Search Documents

By F. Shahbazian

attempt to systematize the knowledge on slag viscosities, the present work was carried out. The Among the physical properties of slags, viscosity is very important in understanding the mass out in the temperature range 1438-1762 Q The rotating cylinder method was used in the viscosity measurements. Crucibles and spindles made out of pure iron were employed. The transfer phenomena in metallurgical processes. The viscosities of fayalitic slags are of great interest in the non-ferrous metal industry, with special reference to copper production. In an slags were prefused before the measurements. In order to take into account the vaporization reactions involving CaF2, pre- and post measurement samples of the slags were chemically analysed and the compositions were ascertained. The results show that in the case of the CaO-SiO2 system, CaF2 additions tend to decrease the viscosity, in accordance with the expectations. In the case of the "FeO"-SiO2 system, at higher "FeO" / SiO2 ratios in the slags, a reverse trend was observed. The results are discussed on the basis of a viscosity model for silicate melts developed in the present laboratory as well as the structural considerations of silicates.

Jan 1, 2000

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"Drying (water removal) prior to smelting is always economically feasible. Unnecessary heating of vapour can thus be eliminated resulting in savings of5-15 MUSD every year.Thermodynamically removal of one ton of water out of copper concentrate at 100 °C (with 10 % moisture) requires approximately 3150 MJ/tH2o, consisting of heating of the water (377 MJ), heating of the concentrate (509 MJ) and water evaporation (2260 MJ). This is quite independent of the selected drying technology. In reality some more heat is needed as higher temperature is practiced to enhance the drying performance and to reduce the equipment size.Major nominator in drying energy efficiency is amount of gases, which depends greatly on the drying technology. Dryers based on direct heating with fossil fuels have high gas flow rates, and thus they require additional energy of about 1400-1600 MJ/tH2o, compared to indirect modemsteam drying at 250-400 MJ/tH2o.Significant benefits in energy consumption (900-1300 MJ/tH2o) with additional potential for a bonus profit of 2-4 MUSD/y year, together with full elimination of some 40 000 tpy CO2 per mid-size dryer is available by selecting sustainable, energy efficient steam drying.IntroductionRemoval of water from the concentrate is very energy intensive thus having a significant environmental impact. However, drying prior to smelting is always economically feasible and very often viable also from the perspective of process operations. This environmental impact of drying can, however, be decreased or even fully eliminated with proper selection of the drying technology.Energy incorporated in drying consists always of a number of phases like liquid (water), solids (concentrate) and gases (water vapour, purging I dilution air, combustion gases). Each phase is heated to a specific temperature during the drying process.Heating of water, heating of the concentrate and water evaporation consumes more or less the same amount of energy despite of the drying technology (3150 MJ per ton of water). In conventional drying this amount of energy is achieved by combustion of fossil fuels wirg subsequent CO2 emission. Alternatively, chemical energy derived from sulphide smelting can be utilized in a form of steam thus generating zero emission ofCO2, in modem steam drying."

Jan 1, 2012

By R. Hurman Eric

The flow of molten slag and matte and the estimation of the mass of settled matte in electric furnaces is discussed and the action of the electric furnace as a settler is considered. Particle size of the concentrate and its grade are major contributors to settler dimensions. Discussion on the production capacity of the electric furnace with reference to operating current, power input, furnace dimensions such as width and length and electrode diameter are given. These discussions are based on considerations derived mainly from experimentally determined properties of the slag such as its resistivity, viscosity and liquidus temperature. Extension of the design and operating considerations to circular furnace symmetry is also discussed.

Jan 1, 1995

By I. D. Reznik

Results of thermodynamic computations have been presented for reactions occurring in the process of segregation roasting of oxide nickel ores to describe more accurately the mechanism of the process. Under conditions of laboratory-scale roasting in combination with close-circuit flotation flow-sheets and magnetic separation, a recovery of 80-82% of nickel into 8 to 10% Ni concentrate and a recovery of up to 66% of cobalt was achieved. Process conditions have been selected for processing of both high-iron and high-magnesium ores. The feasibility of conversion of 94-98% of nickel and cobalt into solution by oxidizing pressure leaching with sulfuric acid has been demonstrated. It has been substantiated that it is reasonable to introduce double-stage segregation roasting.

Jan 1, 2003

By Yongqi Sun, Zuotai Zhang

Hot slags, at the temperatures of 1450-1650 oC, carry a substantial amount of high quality thermal energy, which represents the largest undeveloped energy source in the steel industry. However, the waste heat recovery rate in China is less than 2%; thus there is a great potential of waste heat recovery. In this study, we investigated a chemical method to extract the waste heat from high temperature blast furnace slags, i.e., sludge gasification. Sewage sludge, another substantial waste produced in the municipal system, need to be timely disposed, the organics of which could be gasified using the waste heat in the slags for the purpose of syngas production. Both the kinetics and thermodynamics of the sludge gasification process were clarified here. Most importantly, an integrated system composed of multiple systems such as the steel industry, the cement industry, the municipal system and the chemical engineering industry, was analyzed in this study.

Jan 1, 2016

By Susumu Okabe

Injection metallurgy is widely adopted in various fields of metallurgical operations to achieve high productivity. The Mitsubishi Continuous Copper Smelting and Converting Process employs the top blown lance technique for the continuous supply of solid charges and reaction gases into the molten bath, where the agitated bath contributes to enhance the heat and mass transfer and the increased gas/liquid interface area accelerates the reaction. However, excessive splashing of the molten materials accompanied by the injection may cause an unexpected wear of the furnace lining. In order to estimate the splashing rate quantitatively, and to optimize the furnace design and the blowing condition, a physical model study of the top blown gas injection onto the liquid bath was carried out. An equation of the splashing rate was obtained as the function of cavity size, gas velocity and bath properties.

Jan 1, 1995

By Ehsan Khajeh

In this study, the permeabilities of Al-15.5wt%Cu and Al-19.5wt%Cu have been determined by solving the full Navier-Stokes equations on 3D geometries of interdendritic channels obtained by X-ray microtomography (XMT). The samples for XMT were sectioned from different positions in directionally solidified cylinders in order to obtain a variety of microstructures for each composition. The flow has been solved using a 2nd-order accurate Finite Volume Method (FVM) approach. The effect of employing uniform or unstructured mesh on the calculated permeability has been studied. The Marching-cube triangulation method was necessary to extract accurate surfaces for unstructured volume meshing. Calculated values of permeability for this range of solid fractions show partial agreement with previous experiments. Observed deviations are attributed to the difficulties of experimental permeability measurements.

Jan 1, 2009

By H. Kaffash

Ferromanganese is a ferroalloy with high manganese content which finds many uses for example as deoxidizer in steelmaking industry. However, there is very little data on the dissolution rate of carbonaceous materials in Mn containing metals. In this paper, the kinetic analysis of carburization reactions is investigated for Mn–Fe alloys. Dissolution rate of graphite in pure iron and four different alloys with 10 wt%, 40 wt%, 60 wt% and 85 wt% manganese at 1823 K was studied. Results showed that the dissolution rate of carbon from graphite increased with increasing time for all alloys. The dissolution rate constant increased with the increasing manganese content from 6.5 × 10−3 cm/s for 0%Mn to 23.6 × 10−3 cm/s for 85%Mn.

By Olusegun J. Ilegbusi

"A two-fluid model is used to calculate flow and heat transfer characteristics of a plasma jet. This model accounts for both gradient-diffusion mixing and unmixing that may result from pressure-gradient-body-force imbalance in the system. The unmixedness is considered to be essentially a Rayleigh-Taylor kind instability. Separate transport equations are solved for the plasma and ambient gas velocities, temperatures and volume fractions. The two fluids allowed to exchange mass, momentum and energy through empirical interaction parameters. The empirical coefficients are first established by comparison of predictions with available experimental data for shear flows. The model is then applied to an Argon plasma jet ejecting into stagnant air. The predicted results show the significant build-up of unmixed air within the plasma gas, even relatively far downstream of the plasma torch. By adjusting the inlet condition, the model adequately reproduces the available experimental data on the temperature profile.IntroductionPlasma jets have important applications in materials processing, some of which include spray deposition, melting and refining, heat treatment and materials synthesis. In a typical reactor, the hot plasma stream entrains a surrounding gas and the resulting heat and mass transfer and the condition of operation of the torch, determines to a large extent, the performance of the unit. The entrainment may prevent uniform mixing and produce regions of unmixed hot/cold gases and non-uniform deposits as a result of insufficient melting of deposit in cold regions. This phenomenon may also affect chemical reaction rate in plasma systems for NOx reduction in exhaust gases.The study of plasma phenomena is often conveniently divided into three parts namely, the plasma torch, the plasma jet and analysis of the particles carried in the jet. The present work concerns processes occuring in the near-field of the plasma jet i.e. just downstream of the torch."

Jan 1, 1994

By Eduardo Juncal, Jorge Alberto Soares Tenorio, Jose Roberto de Oliveira, Denise Crocce Romano Espinosal

"Steel industry has been expanding every year, consequently there has been an increase in waste generation in this area. Thus, companies in this sector are finding it difficult to give a correct destination of waste. For example, only in a basic oxygen furnace (BOF) converter are generated about l8kg of dust per ton of steel. The aim of this work was the characterization of dust generated in the BOF converter. The characterization was performed by chemical analysis (titration for iron and its oxides and Inductively Coupled Plasma Atomic Emission Spectroscopy for other elements), scanning electron microscopy, size analysis using Mastersizer 2000 equipment and X-ray diffraction. It was observed that dust is composed mainly iron in form of magnetite, metallic iron and wustite with approximately 99% of the particle size below 100 µm.IntroductionToday, steel is a important metal for the world. It can be produced for two routes, blast furnace/ basic oxygen furnace (BOF) converter and electric arc furnace (EAF) [1].First route, the iron is produced from the reduction of iron ore and coke for fuel injection and! or natural gas for a production of pig iron in blast furnace. The pig iron is sent until BOF converter to perform the blowing of oxygen to obtain the steel. In the second route, the steel is produced using scraps or direct reduced iron (DR!) using electric arc.During steel production are generated a lot of wastes like slag, sludges, scraps and dust [2]. Only in the first six months of201O, world steel production totaled 706 million tons [3]. According to Watson and Wang [4], some 10 to 20 kg of dust is generated per tonne of liquid steel produced. Thus, the reuse of these wastes can be a great to companies, because it reduces the amount of raw material to be extracted and reducing disposal costs [5,6]."

Jan 1, 2012

By Nelson Collao I.

Loss of the organic phase from solvent extraction circuits is a major cost factor for SXEW operations. Recognized sources of loss include evaporation, entrainment, and biological degradation. The mechanisms for both entrainment and evaporative losses are well recognized. Biological degradation of the organic has not been as extensively evaluated as the other mechanisms but is a major source of loss. This paper discusses the impact of biological degradation on an operating plant, potential mechanisms for degradation, conditions under which biodegradation of plant organic can occur and plant conditions that may assist in promoting biodegradation.

Jan 1, 2003

Physical and chemical methods were investigated to tower thorium levels in Eneabba Ilmenite from the natural levels of 180-500 ppm to give Becher Process synthetic rutile with less than 100 ppm thorium. Chemlcal treatments, but not physical separations were successful. A pilot plant trial of a sodium hydroxide leach (25M NaOH at 75°C and 40 wt% solids for Ih) followed by a sulphuric acid leach (3M H2S04 at 90°C and 60 wt% solids for 211) confirmed that thorium could be removed to below 100 ppm. However, the activity of the ilmenite was not lowered to the same extent

Jan 1, 1996

By A. V. Tarasov

Emission of sulfur-containing gases causes most adverse impact on the natural environment in the process of nonferrous metals production. Under the conditions of Arctic regions, in particular in the region of the Norilsk Mining and Metallurgical Complex (Russia), this problem requires a special approach taking into account potential economic and socioeconomic consequences. By reducing the iron sulfide content of flotation concentrates by using new flotation reagents inhibiting pyrrhotite flotation and by applying advanced process flowsheets for flotation it is possible to increase the nonferrous metals content of flotation concentrates by 5% or more along with a corresponding reduction in SO2 formation during their subsequent pyrometallurgical processing. The ways used to resolve the environmental problems in the Norilsk region in the process of nickel and copper production, are based on the improvement of methods for elemental sulfur recovery from metallurgical off-gas by non-conventional techniques, the sulfur recovery from metallurgical gases by production of liquid sulfur dioxide and the technology for pyrometallurgical treatment of sulfide concentrates without SO2 formation. Another opportunity is the development and commercial introduction of hydrometallurgical technologies for treating copper-nickel sulfide ores.

Jan 1, 2006

By Zhang Qin

Dolomite is main impurity mineral in phosphate ores. In practice of phosphate ores production, the grade of concentrates is only containing P2O5 31-32%.In this study, even the increasing of floatation reagent consumption and decreasing of floatation recovery, economic performance is estimated high according to the decreasing of H2SO4 consumption in subsequent production of phosphate fertilizer and the increasing of products value. In floatation stage, influence factor include the synergism impacts of floatation collector, the stages, time, concentration of ore pulp, which were discussed respectively in this paper. Raw material is characterized by mineralogy, chemical analysis, the grain size analysis and milling test . The results show that the grade of concentration can reach to P2O5 36% by deeply de-magnesium oxide from phosphate ores by floatation , which yield a high added value.

Jan 1, 2009

By J. Borlée, J. P. Birat

"ULCOS is a large European program launched by a consortium of 48 partners led by arcelor and a core group of steel producers, which was started in 2004 with the support of the European Commission (RFCS and 6FP programs) to search for breakthrough process routes that could, in the future, when fully developed, demonstrate the potential of large cuts in CO2 emissions for the production of steel from iron ore.The timescale for commercial implementation is the post-Kyoto period, i.e. 15 to 20 years from today.The present paper presents the progress made in the first 2 years of this 5 year program.Several concepts are being investigated in parallel: re-engineering of the blast furnace to incorporate CCS in the core of the process, smelting reduction with CCS capabilities, massive use of natural with more CO2-lean technologies than today, hydrogen steelmaking and electrolysis of iron ore. Biomass also offers very attractive perspectives, while raising major challenges.None of these new steelmaking routes are ""no regret"", which means that the European Steel Industry has already incorporated extensive energy saving steps in its present process technology and is working as close to thermodynamics limits as is cinematically and economically feasible, and that decreasing GHG emissions further means introducing breakthrough technologies that add significant costs to the operation of the Steel Mills.They will also require much research and development before they can be proven and implemented commercially.IntroductionThe ULCOS program (Ultra Low CO2 Steelmaking) is a large research program of the European Steel Industry and its industrial and research partners launched in September 2004 to investigate steelmaking technologies that have the potential of reducing the CO2 emission of the Industry by a large amount, typically in the order of 50%. It is supported in the European Community by the 6th Framework and the RFCS programs through 3 complementary European projects [1,2].The present paper summarizes the work carried out in the phase 1 of ULCOS and in framing the program of phase 2."

Jan 1, 2008

By Gordon A. Irons

"Powder injection for melt refining is widely practiced in the steel industry, and is gaining acceptance in the non-ferrous industries. In these commercially-important systems, the thermodynamics and kinetics may be very complicated. More than one element may be removed by refining, and often the refining agents are not just one compound. In this paper, the thermodynamic and kinetic aspects of these processes are reviewed. A number of examples are given, such as the desulphurization of iron with a variety of reagent mixtures, and selenium removal from copper with several different reagent combinations.IntroductionI am very pleased and honored to present a paper at this Symposium recognizing the many contributions of Professor Howard Womer. Even at the time I was an undergraduate student, the WORCRA process was part of the curriculum. I remember at the time that I was fascinated by the concept, and due to it and the many other rapid developments in Process Metallurgy, I chose it as my field of study. I think the Symposium is testimony that Professor Womer has touched the lives of many others as well.My original assignment was an overview of the basic aspects of gas and solids injection. However, I reviewed most of this material at the Savard/Lee Symposium [1]. In the present paper, I will present some of the basic issues related to refining with powder injection, using work that we have recently completed in both ferrous and non-ferrous systems."

Jan 1, 1996

By Dajian Wang

To obtain the thermodynamic properties of a multicomponent liquid alloy system over the whole range of concentration at an arbitrary temperature, the free volume cell theory has been applied to derive the formula of activity coefficients of liquid solutions based on the infinitely dilute solutions at some temperature. The linear logarithmic relationship between activity coefficients of binary dilute solutions and reciprocal of absolute temperature have been verified, and are in good agreement with the experimental values from the literature. The Monte-Carlo algorithm was used to calculate the nonlinear end value equations of binary systems, then the free volume parameters obtained were correlated with the activity coefficients of liquid binary, ternary, and quaternary systems at an arbitrary temperature. Three dimensional a-X-T diagrams of some binary systems representing the temperature and concentration dependence of activities were plotted. The calculated results regarding non-ferrous alloy systems have been statistically examined with the experimental values from the literature. Hence, this simple approach could be useful for analyzing thermodynamic properties of liquid alloy systems.

Jan 1, 2000

By Guy Xueyi

The environmental impact assessment of the Imperial Smelting Process for metallic zinc and lead production in Shaoguan Smelter, China, was carried out by the life cycle assessment method. The detailed inventory analysis of the Input/Output in the process during 1998-2000 was conducted and the allocation was done among the main products of zinc, lead and sulfuric acid, according to the system expansion and substitution principle, The environmental impacts were assessed by using the following five Eco-indicators: Gross Energy Requirement (GER), Global Warming Potential (GWP), Acidification Potential (AP), Heavy Metal Toxicity' (HMT) and Solid Waste Burden (SWB). The results from this study are useful to address the environmental situation of the technology practice in this smelter, and provide a scientific basis for the further improvement.

Jan 1, 2003

By D. Mukerjee, Ramen Datta, Sanak Mishra, R. Veeraraghavan, K. L. Rohira

"Recent efforts at Steel Authority of India Limited (SAIL) has led to the successful development of atmospheric and marine corrosion resistant high tensile Thermo Mechanically Treated (TMT) bars with minimum specified yield strength of 50 kg.mm-2. These rebars are increasingly being used for a wide range of end-applications, namely, concrete reinforcement structures, bridges, flyovers, dams etc. Welding is an important processing tool for each of the above applications. In view of the importance of welding, a comprehensive evaluation of the weldability properties has been carried for the two grades of steels using Submerged Metal Arc Welding (SMAW) process; the most popularly used technique of welding of reinforcement bars (re bars).Implant tests were conducted to assess the cold cracking susceptibility of the steels. The static fatigue limit (SFL) value, determined for the atmospheric corrosion resistant (Cu-TMT) rebars under no preheat and no rebalcing conditions was found to be 63.8 kg mm-2, which was significantly higher than the Minimum Specified Yield Strength (MSYS) (50 kg.mm-2). This indicates adequate resistance to hydrogen induced cracking (HIC). On the other hand, the SFL value obtained for the marine corrosion resistant rebars (Cu-Cr TMT) under no preheat, no rebaking conditions was found to be inconsistent. Repeat of the test with fully rebaked electrodes (350°C-2h) resulted in a high SFL value (60.3 kg mm-2)_The rigidity of the structure or restraint influences the susceptibility of the weld joint to cracking. The cracking tendency increases with restraint intensity (K) of an assembly. The critical restraint intensities determined for the two steels were found to be· in excess of 1680 kg/mm.mm, indicating good welding behaviour with the following welding conditions : for Cu-TMT rebars with no preheat and no rebaking and for Cu-Cr TMT rebars with no preheat and fully baked electrodes; that is under low hydrogen levels."

Jan 1, 1998

By Samantha Moodley, Rauf Hurman Eric, Cevat Kucukkaragoz, Aditya Kale

"Two titania slags, rutile and synthetic rutile were chlorinated with petroleum coke and CO in a small bubbling fluidized bed reactor. The study aims to identify differences in chlorination mechanism, compare conversion rates, blowover and the chlorination of impurities for the various titania feedstocks at different temperatures.Chlorination rates were highest at 1000ºC; rutile chlorination significantly increases as temperature increases from 800ºC to 1000ºC. At 1000ºC, synthetic rutile had the highest chlorination conversion rate; this was followed by Slag B which in turn was more reactive than Slag A and rutile. The mechanism for slag, synthetic rutile (SR) and rutile chlorination differs. Synthetic rutile feed is porous, providing a larger surface area for the chlorination reaction, hence the highest conversion rates was attained. Titania slag becomes porous with the initial chlorination of FeO and MnO whilst rutile remains solid. As the porosity of slag particles increases so does its tendency to be elutriated. Ti2O3 is oxidized within the early stages of chlorination during the chlorination of FeO and MnO. Ti2O3 not oxidized is then rapidly chlorinated.IntroductionTitanium dioxide (TiO2) is the most common compound of titanium, about 95 - 98% of extracted titanium minerals is processed into TiO2 white pigment [1]. Two processing routes exist for the production of TiO2 pigments, i.e., sulphate and chloride based processes. In the chloride process, titania feedstock is fed to a fluidized bed reactor together with reductant and chlorine gas. A temperature of 1000 - 1300ºC is maintained in the reaction zone and apart from silica, zirconia, uranium and thorium, virtually all the metal oxides in the feed are converted to their respective chlorides [2]. Chlorine is recovered and recycled back to the reactor."

Jan 1, 2012