Search Documents

By W. S. Sanner

Anthracite was used extensively as a fuel in iron metallurgy from 1840 to 1880. In 1874, 226 of the 680 blast furnaces in the United States were operating on anthracite and producing almost one-half of the Nation's pig iron. However, by 1890, railroad expansion, the development of western iron-ore reserves, and the growing use of coke decreased the importance of anthracite as a metallurgical fuel. As a result, the last blast furnace designed exclusively for anthracite use was built in 1891. Because of the increased energy requirements of our expanding national economy, the abnormally high demands during national emergencies, and the proximity of anthracite deposits to eastern steel-producing areas, interest has grown in again using anthracite in iron metallurgy. Estimates of anthracite reserves indicate a 300-yr. supply at a production rate of 30 million tons per year. These large reserves dictate the development of an adequate technology for the use of anthracite by the metallurgical industry.

Jan 1, 1961

By H. Krogerus, P. Jokinen, T. Lintumaa

The energy consumption and recovery of chromium are important economic factors in ferrochrome production. Outokumpu has a lot of experience of the reduction behavior of the sintered pellets in industrial-scale furnaces and also on the grounds of numerous laboratory and pilot-scale investigations. Sintered pellets have shown a superiority over lumpy ore and briquettes made of the same chromite grade. The good performance of the pellets has also resulted in investigations on the reasons for such a performance. In this study, the factors affecting pellet behavior in smelting furnace were investigated. This study is divided into two sections, i.e. the investigations were on the factors affecting solid state reduction and on the factors affecting reduction under melting. These tests were performed by means of thermo gravimetry and by smelting tests. The correlation between the pellet characteristics and reduction behavior was shown and its influence on industrial-scale furnaces was discussed. Factors worth of consideration are for instance, the extent of oxidation during sintering, slag formation and chemistry in respect of molten state reduction, and the grain size of the chromite mineral in the raw material in respect of kinetic reasons (retention time in smelting).

Jan 1, 2007

Iron production in one year exceeds that of all other metals combined in ten years. It is a huge industry that started from a modest furnace producing one - two kilograms metal per day to a gigantic reactor producing 10 000 tons per day. The major milestones of these developments are reviewed.

Jan 1, 1999

By D. J. Dollhopf

The objective of this five year study was to investigate the means of establishing non-polluted ground-water and root zone systems in areas where surface mining intercepts physiochemically unsuitable overburden materials. Overburden may need to be sampled on a 60 m grid in order to delineate materials unsuitable for reclamation and to accurately implement selective handling operations. Unsuitable overburden materials were buried successfully in a dragline operation with a minimum of delays, but costs were increased 12 to 53%. After three years the buried material remains above the reestablished aquifer and below the root zone. Construction of a clay cap over the buried material may not be required in semiarid environments. It was shown that some unsuitable overburden materials do not have to be special handled. When inhibitory material constituted <5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile due to mixing/dilution processes. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. At least a portion of the postmine aquifer had hydraulic conductivity rates lower than the premine system, indicating the reestablished aquifer may, in part, conduct ground water very slowly. Postmine ground-water chemical quality in spoil materials had poorer quality compared to premine ground water.

Jan 1, 1981

By John Feddock

A recent increase in energy demand has resulted in the rapid growth of coal consumption in the People?s Republic of China (PRC), which is the largest coal producer and consumer in the world. Reportedly, the safety issues in Chinese coal mines have been improving, but the number of fatalities and serious injuries continues to be alarmingly high. The number of fatalities from catastrophic accidents have prompted researchers to review the Chinese mine safety situation and to look for potential solutions. Marshall Miller & Associates, Inc. (MM&A), along with various collaborators, has investigated these issues as part of its work on various projects in the PRC and has discussed the concerns with relevant Chinese officials. Preliminary investigations by MM&A of coal mine accidents during 2001?2006 in the PRC indicate that 65%-78% of the total fatalities were the result of gas explosions and roof falls in underground mines. Even though the drainage of methane has been practiced for decades, current practices do not always produce satisfactory results due to technical constraints and equipment limitations. Based on prior experience of in-seam degasification at the Daning Coal Mine located in Shanxi province, MM&A believes that in-seam directional drilling technology can be a viable solution to degas the low-permeability Chinese coal deposits. This paper 1) reviews current Chinese coal mine safety conditions, 2) analyzes the advantages/disadvantages of current degasification practices in China, and 3) presents the pre-mining degasification practices for the longwall panel at the Daning Coal Mine.

Jan 1, 2007

By Yi Luo

A longwall mining operation went under a tall, self-supporting and free-standing wireless communication transmission tower. In anticipation of that the ground subsidence process might affect the transmission tower, the mining company took a proactive approach to mitigate the expected subsidence influences. The efforts include prediction of surface subsidence process at the location of the tower, assessment of stability, structural integrity and functionality of the tower structures, and design and implementation of mitigation measures. The intension of this paper is to demonstrate the techniques that can be used to assess and mitigate the subsidence effects on tall self-supporting and free standing tower structures.

Jan 1, 2008

By John M. Devine

The severe corrosion of equipment that is caused by the presence of hydrogen sulphide in oil and gas has been described in detail by several authors.5 Such corrosion, termed "low-temperature hydrogen sulphide corrosion", presents a somewhat different problem from the "high-temperature hydrogen sulphide corrosion" that is encountered in refinery operation and

Jan 1, 1932

This publication summarizes, for potential contractors and other interested parties, the research, development, and demonstration contract projects programed by the Bureau of Mines for fiscal year 1979 (October 1, 1978-September 30, 1979) under its Mine Health and Safety Research program. The objective of these projects is to provide an ordered and sequenced series of advances toward the Bureau&apos;s overall goal of providing the system technology required to create a healthier and safer working environment for the Nation&apos;s miners.

Jan 1, 1979

By Thomas M. Gurtowski

This paper presents a summary of allowable bearing pressures and skin friction values that have been used to design drilled pier foundations for support of high-rise structures in downtown Seattle, Washington. These design parameters are based upon a review of geotechnical reports and records of more than 20 building projects. The following pages present a description of the soils encountered at these sites including foundation bearings soils, and design bearing and friction values. The accumulated data is summarized in Table 1, and the locations of the buildings are shown in Figure 1. A detailed description of the construction of two belled drilled piers are presented illustrating typical methods and procedures used in downtown Seattle. The two cases are from the Washington State Convention and Trade Center (WSC&TC). SEATTLE AREA SOILS The Puget Sound area was subjected to several major glaciations during the Pleistocene Epoch. Glacial ice originated in the cordilleran and coastal mountains and the Vancouver Range of British Columbia. The maximum southward advance of ice reached the area about halfway between Olympia and Centralia. As a result of these glaciations, the Puget Lowland was filled to significant depths by glacial and non-glacial sediments during the Pleistocene.

Jan 1, 1990

By A Liu, T Ren

Gas explosion in underground coal workings can pose a serious threat to the safety of mine workers and the entire mine operations. Gas explosion is a very complex thermal-chain reaction in a confined underground environment. Based on combustion and explosion theory, three dimensional (3D) computational models were developed to simulate mine gas explosion flame and overpressure wave propagation in a single entry gateroad in underground coalmines. Six different explosion scenarios were modelled and compared with large scale experimental results and AutoReaGas simulations. Model validations show that the use of shear-stress transport (SST) k-? model together with eddy-dissipation model (EDM) produces good agreement with both experimental and AutoReagas simulation results. Modelling results demonstrated that the changes of temperature versus time can be divided into four stages, ie&#160;the initial condition stage, and periods of warm-up, active burning, and burnt-out. Assuming a limited volume of methane is involved in the explosion, the maximum temperature decreases as the distance increases from the explosion point, with the highest temperature reaching about 2460 K. Modelling results show that the evolution of the explosion flame shape experiences four typical stages, ie&#160;spherical flame, finger-shape flame, flame with the skirt touching the side walls (ribs) and tulip flame, which are similar to the pattern of a duct explosion. The pressure in the gateroad remains the same as the initial value before the arrival of the explosion wave and then increases rapidly to the maximum value. Modelling results from this study will be used for the design of explosion arresting devices and mine seals in underground coalmines.CITATION:Liu, A and Ren, T, 2017. Computational simulation of gas explosion and its propagation in single entry gateroad, in Proceedings Australian Mine Vent Conference 2017, pp 181–188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By S. K. Kawatra, S. J. Ripke, T. C. Eisele

"An estimated 600,000 tons of bentonite clay are used annually in the U. S. as binder for production of iron ore concentrate pellets. Since this is a significant cost item for the plants, and the addition of bentonite to the pellets contributes undesirable silica into the finished pellets, there is considerable incentive for finding methods to reduce bentonite use. One way to reduce bentonite levels is to selectively use those bentonites that are most effective in this application, so that a lower dosage will still produce a sufficiently strong pellet. Unfortunately, there are no satisfactory methods available for accurately predicting which bentonites are actually most effective, short of using them to actually make pellets. One of the popular methods for attempting to evaluate bentonites is the “Plate Water Absorption” (PWA) test. While some plant operators accept the PWA results as indicating the relative quality of bentonites, others disagree and claim that, over a fairly broad range of values, PWA does not correlate with bentonite performance.Since both Ca+2 and Mg+2 ions are known to reduce the swelling and water absorption capacity of bentonite, it was believed that the presence of these ions in plant recycle water could be changing the bentonite performance. Since the standard PWA test uses only distilled water for its measurements, it could not detect these effects. Experiments were therefore carried out on a number of different bentonites using a modified PWA tests, with plant recycle water replacing the distilled water. These experiments showed little effect of the plant water on the PWA value, and chemical analysis of the water showed that the levels of dissolved salts were quite low.Water and accompanying salts were then extracted from a magnetite concentrate filter cake by rinsing with distilled water. Analysis of this water showed an extremely high level of dissolved salts, particularly salts of calcium and magnesium. When concentrations were compared with the recycle water from the plant filters, it was determined that levels of Ca+2 and Mg+2 retained in the filter cake were over 500 times higher than levels in the recycle water. This extreme elevation of soluble salts in the filter cake is believed to be due to adsorption of these ions into the electrical double layer of the magnetite particles."

Jan 1, 2003

The Bureau of Mines conducted large-scale laboratory copper ore leaching tests to enable improving copper recovery from large dump-leaching operations. This was done by comparing leaching progress when copper was recovered from recycled leach liquor either by cementation or by solvent extraction. Copper was leached from 7-ton ore samples at room temperature using pH 2 ferric sulfate solutions. With are samples containing 11 percent minus 0.5-inch fines, no marked advantage in using either of the copper recovery methods was evident after 416 days of leaching. With ore containing 32 percent minus 0.5-inch fines, solvent extraction of copper was advantageous in that 60 percent of the copper was extracted after 568 days, whereas only 48 percent of the copper was extracted when cementation was used. Less acid was consumed during leaching when solvent extraction, rather than cementation, was used for copper recovery. Iron, contributed by cementation with scrap iron, plugged the ore bed containing 32 percent fines.

Jan 1, 1981

By A. C. Wilson

In 1991, local prospector C. ?Mickey? Clement recovered at least three alluvial diamonds from the Michipicoten River. Two of these stones were sent to the Department of Mineralogy, Royal Ontario Museum, where they were identified as industrial grade diamonds with weights of 1.05 and 1.13 carats. Both stones were described as frosted and graphite-inclusion riddled. In 1995, prospector Sandor Surmacz and geologist Marcelle Hauseux discovered diamonds in bedrock approximately 20 km north of the Michipicoten River. An 18.1-kg bulk sample of a xenolith-rich lamprophyre, taken from an outcrop at the side of the Trans Canada Highway north of Wawa, yielded 1 macro diamond and 5 micro diamonds. All but one was gem quality (Sage 2000). Since then, more than 36 occurrences of diamonds in bedrock have been reported in an approximately 30 km2 area centred 20 km north of the town of Wawa. The occurrences are hosted within a sequence of unusual, Archean-aged, heterolithic breccias previously considered to have no economic significance. Ten kimberlite occurrences also have been confirmed in the Michipicoten greenstone belt in the last 5 years. Two of these kimberlites are diamondiferous. To date, expenditures on property acquisition and diamond exploration in the Wawa are estimated at $120 million (CAN). This paper summarizes the geological observations made on these occurrences and discusses including the relationship between the occurrences and the regional geology.

May 1, 2003

By A. M. Tonnos

Underground mining has yet to see an industry wide solution for control of their ventilation systems due to the complexity and sensitivity of the underground environment. Complexity arises from multi-level, multi-zone operations and sensitivity is associated with the impact that changes in equipment status and output have on air flows and quality throughout the mine. Our approach to solving this challenge incorporates system modeling and industrial control systems in a unified architecture. Although this approach can be applied to other processes and industries, this paper will cover the theoretical and practical aspects of an integrated model-control system (MCS) as it applies to underground mining ventilation.

Jan 1, 2009

By Thomas A. Phillips

The Bureau of Mines presents an economic evaluation of its leach- electrolysis process for recovering lead from galena concentrate. In this process, galena concentrate is leached at 200° F with a ferric chloride-brine solution to extract lead while leaving sulfur in the residue, which is discarded. The solution after leaching is concentrated and cooled to 100° F by vacuum evaporation to crystallize lead chloride from which metallic lead and chlorine are produced by fused-salt electrolysis. Chlorine is used to regenerate the spent leach solution before it is recycled. A cost estimate was prepared for a plant capable of producing 300 tons per day of lead, 330 days per year. The fixed capital cost on a third-quarter 1977 basis Fs $27,500,000, and the estimated operating cost without a charge for the concentrate is 4.9 cents per pound of lead product. Assuming a selling price for corroding-grade lead of 31 cents per pound and a charge for the concentrate of $332 per ton, the interest rate of return on investment after taxes is 16 percent. The leach-electrolysis process, therefore, appears to be economically attractive under the assumed market conditions.

Jan 1, 1978

By J. M. Weehuizen

Complete details are given of the drilling method by which two shafts were sunk at the new Beatm&apos;x mine of Staatsmijnen in the Netherlands. The nature of the rock strata in the Dutch mining district determined choice of the drilling rather than the freezing method. Data for each step and details of the equipment used are given in the illustrations. Staatsmijnen was founded in 1902 with government financial backing, but it is run as a private enterprise, on a commercial basis, with the normal fiscal obligations. The company now has four mines in operation with annual outputs amounting to 7 1/2 million tons of coal. In 1952 it was determined that a new mine—the Beatrix—would be opened. Details of the shaft-sinking operation are described in this paper. SHAFT LOCATION The coal-bearing carboniferous rock in the Dutch mining district is overlain almost completely by soft water-bearing strata, which at the site of the new shafts are about 1600 ft thick. The sinking of the new shafts through this soft water-bearing overburden (Fig. 1) is a costly and time-consuming affair. From the two availaible sinking methods: 1) Poetsch&apos;s well known freezing method or 2) the drilling method of Honigmann-de Vooys, the latter was preferred, not only because of its relative cheapness, under the prevailing conditions, but primarily because by using the drilling process, a special type of shaft lining of steel, concrete, and bitumen could be used. The new shafts, located 330 ft apart, have an inner diameter of 18 ft, 4 1/2 in. The boreholes, which have a diameter of 25 ft and which were drilled through nearly 1600 ft of overburden and some 100 ft of carboniferous, each contain more than 29,000 cu yd—by far the largest in the world. DRILLING METHOD The drilling method is based on the use of mud-flush—a thin mixture of clay and water—to keep the borehole filled during the entire drilling period and during insertion of the lining (Fig. 2). The pressure of the mudflush against the borehole wall is greater than that of the water in the surrounding

Jan 1, 1961

By Rashmi Ramesh

Zinc oxide nanoparticles and nanostructures form an active area of research in the recent years. It can be doped to modify electronic, optical and other properties. Synthesis and characterization of zinc oxide is of extreme importance in order to understand the structure property relationship in this material which is now being considered of importance next to carbon nanotubes. Microstructure of zinc oxide nanomaterial is extremely sensitive to the preparation conditions. Nanocrystalline pure and Mn and Mg doped zinc oxide samples were prepared by wet-chemical method under different growth conditions. The samples were investigated for crystalline phase, microstructure, morphology and luminescence characteristics. The effect of Mn and Mg doping on the characteristics of ZnO have been discussed.

Jan 1, 2010

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nonmetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963

By Lee W. Abramson

Performing risk analyses on tunnel projects has become common place and on many projects it is required from an owner or regulatory perspective. After the project is planned, designed and constructed, the data concerning identified risks, assumptions, costs, probabilities and mitigations is generally long forgotten and buried in some file somewhere. A study was performed comparing predicted risks versus actual events on several recently constructed tunnel projects. Probabilities and costs for selectively common risks on tunnel projects have been studied and re-evaluated. Conclusions are presented that can guide future projects and the veracity of the tunnel risk analyses performed.

By N. M. Safaya

Moderate to acute deficiency of plant available phosphorus is very common in western coal mine spoils and topsoils. Although some of the spoils are known to contain seemingly adequate amounts of total phosphorus, the plant available phosphorus is so low that it constitutes a serious plant growth limiting factor in the mined lands. For the revegetation of these spoils, the use of species, varieties and ecotypes exhibiting greater efficiency for P uptake and utilization, or conversely, lesser susceptibility to P deficiency would be highly desirable. To identify such plants, quick and adequate methods of screening germplasm should he available. In the present growth chamber study several plant species were screened using continuous flow culture and spoil culture systems to provide information on their relative susceptibility. In flow cultures, P was maintained at 0.25, 2.5, and 25 moles; while in spoil cultures it was applied at 0, 25, and 75µg/g to a P-deficient spoil. Phosphorus deficiency symptoms appeared in alfalfa cultivars, birdsfoot trefoil, emerald crownvetch and yellow sweetclover within 7-10 days upon transfer of their seedlings to U.25 or 2.5 µM P solutions. Burning bush and Russian thistle, found abundantly as pioneering species on mine spoils, showed no deficiency symptoms; their shoot dry matter yield in the 0.25µM P treatment was 24% and 36%, respectively of their maximum yield obtained with 25 µM P. However, the percent increase in the dry matter yield of legumes with 0.25 µM P ranged from 7-13% over their maximum yield. With the increase in solution P concentration, the root dry weight ratio in the legumes increased from an average of 0.22 to 0.43, while in the weeds from 0.14 to 0.30. The low susceptibility of Russian thistle to P deficiency was also demonstrated in the spoil culture experiment. Legumes showed greater response to P-fertilization on the spoil than did the two weeds. With increasing concentrations of P in the solution, the root weight ratio of all the species decreased. At 25 µM P, weeds invested only 14% of their total dry matter yield in the root fraction, where as legumes and grasses invested as much as 24% and 33% respectively. Weedy species averaged higher P concentrations than the legumes and grasses. The mean P concentrations of alfalfa cultivars were the lowest among legumes. In general, P concentrations increased with the increase in P supply. In the flow culture system, P supply increased the Ca levels of legumes. The mean Mn concentrations were highest in the weedy species. The increases in P supply decreased Zn levels in all of the species. File effects of P fertilization on the tissue concentrations of Mn and Zn in spoil culture were similar to that of flow culture system. From this preliminary study, it may be concluded that the continuous flow culture system is efficient in rapid screening of a large number of species under controlled conditions for their efficiency in adapting to mineral stresses.

Jan 1, 1982