Search Documents

Inhibition of Bubble Coalescence by Salts and Sugars

Sep 13, 2010

Pressing-Drill Method - A Representative Method for Taking Analysis Samples from Recycled Materials

Sep 13, 2010

By R. J. Snoby, M. A. Short, A. Jungmann

In processing coal, the low concentrate value requires high capacity production and sharp classification/separation techniques to reduce specific production costs. The allflux separator meets these criteria with a unique two-stage design. Through a combination of rising current and fluidized bed technologies, the allflux has extended the state of the art by expanding the particle size range that can be efficiently processed. Using concepts that have proven successful in processing concrete sands, small-scale industrial testing with coal feed stocks looks very promising. Attractive applications for the allflux are projected in fine coal recovery from old settling ponds or as a retrofit in existing fines circuits.

Jan 1, 2001

By J. E. Chilton

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to determine the influence of mining machine-mounted scrubbers on airflows and methane concentrations at the face when blowing ventilation systems are used. Tests were conducted in a full-scale ventilation gallery with a model mining machine that simulated airflow created by a dust scrubber. During the tests, ultrasonic anemometers were used to measure airflow speed and direction at several locations near the face. For the same test conditions, methane was released from the face and gas concentrations were measured at 21 locations above the machine using fixed point methanometers. Changes in airflow speed and direction are correlated with scrubber airflow and the measured methane distribution above the mining machine. The research results showed that operation of machine-mounted scrubbers improved face ventilation when blowing ventilation is used by increasing both the intake flow and the quantity of air reaching the face.

By M. Buxton

Sensor derived data can add value across the mining operating chain ranging from resource definition, extraction, pre ? concentration, mineral process monitoring and assessment of product quality. Most documented studies on the use of sensors in mining focus on specific technologies for specific applications. These studies do not take into account different aims, objectives and operating conditions at different steps in the value chain. The first part of this contribution assesses key physical performance and discriminatory requirements of sensors applied in each portion of the mining value chain. The second part proposes a framework of methods for quantifying the value added by additional sensor information. Integrating the sensor based technology and the economic value quantification allows for both, designing an economically optimal sensor monitoring network along the whole mining value chain and optimizing efficiencies. Illustrative studies demonstrate the significant economic benefits, in particular in reduction of exploration expenditures, increase in extraction efficiencies, increase in ore product quality and improvement of processing efficiencies.

Feb 27, 2013

By John K. Alley

Despite the extensive use of fluorphlogopite, investigators do not agree as to its exact melting temperature. Data on other fluormicas and on related fluorsilicate systems are largely nonexistent. A knowledge of the melting temperature is necessary for the effective synthesis and use of fluorphlogo¬pite or other fluormicas. The increasing use of two- and three-mica systems to yield polycrystalline ceramics has made more urgent the need for melting temperature information concerning these other fluormicas. This report is part of a program by the Bureau of Mines to synthesize large-size or large-crystal fluorphlogopite and develop a usable reconstituted fluormica sheet. The melting temperature of fluorphlogopite, K2Mg6A12Si6020F4, was found to be 1,383° ±2° C. This temperature was found by studying single crystals of fluorphlogopite, heating behavior of glass of fluorphlogopite composition, and the actual crystallization of fluorphlogopite from a melt that had been heated above 1,430° C. The formation of forsterite or norbergite was directly proportional to the loss of volatiles during the experimentation. Many trials revealed that the only reliable seal was a thick platinum sheet with welded seams. If no volatiles were lost, neither norbergite nor forsterite were formed; fluormica was then the only product. Excellently formed crystals of forsterite with an optical sign different from ordinary forsterite were obtained during the single crystal melting experiments. These crystals resulted from a slow loss of volatiles. A congruent melting of fluorphlogopite is indicated by the data of this report; however, incongruency within a small temperature range is not precluded. A more refined method using phase equilibria-quench methods would be necessary to settle the question absolutely.

Jan 1, 1962

By François Girard

La zone 1 de la mine Doyon (zone altérée), se situe à l?extrémité sud de la mine et est constituée d?une série de veines étroites à fort pendage et ayant des épontes de très faible résistance. Les épontes supérieure et inférieure ont des valeurs de RQD variant de 0 à 20 lors que les valeurs de RQD de la zone minéralisée se situent entre 20 et 40. Le minerai de la zone 1 s?étend sur environ 300 m de long et sur 900 m de profondeur avec des épaisseurs variant entre 2 et 15 m. Des méthodes de minage long-trous y sont utilisées avec des accès longitudinaux ou transverses selon l?épaisseur de la zone minéralisée. L?exploitation de la zone 1 a débuté en 1991 et plus de 1,7 millions de tonnes auront été extraites à la fin 2008. Plusieurs techniques y ont été testées que ce soit au niveau du développement ou du minage afin d?améliorer la sécurité des travailleurs, de réduire la dilution des chantiers et d?en augmenter la récupération. Différentes modifications ont été apportées aux dimensions et orientations des galeries, aux patrons de forage, aux techniques de sautages, au support de terrain, à la séquence de minage et aux méthodes de remblayage. Le texte suivant élabore sur plusieurs approches utilisées lors du minage de la zone 1.

Feb 1, 2008

By Pat Wilmoth, Joseph P. Gildner, Dan Nowak, Shane Yanagisawa, Don Z. Painter, Gordon F. Revey

Frontier/Traylor is presently completing construction of twin tunnels for the Tri-County Metropolitan Transit District of Oregon’s (Tri-Met) westside lightrail system. The tunnels are each 4,550 m (14,935 ft) in length and 6.48 m (21.29 ft) in diameter. The 1/3 of each tunnel was driven from the west portal using drill and blast methods and the remaining 2/3 was driven from the east portal using a TBM. The paper describes: The difficulties encountered by the TBM mining the weathered Columbia River Basalts. The execution of drill and blast work despite challenging ground conditions, stringent noise and vibrations specifications, and public relations problems. The excavation and lining of the Washington Park Station 79 m (260 ft) below the park zoo.

Jan 1, 1997

By C. B. Manula

This report is volume 5 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Subsidence subsystem of the Master Design Simulator. This subsystem uses the finite element method to simulate ground movement caused by an advancing mining face in an underground coal mine. The model is structured around the concept that the ground mass is a layered media of different thicknesses and material properties. Gob areas are considered to be unfilled with broken rock at the beginning of mining. After mining starts, the gob areas are filled with broken material which provides resistance to the lowering of the overlying strata. The model is tied to the Geology and Reserves subsystem, but it can also operate as a free standing routine. A case study is presented illustrating the application of the model. A detailed user's manual, including a program listing, is included in the appendices.

Jan 1, 1974

By M. Pérez-Tello

A mathematical model to represent the expansion and fragmentation of copper matte particles oxidized under flash converting conditions is presented. The model assumes that the particles are initially nonporous, have a constant mass prior to fragmentation and travel at a constant velocity throughout the reaction chamber. The model requires the specification of the following five parameters: the particle expansion rate, a fragmentation diameter factor, a fragmentation size distribution parameter and the fractions of the finest and the coarsest particles in the feed that undergo fragmentation. The model predictions show good agreement with the experimental data collected in a laboratory furnace over a wide range of experimental conditions. The evolution of the size distribution of the particles along the reactor length was computed, and the model parameters were correlated with the experimental operating variables. Model predictions indicate that particle residence time is an important factor in the generation of dust. The presence of two maxima in the particle density function may be attributed to turbulent conditions prevailing in the furnace, which cause particles to follow different trajectories within the furnace even if they are injected at the same location.

Jan 1, 2008

Flotation Research on Cassiterite of Tailings

Sep 13, 2010

By Douglas D. Donald

The New Jersey Zinc Co. successfully holed through a 2 1/2-mile haulage tunnel connecting its new Ivanhoe shaft with the Van Mater Shaft at Austinville, Va. This 8x 10-ft cross-section tunnel was driven from both ends and met at a point approximately a mile from one shaft and a mile and a half from the other. In order to make certain that the faces met accurately on line and grade it was necessary to refine conventional mine surveying practices. The mines that are serviced by these shafts are located in the southwestern part of Virginia approximately midway between Roanoke and Bristol at the west foot of the Blue Ridge. While the presence of lead-zinc sulfide ores has been known in this area for more than 200 years, it was in 1902 that New Jersey Zinc Co. acquired the Austinville property, which has been in constant operation since that time. About ten years ago the company undertook an extensive diamond drilling program at Ivanhoe several miles to the southwest. This program was successful in locating sufficient ore to justify the purchase of a number of the properties in this area and plans were made to develop the new orebodies. The discovery of this ore as well as substantial addi- tional reserves at Austinville resulted in a decision by the company to increase its daily milling capacity to 3000 tons, of which about 1000 tons would be supplied from the Ivanhoe mine. After careful consideration of all possible methods of transporting this volume of ore from Ivanhoe to the mill, it became evident that diesel locomotive haulage through a 2½-mile tunnel between the two mines would best suit prevailing conditions. Since the lowest operating level, known as the 1100 level, of each mine would be at approximately the same elevation, it was obvious that such a tunnel should be driven on this level. Not only would this tunnel facilitate feeding Ivanhoe ore into the underground crusher and skip loading installation at Austinville, but it would also open up a known orebody 5000 ft southwest of the Van Mater shaft. In addition it would provide a valuable diamond drilling base from which a large and a potentially favorable but untested block of ground might be explored. In order to hasten the completion of the tunnel, it was felt that it should be driven from both ends. ENGINEERING CONTROL PROCEDURES It was vital that the tunnel junction be made accurately on line and grade; thus it was felt that engineering control of an unusually high degree of reliability was required to prevent an accumulation

Jan 1, 1959

By D. B. Rebuli

Seismic networks in deep gold mines of South Africa are often planar owing to the tabular geometry of the orebody and, therefore, the mining infrastructure. Consequently, seismic event locations are poorly constrained in the direction perpendicular to the reef plane, and symmetrical locations above and below the reef plane may fit the observed data equally well. This problem may be resolved in situations where the strata above and below the reef plane have significantly different seismic velocities, which is the case for the Ventersdorp Contact Reef at Kusasalethu mine (previously Elandskraal, the amalgamation of Deelkraal and Elandsrand). A location method using a layered location model that takes into account the velocity contrast between the layers was tested. Observed direct- and head-waves were used to determine the velocity bounds of the P-wave velocities in the two-layer model. The data-set was also used to find the best P- and S-wave velocities for the two layers by grid searching over a range of velocities and minimizing the sum of the travel-time residuals. The results from the grid search and those from the calibration of velocities using direct- and head-waves give similar P-wave velocities for each of the two layers. A second set of seismic events was then relocated with this layered model and locations closer to reef were found. This simple layered location method goes some way to reduce the reefperpendicular location errors for Kusasalethu mine in particular. Keywords mine seismology, velocity model, location methods.

Jun 1, 2013

By D. G. Krige

For the purpose of determining confidence limits for ore grade estimates, an extensive simulated data base was used, which included 1728 ore blocks with ‘actual’ grades and the corresponding estimates based on ordinary and simple kriging. The practical results show that conditional unbiasedness is essential and that acceptable confidence limits can then be set using Normal theory for the simulated error distribution based on the logarithms of the ratios of ‘actuals’/estimates with a variance related to the kriging variance. The mean of the data used to prepare the variogram and the estimated block grade are to be used properly in this approach. A practical analysis was also done of the actual point and block data from a very large mined out Carbon Leader area. The distributions of the actual grades for two levels of block sizes with different levels of variability were fitted using three models, ie. 2-. 3- and compound-lognormal. The trends of tonnages, grades and relative profits for a range of pay limits, as well as the usual tonnage-grade curves, show a practical insensitivity for the choice between the three lognormal models considered.

Jan 1, 2003

By Y. He

Early research showed that the separation of particles based upon their density was not possible in steadily rising air streams. The terminal velocities of moving spheres are determined by their aerodynamic characteristics. This prevents particle separation by density in standard air classifiers. Passive pulsing air classifiers have accelerated airflow in certain regions, which achieves density-dominant separation. Numerical simulation of airflow within passive pulsing air classifiers was done to estimate airflow patterns near a damper. Analysis of those results shows the significant acceleration of the airflow above the damper. Laboratory trial separations have shown that passive pulsing classifiers are superior to standard air classifiers. Keywords: pulsing airflow, passive, simulation of airflow models, acceleration effect, density

Jan 1, 2005

By M. ROWE, H. E. Gilliland, L. BARNES

The authors of this paper are to be commended for a clear exposition of a timely subject. However, some important conclusions, in addition to those presented in the paper, can be drawn from the results of their elaborate and rather complete numerical computations. First of all, the major part of the calculations presented in the paper are for semi-infinite slabs of oil shale (the authors designate this as Model I) and a question must be posed — Are these elaborate computations needed to arrive at realistic estimates of the shale oil displaced. Consider the model of Lauwerier* that corresponds to the authors Model I if thermal conduction parallel to the fracture be neglected. If one also neglects the finite (but relatively small) heat capacity of the material in the fracture, it is easily shown from Lauwerier's solution that the cumulative oil production would be:

Jan 1, 1969

By G. D. Andria

Contract J0275007 was to consist of a thorough two-phase statistical analysis of respirable coal mine dust data from USBM Contracts H0232061, H0232060, H0230029, H0230031, H0210050, and H0242013. Consequently, BCR cataloged and assembled relevant data items from these contracts and formulated procedures suitable for the evaluation. The selected procedure was a Multilinear Regression Analysis which related dust concentrations measured in the mine to other mine parameters. Under the first phase, a thorough analysis of the date from USBM Contract No. H0230029 was completed. Primary results from this analysis are as follows: (1) The five variables that significantly affect dust concentrations in the return behind the brattice are the spray system utilized; the distance from the face to the return brattice; the return airflow; the production rate; and the water consumption rate, in that order. These five variables describe about 85 percent of the total variation in the return dust concentration. (2) Results at the miner and jack-setter locations were somewhat less conclusive due to the fact that only 17 percent of the variation in dust at the miner could be resolved and only 48 percent of the variation at the jack-setter location could be explained. The decision of the sponsor was that these initial results revealed as much information as could be expected; thus, per instructions from the USBM, the second phase (analysis of the other five contracts) was abandoned.

Jan 1, 1978

By Johann Botha, Niel de Clerk, Tony B. Lange

"PROCESS COMPLEXITYDespite many years of research and development, mineral and metallurgical processes are in general highly complex and still difficult to understand and control. One of the biggest factors contributing to this complexity is the highly non-linear, multivariate, chaotic nature of such processes.This complexity is magnified in production environments where business optimisation rather than beneficiation is the primary objective. Return on investment, sustainability, and social issues such as Aids and the environment all form part of the goal hierarchy of industrial concerns. In addition, international competition and price volatility all have a huge impact on these processes in terms of operational constraints.Therefore the optimisation and control of beneficiation processes must take into account many factors other than pure process variables such as flow rates and levels. For example, commodity prices and client requirements all need to be added to the control problem, which together with incomplete process knowledge and non-linearities etc., make automation and optimisation extremely difficult.The ideal solution is to have a controller which in addition to performing full non-linear constrained optimal control can at the same time take into account other non-process factors such as price and client satisfaction."

Jan 1, 2003

By Robert J. Timko, Charles D. Taylor, Edward D. Thimons, Tom Mal

A test system was developed for measuring airflow in the National Institute for Occupational Safety and Health (NIOSH) ventilation gallery using a three-axis ultrasonic anemometer. The gallery was used to simulate face airflow conditions in underground mines having a blowing curtain. Airflow data collected at multiple sampling locations between the face and the end of the curtain were used to draw airflow profiles for different curtain setback distances, intake flow quantities and entry widths. In addition, methane was released at the face, measured at the sampling locations, and displayed as methane distribution in the area between the curtain and the face. Entry geometry had a significant effect on airflow patterns, and the flow patterns affected the distribution of methane in the entry. Flow measured at and parallel to the face was a good predictor of methane dilution and removal within two feet of the face.

Jan 1, 2005

By Chen Shuwen, Yao Zhihua

In the process of thickening dewatering_the motion state of two- phase flow in a thickener has a very great influence on thickening efficiency. The investigation was made using copper mill tailings. In this investigation the authors explored the formation conditions and motion range of density current in the thickening process by model experiments, and analyzed the influence of density current on thickening efficiency. The results have shown that the formation of density current has relations with the structure parameters of a thickener and thickening process. The density current and its forming location affect thickener’s working efficiency. The author measured the motion state of two- phase flow in a 53-m dial. thickener for copper mill tailings under its operation conditions and analyzed the density distribution and motion state of two-phase flow in the thickener. The results obtained by the industry tests have shown that the motion state of two- phase flow in the thickener can be greatly improved by modification of its structure, achieving a great improvement in its thickening efficiency. It is concluded that, a thickener’s working efficiency depends on the formation and motion range of density current in it, which is of great importance to designing and establishment of thickener’s working parameters.

Jan 1, 2003