robert L. Lagace

This report presents a mathematical model for the propagation of UHF radio waves in the large cross-section tunnels of a room and pillar limestone mine, and describes the analysis of a small amount of propagation data obtained in a limestone mine. The model and analysis is based on the waveguide mode theory developed earlier for the transmission of UHF waves in coal mine tunnels, with allowance for propagation losses due to refraction into the tunnel walls, to scattering by wall roughness, and to long range random tilt of the walls. Propagation around corners and through pillars is also examined based on a ray theory approach, together with the beneficial effects of placing reflectors at intersections to significantly reduce corner losses. The theory is found to be in fair agreement with the data; however, additional in-mine measurements are needed to provide a more conclusive test of the model.

Jan 1, 1979

We present a novel hybrid algorithm for quantifying the ore grade variability that has central importance in ore reserve estimation. The proposed algorithm has three stages: (1) fuzzy clustering, (2) similarity measure, and (3) grade estimation. The method first considers data clustering, and then uses the clustering information for quantifying the ore grades by means of a cumulative point semimadogram function. The method provides a measure of similarity and gives an indication of the regional heterogeneity. In addition, grade estimations can be obtained at different levels of similarity using a weighting function, which is the standard regional dependence function (SRDF). Keywords: Grade, fuzzy clustering, similarity measure, point madogram, weighting function.

Jan 1, 2008

By B. M. O'Harra

The residues resulting from the retort distillation of zinc ores have from 40 to 75 per cent of the weight of the original ore and contain from 5 to 15 per cent zinc . A rough estimate indicates that approximately 450,000 tons of residues are produced annually in the United States , containing about 36,000 tons of zinc . Besides the current production of residues there are at many smelter sites large accumulations from past operations which are available for treatment if this can be done profitably . In addition to their zinc content the residues contain much unconsumed coal , which has been carbonized during the distillation process , and those from most western ores also contain lead and silver . In this paper is summarized the information obtained in a survey , recently made by the Bureau of Mines , in cooperation with the Missouri School of Mines and Metallurgy , of processes which are in use or which have been suggested for the treatment of retort residues . The complete report of the survey is to be published as a Technical Paper of the Bureau of Mines .

Apr 1, 1923

By Edwin B. Eckel

This paper, based on brief field examination and on data supplied by the operators, records the condition of the Italian mercury industry as of March 1945, not long after Italy's collapse. Except for the once-Italian but now Yugoslavian Idria mine near Trieste, virtually all the known mercury deposits are in the Monte Amiata district in Siena and Grosseto Provinces, 75 miles north of Rome. This district contains the Abbadia San Salvatore. the Siele. the Argus, and the Cerreto Piano mines besides numerous prospects and unproductive mines. Under pressure from Germany the principal mines were highly productive during the early part of the war, but production fell off long before its end. All of the mines were damaged in some way at the German withdrawal but by September 1944 the Abbadia had resumed production and several others were only lacking power by the early spring of 1945. The Monte Amiata district is characterized geologically by a thick series of sedimentary rocks that range from Triassic to Eocene in age . and are surmounted on Monte Amiata itself by a thick cap of extrusive trachyte. Bodies of travertine and of landslide detritus, younger than the trachyte, are rather widespread. The structure is complex and little known but most of the ore deposits seem to lie along or near a major, north-trending fault or on associated cross-fractures. Cinnabar is the only important ore mineral and clay minerals are by far the most abundant products of hydrothermal alteration. A southward increase in the amount of stibnite, relative to cinnabar, suggests horizontal zoning. The grade of ore ranges from 0.60 to 3.0 Pet and the reserves, as compared with those in American mines, are enormous. Even in the face of war-time scarcities, the mines are remarkably self-sufficient and labor is plentiful, but the costs of production are estimated to be not greatly below those of the better American mines. Notes on the principal mines, on the mining and metallurgical methods, and on the manufacture of synthetic cinnabar are included in the paper. Introduction With but few brief interludes, Spain and Italy, including the Idria mine near Trieste, which has passed from Austrian to Italian to Yugoslavian hands in the Past 3 decades, have led the world in the production of mercury, or quicksilver, for many centuries. Despite their enviable position with respect to the supplies of a metal so essential in both war and peace, there is a notable lack of up-to-date information in America on the mercury industry of either country. Duschak and Schuette' and Schuettez,3 give by far the best summaries in English known to the writer, but the latest firsthand report cited by them on the Italian mines was published in 1915.' Having been deeply interested in the geology and economics of mercury for several years, the writer naturally felt most fortunate in being the to obtain enough firsthand information on the Italian industry to fill at least a few of the gaps in our knowledge. The opportunity came during the war, soon after this industry, together with the rest of Italy, had capitulated to the Allies. Many of the facts presented here are thus definitely "dated," but others are of less transitory nature, and even the dated facts should be of interest in showing the strength and

Jan 1, 1949

By Edwin B. Eckel

This paper, based on brief field examination and on data supplied by the operators, records the condition of the Italian mercury industry as of March 1945, not long after Italy's collapse. Except for the once-Italian but now Yugoslavian Idria mine near Trieste, virtually all the known mercury deposits are in the Monte Amiata district in Siena and Grosseto Provinces, 75 miles north of Rome. This district contains the Abbadia San Salvatore. the Siele. the Argus, and the Cerreto Piano mines besides numerous prospects and unproductive mines. Under pressure from Germany the principal mines were highly productive during the early part of the war, but production fell off long before its end. All of the mines were damaged in some way at the German withdrawal but by September 1944 the Abbadia had resumed production and several others were only lacking power by the early spring of 1945. The Monte Amiata district is characterized geologically by a thick series of sedimentary rocks that range from Triassic to Eocene in age . and are surmounted on Monte Amiata itself by a thick cap of extrusive trachyte. Bodies of travertine and of landslide detritus, younger than the trachyte, are rather widespread. The structure is complex and little known but most of the ore deposits seem to lie along or near a major, north-trending fault or on associated cross-fractures. Cinnabar is the only important ore mineral and clay minerals are by far the most abundant products of hydrothermal alteration. A southward increase in the amount of stibnite, relative to cinnabar, suggests horizontal zoning. The grade of ore ranges from 0.60 to 3.0 Pet and the reserves, as compared with those in American mines, are enormous. Even in the face of war-time scarcities, the mines are remarkably self-sufficient and labor is plentiful, but the costs of production are estimated to be not greatly below those of the better American mines. Notes on the principal mines, on the mining and metallurgical methods, and on the manufacture of synthetic cinnabar are included in the paper. Introduction With but few brief interludes, Spain and Italy, including the Idria mine near Trieste, which has passed from Austrian to Italian to Yugoslavian hands in the Past 3 decades, have led the world in the production of mercury, or quicksilver, for many centuries. Despite their enviable position with respect to the supplies of a metal so essential in both war and peace, there is a notable lack of up-to-date information in America on the mercury industry of either country. Duschak and Schuette' and Schuettez,3 give by far the best summaries in English known to the writer, but the latest firsthand report cited by them on the Italian mines was published in 1915.' Having been deeply interested in the geology and economics of mercury for several years, the writer naturally felt most fortunate in being the to obtain enough firsthand information on the Italian industry to fill at least a few of the gaps in our knowledge. The opportunity came during the war, soon after this industry, together with the rest of Italy, had capitulated to the Allies. Many of the facts presented here are thus definitely "dated," but others are of less transitory nature, and even the dated facts should be of interest in showing the strength and

Jan 1, 1949

By Sean Gallagher

Bolting large sheets of wire mesh screen (WMS) to the roof of underground mines prevents injuries due to rock falls. However, WMS can be heavy and awkward to lift and transport, and may result in significant spinal loading. Accordingly, six male subjects (mean age =45.8 years + 7.5 SD) were recruited to lift WMS in a laboratory investigation of the biomechanical demands. Biomechanical modeling was used to estimate external moments about L5-S1 for sixteen lifting tasks, using two sizes of WMS. Full-size WMS involved a two-person lift, while half-size WMS involved a one-person lift. Lifts were performed under 168 cm and 213 cm vertical space. Restriction in vertical space increased the maximum L5-S1 extensor moment from 254 to 274 Nm and right lateral bending moment from 195 to 251 Nm. Lifting full sheets of screen (as opposed to half sheets) resulted in an average 33 Nm increase in L5-S1 extensor moment. The L5-S1 extensor moment was increased by an average of 44 Nm (18%) when lifting screens positioned flat on the floor compared to an upright position. Relevance to industry: Large flexible materials are commonly lifted in industrial work environments, and may involve the efforts of two or more workers. The current study examines the low back loading associated with lifting large flexible screens and presents recommendations to reduce spine loading.

Jan 1, 2009

By Jon G. Bredeson

The electromagnetic noise that exists in a mining environment is quite severe and was shown to have been reasonably well documented by a number of researchers in the Phase I Report. The noise levels are such that prudent communication design requires the careful use of all the electromagnetic noise data available. A comprehensive survey was undertaken to determine techniques used in various industrial environments to achieve secure communications in the presence of electromagnetic interference. The techniques were given in the Phase I Report and are rudimentary, but have produced reasonably good results. A number of these techniques could be applied to the mining environment.

Jan 1, 1980

By R. W. Smith

Many industries such as the cement industry handle large quantities of limestone and clay slurries. However, at present very little is known about the flow properties, such as friction loss due to flow of slurries in pipelines. This lack of knowledge has made it often very difficult to calculate the total dynamic head of a proposed slurry handling system, and therefore has often made the selection of correct size slurry handling equipment difficult. Because of lack of knowledge about slurry flow a study of slurry flow theory has been made at the Portland Cement Association's Research and Development Laboratory with the idea of developing a method whereby friction losses due to slurry flow may be predicted for any size pipeline. The flow equations developed have been checked by pilot plant size equipment. DERIVATION OF FLOW EQUATIONS It has been known for some time that limestone and clay slurries handled in cement plants do not flow in the same manner as a Newtonian fluid such as water. When a Newtonian fluid flows the shear stress at any flow velocity is proportional to the rate of shear. This phenomenon can be illustrated by a line (Figure 1). The viscosity of the fluid is the slope of the curve. Thus, the flow properties of the material may be characterized by a single materials constant: viscosity. When a non-Newtonian fluid with the type of characteristics exhibited by limestone and clay slurr-ries flow, a similar curve can be constructed (Figure 2). This graph is a shear diagram of a Bingham plastic non-Newtonian fluid. It should be noted that with the Bingham(1) plastic type of flow viscosity, the slope of the curve, is still an important materials constant. In addition, however, there is another materials constant, namely the yield stress of the material. One way to visualize this constant is to consider it as the amount of energy that must be put into a Bingham plastic material to start it flowing.

Jan 1, 1961

By Donald O. Capstick

A mineral survey of a 5,700-acre portion of the 11,510-acre Upper Deep Creek Wilderness Study Area (ID-111-44B) in southwestern Idaho was conducted by the U.S. Bureau of Mines in 1985. No mining claims have been located, no minerals have been produced, and no resources have been identified in the study area. Three reconnaissance samples of alluvium from the Deep Creek drainage contained $0.21, $0.22, and $2.72 per cubic yard in placer gold, higher than usual for the Owyhee River canyonland area. The samples of near-surface material contained very fine gold in values too low to support large-volume commercial placer operations, but the quantity and size of the particles of gold in the alluvium is expected to increase near bedrock. Consequently, the area may be a target for recreational as well as small commercial suction dredge operations. The physical characteristics of the individual pieces of gold (bright and angular) indicate that it may have recently come from an unidentified nearby source.

Jan 1, 1986

By D. Bienstock

To develop a rugged catalyst capable of withstanding hydraulic attrition resulting from the oil-circulation process for synthesizing liquid fuels, use of an iron catalyst containing an active coating surrounding an inert solid core of metal was investigated. This massive-iron catalyst in the form of steel shot and lathe turnings was activated by partial oxidation with steam at 600° C, impregnated with alkali, and reduced with hydrogen at 450° 6. The massive-iron catalysts were resistant to oxidation and spalling, and a 6-month catalyst life was attained. Higher operating temperatures could be employed than with fused iron oxide catalysts, resulting in greater gasoline yields. Because the lathe turnings pack with void volumes of 70 to 90 percent, it has become possible to employ a fixed bed without the danger of cementation that occurs with fused iron oxides.

Jan 1, 1963

By A D. Campbell, G R. Power

Many caving mines use numerical flow models to simulate mine production, forecast recovered ore grades and optimise the draw strategy. In sublevel caving (SLC) mines, the effects of blasting and fragmentation at an individual ring scale generally cannot be included in these models. Previous attempts to use results from marker recovery trials to calibrate numerical flow models have been limited due to difficulties in accounting for blasting effects at a ring scale. This paper outlines how an empirical criterion for blasting and fragmentation was used to attribute variable flow properties into a numerical flow model based on the blast design and modelled fragmentation. The flow model was then validated using data from a number of full scale marker recovery experiments. The result of this approach was a significant improvement in forecast accuracy when compared against the same modelled cave marker recovery without the inclusion of these blasting effects. Improvements in the flow model are currently being adopted within the mine scale model to further improve the accuracy of grade forecasting, optimise the draw strategy and increase net present value. The integrated modelling approach is also being used to simulate the effects of different drill and blast designs on cave recovery. It is suggested that, if implemented, the technique would lead to improved blast designs in other SLC mines, increase the value of marker trial data and reduce costs associated with large scale blast design trials.CITATION:Campbell, A D and Power, G R, 2017. Improving calibration of flow models against SLC marker trials by linking blasting effects to particle mobility, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 11–22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Terry R. Neumann

A mineral survey of the 23,760-acre Abert Rim Wilderness Study Area (OR-1-101) was conducted by the U.S. Bureau of Mines in 1986 at the request of the Bureau of land Management in order to evaluate its identified mineral resources. The study area is located in south-central Oregon, 26 mi north-northeast of Lakeview, OR. Federal and Lake County mining records indicate no mining claims, geothermal leases, or oil and gas leases within the study area as of January 1, 1987. No economic concentrations of minerals were found in the study area. The Wilderness Study Area is dominated by Abert Rim, a north-trending Basin and Range fault scarp that parallels the study area's western boundary. Exposed on the scarp is an approximately 2,000-ft-thick volcanic sequence consisting of Oligocene-Miocene basalts, tuffs, and tuffaceous sedimentary rocks.

Jan 1, 1987

By S. J. Stokowski

Abstract An extensive drilling and laboratory testing program indicates that a construction aggregate resource is present within the Oligocene Sombrerito Formation limestone, southwestern Dominican Republic. The first part of the testing program included the collection, photographing and geologic logging of diamond drill cores to allow lithologic subdivision of the strata into potential quarry layers. The primary lithostratigraphic units are: I- (youngest) approximately 10 m of white, dense marine limestone II-approximately 5 m of white, interbedded dense and chalky marine limestone III-more than 2 m of tan, chalky, calcitic dolomite. Unit I is often altered by lateritic weathering and/or dolomitization. Unit II is often altered by dolomitization. The cores were individually crushed by quarry layer into coarse and fine aggregate sizes for chemical and physical analyses: specific gravity and absorption, MgSO4 soundness, sand equivalent, Atterberg limits of the minus #40 mesh fraction, and LA degradation. The unaltered portion of Unit I is suitable for all construction aggregate uses. Unit II is best suited for crushed stone base. Each of the non-weathered units decreases in coarse-aggregate yield and quality with depth and diagenetic dolomitization. Dolomitization typically causes about 5% lower yield of coarse aggregate, a sand equivalent of about 20 units below the original value an increase in absorption of about 3%, an increase in the LA of up to 13%, and a decrease in the average five-cycle MgSO4 soundness of about 17%.

Jan 1, 1991

The West Coast region of the South Island is situated astride the Pacific û Australian plate boundary zone. The most significant component of this zone is the Alpine Fault. A variety of reconstructions of the pre-Alpine Fault plate tectonic configuration of the New Zealand continental area have been attempted over the past 25 years or so. Most of these have not been closely constrained by a regional compilation of field data related to the age and horizontal displacement history of the Alpine Fault. A model in which the Alpine Fault was initiated no earlier than the interval 18 - 16.5 Ma (B.P.) is proposed, a significantly younger age of inception than has been widely accepted as the onset of dextral displacement along the plate boundary through the South Island. A subsequent history of displacement is presented consistent with the West Coast basin stratigraphy. The alluvial gold content of some parts of the Miocene to Pleistocene conglomerate sequences is also discussed.

Jan 1, 1996

By K. Norrena

Grade control in open pit mining requires the specification of dig limits that account for mineral grades, economic costs, and selectivity of mining equipment. Visual identification of ore rock types is ideal, but this is not always possible in lower grade disseminated deposits where ore/waste contacts are not visually discernible. In this case, conventional grade control practice consists of a two-step procedure (1) create a map of mineral grades at some selective mining unit scale, and (2) determine practical ore-waste boundaries or dig limits on the basis of the gridded block grades or assay information. This procedure is laborious, depends on a subjective assessment of where the boundary should be, and may be economically sub-optimal. We pose the determination of dig limits as an optimization problem and solve that problem with the technique of simulated annealing. Simulated annealing has the unique advantage of being able to combine multiple non-linear constraints into a single objective function. We use maximum profitability and the ability of the equipment to mine the proposed dig limits as constraints in the determination of optimal dig limits. We require a map of expected profit for eah block. Geostatistical techniques are recommended, for mapping expected profit but not necessary. Geostatistics will provide a quantification of the uncertainty in the grades within rock types using all available blasthole samples and exploration drilling. Some variant of L-optimal estimation or kriging can be used to determine the block-by-block classification that is economically optimum. We also need the expected profit for each block. It is unrealistic to assume free selection, that is, each block cannot be extracted independently of its neighbors. The optimal balance of ''accepting dilution'' and ''wasting ore'' is achieved to maximize profit subject to equipment constraints.

Jan 1, 2001

By Michael Gilbert

In the world of tunneling the glamour is in the large diameter, long tunnels, but perhaps the number of projects for small diameter and short length tunnels are greater and generally have higher risk factors. Reasons for these higher risks include both the ?boiler plate? contract provisions used on these types of contracts, the technical specifications related to the tunnel work (versus the pipeline construction), the bid practices including measurement and payment and the construction. This paper reviews and comments on some of the key issues the authors have observed in recent major pipe-line projects that involve a small percentage of tunneling footage of the total contract.

By Margarete Kalin

"Difficulties arise in implementing environmental technologies in the mining sector because important fundamental processes, which lead to the environmental degradation, are ignored. Weathering rates, the role of bacteria in the process and the incomplete application of the matching principle of accounting at the time the mining disturbance take place. Mining is a multi-stakeholder activity and the environmental problems have multivariate dimensions also effecting process.The limiting factors in the contaminant generation process are the transport of oxygen by advection, convection or diffusion in air or water and the associated microbial activity. Weathering products are transported from the mineral surface by atmospheric precipitation to surface and groundwater. This contamination takes place at different rates, requiring a long time to evaluate technological choices.Restoration efforts have to focus on slow reaction rates in the contaminant generating processes. Technology, which does not address the reaction rates and is selected based on inappropriate time scales, will not provide long-term solutions. Natural approaches to reduce acid generation, based on Ecological Engineering principles have required decades of research and field testing, but now show promise in addressing the cause of AMD and ameliorating its effects."

Jan 1, 2005