Search Documents

By D. S. Barr

The Freeport McMoRan chlorination circuit is comprised of four related processes: ore chlorination, gas scrubbing, chlorine supply and excess hypochlorite removal ("hypo kill"). Each of these processes are described, and related to the pertinent mineralogic components in the carbonaceous ore feed to the plant. The chlorination system in use at Jerritt Canyon to passivate forms of preg-robbing organic carbon has proven to be a cost effective and efficient means to recover gold from low sulfide carbonaceous refractory ores, where gold may not be specifically associated with either the sulfides or the carbon.

Jan 1, 1987

By Donna Post Guillen

"Cyclopentane, a flammable hydrocarbon, is being considered as a working fluid for waste heat recovery applications using Organic Rankine Cycles with Direct Evaporators. A postulated failure mode consisting of a pinhole leak in a heat exchanger tube raises safety concerns due to autoignition of the working fluid. Experiments were conducted to determine the ignition delay time (IDT) of cyclopentane using an Ignition Quality Test™ (IQT™) device. Two sets of experiments were conducted per ASTM D6890 (with exception to charge pressure and temperature) to determine ignition delay of the fuel at atmospheric pressure for standard air (-20.95% oxygen) and vitiated air (13.3% oxygen) at a temperature of 803 K. Operation of the IQT device at a much lower pressure (1 bar) than normal operation (21.4 bar) with a standard injector led to very rich conditions and wetting of the stainless steel chamber walls. Catalytic effects are postulated to produce the small IDTs observed. Experiments were repeated with a modified injector to prevent wall wetting, resulting in average IDTs that are substantially longer.IntroductionCyclopentane is being considered for use as a working fluid in a Direct Evaporator of an Organic Rankine Cycle (ORC). In this configuration, the heat exchanger is placed directly in the flow of the hot exhaust gas, rather than using a secondary heat transfer loop to isolate the flammable working fluid from the heat source. This configuration offers the advantages of approximately 15% lower cost and improved efficiency over a standard ORC. However, placing a heat exchanger operating with a flammable hydrocarbon in the hot exhaust gas stream presents potential safety risks. If a pinhole leak were to occur in the heat exchanger, working fluid could leak into the hot exhaust stream. Gas turbine exhaust is provided to the Direct Evaporator at a temperature of approximately 803 K, whereas the autoignition temperature of cyclopentane is 634 K (Gallant and Yaws, 1993). Autoignition of the working fluid has been identified as the key risk for this type of system.Autoignition occurs when sufficient self-heating by chemical reactions takes place to accelerate reaction rates to produce full-scale combustion. This is in contrast to forced ignition, in which an external source (e.g., spark) is employed to initiate the combustion process. For combustion to occur, the fuel to oxidizer concentration must be between the lower (lean) and upper (rich) flammable limits. The reaction rate depends on the species concentration of the fuel and oxidant, the local temperature and pressure. Ignition processes are comprised of steps that take a fmite amount of time. This latent period prior to the start of combustion is referred to as ignition delay time (IDT)."

Jan 1, 2012

By Ulrich E. Klotz, Gemot Pottlacher, Shahid Mehmood

"Platinum alloys are frequently used in technical applications and in jewellery. Their thermophysical properties such as density, heat capacity, thermal conductivity and surface tension play an important role in casting processes and are required as input data for casting simulation. Scope of this work was to investigate these properties by different methods. Platinum and four alloys namely, Pt96Cu4, Pt68Cu32, Pt50Cu50 and Pt25Cu75 were investigated. Melting range and thermal expansion was measured at fem by DSC and dilatometry, respectively.At TU Graz wire shaped samples were investigated by an ohmic pulse heating technique. This technique allows the calculation of specific heat capacity and the temperature dependencies of electrical resistivity, enthalpy, and density of these alloys in the solid and liquid phase. Experimental results were compared with available literature and data from thermodynamic calculation using the SNOBl database and ThermoCalc.IntroductionPlatinum is a precious element and its alloys are commonly used in jewellery. But Platinum is much more difficult to cast then other jewellery elements like silver or gold, because of its high melting temperature, large shrinkage during freezing, low thermal conductivity, high surface tension, and high viscosity. As a result there arise problems during casting. Hence to resolve these difficulties a detailed study of thermophysical properties of solid and liquid platinum and its alloys is necessary for simulation and casting. The Platinum alloy samples were prepared by vacuum induction melting and casting into copper molds. Rods of 3 mm in diameter and a length of 80 mm were prepared and drawn to wires of 0.5 mm in diameter."

Jan 1, 2011

By Ian Masters

Rotary furnaces are widely used throughout the metals industry. These furnaces vary in size and geometry, but are fundamentally the same from a thermodynamic viewpoint. A generic method is proposed that can be used to model all furnaces of this type, provided that the correct material and process parameters are known. Various approaches have been attempted in the past based on a continuum (FEA or CFD) approach. However, the complex fluidlsolid interactions present in a rotary vessel are not easily solved using these methods, which work best where the material boundaries are well defined. In this paper a lumped parameter model is proposed. Variations within a section of the model are ignored, but to ensure thermodynamic correctness, the heat transfer between sections is carefully considered. For example, it is reasonable to assume that the whole of the melt pool is at the same temperature, due to rotary mixing. This may then be modeled with a single set of parameters, and the detail is contained in obtaining the correct heat transfer mechanisms from the rest of the furnace.

Jan 1, 2002

By L. Yin, R. B. Haber, N. Sobh, D. A. Tortorelli, R. W. Hyland Jr.

"We optimize continuous quench process parameters to produce a desired precipitate distribution in aluminum alloy extrudates. To perform this task, an optimization problem is defined and solved using a standard nonlinear programming algorithm. Ingredients of this algorithm include a cost function, constraint functions and their sensitivities with respect to the process parameters. These functions are dependent on the temperature and precipitate size which are obtained by balancing energy to determine the temperature distribution and by using a reaction-rate theory to determine a discrete precipitate particle size distribution. Both the temperature and the precipitate models are solved via the finite element method. Since we use a discrete particle size model, there are as many as 105 degrees-of-freedom per finite element node. After we compute the temperature and precipitate size distributions, we must also compute their sensitivities. This seemingly intractable computational task is resolved by using an element-by-element discontinuous Galerkin finite element formulation and a direct differentiation sensitivity analysis which allows us to perform all of the computations on a PC.1 IntroductionThis work addresses the need for an integrated design capability that links microstructure evolution to the process parameters. It is motivated by the manufacture of lightweight aluminum-alloy extrusions for use in automotive structures. Aluminum alloys offer obvious benefits, however, care must be taken to manufacture favorable microstructures that ensure acceptable structural performance. For example, the manufacturing process for 6000-series components involves hot extrusion of cast aluminum billets followed by either an air or water quench process. The bill~t's initial grain structure is dramatically altered during extrusion by massive mechanical deformations and recrystallization processes. The microstructure continues to evolve during the quench, as complex chemical processes determine the formation of precipitates. The control of the precipit'ate size distribution is vital. Indeed, large precipitates located on grain boundaries serve as crack initiation sites which adversely effect structural crash· worthiness."

Jan 1, 2000

By Jian-Xun Fu, Hong-Qiang Liu, Si-Yu Liu

The production of zinc-bearing solid dust is up to 4%~8% of total crude steel in steel plant, which is difficult to be recycled in traditional methods. To fully utilize the resources and reduce environmental pollutions, Chinese steel plants are using rotary hearth furnace (RHF) process to recycle solid dust. A consequential life-cycle inventory was carried out to assess the impact of dust recovery on greenhouse gas emissions based on the local production status. In the study system, the selected steel plant named which have 10.5 million tons of Crude steel productivity and 0.48 million tons solid dust come out meanwhile. To research, a RHF production line of 0.3 million tons directly reduced iron (DRI) a year was established to recycle the solid dust. The DRI will be obtained from RHF and sent to the blast furnace as raw materials to reduce the demand for iron ore and coke in steelmaking processes. By researching on the life-cycle inventory in the system, the steelmaking process with RHF was 2299.3kgCO2/ton steel. It’s a little higher while compared with the process without RHF, which data is 2297.0 kgCO2/ton steel. The small production of DRI make a small difference to reduce the carbon footprint of steelmaking process, the added carbon footprint of RHF process is more than BF and other steelmaking processes reduced. It is concluded that dust recovery has no contribution to the greenhouse gas emission reductions in the technic condition of Chinese steel plants currently.

Jan 1, 2016

By Juergen Antrekowitsch, Stephan R. Steinacker

The main aim of the electric furnace treatment in the primary copper industry is the reduction of valuable metals such as zinc, lead or copper itself. On the one hand legal restrictions for the further use of the treated slag are constantly getting stricter while on the other every type of loss in the oxidic phase leads to economic disadvantages. In order to fully understand and to improve the process, kinetics during the reduction play an essential role. In the first part, this paper highlights the theoretical background of the reduction process, while the following chapters present experimental aspects and results from laboratory scale trials at the Montanuniversitaet Leoben. In addition, the comparison between the chemical reaction and the diffusion model plays a continuously important role. By investigating the reducibility of electric furnace slag, process adaptions and ameliorations are developed.

Jan 1, 2016

By Keith Rozenburg, Ivar Reimanis, Jesus Chapa

"Experiments in conjunction with finite element analysis (FEA) are used to better predict crack propagation in ductile/brittle graded composites. Cu/W graded composites were fabricated by stacking discrete layers of powders and hot pressing. Crack propagation was studied by loading a notched beam in four point bending and examining the subsequent crack deflection. The notch was placed within a particular composition of material, oriented in a direction perpendicular to the gradient direction. Elastic and plastic mismatch between different constituents in the graded composite induce shifts in the phase angle of loading, thereby causing the crack to deflect. FEA indicates that thermal residual stress has a negligible ""influence on the crack path. The combined FEA and experimental results suggest that elastic mismatch is the single most important material property-related factor in controlling crack deflection.IntroductionMany 'applications would benefit or may even require materials whose performance or functionality must vary spatially. While the concept of functionally graded materials has existed for nearly one hundred years, it is only within the last fifteen years, that research efforts have focused on generic issues in processing, properties and performance of functionally graded materials. This generic research effort has brought together scientists and engineers from traditionally different disciplines to address common issues with graded composites. The current work focuses on issues in structural joining. A wide variety of applications require some type of joining between dissimilar materials. Examples include thermal barrier coatings for turbine engines, wear resistant coatings for tools, ceramic engine parts, and microeiectronic devices, as well as many traditional applications involving metallic welding. The joints may either be discrete, involving a single interface, or they may· be spatially graded in composition. Extensive theoretical and experimental information exists on discrete bimaterial and trimaterial joints, but relatively little exists for graded joints or composites"

Jan 1, 2000

By Shin-ya Kitamura

Kinetic modeling is very important to understand steelmaking reactions. The coupled reaction model proposed by Prof. D.G.C Robertson is the best suited program, and therefore, the author has applied it to the various steelmaking reactions, a few examples of which are discussed. Hot metal dephosphorization occurs under non-equilibrium conditions as it takes place between the slag, which has a high oxygen potential, and the hot metal, which has a low oxygen potential. A process simulation model based on the coupled reaction model was constructed. This model considers the solid and liquid slag, liquid metal phases, and the reaction between the solid and liquid slag, besides the reaction between the liquid slag and liquid metal. Using this model, the ruling factor to increase the reaction efficiency of dephosphorization has been verified. In the secondary refining process, the values of inclusion composition calculated by the thermodynamic model, under the assumption of equilibrium with the metal composition, were found to be different from those observed in practice. A kinetic model, incorporating the reactions between slag, metal, inclusion, and refractory has been postulated, and the composition change of inclusion during treatment has been analyzed.

Jan 1, 2014

By P. D. Ferro

The direct oxide reduction (DOR) of plutonium oxide generates significant amounts of contaminated waste. This waste primarily consists of calcium oxide-saturated calcium chloride salt. This investigation explores the possibility of recycling the salt, by the electroreduction of the calcium oxide. Fused salt electrolysis of a simulated salt mix (CaC12 + ~10 wt. pct. CaO) is being carried out to electrowin calcium, and the process is being optimized in terms of the calcium solubility, cell temperature, current density and cell design to maximize the current efficiency. This work identifies the major concerns in the development of a process to electrowin calcium from this simulated salt mix.

Jan 1, 1992

By F. J. Tavera

Recently Jameson cell technology has gained acceptance in both mineral and non-mineral applications, mainly because of the high degree of contact between the involved phases in the downcomer, fact that leads to an efficient collection performance. The key for an acceptable performance of the downcomer operation depends on the stability of the jet zone, the mixing zone, and the plug flow zone. in this work the behaviour of the downcomer of a laboratory Jameson cell is reported, as a function of gas hold-up, superficial gas velocity, superficial liquid (or slurry) velocity, and length of the operating zones. The presence of carbon is evaluated in terms of its effect on the gas hold-up and bubble surface area flux. The influence of the downcomer operating conditions on the gas-liquid disengaging cell is presented. Keywords: Jameson cell, downcomer, gas hold-up, mixing, plug flow, conductivity.

Jan 1, 2003

By R. W. Bartlett

A two step process for treating platinum group metal flotation concentrates Is described while experimental results. The process was designed to be simple and Inexpensive While yielding a high recovery and fast turnaround. Ii consists of electric furnace smelting of concentrate to remove gangue and produce a homogeneous sulfide matte containing all of the base metals and platinum group metals. Sulfide oxidation Is minimized during smelting to avoid Installing an acid plant In the second step, matte Is pressure-leached with oxygen In an acid sulfate system to dissolve Iron, nickel, ?and copper while leaving a residue highly concentrated In precious metals, and typically about 1% of the flotation concentrate mass, A batch process with oxygen titration against the base metal composition of the feed Is used to control the end point of the leach. Sulfides must be eliminated while minimizing the precipitation of hydrolysis products. The leach residue can be smelled to bullion to facilitate sampling accuracy.

Jan 1, 1989

By Alexandre Monteiro

Alumina precursor powders can be precipitated from aqueous solutions, using hydrothermal decomposition of urea to deliver base homogeneously to the system. Primary particles agglomerate early in the process, generating a wide size distribution. The presence of a polymeric surfactant such as polyacrylate can suppress or delay agglomeration, reducing particle size and narrowing the size distribution. The stabilization of commercially available a-Alp03 powder with polyacrylate was studied, investigating the effects of polyacrylate molecular weight, ionic strength and temperature. The effect of aluminum concentration, polyacrylate molecular weight and urea concentration on the precipitation of alumina precursors in a sulfate- urea system in the presence of polyacrylate/polyacrylic acid was then studied. The hydrolysis kinetics were followed, and particle sizes were determined. Precipitates were further characterized using energy dispersive spectroscopy. The particle characteristics are discussed in terms of the process conditions.

Jan 1, 1994

By Lin Yang, Yuanbo Zhang, Zhuoxuan Li, Guanghui Li, Jinghua Zeng, Tao Jiang

A technique has been proposed for recovering iron from hematite-rich diasporic-type bauxite ore in this study. Direct reduction roasting followed by low intensity wet magnetic separation process was carried out. The parameters including reduction temperature and time, sodium salts, grinding conditions and magnetic field intensity for separation of iron were determined. The optimum process parameters as follows: roasting temperature of 1050 oC, time of 60 min, sodium salts involving sodium sulfate, borax, sodium carbonate with dosages of 10 wt%, 2 wt%, 35 wt% respectively, and magnetic field intensity of 1000 Gs with fineness of pulp reached 92.75% passing -0.074mm. Under the optimal conditions, an iron concentrate containing 88.17% total iron grade and iron recovery of 92.51% was obtained, 4.55% total iron grade in tailings. This novel technique provide a potential route for utilizing hematiterich diasporic bauxite ore, recovering iron resource firstly, and extracting alumina from magnetic separation tailings further.

Jan 1, 2015

By Evan O. Jones

Processes involving distillation under reduced pressure were developed at the Pacific Northwest Laboratory several years ago to recover spent acid solutions generated during the manufacture of nuclear fuel for the N-Reactor at the Hanford site. Following construction and testing of a pilot-plant, the technology was licensed to Viatec Recovery Systems, Inc. for commercialization. The technology developed included specialized distillation and rectification of volatile acids, removal of water and/or volatile acid from sulfuric acid, and precipitation of salts. A key feature of the Waste Acid Detoxification and Reclamation (WADR) technology is the development and use of advanced thermoplastic and fluoropolymer materials of construction in all critical process equipment. The technology was then expanded to include crystallization to recover metal salts for possible reuse. Economic and environmental advantages of the procedures include recovery of acids for reuse, simplification or elimination of the disposal of waste solutions, and possible recovery of metals. Industries expected to benefit from such applications include galvanizing, electroplating, sand leaching and any where metals are cleaned in acid solutions. Currently a modular system has been assembled for recovery of several different spent acid solutions.

Jan 1, 1995

By Stephen J. Hales

State-of-the-art Resistance Spot Welding (RSW) equipment has the potential to permit adaptive feedback through recent advances in computerized process control. The initial step toward achieving this goal involves assessment of the effect of specific variables and the interaction between these process inputs on spot weld characteristics. This investigation addresses this issue through the application of Taguchi methodology to understand and refine a RSW schedule developed for joining of two dissimilar aluminum-lithium (AI-Li) alloys of different nominal thickness. The experiment was designed to establish a hierarchy of inputs with respect to each 'other, and to determine the significance of these inputs with respect to experimental noise. Valuable insight was gained regarding the interaction between process variables and the effect of certain equipment-related changes. In spite of a decrease in equipment performance, an improvement in the maximum strength attainable for defect-free spot welds resulted from the application of the statistical experiment.

Jan 1, 1992

By Patrice Chartrand, Halvor Dalaker, Philippe Ouzilleau

A size-dependant thermodynamical model for the carbon-hydrogen previously developed by Ouzilleau et al. [1] has been expanded here to include chemisorption of methyl groups. Gibbsenergy minimalisation calculations using FACTSAGE software on this model indicates that hydrogen bonding through methyl groups is energetically favoured as an intermediate between bonding as monoatomic hydrogen to edge hexagons (which is more favourable) and as monoatomic hydrogen to corner hexagons (which is less favourable). The model has also been applied to methane decomposition and oxide reduction using natural gas. A C-H solid solution as a thermodynamic description of the solid carbon phase influences calculations of carbon activity in metastable methane, and gives different results than when using graphite.

Jan 1, 2015

By Richard D. Hagni

Ore microscopy is a useful technique to detect and study the ore minerals that are associated with sediment-hosted and volcanic-hosted deposits of finely disseminated gold and silver. Ore microscopy can be used to determine the: 1) precious metal-bearing minerals in some ores, 2) associated ore minerals that may form geochemical exploration halos, 3) character of iron sulfide grains, 4) extent of sulfide oxidation, 5) character of oxidized iron minerals, 6) character of original sulfide grains from a study of the hypogene and supergene oxidized ores, 7) relative time of oxidation, 8) character of organic matter, 9) minerals that may consume excessive amounts of cyanide solution, 10) extent of silicification and silica encapsulation, and 11) possibility of salting.

Jan 1, 1987

By S. J. Gerdemann

The U.S. Bureau of Mines is studying the kinetics of wet oxidation of sphalerite concen- trate (ZnS) as a possible process for a gravity-pressurized reactor (GPR). At tempera- tures in excess of 200' C, a sphalerite water slurry will react with 0, to form zinc sul- fate (ZnSO,). However, the pressure required to keep the water from boiling at these temperatures has kept this reaction from becoming a viable continuous process. The GPR can easily obtain the high pressures required for this reaction. The reaction rate is complicated by the solubility of 0, in water and the further oxidation of ZnSO, to insoluble zinc oxysulfate (Zn4(OH),S04.4H20). The effects of pressure, temperature, and particle size on the rate of reaction were investigated. Reaction rate was found to be limited by the amount of oxygen in solution. However, at 250" C and 1500 psia, over 90 pct of the zinc was solubilized in less than an hour. The conditions for maxi- mizing the Zn++ in solution, while minimizing oxysulfate formation, are discussed.

Jan 1, 1993

By Hao Deng, Hongmin Zhu, Jichao Li, Kai Huang

"Silicon and silicon carbide mixing micropowders obtained from the saw cutting industry of polycrystalline silicon ingot is separated by a simple sequential sedimentation. The Zeta potentials of the powders in the aqueous suspension are adjusted by varying the pHs with dilute acid or alkaline reagents. The dispersion and aggregation content of the microparticles is significantly influenced by pHs, and so their settlement velocity in the same hydraulic conditions are quite different, and silicon powders tend to suspend in the upper section of the suspension for its finer size and smaller density under the stronger Zeta potential repulsion force. The original content of the cutting powders with 30%wt silicon are separated into the Si-rich and SiC-rich powder respectively, and 62%wt Si-rich powder can be obtained after 4 times of sedimentation under pH = 8.0, showing the great potential for Si and SiC powder separation and recovery in a cost-effective way.IntroductionWith the fast development of photovoltaic (PV) technology these years, the market demand for the solar-grade high pure silicon material significantly increased, making the silicon recycling and recovery from the wire sawing slurry profitable and attractive[1]. Waste silicon slurry was produced in the multi-wire sawing process of a silicon ingot by using an ethylene glycol-based solution and silicon carbide abrasives as the slicing system. During this slicing process, about 30% of the silicon ingot will become the waste as the fine particles suspended in the slurry, which mainly consists of silicon kerf-loss particles, SiC fragmental particles, tiny iron fragments from the worn sawing wire and ethylene glycol-based solution [2]. The separation of above individual component is usually easy except for Si and SiC fine particles for their quite similar properties. So the biggest challenge for the effective recovery and recycling of silicon particles from the wire sawing slurry actually lies in the mutual separation of silicon and silicon carbide particles."

Jan 1, 2012