Search Documents

By M. Cross

Heap leaching presents a complex physico-chemical process to model and a significant challenge to develop a comprehensive model enabling reliable predictions of heap behavior over the long term. A computational modeling framework is described for the analysis of multi-phase flows in reactive porous media suitable for tracking metals recovery, for example, in heap leaching and environmental recovery processes. This modeling framework employs appropriately formulated, parameterized, and solution procedures to capture: 1) liquid and gas flow through heterogeneous porous media subject to variably saturated flow conditions, 2) the complex and dynamically changing nature of the porous media structure, 3) the transport of reactants and products of reaction, 4) the simultaneous mass and heat transfer, and 5) the role of bacteria as a catalyst for reactions. A second class of challenges to accurately model heap processes is to identify and then capture all the process data to characterize the reactivity of particular ores, the mine planning for the construction of the heap, leach schedules, meteorological data, etc. The objective of this paper is to outline these challenges and to describe a modeling framework that can cope with arbitrarily complex geometries and provide tools for rapid and accurate process assessment.

Jan 1, 2006

By C. Lupi

Zinc impure solutions as spent electrolytes, leach liquors coming from aqueous treatment of both minerals and solid waste, need to be purified before undergoing the treatment to obtain the final product. Solvent extraction is one of the most selective operations particularly when many metallic ions are present in solution. Zinc pure solutions are frequently obtained using DZEHPA as extractant. In this work an investigation on zinc extraction effectiveness of naftenic acid was carried out. After determining the best diluent and the optimal extractant concentration, the partition coefficient was determined as a function of temperature, equilibrium pH and zinc concentration. Finally same batch tests to determine the equilibrium curves at room temperature on exhausted electrolyte coming from zinc cell were carried out by using naftenic acid, D2EHPA and TBP. The pH giving, for each extractant, the best extraction yield was selected in order to compare the equilibrium curves. Experimental results show that all the examined extractants are very effective in zinc extraction if the process conditions are appropriately selected. In order to avoid an impure solution pre- treatment and to obtain the maximum ertraction yield the appropriate solvent can be chosen.

Jan 1, 1998

By C. L. Kusik

Environmental issues are having a significant impact on how automobiles are designed and ultimately disposed of at the end of their lives. On one hand, increasing concerns about landfill disposal have resulted in greater attention being focused on recycling materials and components from old junk autos. On the other hand, corporate average fuel economy (CAFE) requirements have led to downsizing, use of coatings, materials substitution and other measures that often make recycling more difficult. Automobile makers have responded to Corporate Average Fuel Economy (CAFE) Standards in a variety of ways such as: Downsizing; Designing of more fuel efficient engines; Reducing aerodynamic drag by sleeker body designs; Redesigning by using thinner gauges of coated steels; and Substituting material such as lightweight plastic or aluminum parts for steel. Other driving forces affecting production techniques, choice of materials and recycling issues include the Clean Air Act and its amendments, RCRA. and other environmental legislation. The variety of materials used in automobiles makes the recycling issue extremely complex. Not only does one have different materials used in different automobiles for making similar parts, but changing designs, evolving environmental issues, landfill closures affecting solid waste disposal, and increasing raw material quality standards have created a complex set of dependencies related to materials use and recycling.

Jan 1, 1994

By Xiao Long, Ting Wu, Lilong Zhu, Qian Wang, Shengping He

"During the continuous casting of peritectic steel slabs, mould fluxes with high crystallization capacity are usually chosen for improving slab surface quality. However, the lubrication condition of casting shell also could be deteriorated. Since precipitation of crystals within liquid slag film can change the composition and property of liquid slag over solid-liquid slag film interface region, its impacts on continuous casting process also are not clear. In order to clear this phenomenon, an experiment method was put forward, and mould fluxes for peritectic steel slabs continuous casting were selected and examined. The results reveal that after crystals have been separated, the crystallization capacity of leftover liquid slag increased with different levels, which could deteriorate the lubrication condition of casting shell and cause a series of problems. Thereby, mould fluxes with high crystallization capacity at beginning for heat transfer control and then weaker after crystallization should be considered in the future.IntroductionIn the continuous casting of peritectic steel slabs, contradiction between heat transfer control and slab shell lubrication by mould fluxes has been treated as a key problem for maintaining a smooth manufacturing process [ 1]. Strong and uneven horizontal heat flux over the meniscus region will cause uneven solidification of casting shell, especially for peritectic steel slab with enormous volume change caused by phase transition. All of those could cause surface defects like longitudinal crack [2-4]."

Jan 1, 2013

By Roderick I. L. Guthrie, Donghui Li, Mihaiela Isac, Luis Calzado

The HSBC is an ideal process for the production of BMG strips. The purpose of the present work was to investigate the casting of Ca-based, bulk amorphous strips. The possibility of casting three Ca-based alloys (60Ca-20Mg-20Al, 60Ca-15Mg-10Al-15Zn and 55Ca-15Mg-10Al-15Zn- 5Cu (at.%).) was investigated, using the HSBC simulator. Numerical simulation and mathematical modeling were used to predict temperature variations and cooling rates, under different interfacial gaseous atmospheres (helium and air) near the meniscus region. Given the critical cooling rates and glass temperatures needed to be reached for the vitrification of the respective alloys, this leads to predictions of the critical thicknesses possible with this novel casting process. To validate our predictions, these alloys were then prepared and cast onto the sand-blasted, solid copper substrate mould of the HSBC simulator. The possibility of producing Ca-based metallic glassy strips via the HSBC processes was confirmed, using optical microscopy, X-ray diffraction and Scanning Electron Microscopy, to characterize the glassy properties of the cast strips. It was found that the HSBC process would be able to provide sufficient cooling to form amorphous strips for the 60CA-15Mg-10Al-15Zn and 55Ca-15Mg- 10Al-15Zn-5Cu alloys, but not the 60Ca-20Mg-20Al alloy.

Jan 1, 2014

By Halvor Dalaker, Alain Marc Ferber, Thor Anders Aarhaug, Pål Tetlie

Off-gas monitoring of experimental reactors give little information about intermediate reaction products and reflect chemical equilibria at reduced gas temperatures. A reactor design with optical access was designed and tested in order to be able to qualify and quantify gaseous species from their emission spectra. By use of a sequence of sapphire, UV fused silica and IR transparent sapphire and CaF2 windows and lenses optical access to a hot, maximum 1800 °C, reaction zone was gained. A cooled area behind the reaction zone was used as a background in order to avoid signal saturation from reactor walls. In addition to molecular emission spectra, atomic emission lines are used to characterize stable gas constituents and radicals. The setup has been designed for the study of methane dehydrogenation experiments in order to investigate the carbon activity of reduction of oxide with methane, but has also been used to monitor gaseous silicon suboxide.

Jan 1, 2015

By Norihisa Iida, Yutaka Koshiba, Tsutoipu Masui

"Mitsubishi Materials has many years of experience in the production of oxygen free copper (OFC) and its alloys with a fully continuous-casting process. Four grades of OFC, commercial, electronic, superconductor, and ASTM class I are available according to user needs such as stabilizer for superconductivity, magnetron, and ultra-vacuum systems. Along with Cu-Ag and CuSn, we offer OFC based copper alloys such ·as Cu-Cr-Zr, Cu-Fe-P, Cu-Ni-Si and others, that are suitable for lead frame and connectors. Within the maximum sizes of 260mm X 1050mm for cakes and 385mm diameter for billets, we are very flexible and can adjust the ingot size to customer’s requirements. Other products that we can supply are semi-finished products such as hot rolled sheet, ·forged blank, extruded rod and finished products like mold for continuous casting of steel, ring mold for non-ferrous casting and backing plate for sputtering target.IntroductionMitsubishi Materials Corporation developed mass produced high quality oxygen free copper and. high copper alloy ingots in the 1960's. We produce 60,000 - 70,000 tons annually giving us 22 - 23% share of the world's market.Our oxygen free copper and. copper alloys are produced with a fully continuous casting process using only high-grade copper cathodes from our Naoshima and Onahama refineries. The raw material is melted and cast in' a carefully controlled atmosphere resulting in a product with low impurities and excellent properties.Using a controlled atmosphere it is possible to produce high quality copper alloys including active elements like chromium (Cr), zirconium (Zr), titanium (Ti), and magnesium (Mg) which are difficult to produce using standard batch casting methods.Using our own cakes and ·billets we produce and supply worldwide wrought materials like molds for ferrous and non-femous casting. These products receive special patented thermo-mechanical· treatments resulting in high strength and excellent conductivity with low cost."

Jan 1, 2000

By James A. Sommers

Hydrolysis of NbC15 is used to recover oxide values for ceramic and metals production. Reaction of NbC15 with water is rapid, exothermic and vigorous, yielding a gelatinous slurry. In contrast, dissolution of NbC15 in 12 N HCl is endothermic, resulting in a clear yellow solution. Such solutions can be de-hydrochlorinated by controlled contact with air, to precipitate a tantalum¬rich solids, depleting the liquid of its tantalum content. In this way, cheap, useful Nb-Ta partial separation is achieved. The separation is based upon differential oxide-chloride stability. Nb2O5 with <200 ppm Ta/Nb has obtained from starting levels of 2000 ppm. Observations are made on the different types of hydrolysis.

Jan 1, 1992

By Sylvain Gouttebroze, Mohammed M'Hamdi

In a previous work, a small scale Bridgman furnace has been used to study silicon bi-grain crystallization at different cooling rate. This work expands the analysis by studying the mechanical interaction between the crucible and ingot during the solidification and cooling. The thermal model is based on a 2D-axisymetric heat-transfer model. The flux histories are then transferred to the ingot-crucible 3D-model. Anisotropic Elastic and Crystal Plasticity model are used to model the silicon deformation. Four different assumptions are applied to model the mechanical contact crucible-ingot and three grain misorientations are considered. The results show the strong impact of the alumina crucible contraction on the stresses and deformations in the silicon ingot.

Jan 1, 2015

By Lifeng Zhang, Zineb Benouahmane, Yaqiong Li

Experimental oxidation tests at high temperature (1000-1200 °C) on SiC samples have been respectively performed under wet and dry air atmosphere for different holding times. The thickness of thermally grown oxide was experimentally measured by DEKTAK Stylus Profilometry. The results showed that the oxidation rate was increased with temperature and holding time, corresponding to a passive oxidation regime which led to the formation of SiO2 layer. The sessile drop method was employed in order to measure the contact angles between Si and SiC at high temperature. Contact angle can be varied from 39.6° to 75.6° by controlling the atmosphere. The deoxidation of the oxide layer and infiltration of liquid silicon caused a decrease in the contact angle.

Jan 1, 2016

By Beatriz Amarai Campos, Jorge Alberto Soares Tenorio1, Denise Crocce Romano Espinosa, Adriana Johanny Murcia Santanilla

"The aim of the present work is to investigate the recovery of nickel from obsolete cell phones printed circuit boards. The printed circuit boards were firstly submitted to a grinding process and then leached in sulfuric acid. Nickel was extracted from aqueous solution using Cyanex 272. Aqueous/organic ratio was 1/1. The effect of both pH and modifier addition on selectivity of extraction was investigated.IntroductionCurrently, electric and electronic equipments (EEE) have become a necessity to the modern life. Associated with this necessity comes the continuous and increasing replacement of those equipments by new ones. The accelerated technology advances are responsible for the generation of electric and electronic waste. This waste can be dangerous not only to human health but also to the environment. Waste of electric and electronic equipments (WEEE) has a variety of components and metals in its composition becoming a potential pollutant to the environment when not properly discarded. Its wrong disposal causes a loss of materials that could be recovered and reused. Therefore WEEE treatment is an important matter because it can assist the reduction of waste generated and the recovery of valuable metals.Printed circuit board (PCBs) is an essential component of EEE and is typically very complex from a chemical point of view. Several metals may be present in its composition, such as cooper, nickel, iron, zinc, lead, tin and silver1''. This characteristic hinders the development of a simple treatment, making it necessary the application of chemical and mechanical processing for their recycling'4'. The UN estimates that approximately 20 to 50 million of tonnes of WEEE are generated worldwide each year."

Jan 1, 2011

By Enrico Cerilli, Bryan Salt

Xstrata Nickel’s Sudbury Smelter has systematically developed its converting aisle from a single stage to a counter current multi stage converting process. This has required the development of two unique converters; the Slag Cleaning Vessel (SCV) and the Slag Make Converter (SMC). This has resulted in a unique three stage converting process that enables treatment of secondary materials and producing a slag that can be discharged without further treatment. The paper will also discuss future changes currently being considered to further improve environmental, plant hygiene and productivity performance.

Jan 1, 2009

By M. F. Chambers

Neodymium metal was electrowon from a molten-chloride electrolyte at 650° C using a molten-metal cathode. A 50 mol pct NdC13-50 mol pct KC1 mixture served as the electrolyte. Binary metal alloys of &apos;Mg with Zn and Mg with Cd were used as molten cathodes. Under the best conditions, current efficiencies were 90 pct with a Mg-Zn cathode and 80 pct with a Mg-Cd cathode. Vacuum distillation was performed at 1,100° C for 30 min under a vacuum of 10-3 to separate the cathode metals from the neodymium. Neodymium metal of 99.9+ pct purity was recovered from the Mg-Cd alloy cathode. Almost 2 pct zinc remained in the neodymium recovered from the Mg-Zn alloy.

Jan 1, 1989

By W. G. Davenport

Chapter 11 determined the combinations of industrial oxygen, oil and blast preheat that will steadily produce 65% Cu matte from pure chalcopyrite concentrate. It showed that the . combinations are described by a flat plane. It also showed that the minimum energy requirement for making 65% Cu matte occurs with maximum oxygen enrichment, zero oil and zero blast preheat. This chapter examines the, effect of matte grade on industrial oxygen, oil and preheat requirements.

Jan 1, 2001

By M. E. Reed

Clyde Materials Handling (CMH) and WorleyParsons have developed a concept for a flash furnace feed system using the specialist pneumatic conveying equipment expertise of CMH and the flash furnace process experience of WorleyParsons. CMH has developed a proprietary volumetric feeder (called a Rotofeed) which is extremely accurate and overcomes many of the problems inherent with loss-in-weight screw feeders and drag chain conveyors, previously regarded as state-of-the-art. Initial indications are that the Clyde-WorleyParsons Feed System could deliver the following benefits to Flash Furnace operation: ? Accurate pulse-less delivery of feed material to the head of the burner leading to improved combustion performance and process stability; ? Highly accurate split to the individual quadrants of a conventional burner tube, or provision of a smooth hollow curtain to a burner without guide vanes; ? Decreased pressure pulsation in the furnace due to improved combustion control and performance; ? Decreased temperature fluctuations in the furnace due to improved combustion characteristics and hence reductions in refractory thermal stress and wear; Plant measurements have indicated a correlation between the discharge of concentrate from the drag chain conveyor and high speed pressure fluctuations in the flash furnace settler. Pilot scale test have been conducted to illustrate that the system delivers pulse-less feed to the burner with even feed distribution axially.

Jan 1, 2006

By Alexander I. Raitchenko

"An electroconductive viscous liquid may flow in laminar or turbulent regime under Lorentz-force generated by the intercrossed electric current and magnetic field. When there is a starting flat layer between hard and free boundaries with surface tension the spatial Lorentz-force can create a specific stationary regime of flow: the plane free surface will transform into the wavy one, and the movement in the depth will be not laminar and not turbulent, but this regime will be characterized by organized forms with indications of ""rolling of long cylindrical drops"". Wave-length is determined by the viscosity, the density, the surface tension, the average thickness of layer, and Lorentz-force. ·The limit of wavy regime is determined by most long of wave which is directly proportional to the critical value of specific flow and inversely proportional to the kinetic viscosity. The proper critical value of Reynolds number is determined by the dimensionless combination containing surface tension, density, viscosity, and Lorentz-force. The mentioned dimensio.nless combination in our case is some criterion substituting the known Kapitsa number for case of the thin viscous liquid layers under gravity. Spreading of admixture by mechanism of wavy regime is more rapid than by common diffusion or by laminar flow. The suggested conception can be a contribution into the theoretical basis for elaboration of some specific liquid metals technologies."

Jan 1, 1999

Off-gas cleaning from metallurgical plants requires? in many cases very low dust contents which are difficult to achieve with conventional scrubbers, even with high energy input. Lur.gi has developed a scrubber which improves the separation of the fine dust by electrical charge prior to. the scrubbing zone. An Electrostatic Scrubber has been successfully installed for the off-gas cleaning from slag&apos; granulation after a waelzkiln achieving less than 1 mg/m3 in the clean gas.

Jan 1, 1992

By W. Petruk

The silver-rich cobalt-nickel arsenides ores of the Cobalt area in Ontario, Canada were mined for silver from about 1904 to 1985. The ores contained about 8 oz to 100 oz Aglt and about 1 wt% Ni and 2 wt% Co. They were processed by gravitational techniques, screening and flotation to produce separate silver and Fe-Co-Ni arsenide concentrates. The silver concentrate was smelted, and in some cases the arsenide concentrate was sold to custom smelters which recovered silver and other metals. The ores display a wide variety of textures and contain many minor and trace elements. This paper presents an evaluation of mineral characteristics that have a bearing on extractive metallurgy and smelting of this type of ore.

Jan 1, 1993

By A. Niedbalska

A technique was developed for low pressure diamond synthesis using a specially prepared glassy carbon. The glassy carbon is produced in the form of solid plates by slow carbonization process of phenol formaldehyde resin interrupted at temperatures of 1273° K, 1073° K, and 923° K. The diamond synthesis is performed using cobalt plates as a catalyst-solvent. Synthesis was carried out at applied pressures of 6.0 and 3.8 GPa and a temperature of 1970° K and 2170° K. The products were analyzed by the x-ray powder dyffraction method and by microprobe to identify the diamond crystallites. The samples were taken from the place of contact between the glassy carbon and the cobalt catalyst. They were separated from the charge by a chemical method. Diamonds of the best form and the largest size were obtained at pressures that were much lower than those used in the traditional graphite method of diamond synthesis.

Jan 1, 1989

By Kazuya Koyama

The leaching of copper from a printed circuit board (PCB) and the electrodeposition of copper from a cuprous solution in ammoniacal alkaline solutions were examined in order to develop an energy-saving hydrometallurgical process for copper recovery from electronic scrap. In the leaching experiments, copper in the PCB was oxidized by Cu(II), and Cu(I)-ammine complex ions were formed. The copper(I)-ammine complex slightly depressed the leaching rate, while Cu(II)?ammine markedly enhanced it. During the electrodeposition experiments, the current efficiency of copper deposition was approximately 100% in the current density range of 200 to 1000 Am-2. The electrodeposition of copper from the Cu(I)-ammine complex solution favored the production of plates rather than powders.

Jan 1, 2003