Search Documents

By Michael D. Justason

This paper details the static and Statnamic load testing on a 600 mm square pre-stressed concrete pile. The pile was located at Pier 15 on the 20 million-dollar Bayou Chico Bridge Project in Pensacola, Florida. The pile was 10.5 meters long and had a design load of 1.3 MN. Three static load test cycles were performed in November, 1996. The Statnamic load test was performed in January, 1997. The Davisson Failure load of the first cycle of the static test was 3.7 MN, and the Davisson Failure load of the Statnamic test was 3.2 MN. The load-displacement curves for the two types of tests were very similar, indicating that the Statnamic load test performed well in the sandy soils. Strain gauges embedded in the pile showed 35% skin friction and 65% end bearing for both test methods. Strain gauges were located at equal spacing at five elevations in the pile. A toe accelerometer verified the rigid body assumption of the Unloading Point Method currently used in the analysis of Statnamic load tests. The data collected from the pile instrumentation was of excellent quality and represents some of the best research to date comparing static and Statnamic load tests.

Jan 1, 1997

By G. B. Harris, A. R. Laplante

Fine tungsten was used to mimic gold and fine and coarse silica and magnetite to mimic gangue. The optimum flow rate of fluidisation water varied from 1.7 l/min for fine silica to 5.6 l/min for coarse magnetite. Overloading at optimum flow rate was then investigated. With fine silica gangue no overload occurred under any of the conditions studied, and there was very little overload with fine magnetite. Coarse silica caused appreciable overload, but only after a significant bed of tungsten had been formed; with fine magnetite gangue the onset of overloading occurred earlier. Finally, with coarse magnetite severe overloading occurred almost immediately. Overloading was modelled using a first-order kinetic rate constant for erosion of the concentrate bed and a critical mass of constant above which it takes place. The results clearly demonstrate the importance of removing oversize to maximise recovery, particularly with a high-density gangue

Jun 18, 1905

By Patrick F. R. Murphy

An ultra-low profile LHD has been developed by EJC Mining Equipment of Burlington, Ontario for narrow-reef mining applications. This paper discusses the challenges encountered during the evolution of the machine's design and subsequent field testing. Continuing research and development focuses on optimizing machine performance and controllability, reducing emissions, and enhancing maintainability. Details will be given on field trial experience and ongoing test work being carried out at the manufacturing facility.

May 1, 2004

By Fumihiko Sumiya, Shinya Tanaka, Yukio Kato, Kenji Tanaka, Tetsuya Sawada

When explosives are heated under an acidic environment due to metal sulfide and sulfuric acidity, their decomposition temperature falls remarkably and decomposition reaction occurs quickly, and then explosives have the risk of the deflagration to the detonation transition. Heat resistant commercial explosives which can be used under conditions of high temperature of 200ºC and an acidic environment were studied. We developed the explosive composition consisted of ammonium perchlorate (AP) as oxidizer, saturated hydrocarbon oil as fuel and binder, and calcium carbonate as decomposition inhibitor. The characteristics of this explosive composition show a heat resistance over 24 hours at 200ºC, and a detonation velocity over 2,500 m s-1. This explosive composition has a cap-sensitivity at temperature higher than 100ºC. Cost effective heat resistant commercial explosives were created by the optimization of the grain size of AP as a main component, the addition of saturated hydrocarbon oil and calcium carbonate, and the control of bulk density by the addition of micro-balloons.

Jan 1, 2003

By S. O. Bada

Fine phosphate feed is considered to be slime and normally disposed of as a discard in settling ponds or dumped as landfill. The purpose of this research was to establish whether commercially acceptable qualities and yields could be obtained from this material using dry separation methods. The results obtained from the electrostatic separation of <105 µm phosphate ore are presented. An existing separator was upgraded in order to improve on product and flotation concentrate recovery, to test different mineral, and to reduce particle residence time between the charging chamber and the separating zone of the separator. The operating conditions were varied according to the charges imparted to the particles in the electric field, and according to other device parameters. Parameters such as splitter position, charge reversal, rotation speed, charging voltage and separating voltage. The <105 µm phosphate feed was concentrated under both triboelectrification and inductive charging. The use of inductive charging and charge reversal resulted in a significant increase in grade for <105 µm phosphate feed, with the P2O5 grade increasing from about 12 per cent to 20.50 per cent, and a recovery of 26.30 per cent under a single stage of separation. It was found that better separation was achieved at rotation speed of 6000 r/min, -8 kV charging voltage, and 25 kV separating voltage.

Jan 1, 2012

By Hiroshi Soda, Atsumi Ohno, Hiroyuki Yamazaki, Alexander McLean

INTRODUCTION The method of heat removal during a casting process strongly influences the crystal morphology of the cast product and hence the metallurgical and mechanical properties of the solidified materials. In this paper, the Ohno Continuous Casting Process (OCC) is described in terms of the casting conditions and the type of structure observed in the cast product. Significant improvements are observed in workability, fatigue strength and corrosion resistance of castings produced by the OCC method, Ohno (1988). Applications of this technique to low melting point nonferrous metals and alloys are discussed. The feasibility of the application of this technology to high melting point materials is outlined. THE OCC PROCESS The OCC process involves delivering liquid metal into a heated mold, the temperature of which is held just above the solidification temperature of the metal to be cast. This is the key point which differentiates the OCC process from the conventional continuous casting method. A schematic illustration of the OCC process is shown in Figure 1. The Formation of a Single Crystal When the mold is heated above the solidification temperature of the metal to be cast, nucleation on the mold surface is prevented and solidification takes place only at the mold exit. The heat is extracted through the product being cast by a cooling device located near the mold outlet. Crystals are formed only at the tip of the dummy bar at the start of casting, and as the dummy bar travels away with a progressively increasing speed from the mold, the position of the solid liquid interface will align with the mold exit, producing a unidirectionally

Jan 1, 1990

By A. Feldman

Measuring dynamic effects on existing structures such as dams and bridges during earthquakes or blasting is frequently done using strong motion detectors. However, a more comprehensive dynamic structural evaluation requires direct measurement of deflection, strain, and pressure changes during dynamic events. Many existing structures have vibrating wire gages already installed that can be used with modifications to the data acquisition systems to provide direct measurement of dynamic displacement, strain, and pressure. The project described in this paper provided the opportunity to demonstrate the feasibility of using vibrating wire technology to measure dynamic effects on existing structures.

Jan 1, 2006

By M. M. Tilman

Etchants containing hexavalent chromium and sulfuric acid are used in a variety of surface-finishing operations. When the resultant spent solutions are discarded, substantial quantities of chromium are lost and pollution prob¬lems are created. To minimize the undesirable environmental effects while improving metal and minerals recycling technology, the Bureau of Mines is con¬ducting research on a method for the economic inplant recycling of these waste etchants. Trivalent chromium, produced when the etchant reacts with a substrate, is oxidized in the anode chamber of a diaphragm cell; other metals, dissolved during the etching operation, are transferred to the catholyte. When waste brass etchants are treated in this manner, all of the trivalent chromium is oxidized and more than 40 percent of the copper and zinc is removed. Similar copper removal and chromium oxidation are achieved with waste printed circuit board etchants and rinse waters from plastic etching operations. The electrical energy needed to regenerate 1 kg sodium dichromate is less than 9 kwhr. Regenerated brass etchants evaluated by two companies equaled or exceeded the performance of fresh etchants.

Jan 1, 1979

By Manuel Sanchéz

Para las empresas mineras, la búsqueda de buenas condiciones con los clientes y la optimización de los procesos involucrados en la cadena de valor, es uno de sus principales objetivos. En este sentido, el presente texto señala las estrategias y soluciones que priorizen y mejore la calidad de las decisiones en la empresa.

May 25, 1998

By Bruno Lemelin

Falconbridge Ltd Raglan Mine has been in production since 1998 and has produced annually some 900 000T of ore grading 3.1% nickel, 0.9% copper and 0.06% cobalt. The mine is located in Nunavik, Northern Quebec. The current mine life is estimated at approximately 20 years. Reserves are composed of numerous small ore bodies situated across a 65 km strike length. Planning the extraction of the ten small mineralized zones represents a great challenge to optimize. The overall objective is to maximize the company?s return on net assets. Actual planning uses computerized technology tools like Automod and Mine2-4D, and a conventional discounted cash flow method (DCF) of calculating net present value (NPV). The complex setting of Raglan could benefit from advance valuation techniques such as the real options method (RO). This paper will present the characteristics if the mines that make it a good candidate to use RO to gain further insight.

May 1, 2004

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

This paper is concerned with the blasting of rock in mining. The most common purpose of blasting rock is to cast it or to disrupt its structure sufficiently for effective digging and subsequent removal.

Jan 1, 1991

By Wu Xueling

9K medium was used to isolate iron-oxidizing bacteria from 27 sump water samples collected from Dexing Cop-per Mine, Chengmen Mountain Mine and Yin Mountain Mine, Jiangxi Province, China. Lead acetate and silver nitrate were used to enrich metal-resistant iron-oxidizing bacteria from the above water samples. Isolate 16 was isolated from the sample taken at Dexing Copper Mine. Growth experiments indicated that when incubated under lead acetate (3,500 mg/L), isolate 16 still carried out ferrous ion oxidation, while isolate H1, a less resistant strain taken at Yin Mountain Mine, had a tolerance level of only 400 mg/L. When assayed with other metals, i.e., Ag+ (240 mg/L), Hg2+ (0.9 mg/L), Cu2+ (32,000 mg/L) and Mg2+ (22,500 mg/L), isolate 16 still carried out ferrous ion oxidation while, on the other hand, isolate H1 exhibited much lower tolerance levels, i.e., Ag+ (60 mg/L), Hg2+ (0.1 mg/L), Cu2+ (19,000 mg/L) and Mg2+ (13,500 mg/L). Based on 16S rDNA sequence data, isolate 16 and H1 were both identified as Acidithiobacillus ferrooxidans.

Jan 1, 2007

By B. Moore, Y. J. Zhang

In today’s competitive dimensional stone business environment, use of available technology is critical to achieve and maintain a competitive advantage. Awareness of improvements in diamond cutting technology, operation planning/scheduling, and geotechnical data manipulation/implementation are the keys to success. This paper presents the modern techniques of limestone sawing and quarrying developed and adopted by Indiana Limestone Company, Inc.(ILCI).To fulfill the growing market demands, ILCI’s quarries are committed to deliver planned quantities of all type of stone blocks in a variety of different colors, sizes, and textures. This involves scheduling which quarry ledges should be mined and when in order to minimize unnecessary inventory buildup. Challenges associated with ILCI’s operation are discussed and summarized in the closing of this paper.

Jan 1, 2004

By Victor E. Kral

The Valery fluorspar deposit , also known as the Hamilton deposit , is northeast of Lovelock and 4 miles by poor dirt road east of U. S. Highway 40 . It is in the Humboldt Mining District , on the west side of the Humboldt Range , at an altitude of 6,000 to 6,500 feet . The property was examined by the Bureau of Mines on February 83/ and April 8 , 1944.4/ The last examination was made with an engineer of the Geological Survey.5/ Exploring by means of trenches , cuts , shaft sinking , coyote holes off the shaft , and a small amount of prospecting with short drill holes , was begun in January 1945 and was completed June 30 , 1945. An engineer6/ of the Geological Survey visited the property in April and again in June 1945 to complete a topographic map of the area and to note the results of exploration by the Bureau of Mines . Only minor surface exploring had been done on fluorspar occurrences previous to the Bureau's work . No mining equipment or living facilities are on the property .

Feb 1, 1947

It is crucial to reestablish a domestic rare earths minerals production industry to help secure the Nation&apos;s clean energy future, reduce the U.S. vulnerability to material shortages related to national defense, and to maintain our global technical and economic competitiveness. Given that the Chinese dominance of the rare earths market has adversely impacted supply stability and endangers the United States and its allies&apos; assured access to key materials, rare earths should qualify as materials either strategic or critical to national security. Further, the U.S. government should facilitate the reintroduction of a globally competitive rare earth industry in the U.S. Realization of this objective requires: ? Developing domestic processing capability so that the U.S. is not primarily dependent on China as a source of rare earth ore, and almost exclusively dependent of China for processing of the ores. ? Providing a mechanism where access to Federal lands for rare earth exploration and extraction is possible, and ? Training engineers to design and operate rare earth ore processing facilities

Jan 1, 2011

By A T. Job, P R. McAree

There is significant value at stake in the mining industry from the implementation of new technologies that support the enhanced profitability and sustainability of mines. However, in order to realise this value, new technology must be implemented in a way that is both effective and sustainable. The industry has a mixed history for technology implementation that provides fertile ground for understanding what is necessary for innovation to deliver value. This paper describes early stage research investigating why this is so, with the aim of improving how to deliver value. Several case studies are provided covering both successful and unsuccessful technology interventions. The paper identifies the common factors that emerge from the case studies, and offers a path forward for further research in this area.CITATION:Job, A T and McAree, P R, 2017. Three case studies on the implementation of new technology in the mining industry, in Proceedings Iron Ore 2017, pp 407–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The technical parametrization of reserves is a technique which has made an important contribution to the definition and the calculation of optimal mining projects. Its applications to a new open-pit optimization program have already been presented in various papers (François-Bongarçon and Maréchal (1976); François-Bongarçon and Guibal (1981)). The present paper gives a brief description of the general problem of parametrizing reserves before going into the details of the practical algorithms used in two typical cases, i.e. open-pit mining and mining between hanging wall and foot wall.

Jan 1, 1982

By Andy Cole

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual-alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

May 1, 2002

By R. S. Warfield

Several reconnaissance-type surface and drill core samples of Arctic Northwestern Alaska coals were taken during the summer field seasons of 1964 and 1966 for coking studies. Surface samples were taken from the Kokolik River and the Cape Beaufort areas; core samples were obtained from the Kukpowruk River and the Cape Beaufort areas. Only one Kokolik River surface sample possessed coking properties. This sample, representing an 11.6-ft coal seam, made coke approaching metallurgical quality when a 30-pct portion of selected blending coals was added. Four Kukpowruk River core samples, each representing the same 19-to 20-ft coal seam, were all of about the same coking quality. No differences of coke quality attributable to depth of permanently frozen overburden were found, but the data confirm previously reported information that the 19- to 20-ft coal bed is a potentially satisfactory base coking coal. In the Cape Beaufort area, a core sample with appreciable coking properties was taken at depth from a coalbed determined noncoking in a surface sample.

Jan 1, 1969