Search Documents

By Paul S. Fisk, Arne Fareth, Julie Frietas, Francis Lo, Fidel L. Mallonga

INTRODUCTION This report describes the inspection of parts of the New Croton Aqueduct (NCA)undertaken for the New York City Department of Environmental Protection (NYCDEP)by Parsons Brinckerhoff Quade & Douglas, Inc., (PB) in association with Montgomery Watson Engineers of New York, P.C. (MWH). Support for the inspection was provided by AFC Enterprises, Inc., under Construction Contract CRO-333, “WM-11 New Croton Aqueduct Rehabilitation and Inspection Program.” The scope of the inspection work under CRO-333 included assessing the condition of the 10.3 km (6.4 mile) long, pressurized section of NCA and inspection of shafts, head houses and blow-off structures in both the pressurized and gravity sections. The CRO-333 inspection continued investigation work begun under ContractCRO-196, which ran from 1993 to 1997. The CRO-333 inspections were conducted from November 2004 to September 2005. Background The New Croton Aqueduct was put into service in 1891 to deliver water from the Croton River Watershed in Westchester County to consumers in New York City. Figure 1 shows the location plan of Croton Water Supply System. The design flow into Jerome Park Reservoir was 12.7 m3/s (290 mgd) and into the135th Street Gate House, further south, was 10.9 m3/s (250 mgd). The NCA has been operated as a gravity conduit from Croton Lake to Gate House No. 1, just north of Jerome Park Reservoir, since its original construction. The length from Gate House No. 1to 135th Street, which includes a major siphon under the Harlem River, has been operated under pressure. Croton Lake gate house, the north end of the alignment lies at Station 4+75; Shaft 33, the south end of the alignment lies at Station 1628+05. The diameter of the tunnel is 3.2 m (10.5 ft) in the siphon and 3.7 m (12.3 ft) in the Bronx and Manhattan sections. The pressurized sections, constructed in rock, consist of a brick lining surrounded by a mortared and grouted rubble backing. Figure 2depicts a typical tunnel cross section. The objective of the shaft and tunnel inspections was to locate and document defects, such as leaks, deterioration of lining material, cracks, spalls, delaminations,

Jan 1, 2007

By Alun J. Davies

This paper describes a design-build project for the construction of a tanker wharf for 150,000 dwt vessels. The tankers deliver oil from offshore oil fields to a Transshipment terminal on the south coast of Newfoundland. The project described is an expansion to a previously constructed facility, adding an additional berth. The first berth was designed conventionally as concrete structures supported on groups of independent, single piles. The second berth was awarded to Peter Kiewit Sons' Co. Ltd. based on an alternate design which utilized a "jacket" concept whereby prefabricated steel frames are placed on the seabed and serve as permanent templates and also give lateral support to the piles, thereby increasing their load capacity. This led to economies and time savings. Discussed herein is the design process and the field installation, covering the jackets, driven pipe piles, and the rock anchors.

Jan 1, 2000

By L C. Pretorius

Pipe pigging is a technique for the in situ (field) coating application, to create a seamless internal anti-corrosive lining of long pipelines. The technology originated in the cleaning of pipes, and these proven cleaning methods continue to be used today. Firstly mechanical cleaning of the pipeline is performed, using wire brush, razor back, course stud and fine wire pigs, then foam pigs, or criss cross pigs, and urethane blade scrapers to remove loose debris, wax, residual hydrocarbons and corrosion products from the pipeline. Part of the proprietary techniques and expertise is to ensure that these cleaning pigs do not get stuck Next chemical cleaning of the pipeline is performed, using repeated pig runs with detergents, solvents, acid etching, corrosion inhibitors, consecutively batched between two pigs, to ensure a clean, dry metal finish to a visual cleanliness standard of ISO SA2½. These in situ techniques were developed, 40 years ago to apply internal corrosion protection to pipes using a thin layer of epoxy based paint (50 to 100 micron). Until recently these old techniques were never improved upon. Although many thousands of kilometres of pipes were successfully coated with these thin film epoxy based paints and old application techniques, these thin paint films had problems in weld coverage, and were also unable to fill pits caused by pitting corrosion, and unable to replace metal loss caused by channel erosion. New coating material developments, revised application methods and modified pigging equipment have now made it possible to apply thick film coatings as corrosion barriers to the internals of pipes in the field, using these pigging techniques. The thick coating films can be up to 1 mm (40 mils) thick in a single coating run over long distances. The new thick film coating materials and application techniques are similar to continuous screeding, creating a far more robust seamless internal pipe lining when compared to the old technology of thin film paints. With thick film polymers the option now exists to create a structural GRP pipe within a pipe, be it steel or cementicious. It has been preferable, even necessary, to move away from the traditional epoxy paints and coatings. It was found difficult or impossible to use epoxy materials for these pipe coating applications due to the requirement for achieving a suitable viscosity with adequate hold up. In order to reduce epoxy viscosity a solvent or reactive diluent is required. This inevitably lead to solvent entrapment and poor cure characteristics in cold climates. Further mud cracking in over thick areas, the inability to extend or reduce pot life, poor control of cure time and limited resistance to aggressive or chemical environments made solvent based epoxy resins a poor choice.

Jan 1, 2006

By D. A. Bruce

Small diameter cast-in-place bored piles (pinpiles) have been installed throughout the world since 1952, but only more recently in the United States. The special features of their construction and performance makes them ideally suited for structural underpinning applications in difficult ambient and geological conditions. This paper describes the underpinning of part of a major industrial facility near Mobile, Alabama. In addition to being a most interesting and successful case history, per se, the paper also describes in detail a fundamental test pile program which has afforded a unique insight into the basics of load transfer mechanisms.

Jan 1, 1992

At Copper Refineries Pty. Ltd., Townsville, two reverberatory furnaces of 420 tonnes capacity are used to melt 210000 tonnes/year of copper for subsequent anode casting. When the refinery commenced production in1959, these furnaces were of 300 tonnes capacity. The original furnaces featured a silica brick hearth, magnesite and chrome magnesite side 'walls, and a sprung silica brick roof, but were unsatisfactory because of thelow refractory life and high costs. With continuous expansion in production and the incentive to increase furnace life and capacity the design of these furnaces has changed greatly since that time.The present furnaces feature all basic brick, a flat suspended basic brick roof, very extensive use of watercooled copper sections, and are of substantially increased (420 tonnes) capacity. Particular attention has been concentrated on high wear areas such as the taphole, side walls, and charging door jambs. Each furnace in its 24 h cycle, is charged, the copper melted, impurities skimmed off, metal "poled" prior to casting, and cast.The service condition during each of these operations is important in considering furnace refractory life.The improvements in operating practices and furnace 'construction which enabled the capacity of the furnaces to be increased are discussed. The life between major repairs to side walls has increased from 90 charges to300 charges.The scope for future improvement is considered and areas for development are suggested.

Jan 1, 1977

By David R. Beadman

The Fleming method is widely used for the analysis and prediction of single pile behaviour under maintained loading. The method does not distinguish between bored and driven piles. Driven piling avoids the need to dispose of spoil from the pile installation and is therefore becoming increasingly attractive. This paper considers the theoretical effects of the possible preload at the base of a driven pile after installation, using the hyperbolic functions as defined by Fleming. The Fleming method is reviewed and the equations and analyses are adapted, using spreadsheets, to allow for a possible preload. The simplifying assumption of the effect of the elastic compression of the pile is also reviewed and a more analytical method adopted to assess the elastic compression. Some driven pile test data is analysed to consider the possible effects of the preload on the performance of a driven pile and to test the theoretical relationships that are developed in the paper.

Jan 1, 2006

By D. Bois, P. Keating, J. Lemieux, M. A. Vallée, M. Allard, R. S. Smith, L. Z. Cheng, M. Chouteau, K. Fountain

"A comparison of data from INPUT, GEOTEM, and MEGATEM airborne electromagnetic (AEM) systems over the Aldermac deposit, Québec, Canada, was undertaken to evaluate the relative ef¬ficiency of these systems for the detection of small, deep conductors. The Aldermac orebody was mined between 1933 and 1934 to a depth of 200 m. A deeper mineralized zone was discovered in 1987. The MEGATEMII system was used to acquire 90- and 30-Hz data over the deposit in 2003 as part of a research project. These MEGATEMII data were compared with data acquired by other AEM systems (GEOTEM and INPUT), and the results show that the MEGATEMII response is ten times larger than the other sys¬tems. For the dB/dt response, 30 Hz gives a better signal-to-noise ratio, whereas 90 Hz has a better signal-to-noise ratio on the B-field.The data were evaluated by numerical modeling. The deposit was best represented by a complex mod¬el, comprising two weakly conductive bodies to approximate the alteration halo, two deeper prisms repre¬senting known orebodies, and three bodies ranging in thickness from 3 to 6 m and in resistivity from 12 to 20 ohm·m, representing the chargeable overburden. This implies that the MEGATEMII system is able to see a small conductive body at more than 200 m depth in an area where the response is contaminated by conductive overburden."

Jan 1, 2009

By Z. T. Bieniawski, José Miguel Galera, Benjamín Celada

TBM case histories from over 400 tunnel sections are analyzed presenting a comprehensive application of the Rock Mass Excavability (RME) index (Bieniawski et al.2006). The paper introduces two new adjustment factors, called the Factor of Tunnel Length and the Factor of Crew Effectiveness, which were established to represent more realistically the interaction of the rock mass characteristics, the TBM parameters and the performance of the crew operating the machine. A new correlation is provided for predicting the average rate of advance of double-shield TBMs working specifically in the double-shield mode.

Jan 1, 2007

By E. R. Wang

This paper outlines the engineering properties of shallow soil in Shanghai area. The main points that should be paid attention to during deep foundation investigation, and general conditions of experimental soil engineering are discribed.

Jan 1, 2010

By W. C. Lacy

Stratabound copper ore bodies in thick Proterozoic metamorphosed sedimentary and volcanic rocks at the Tong Kuang Yu Mine in southern Shanxi Province of China were considered as possibly being amenable to block cave mining. Initial evaluation of caving characteristics was based upon old calyx drilling records, limited underground mining experience and geological mapping, a few diamond drill holes and measurements in surface subsidence features. Classification and mapping distribution of rock quality types aided in mine design, prediction of fragment sizing and explosive requirements, cave assist and ground support requirements. Comparison is made between early feasibility predictions and actual mine experience.

Jan 1, 1989

By E. F. Schnitzer, D. R. Haight, G. T. Krogman

The 1997 New Year’s Day Rogue River flood near Medford, Oregon, USA, entered historic channels, eroded a 150-foot-wide buffer, and captured an inactive gravel pond located within the channel migration zone. Channel redirection caused by pit captures threatened adjacent inactive gravel ponds. In response to this capture, a stakeholders group of concerned individuals and organizations was formed. This group ultimately developed a rehabilitation plan, which conformed to the Rogue River’s geomorphic trends. A two-dimensional model, FLO-2D, was used to evaluate channel splits, flood storage, backwater, and future conditions. Modeling results coupled with trend analysis were used to create a stable design where stream barbs, gravel redistribution, a channel outfall spillway, bendway weirs, bank reshaping, and revegetation were integrated into a single plan for a three-mile reach. The quick action by the stakeholders group averted further damage to the Rogue River system and surrounding environment. The project has preserved three miles of mainstem habitat, one mile of side channel habitat, and protected ten gravel ponds from pit capture.

Jan 1, 2006

By J. Kempken, R. Degel, J. Kunze, R. König

The FeNi technology is currently dominated by high-power submerged arc furnaces, often designed as smelter as "two-inline-solution". To achieve the intended high efficiency, state-of-the-art design in good correlation with ores and reductants and an integrated layout of the whole plant is of great importance. An introduction will be given to general aspects in the production FeNi, plus a detailed overview of design principles for large FeNi smelters and finally some examples of innovations and research projects concerning Fe-Ni.

Jan 1, 2007

By Kouichi Tomisawa

Two bridges were constructed for extension work of Central Hokkaido Connection Road in 2005 at two different sites. Pile group foundations were employed for the foundations of abutments of the two bridges. In order to assess the performance of the constructed piles in the sites and to obtain design parameters for design in future, static alternating cyclic horizontal load test was carried out on one of the open-ended steel pipe piles constructed at each site. The ground at one site was characterised as a thick deposit of volcanic soils, and the ground at the other site was characterised as a very soft peat layer near the surface. In this paper the results of static alternating cyclic horizontal load tests on the piles at the two sites are presented and discussed in detail.

Jan 1, 2006

By T. Strong

"Selectively recovering pentlandite from high levels of pyrrhotite presents a technical and operational challenge. The liberation characteristics and also the chemical environment is critical to performing a successful separation. Reviewing the mineralogy to understand the characteristics of the ore and the plant flotation behavior is fundamental to designing a successful improvement program.At Savannah Nickel the challenges presented by a falling nickel price required a rethink of the flowsheet to improve the project economics through improving the concentrate grade and recoveries. Glencore Technology reviewed the plant performance and proposed and tested solutions to improve the grade performance of the concentrator with the support of the plant team. A pilot plant comprising a M20 IsamillTM followed by an L500/1 Jameson Cell was operated on various plant streams. In addition to the pilot plant, flotation surveys and a plant based laboratory program was used to supplement the plant understanding and within two weeks significant improvements were identified and demonstrated. The combination of the pilot operation and the plant based laboratory program was able to quickly demonstrate the improvements and test with equipment that is fully scaleable from pilot plant to full scale.IntroductionPanoramic Resources Limited is a Western Australian mining company formed in 2001 for the purpose of developing the Savannah Nickel Project in the East Kimberley region of Western Australia. Panoramic successfully commissioned the $65 million Savannah Project in late 2004. The process plant at Savannah comprises a single stage crusher, SAG mill, flotation, thickening and filtering stages to produce a bulk nickel, copper, cobalt concentrate. Metallurgical recoveries average 86-89% for nickel, 94-97% for copper and 89-92% for cobalt. The plant was originally designed for a throughput of 750,000 tonnes per annum, but has consistently outperformed the design specifications.Due to low nickel prices the Savannah Nickel mine and processing plant were placed into care and maintenance in May 2016. Prior to suspending production Glencore Technology was engaged to investigate options to improve the concentrate grade. With the discovery of Savannah North in 2014 and the Savannah North Scoping Study demonstrating LoM ~8 years and Mining Inventory of 6.07Mt @ 1.26% Ni, 0.64% Cu and 0.09% Co significant future potential exists. By completing pilot plant studies prior to shutting down, the plant engineering studies can be completed and the plant readied for restart by the time the nickel price improves."

Jan 1, 2017

By I. Gombköto, G. Földing, G. Mucsi, B. Csoke, J. Faitli, B. Kovács

This paper summarizes the main achievements of our previous project entitled "Development of a technological system producing quality guaranteed fly-ash based binder". Furthermore, this study deals with the laboratory experience of lignite fly ash utilization for two different goals. On the one hand the fly ash was tested as a binder; on the other hand it was investigated as an underground mine backfill material. Considering the first goal, the utilization of a mixture of mechanically activated fly ash and lime for producing an independent binding composition has been assessed involving determination of relationship between the degree of activation of fly ash and the strength of the obtained concrete. The results confirmed that this hydraulic binder is suitable for construction of stabilization and capping layers or base layer. Regarding the backfilling application, this paper presents laboratory experiments, their results including settling tests, hydraulic permeability and strength measurements and dense slurry technology related results.

Jan 1, 2011

By Paul Eger

The use of wetlands to treat mine drainage has become increasingly common, particularly as more information is available on their operation and construction. However, the lifetime of each system is still, at best, an estimate. Treatment lifetime depends on the types of processes that provide the majority of the metal removal. Anaerobic systems (vertical flow systems) rely primarily on sulfate reducing bacteria, which reduce sulfate to sulfide and generate alkalinity. Metals can be precipitated as sulfides, and acidity is neutralized. These systems can remove over 90% of the metals and increase pH from around 4 to over 7. The bacteria will remain active as long as the system remains anaerobic and contains an adequate supply of sulfate and small chain organics. Although estimates of lifetime made on the total carbon in the system suggest that lifetime should exceed 20 years, data from field and laboratory studies show that the rate of sulfate reaction decreases with time, and that after several years rates decreased substantially. To maintain acceptable treatment, either additional organic material must be added or the total metal and acid load to the system would need to be reduced substantially. Aerobic systems (overland flow wetlands) can effectively remove metals from neutral mine drainage by reactions with organic material in the substrate. Over 90% of the copper and nickel have been removed in aerobic systems treating mine drainage in Minnesota. The primary removal processes in these systems include adsorption, ion exchange and complexation, which are finite; removal will cease unless new removal sites are generated. Two wetlands built in Minnesota have been successfully treating mine drainage for 12 years. At one of the wetlands, the annual production of new removal sites has been estimated to be equal to the annual metal input, and, as a result, metal removal should theoretically continue indefinitely.

Jan 1, 2005

By Peter Jackson

The dewatering of the large construction pits required for major infrastructure projects often has a significant impact on the environment. This is particularly so in urban areas and where groundwater resources are of interest. These environmental impacts are inter alia, groundwater lowering and the consequent effects such as settlement and deterioration of timber foundations, together with the impact of the dewatering on the groundwater quality. In order to minimise the environmental impact of the dewatering, the quantity of water to be abstracted and the amount of groundwater lowering in the surrounding area must be minimised. This paper describes the measures that have been taken on the Copenhagen metro project to achieve the objective of minimal environmental impact whilst still carrying out a major dewatering scheme.

Jan 1, 2000

By K Nilsson, D Connelly

Troy Resources acquired the Karouni Gold Project in Guyana, South America in 2014 and immediately proceeded to a Pre-Feasibility Study and project implementation. The study considered two open pit mines feeding a conventional carbon in leach (CIL) gold plant with a capacity of 1Mtpa. The study assumed a total of 2.61 million tonnes of ore with an average grade of 3.84 g/t gold with a recovered gold production of 303,526 ounces over a three year mine life.The project development involved drilling metallurgical test holes, securing second-hand major pieces of equipment where suitable, and arranging shipping to Guyana. The remote location meant logistical considerations were paramount. The plant consists of conventional two-stage crushing with single stage ball milling and a gravity circuit. The tailings circuit includes DETOX.The extremely high rainfall presented challenges with water management and the necessity to dispose of clean water to the environment. The DETOX was also mandatory due to the highly sensitive environment and past history in the area. The criticality of this meant that in the design, any cyanide in the tailings would precipitate in a plant shutdown.Lessons were learned and the project has been both profitable and successful for Troy Resources in a new operating location. In addition, the project has created jobs, delivered royalties and brought new skills into an area where previously there was little current mining activity.CITATION:Nilsson, K and Connelly, D, 2015. Karouni Gold Project from drill core to commissioning, in Proceedings MetPlant 2015, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Gabriel S. Esterhuizen, Anthony T. Iannacchione

The roof rock in underground limestone mines in Northern Appalachia can be subject to high horizontal stresses in spite of the shallow depth of the workings. The high stresses can cause roof stability problems. The National Institute for Occupational Safety and Health staff have observed a distinctive asymmetrical mode of failure at the pillar-roof contact in two underground stone mines, which is different from the typical failure mode observed in response to excessive levels of horizontal stress. A dip of greater than 5° was identified as a possible cause of this mode of failure. Numerical model experiments showed that an increase in the dip of the workings can cause an increase in the stress at the up-dip corner of the roof beam. A case study is presented in which failure at the pillar-roof contact was observed where the dip of the workings was 7° in a high horizontal stress field. Numerical modeling showed that the relatively small dip of the workings could have induced stresses changes in the immediate roof that would explain the failures. The model results also showed that this mode of failure is less likely to occur if the limestone pillars contain weak bedding planes that provide stress relief. In addition, the results showed that for the conditions at the case study site, the stress in the roof beam was not sensitive to the thickness of the roof beam or to the excavation span. The high horizontal stresses at this site are an important contributing factor to the observed failures.

By A Maldonado, A Robert, K G. Mercer

The Hamersley Group in the Pilbara, Western Australia, consist of interlayered banded iron formation (BIF) and shale host rock formations within which a large number of open pit iron ore mines have been established. The slope stability of most of the mining excavations developed within these formations is controlled by the relatively low shear strength of the shale groups and shale bands, which are the weakest rock types. Shale formations range from fresh to highly weathered and are generally highly fissile when fresh, and clayey when weathered. An accurate understanding of the shear strength of these materials across the entire weathering continuum is therefore a key importance for assessing the slope stability of these mines.Historically defect laboratory testing results for the Pilbara mines have been analysed mechanically using direct shear testing (DST) to measure a number of geotechnical characteristics of the rock bedding and defects. This paper sets out the current practice in the industry in terms of the laboratory testing and presents a possible application of hyperspectral data to empirically correlate the shear strength of shale bedding with the relative mineralogy abundance on the bedding surface. This was achieved by creating both hyperspectral and geotechnical data sets for the same samples.In the study the shale samples were separated into three distinct assemblages: iron oxide + kaolinite, iron oxide + white mica + kaolinite, white mica + kaolinite, which had 40, nine and two samples respectively. Analysing these assemblages alongside DST data showed that samples with white mica had reduced non-variable shear strength, whereas samples with iron oxide + kaolinite had an overall higher shear strength but with a greater variance. It is inferred that the reduced shear strength in the white mica samples is due to the sheet (or plate) like structure of the mineral, giving it a weak stress plane. Confidence in the trends observed can be reinforced by expanding the data set in future works. The investigation also includes a discussion on weathering grade and addresses the question as to whether mineralogy abundances influence these characteristics in Hamersley shales.CITATION:Maldonado, A, Mercer, K G and Robert, A, 2017. The relationship between mineralogy and shear strength of Pilbara Hamersley Group shales across the weathering spectrum, in Proceedings Iron Ore 2017, pp 423–430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017