Search Documents

By Eric M. Klein

As part of the Woodrow Wilson Replacement Bridge project several damaged wetland and environmental areas were to be mitigated. One of the mitigation projects consisted of constructing a Denil fish ladder around Peirce Mill Dam in Rock Creek National Park, Washington, D.C. The dam is a historic structure operated by the National Park Service. The fish ladder is located between the east abutment of the dam and Beach Drive, a major collector road. Construction of the fish ladder required removal of a portion of the east abutment and an excavation that extended about 22-ft below the pavement of Beach Ave. It was not possible to close Beach Drive except for very brief intervals or at night; therefore, a support of excavation system that would minimize disruption to the public was required. The high groundwater required that the groundwater be cut off prior to excavation; the random rubble and soil fill, and shallow but erratic rock surface precluded driving sheet piling. A jet grout system was selected because the grout probe could penetrate the rubble fill, stabilize a variety of soil conditions, and cut off the ground water prior to excavation. It was not possible to construct a stable wall without tiebacks or soil nails. Given the schedule and tight working conditions it was decided that soil nails through the jet grout wall facing would be the most cost effective method, as it did not reduce the working space as rakers would and would be more cost effective than prestressed tiebacks.

Jan 1, 2006

Collecting the clay fraction of active stream sediment from a flowing stream for geochemical analysis i a difficult process. One either takes a sample of dry fine-grained sediment from the stream bank (dry weather and dry sample are uncommon in parts of New Zealand and Tasmania), or dredges up a sample of sand and mud out of the stream.The latter method produces a soggy ample bag full of mud and sand, with varying amounts of gravel, depending on the size of the stream. The water can be filtered from such a sample by means of a Buchner filter funnel, but is difficult to obtain a vacuum in the bush. This problem can be solved by using a small hand- queeze bellows such as used in priming petrol pumps on outboard petrol motors. The common laboratory hand bellows is not powerful enough.A 70 mm diameter two-piece polythene Buchner filter funnel (Fig. 1) can be used. A length of rubber tubing is fitted around the inlet valve of the hand bellows and this valve is then jammed into the pipe at the bottom of the filter funnel (the polythene pipe may be trimmed with a knife to fit over the inlet valve of the bellows). The vacuum is generated and maintained by squeezing the hand bellows.The technique of collecting a sample of the clay fraction is to dredge a sample of the fine-grained active stream sediment out of the stream with a container, such as a plastic mug. The sample is agitated to get the clay fraction into suspension and the muddy suspension is then decanted into the Buchner funnel. The desired clay fraction is obtained as a thin film on the filter paper.If the "fines" are also required, a filter of nylon bolting cloth (stretched across the mouth of a short length of 80 mm diameter polythene pipe and attached by rubber bands or a concentric polythene pipe) can be placed over the mouth of the Buchner funnel and the whole sample of stream sediment...

Jan 1, 1969

By P. A. Plunkert, D. E. Morse, L. McCartan, S. F. Sibley

The average annual growth rate of real gross domes-tic product (GDP) from the third quarter of 2001through the second quarter of 2003 in the United States was about 2.6 percent. GDP growth rates in the third and fourth quarters of 2003 were about 8 percent and 4 percent, respectively. Many other indicators reflected a rebounding U.S. economy — rising consumer confidence, higher retail sales, greater industrial production and more housing starts. Inflation also reached a 38-year low in 2003. The upward trends in many sectors of the U.S. economy in 2003, however, were shared by few of the mineral materials industries. Annual output declined inmost non fuel mining and mineral processing industries, although there was an upward turn toward yearend as prices began to increase (Table 1).

Jan 1, 2004

E. W. Stutchbury (Internationa~ Oombustion Aust. Ltd.) : Mr. Callcott made particular mention in his paper of erosion in primary air fans which are placed after the mill discharge. He adds that subsequent reduction in plant performance and resulting increased maintenance costs occur. It is generally assumed that this statement is substantially correct as the fan handles the complete output from the mill, but with modern materials, reduction in performance and subsequent .maintenance are not now a problem. This consideration of handling the pulverised coal in the fan is more than offset by the advantage of operating the mill under suction which results in cleaner operating conditions, simpler feeder arrangements and elimination of complicated seals on the mill.and feeder unit. It should be specially noted that whereas mill exhausters in the past have used chequer plate blades (sometimes with the addition of hard facing by electrode deposit) it is modern practice to provide fan blades of up to 1 in·. thick Ni-hard suitablyheat treated, with the circumferential section of the fan also in Ni-hard. By the use of this material large power...

Jan 1, 1957

By J. Douglas, W. T. Ford, G. E. Henderson, I. F. Roebuck

An implicit numerical method is presented for simulating the differential and algebraic relations governing one-dimensional three-phase flow in porous media. The method is based upon compositional representation of the hydrocarbon system. Variable physical properties and water-oil capillary forces are included in the formulation; however, the effect of gravity is ignored. The effects of changing composition and mass transfer are considered through the use of known phase behavior concepts and correlations. The differential and algebraic equations and the numeric approximations to these equations are presented, and the computing algorithm is discussed in detail. This method is used to simulate a single-phase, two hydrocarbon-component gas displacement laboratory experiment. The method is also applied in simulating a solution gas drive and a gas injection problem using a reservoir oil represented as a nine-component mixture. For comparative purposes, the latter two problems also are examined with a one-dimensional volumetric model. The results of the simulation of the laboratory experiment demonstrate the relevance of this method to problems wherein the effects of mass transfer significantly enter the displacement process. The comparison of the results of the volumetric and compositional methods applied to a reservoir system illustrates not only the advantages and benefits derived from examining the hydrocarbon system composition, but also the necessity of this approach in application to a general reservoir problem. INTRODUCTION The advent of large memory, high-speed digital computers enabled reservoir engineers and mathematicians to pool their knowledge in the development of sophisticated techniques for the prediction of oil and gas reservoir performance. These techniques have progressed from volumetric and trend analysis calculations to the development of "mathematical models", or reservoir simulators. These latter models, in general, utilize finite difference approximations to the rather complex partial differential equations that mathematically describe the physics and thermodynamics of fluid flow in porous media. Many forms of this "model" type are available today, and much of the recent literature has been devoted to either improving known methods or developing new techniques for use in these prediction methods. The more advanced techniques in use at this time consist of the solution of differential and algebraic relations that describe a reservoir geometry in one, two or three dimensions and that incorporate reservoir hydrocarbon and water fluid systems that obey specified physical laws, having properties that might easily be measured in the laboratory. This type of model utilizes formation volume factors and other volumetric data, expressed directly as functions of pressure, to represent the reservoir fluid system. Experience gained with this type of simulator, commonly known as a "beta-factor model", has indicated that the approach has many outstanding defects, most of them due to the assumption that those properties measured in the laboratory completely describe the behavior of the fluid system throughout the life of the project under study. The effects of varying hydrocarbon composition and mass transfer between the phases of this hydrocarbon system must, by definition, be ignored. These defects, which may often be ignored in

Jan 1, 1970

By J. Samir

The objective of this study is to simulate the isothermal filling up of moulds by a RTM process when adopting CV/FEM and VOF method and when also taking into account the presence of obstacles coupled to the effect of the thickness and reinforcement layers variation. The codes developed intended to ensure an optimal positioning of the injection points and of the vents and also to determine optimal injection pressures, in order to minimize the cycle times. These codes use a mesh generator proper to the team, allowing a discretization of the domain in triangular unstructured elements, with the possibility of a local refinement and inserts inclusion.

Jan 1, 2009

By Jinwu Kang

The hydraulic turbine blade of the matensitic stainless steel (Cr13%,Ni5%,Mo1%) is a kind of large and curved shape, which is susceptible to deformation in both casting and heat treatment processes. The coupling analysis of heat transfer, phase transformation and stress in heat treatment process of the turbine blade for Three Gorges Project is carried out by using Deform-3D software. Its temperature fields, phase fields and stress fields in heat treatment process are obtained. And its deformation is predicted. In the cooling process of normalizing, the blade exhibits relatively large deformation. Based on the stress analysis and deformation prediction in heat treatment process, an algorithm for the determination of reverse deformation of the blade casting in heat treatment process is presented. And the reverse deformation distribution of blade is obtained.

Jan 1, 2010

By Hans Janzon, Ernst Buechi

INTRODUCTION The headrace tunnel in Amlach is part of a hydro electric power scheme near the city of Lienz in south west Austria. The project is owned and developed by Tiroler Wasserkraftwerke AG, the regional electrical supply utility. The construction work was divided into seven contracts for the entire scheme. The power output will be 60 MW, this being developed from a head of 370 m and water flows of 20 m3/s. The water will be tapped from the river Drau and lead through a 22 km long headrace on the south side of the Puster valley through the Lienzer Dolomiten mountain range. Contract No. 4, which is a joint venture between Mayreder, Züblin, Strabag, Rella and Innerebner, involves the construction of 13.5 km of the headrace. It was decided to bore this from one single adit, which probably makes it the longest pressure tunnel driven from one side by a TBM. (See Fig. 1.) For the tunnelling an Atlas Copco Jarva MK 12 TBM was chosen. The excavation diameter is 3.90 m, with the final lined diameter being in the range of 3.20 to 3.40 m. The back-up is a 145 m long single track rail system supplied by Mühlhäuser (Germany). Side-tipping cars with a capacity each of 8.2 m were used for removing the muck. One California switch was attached to the back-up after 3,000 m, and a second fixed switch was installed after 8,000 m of boring. 3 m long

Jan 1, 1987

By B Hartmann

In 2003, Independence Group NL purchased the Long Shaft Nickel Mine complex (Long) in Kambalda, Western Australia. Lightning Nickel, the nickel operating arm of Independence Group, faced considerable challenges operating the mine, with the most significant challenge being able to prove that the remnant ore at Long and the associated orebodies could be mined safely and efficiently. Given the seismic history at Long, the magnitude of these challenges could not be underestimated. In an effort to achieve 100 per cent extraction of the flatter orebodies, traditional methods such as room and pillar were dismissed. A method consisting of transverse sills, butting into each other was proposed. To stop fill material from the first sill rilling into the adjoining sill, it was proposed to backfill the sills with pumped cement fill. The capital cost of the fill plant was estimated to be in excess of $1.5 million and the cost for cement alone was $1.0 million per annum. Shotcrete was already an extremely useful tool in dealing with the widely variable stress environment, but was to be used in an innovative manner that would enable the full extraction of a tabular section of the Victor South orebody. A layer of shotcrete, approximately 100 mm thick, was to be sprayed on the up dip wall of the initial development sill. The sill was to be backfilled with ænormalÆ development waste and ætoppedÆ with sand backfill. The next sill, ie slightly up dip and alongside, was to be mined along the shotcrete boundary wall. With respect to wall stability, the premise was that the shotcrete wall would stay in place and prevent the backfill (development waste and sand) from rilling into the adjoining development. It was also proposed that any breaches of the shotcrete wall would be repaired using shotcrete before substantial inflow of backfill into the ænewÆ development. This paper describes the development and implementation of this mining method, as well as some of the associated financial aspects.

Jan 1, 2008

By P. H. S. W. Kulatilake

To exploit an underground mine effectively and safely, it is important to have a good understanding of the geotechnical behavior around underground excavations made in the mine. The aim of this study was to investigate the geotechnical behavior around a tunnel excavated in a metal mine in China at the three-dimensional level. Using the information available on lithology, geological structures, in-situ stress measurements, physical and mechanical properties of intact rock, discontinuities and interfaces between different rocks, a three-dimensional numerical model was built by using the 3DEC software to simulate a tunnel excavation under a high in-situ stress condition. Effect of the discontinuity network, possible intact rock and discontinuity parameter variability, representation of rock masses as discontinuum or continuum material and rock support system on the deformation, stress, failure zone and stability around the tunnel was investigated. A very good agreement was obtained between the collected field deformation monitoring results and the results of the conducted numerical stress analyses.

Jan 1, 2012

"Exploitation of an ore deposit can be optimized by adapting the beneficiation processes to the properties of individual ore blocks. This can involve switching in and out certain treatment steps, or setting their controlling parameters. Optimizing this set of decisions requires the full conditional distribution of all relevant physical parameters and chemical attributes of the feed, including concentration of value elements and abundance of penalty elements. As a first step towards adaptive processing, the mapping of adaptive decisions is explored based on the composition, in value and penalty elements, of the selective mining units.Conditional distributions at block support are derived from cokriging and geostatistical simulation of log-ratios. A one-to-one log-ratio transformation is applied to the data, followed by modelling via classical multivariate geostatistical tools, and subsequent back-transforming of predictions and simulations. Back-transformed point-support simulations can then be averaged to obtain block averages that are fed into the process chain model.The approach is illustrated with a ‘toy’ example where a fourcomponent system (a value element, two penalty elements, and some liberable material) is beneficiated through a chain of technical processes. The results show that a gain function based on full distributions outperforms the more traditional approach of using unbiased estimates."

Jan 1, 2015

By P Paredes, T Leaño, D Gajardo, C Tramón, S Peñaloza

The definition of an ore handling system and its consequent layout design is of crucial importance in cave mining projects. It not only represents the main driver in the production capacity and reliability of the mining system, it is also a fundamental variable in the footprint’s development time and cost.In recent decades, load-haul-dump (LHD) tramming distance optimisation through the allocation of several orepasses inside the footprint has been the most common practice in ore handling system layout definition at Codelco’s operations. Today, the improvement of existing technology, such as higher-capacity LHDs and jaw-gyratory crushers, and intensive preconditioning techniques to improve fragmentation allow the conceptualisation of simple and highly productive ore handling system layouts for wide caving areas that avoid the complexity and high cost of developing numerous orepasses inside the footprint.The initial macroblocks of the Chuquicamata underground mine project (PMCHS) consider an ore handling system layout in which LHDs dump into orepasses located inside the footprint area. The ore is then transferred into crusher chambers located below the production level, where it is crushed by jaw crushers and then conveyed to surface. In an effort to reduce development time and costs, a new ore handling system layout for the PMCHS experimental macroblocks was engineered using improved technologies and techniques in a simpler mining system. This paper compares the new ore handling system layout for the project’s experimental macroblocks with the traditional LHD-orepass layout in terms of production capacity, reliability, development time and cost.CITATION:Paredes, P, Gajardo, D, Leaño, T, Peñaloza, S and Tramón, C, 2016. Simplifying the ore handling system through the use of current technology at Chuquicamata underground mine project, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 571–584 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By P. Dhar, H. R. Kota, M. Thornhill

Precipitated calcium carbonate is used as a filler and coating material in the manufacturing of paper because of its high brightness and light scattering characteristics. However, beneficiated calcite has similar potential, given the fact that the industrial specifications are already achieved. For paper industries, the requirement is that the desired product should be pure and have a brightness of 93 to 95 percent. A very-high-grade calcite deposit of around 92 percent is located in the north of Norway, which is used as the raw material for ground calcium carbonate (GCC) feed for the paper industries. There is a substantial amount of calcite resource, which has pyrite and pyrrhotite as major impurities. These sulfides, even when present in minor concentrations, impart color to the end product (paper). Removing these minerals is estimated to increase utilization of the deposit by 10  percent, which represents several million tonnes of calcite marble. Due to the requirement for environmentally friendly reagents and chemicals by the mineral industry, fatty di-amines are being tested for pyrite and pyrrhotite flotation. The interaction mechanism of diamine with the main components of the ore were studied and optimum conditions for removal of sulfide impurities are outlined.

By Ronald P. Hollenbeck

Shales in the Appalachian Region of Kentucky and Tennessee were sampled and tested to determine their use as raw materials for the manufacture of lightweight aggregate by the rotary-kiln method. Nine samples were obtained from eastern Kentucky and 143 samples were obtained from eastern Tennessee. As a result of preliminary testing of these samples, two sources in eastern Kentucky and 11 sources in eastern Tennessee were resampled for rotary-kiln tests. The rotary-kiln tests showed the two sources in Kentucky and seven sources in Tennessee contained shale that would produce satisfactory aggregate. Lightweight aggregate processed from these nine sources was tested in concrete shapes and was found to be suitable for use in structural concrete.

Jan 1, 1968

Microfluidic Solvent Extraction for Mineral Processing of Copper Leach Solutions

Sep 13, 2010

By Sydney H. Ball

I. INTRODUCTION. DURING the past 50 years the attention of mining-men has been turned to Africa, and within the past decade prospecting-expeditions sent into Central Africa have resulted in the opening-up of several mines. Having recently spent two years in the Belgian Congo for the Société Internationale Forestiere et Miniere du Congo, it is our purpose to outline briefly the mining-conditions in that part of Central Africa. Before it became, in 1908, a Belgian colony, this region was known as the Congo Free State. II. LOCATION AND AREA. The Belgian Congo lies in southwestern Central Africa, west of the continental divide, is illustrated in Fig. 1. It has a coastline of but 20 miles on the Atlantic, but widens rapidly eastward to points 5° north and 14° south of the equator. Its area is 908,000 sq. miles, which is almost one-quarter that of the United States and Alaska, or more than one and one-half times that of Alaska. Stated in other terms, its area is nearly one-third that of the United States, exclusive of Alaska and the insular possessions, or more than that of all the United States east of the Mississippi river. III. TOPOGRAPHY AND DRAINAGE. From north to south, Africa is made up of three topographic elements: 1, the Atlas mountains, a highly-accentuated region

Apr 1, 1910

By P. Bracher

Most efforts to mechanize low seam (narrow reef) mining of platinum ore are presently based on board-and-pillar methods with1.6?1.8 m in reef excavation. This paper attempts to substantiate the benefits of low profile mining: primarily improved head grade with resulting reduced tailings losses. Board-and-pillar equipment supplied by DBT, facilitating1.1?1.2m mining height has been in operation in an Anglo Platinum mine since September 2001. Major aspects of the equipment, battery scoops (LHDs) and rotary bolting rigs, are described and presently achieved results reported. The medium term industry goal is rock breaking without the use of explosives. An outline of present DBT developments is presented.

Jan 1, 2003

By Bruce Vandenberg, Andy Battfay, Don Lake, Steve Conway, Jeff Yorsz

"High-speed motion pictures are an invaluable resource for blasting analysis. Whether processed by the human eye or a computer, this imagery can provide important insight into a blast and its effects.While certainly popular, traditional high-speed film cameras hamper this process. Instant feedback is not available since film requires developing and, relevant in the case of automated analysis, film isnot immediately compatible with a computer. With these facts in mind, a new high-speed video camera system, the SVCSOO, has been developed. The SVC500 combines the capabilities of a high-speed film camera, the convenience of a solid-state digital video camcorder, and the computing power of a ‘486 PC to provide a complete, standalone platform for high-speed image acquisition and analysis. This paper will describe the design, features, and use of the SVCSOO andcompare these with the analogous aspects of film cameras."

Jan 1, 1994

By E. A. Lowe, A. F. Bellamy, J. W. Smith

"In the autumn of 1977 Bethlehem management initiated feasibility studies on recovery of by-product molybdenum from concentrate produced at the existing Highland Valley mining operation. Over the fall and winter months test work was carried forward concurrent with design, flowsheet, equipment specification and cost studies. The decision was made to go ahead with a 200 ton-per-day treatment plant. Construction started in early 1978 and progressed to an initial start-up stage in mid-June. Full operational status was reached in August 1978. Operational results through August 1979 are presented. INTRODUCTIONBethlehem Copper Corporation operates a 20,000 ton-per-day Open Pit Mine and Flotation Plant located in the Highland Valley, some 30 air miles Southwest of Kamloops and 20 miles Southeast of Ashcroft, B.C.Two open pits are worked; the Iona Pit with limited reserves of higher Mo content, and the lower grade, more extensive Jersey Pit. Upwards of 150 tons per day of bornite-chalcopyrite bulk concentrate is produced, ranging 0.25% to 1.5% in molybdenum grade depending on the area mined."

Jan 1, 1980

By D. Pappas

Over the past decade the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry?s injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked, injury rate, and days lost. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992?2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent.

Jan 1, 2011